diff options
Diffstat (limited to 'arch/arm/mach-omap2/board-omap3beagle.c')
| -rw-r--r-- | arch/arm/mach-omap2/board-omap3beagle.c | 429 |
1 files changed, 211 insertions, 218 deletions
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 7f21d24bd43..e2e52031f05 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -20,40 +20,71 @@ #include <linux/clk.h> #include <linux/io.h> #include <linux/leds.h> +#include <linux/pwm.h> +#include <linux/leds_pwm.h> #include <linux/gpio.h> #include <linux/input.h> #include <linux/gpio_keys.h> -#include <linux/opp.h> +#include <linux/pm_opp.h> +#include <linux/cpu.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> #include <linux/mtd/nand.h> #include <linux/mmc/host.h> +#include <linux/usb/phy.h> #include <linux/regulator/machine.h> #include <linux/i2c/twl.h> -#include <mach/hardware.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> #include <asm/mach/flash.h> -#include <plat/board.h> -#include <plat/common.h> #include <video/omapdss.h> -#include <video/omap-panel-generic-dpi.h> -#include <plat/gpmc.h> -#include <plat/nand.h> -#include <plat/usb.h> -#include <plat/omap_device.h> +#include <video/omap-panel-data.h> +#include <linux/platform_data/mtd-nand-omap2.h> +#include "common.h" +#include "omap_device.h" +#include "gpmc.h" +#include "soc.h" #include "mux.h" #include "hsmmc.h" -#include "timer-gp.h" #include "pm.h" +#include "board-flash.h" #include "common-board-devices.h" +#define NAND_CS 0 + +static struct pwm_lookup pwm_lookup[] = { + /* LEDB -> PMU_STAT */ + PWM_LOOKUP("twl-pwmled", 1, "leds_pwm", "beagleboard::pmu_stat", + 7812500, PWM_POLARITY_NORMAL), +}; + +static struct led_pwm pwm_leds[] = { + { + .name = "beagleboard::pmu_stat", + .max_brightness = 127, + .pwm_period_ns = 7812500, + }, +}; + +static struct led_pwm_platform_data pwm_data = { + .num_leds = ARRAY_SIZE(pwm_leds), + .leds = pwm_leds, +}; + +static struct platform_device leds_pwm = { + .name = "leds_pwm", + .id = -1, + .dev = { + .platform_data = &pwm_data, + }, +}; + /* * OMAP3 Beagle revision * Run time detection of Beagle revision is done by reading GPIO. @@ -61,7 +92,8 @@ * AXBX = GPIO173, GPIO172, GPIO171: 1 1 1 * C1_3 = GPIO173, GPIO172, GPIO171: 1 1 0 * C4 = GPIO173, GPIO172, GPIO171: 1 0 1 - * XM = GPIO173, GPIO172, GPIO171: 0 0 0 + * XMA/XMB = GPIO173, GPIO172, GPIO171: 0 0 0 + * XMC = GPIO173, GPIO172, GPIO171: 0 1 0 */ enum { OMAP3BEAGLE_BOARD_UNKN = 0, @@ -69,14 +101,28 @@ enum { OMAP3BEAGLE_BOARD_C1_3, OMAP3BEAGLE_BOARD_C4, OMAP3BEAGLE_BOARD_XM, + OMAP3BEAGLE_BOARD_XMC, }; static u8 omap3_beagle_version; -static u8 omap3_beagle_get_rev(void) -{ - return omap3_beagle_version; -} +/* + * Board-specific configuration + * Defaults to BeagleBoard-xMC + */ +static struct { + int mmc1_gpio_wp; + bool usb_pwr_level; /* 0 - Active Low, 1 - Active High */ + int dvi_pd_gpio; + int usr_button_gpio; + int mmc_caps; +} beagle_config = { + .mmc1_gpio_wp = -EINVAL, + .usb_pwr_level = 0, + .dvi_pd_gpio = -EINVAL, + .usr_button_gpio = 4, + .mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA, +}; static struct gpio omap3_beagle_rev_gpios[] __initdata = { { 171, GPIOF_IN, "rev_id_0" }, @@ -111,18 +157,34 @@ static void __init omap3_beagle_init_rev(void) case 7: printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n"); omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX; + beagle_config.mmc1_gpio_wp = 29; + beagle_config.dvi_pd_gpio = 170; + beagle_config.usr_button_gpio = 7; break; case 6: printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n"); omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3; + beagle_config.mmc1_gpio_wp = 23; + beagle_config.dvi_pd_gpio = 170; + beagle_config.usr_button_gpio = 7; break; case 5: printk(KERN_INFO "OMAP3 Beagle Rev: C4\n"); omap3_beagle_version = OMAP3BEAGLE_BOARD_C4; + beagle_config.mmc1_gpio_wp = 23; + beagle_config.dvi_pd_gpio = 170; + beagle_config.usr_button_gpio = 7; break; case 0: - printk(KERN_INFO "OMAP3 Beagle Rev: xM\n"); + printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n"); omap3_beagle_version = OMAP3BEAGLE_BOARD_XM; + beagle_config.usb_pwr_level = 1; + beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA; + break; + case 2: + printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n"); + omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC; + beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA; break; default: printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev); @@ -163,122 +225,96 @@ static struct mtd_partition omap3beagle_nand_partitions[] = { /* DSS */ -static int beagle_enable_dvi(struct omap_dss_device *dssdev) -{ - if (gpio_is_valid(dssdev->reset_gpio)) - gpio_set_value(dssdev->reset_gpio, 1); - - return 0; -} +static struct connector_dvi_platform_data beagle_dvi_connector_pdata = { + .name = "dvi", + .source = "tfp410.0", + .i2c_bus_num = 3, +}; -static void beagle_disable_dvi(struct omap_dss_device *dssdev) -{ - if (gpio_is_valid(dssdev->reset_gpio)) - gpio_set_value(dssdev->reset_gpio, 0); -} +static struct platform_device beagle_dvi_connector_device = { + .name = "connector-dvi", + .id = 0, + .dev.platform_data = &beagle_dvi_connector_pdata, +}; -static struct panel_generic_dpi_data dvi_panel = { - .name = "generic", - .platform_enable = beagle_enable_dvi, - .platform_disable = beagle_disable_dvi, +static struct encoder_tfp410_platform_data beagle_tfp410_pdata = { + .name = "tfp410.0", + .source = "dpi.0", + .data_lines = 24, + .power_down_gpio = -1, }; -static struct omap_dss_device beagle_dvi_device = { - .type = OMAP_DISPLAY_TYPE_DPI, - .name = "dvi", - .driver_name = "generic_dpi_panel", - .data = &dvi_panel, - .phy.dpi.data_lines = 24, - .reset_gpio = -EINVAL, +static struct platform_device beagle_tfp410_device = { + .name = "tfp410", + .id = 0, + .dev.platform_data = &beagle_tfp410_pdata, }; -static struct omap_dss_device beagle_tv_device = { +static struct connector_atv_platform_data beagle_tv_pdata = { .name = "tv", - .driver_name = "venc", - .type = OMAP_DISPLAY_TYPE_VENC, - .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO, + .source = "venc.0", + .connector_type = OMAP_DSS_VENC_TYPE_SVIDEO, + .invert_polarity = false, }; -static struct omap_dss_device *beagle_dss_devices[] = { - &beagle_dvi_device, - &beagle_tv_device, +static struct platform_device beagle_tv_connector_device = { + .name = "connector-analog-tv", + .id = 0, + .dev.platform_data = &beagle_tv_pdata, }; static struct omap_dss_board_info beagle_dss_data = { - .num_devices = ARRAY_SIZE(beagle_dss_devices), - .devices = beagle_dss_devices, - .default_device = &beagle_dvi_device, + .default_display_name = "dvi", }; -static struct regulator_consumer_supply beagle_vdac_supply = - REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); - -static struct regulator_consumer_supply beagle_vdvi_supplies[] = { - REGULATOR_SUPPLY("vdds_dsi", "omapdss"), - REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"), -}; - -static void __init beagle_display_init(void) -{ - int r; - - r = gpio_request_one(beagle_dvi_device.reset_gpio, GPIOF_OUT_INIT_LOW, - "DVI reset"); - if (r < 0) - printk(KERN_ERR "Unable to get DVI reset GPIO\n"); -} - #include "sdram-micron-mt46h32m32lf-6.h" static struct omap2_hsmmc_info mmc[] = { { .mmc = 1, - .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA, - .gpio_wp = 29, + .caps = MMC_CAP_4_BIT_DATA, + .gpio_wp = -EINVAL, + .deferred = true, }, {} /* Terminator */ }; -static struct regulator_consumer_supply beagle_vmmc1_supply = { - .supply = "vmmc", +static struct regulator_consumer_supply beagle_vmmc1_supply[] = { + REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"), }; -static struct regulator_consumer_supply beagle_vsim_supply = { - .supply = "vmmc_aux", +static struct regulator_consumer_supply beagle_vsim_supply[] = { + REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"), }; static struct gpio_led gpio_leds[]; +static struct usbhs_phy_data phy_data[] = { + { + .port = 2, + .reset_gpio = 147, + .vcc_gpio = -1, /* updated in beagle_twl_gpio_setup */ + .vcc_polarity = 1, /* updated in beagle_twl_gpio_setup */ + }, +}; + static int beagle_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned ngpio) { - int r, usb_pwr_level; - - if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) { - mmc[0].gpio_wp = -EINVAL; - } else if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) || - (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C4)) { - omap_mux_init_gpio(23, OMAP_PIN_INPUT); - mmc[0].gpio_wp = 23; - } else { - omap_mux_init_gpio(29, OMAP_PIN_INPUT); - } + int r; + + mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp; /* gpio + 0 is "mmc0_cd" (input/IRQ) */ mmc[0].gpio_cd = gpio + 0; - omap2_hsmmc_init(mmc); - - /* link regulators to MMC adapters */ - beagle_vmmc1_supply.dev = mmc[0].dev; - beagle_vsim_supply.dev = mmc[0].dev; + omap_hsmmc_late_init(mmc); /* * TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active * high / others active low) * DVI reset GPIO is different between beagle revisions */ - if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) { - usb_pwr_level = GPIOF_OUT_INIT_HIGH; - beagle_dvi_device.reset_gpio = 129; + /* Valid for all -xM revisions */ + if (cpu_is_omap3630()) { /* * gpio + 1 on Xm controls the TFP410's enable line (active low) * gpio + 2 control varies depending on the board rev as below: @@ -290,14 +326,10 @@ static int beagle_twl_gpio_setup(struct device *dev, if (r) pr_err("%s: unable to configure nDVI_PWR_EN\n", __func__); - r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH, - "DVI_LDO_EN"); - if (r) - pr_err("%s: unable to configure DVI_LDO_EN\n", - __func__); + + beagle_config.dvi_pd_gpio = gpio + 2; + } else { - usb_pwr_level = GPIOF_OUT_INIT_LOW; - beagle_dvi_device.reset_gpio = 170; /* * REVISIT: need ehci-omap hooks for external VBUS * power switch and overcurrent detect @@ -305,19 +337,21 @@ static int beagle_twl_gpio_setup(struct device *dev, if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC")) pr_err("%s: unable to configure EHCI_nOC\n", __func__); } + beagle_tfp410_pdata.power_down_gpio = beagle_config.dvi_pd_gpio; - gpio_request_one(gpio + TWL4030_GPIO_MAX, usb_pwr_level, "nEN_USB_PWR"); + platform_device_register(&beagle_tfp410_device); + platform_device_register(&beagle_dvi_connector_device); + platform_device_register(&beagle_tv_connector_device); - /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */ - gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; + /* TWL4030_GPIO_MAX i.e. LED_GPO controls HS USB Port 2 power */ + phy_data[0].vcc_gpio = gpio + TWL4030_GPIO_MAX; + phy_data[0].vcc_polarity = beagle_config.usb_pwr_level; + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); return 0; } static struct twl4030_gpio_platform_data beagle_gpio_data = { - .gpio_base = OMAP_MAX_GPIO_LINES, - .irq_base = TWL4030_GPIO_IRQ_BASE, - .irq_end = TWL4030_GPIO_IRQ_END, .use_leds = true, .pullups = BIT(1), .pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13) @@ -336,8 +370,8 @@ static struct regulator_init_data beagle_vmmc1 = { | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS, }, - .num_consumer_supplies = 1, - .consumer_supplies = &beagle_vmmc1_supply, + .num_consumer_supplies = ARRAY_SIZE(beagle_vmmc1_supply), + .consumer_supplies = beagle_vmmc1_supply, }; /* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */ @@ -351,62 +385,15 @@ static struct regulator_init_data beagle_vsim = { | REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS, }, - .num_consumer_supplies = 1, - .consumer_supplies = &beagle_vsim_supply, -}; - -/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */ -static struct regulator_init_data beagle_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &beagle_vdac_supply, -}; - -/* VPLL2 for digital video outputs */ -static struct regulator_init_data beagle_vpll2 = { - .constraints = { - .name = "VDVI", - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(beagle_vdvi_supplies), - .consumer_supplies = beagle_vdvi_supplies, -}; - -static struct twl4030_usb_data beagle_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - -static struct twl4030_codec_audio_data beagle_audio_data; - -static struct twl4030_codec_data beagle_codec_data = { - .audio_mclk = 26000000, - .audio = &beagle_audio_data, + .num_consumer_supplies = ARRAY_SIZE(beagle_vsim_supply), + .consumer_supplies = beagle_vsim_supply, }; static struct twl4030_platform_data beagle_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ - .usb = &beagle_usb_data, .gpio = &beagle_gpio_data, - .codec = &beagle_codec_data, .vmmc1 = &beagle_vmmc1, .vsim = &beagle_vsim, - .vdac = &beagle_vdac, - .vpll2 = &beagle_vpll2, }; static struct i2c_board_info __initdata beagle_i2c_eeprom[] = { @@ -417,6 +404,13 @@ static struct i2c_board_info __initdata beagle_i2c_eeprom[] = { static int __init omap3_beagle_i2c_init(void) { + omap3_pmic_get_config(&beagle_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC | + TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); + + beagle_twldata.vpll2->constraints.name = "VDVI"; + omap3_pmic_init("twl4030", &beagle_twldata); /* Bus 3 is attached to the DVI port where devices like the pico DLP * projector don't work reliably with 400kHz */ @@ -435,11 +429,6 @@ static struct gpio_led gpio_leds[] = { .default_trigger = "mmc0", .gpio = 149, }, - { - .name = "beagleboard::pmu_stat", - .gpio = -EINVAL, /* gets replaced */ - .active_low = true, - }, }; static struct gpio_led_platform_data gpio_led_info = { @@ -458,7 +447,8 @@ static struct platform_device leds_gpio = { static struct gpio_keys_button gpio_buttons[] = { { .code = BTN_EXTRA, - .gpio = 7, + /* Dynamically assigned depending on board */ + .gpio = -EINVAL, .desc = "user", .wakeup = 1, }, @@ -477,36 +467,20 @@ static struct platform_device keys_gpio = { }, }; -static void __init omap3_beagle_init_early(void) -{ - omap2_init_common_infrastructure(); - omap2_init_common_devices(mt46h32m32lf6_sdrc_params, - mt46h32m32lf6_sdrc_params); -} - -static void __init omap3_beagle_init_irq(void) -{ - omap_init_irq(); -#ifdef CONFIG_OMAP_32K_TIMER - omap2_gp_clockevent_set_gptimer(12); -#endif -} +static struct platform_device madc_hwmon = { + .name = "twl4030_madc_hwmon", + .id = -1, +}; static struct platform_device *omap3_beagle_devices[] __initdata = { &leds_gpio, &keys_gpio, + &madc_hwmon, + &leds_pwm, }; -static const struct usbhs_omap_board_data usbhs_bdata __initconst = { - - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, +static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = 147, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -515,35 +489,38 @@ static struct omap_board_mux board_mux[] __initdata = { }; #endif -static void __init beagle_opp_init(void) +static int __init beagle_opp_init(void) { int r = 0; - /* Initialize the omap3 opp table */ - if (omap3_opp_init()) { + if (!machine_is_omap3_beagle()) + return 0; + + /* Initialize the omap3 opp table if not already created. */ + r = omap3_opp_init(); + if (r < 0 && (r != -EEXIST)) { pr_err("%s: opp default init failed\n", __func__); - return; + return r; } - /* Custom OPP enabled for XM */ - if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) { - struct omap_hwmod *mh = omap_hwmod_lookup("mpu"); - struct omap_hwmod *dh = omap_hwmod_lookup("iva"); - struct device *dev; + /* Custom OPP enabled for all xM versions */ + if (cpu_is_omap3630()) { + struct device *mpu_dev, *iva_dev; + + mpu_dev = get_cpu_device(0); + iva_dev = omap_device_get_by_hwmod_name("iva"); - if (!mh || !dh) { + if (!mpu_dev || IS_ERR(iva_dev)) { pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n", - __func__, mh, dh); - return; + __func__, mpu_dev, iva_dev); + return -ENODEV; } /* Enable MPU 1GHz and lower opps */ - dev = &mh->od->pdev.dev; - r = opp_enable(dev, 800000000); + r = dev_pm_opp_enable(mpu_dev, 800000000); /* TODO: MPU 1GHz needs SR and ABB */ /* Enable IVA 800MHz and lower opps */ - dev = &dh->od->pdev.dev; - r |= opp_enable(dev, 660000000); + r |= dev_pm_opp_enable(iva_dev, 660000000); /* TODO: DSP 800MHz needs SR and ABB */ if (r) { pr_err("%s: failed to enable higher opp %d\n", @@ -552,33 +529,47 @@ static void __init beagle_opp_init(void) * Cleanup - disable the higher freqs - we dont care * about the results */ - dev = &mh->od->pdev.dev; - opp_disable(dev, 800000000); - dev = &dh->od->pdev.dev; - opp_disable(dev, 660000000); + dev_pm_opp_disable(mpu_dev, 800000000); + dev_pm_opp_disable(iva_dev, 660000000); } } - return; + return 0; } +omap_device_initcall(beagle_opp_init); static void __init omap3_beagle_init(void) { omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); omap3_beagle_init_rev(); + + if (gpio_is_valid(beagle_config.mmc1_gpio_wp)) + omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT); + mmc[0].caps = beagle_config.mmc_caps; + omap_hsmmc_init(mmc); + omap3_beagle_i2c_init(); + + gpio_buttons[0].gpio = beagle_config.usr_button_gpio; + platform_add_devices(omap3_beagle_devices, ARRAY_SIZE(omap3_beagle_devices)); + if (gpio_is_valid(beagle_config.dvi_pd_gpio)) + omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT); omap_display_init(&beagle_dss_data); - omap_serial_init(); - omap_mux_init_gpio(170, OMAP_PIN_INPUT); - /* REVISIT leave DVI powered down until it's needed ... */ - gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD"); + omap_serial_init(); + omap_sdrc_init(mt46h32m32lf6_sdrc_params, + mt46h32m32lf6_sdrc_params); + usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); + usbhs_init(&usbhs_bdata); - omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions, - ARRAY_SIZE(omap3beagle_nand_partitions)); + + board_nand_init(omap3beagle_nand_partitions, + ARRAY_SIZE(omap3beagle_nand_partitions), NAND_CS, + NAND_BUSWIDTH_16, NULL); + omap_twl4030_audio_init("omap3beagle", NULL); /* Ensure msecure is mux'd to be able to set the RTC. */ omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH); @@ -587,17 +578,19 @@ static void __init omap3_beagle_init(void) omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT); omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT); - beagle_display_init(); - beagle_opp_init(); + pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup)); } MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board") /* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */ - .boot_params = 0x80000100, + .atag_offset = 0x100, .reserve = omap_reserve, .map_io = omap3_map_io, - .init_early = omap3_beagle_init_early, - .init_irq = omap3_beagle_init_irq, + .init_early = omap3_init_early, + .init_irq = omap3_init_irq, + .handle_irq = omap3_intc_handle_irq, .init_machine = omap3_beagle_init, - .timer = &omap_timer, + .init_late = omap3_init_late, + .init_time = omap3_secure_sync32k_timer_init, + .restart = omap3xxx_restart, MACHINE_END |