1 files changed, 1 insertions, 72 deletions
diff --git a/arch/arm/mach-msm/include/mach/entry-macro-qgic.S b/arch/arm/mach-msm/include/mach/entry-macro-qgic.S
index 12467157afb..717076f3ca7 100644
--- a/arch/arm/mach-msm/include/mach/entry-macro-qgic.S
+++ b/arch/arm/mach-msm/include/mach/entry-macro-qgic.S
@@ -8,81 +8,10 @@
  * warranty of any kind, whether express or implied.
  */
 
-#include <mach/hardware.h>
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
 
 	.macro	disable_fiq
 	.endm
 
-	.macro  get_irqnr_preamble, base, tmp
-	ldr	\base, =gic_cpu_base_addr
-	ldr	\base, [\base]
-	.endm
-
 	.macro  arch_ret_to_user, tmp1, tmp2
 	.endm
-
-	/*
-	 * The interrupt numbering scheme is defined in the
-	 * interrupt controller spec.  To wit:
-	 *
-	 * Migrated the code from ARM MP port to be more consistent
-	 * with interrupt processing , the following still holds true
-	 * however, all interrupts are treated the same regardless of
-	 * if they are local IPI or PPI
-	 *
-	 * Interrupts 0-15 are IPI
-	 * 16-31 are PPI
-	 *   (16-18 are the timers)
-	 * 32-1020 are global
-	 * 1021-1022 are reserved
-	 * 1023 is "spurious" (no interrupt)
-	 *
-	 * A simple read from the controller will tell us the number of the
-	 * highest priority enabled interrupt.  We then just need to check
-	 * whether it is in the valid range for an IRQ (0-1020 inclusive).
-	 *
-	 * Base ARM code assumes that the local (private) peripheral interrupts
-	 * are not valid, we treat them differently, in that the privates are
-	 * handled like normal shared interrupts with the exception that only
-	 * one processor can register the interrupt and the handler must be
-	 * the same for all processors.
-	 */
-
-	.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-
-	ldr  \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 =srcCPU,
-						   9-0 =int # */
-
-	bic     \irqnr, \irqstat, #0x1c00	@mask src
-	cmp     \irqnr, #15
-	ldr		\tmp, =1021
-	cmpcc	\irqnr, \irqnr
-	cmpne	\irqnr, \tmp
-	cmpcs	\irqnr, \irqnr
-
-	.endm
-
-	/* We assume that irqstat (the raw value of the IRQ acknowledge
-	 * register) is preserved from the macro above.
-	 * If there is an IPI, we immediately signal end of interrupt on the
-	 * controller, since this requires the original irqstat value which
-	 * we won't easily be able to recreate later.
-	 */
-	.macro test_for_ipi, irqnr, irqstat, base, tmp
-    bic \irqnr, \irqstat, #0x1c00
-    cmp \irqnr, #16
-    strcc   \irqstat, [\base, #GIC_CPU_EOI]
-    cmpcs   \irqnr, \irqnr
-	.endm
-
-	/* As above, this assumes that irqstat and base are preserved.. */
-
-	.macro test_for_ltirq, irqnr, irqstat, base, tmp
-    bic \irqnr, \irqstat, #0x1c00
-    mov     \tmp, #0
-    cmp \irqnr, #16
-    moveq   \tmp, #1
-    streq   \irqstat, [\base, #GIC_CPU_EOI]
-    cmp \tmp, #0
-	.endm