1 files changed, 10 insertions, 57 deletions
diff --git a/arch/arm/mach-clps711x/include/mach/hardware.h b/arch/arm/mach-clps711x/include/mach/hardware.h
index 8497775d6ee..2f23dd5d73e 100644
--- a/arch/arm/mach-clps711x/include/mach/hardware.h
+++ b/arch/arm/mach-clps711x/include/mach/hardware.h
@@ -24,7 +24,10 @@
 
 #include <mach/clps711x.h>
 
-#define CLPS711X_VIRT_BASE	IOMEM(0xff000000)
+#define IO_ADDRESS(x)		(0xdc000000 + (((x) & 0x03ffffff) | \
+				(((x) >> 2) & 0x3c000000)))
+
+#define CLPS711X_VIRT_BASE	IOMEM(IO_ADDRESS(CLPS711X_PHYS_BASE))
 
 #ifndef __ASSEMBLY__
 #define clps_readb(off)		readb(CLPS711X_VIRT_BASE + (off))
@@ -61,67 +64,17 @@
 #define CS7_PHYS_BASE		(0x00000000)
 #endif
 
-#define SYSPLD_VIRT_BASE	0xfe000000
-#define SYSPLD_BASE		SYSPLD_VIRT_BASE
-
-#if defined (CONFIG_ARCH_CDB89712)
-
-#define ETHER_START      0x20000000
-#define ETHER_SIZE       0x1000
-#define ETHER_BASE       0xfe000000
-
-#endif
+#define CLPS711X_SRAM_BASE	CS6_PHYS_BASE
+#define CLPS711X_SRAM_SIZE	(48 * 1024)
 
+#define CLPS711X_SDRAM0_BASE	(0xc0000000)
+#define CLPS711X_SDRAM1_BASE	(0xd0000000)
 
 #if defined (CONFIG_ARCH_EDB7211)
 
-/*
- * The extra 8 lines of the keyboard matrix are wired to chip select 3 (nCS3) 
- * and repeat across it. This is the mapping for it.
- *
- * In jumpered boot mode, nCS3 is mapped to 0x4000000, not 0x3000000. This 
- * was cause for much consternation and headscratching. This should probably
- * be made a compile/run time kernel option.
- */
-#define EP7211_PHYS_EXTKBD		CS3_PHYS_BASE	/* physical */
-
-#define EP7211_VIRT_EXTKBD		(0xfd000000)	/* virtual */
-
-
-/*
- * The CS8900A ethernet chip has its I/O registers wired to chip select 2 
- * (nCS2). This is the mapping for it.
- *
- * In jumpered boot mode, nCS2 is mapped to 0x5000000, not 0x2000000. This 
- * was cause for much consternation and headscratching. This should probably
- * be made a compile/run time kernel option.
- */
-#define EP7211_PHYS_CS8900A		CS2_PHYS_BASE	/* physical */
-
-#define EP7211_VIRT_CS8900A		(0xfc000000)	/* virtual */
-
-
-/*
- * The two flash banks are wired to chip selects 0 and 1. This is the mapping
- * for them.
- *
- * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
- * in jumpered boot mode.
- */
-#define EP7211_PHYS_FLASH1		CS0_PHYS_BASE	/* physical */
-#define EP7211_PHYS_FLASH2		CS1_PHYS_BASE	/* physical */
-
-#define EP7211_VIRT_FLASH1		(0xfa000000)	/* virtual */
-#define EP7211_VIRT_FLASH2		(0xfb000000)	/* virtual */
+/* The extra 8 lines of the keyboard matrix are wired to chip select 3 */
+#define EP7211_PHYS_EXTKBD	CS3_PHYS_BASE
 
 #endif /* CONFIG_ARCH_EDB7211 */
 
-/*
- * Relevant bits in port D, which controls power to the various parts of
- * the LCD on the EDB7211.
- */
-#define EDB_PD1_LCD_DC_DC_EN	(1<<1)
-#define EDB_PD2_LCDEN		(1<<2)
-#define EDB_PD3_LCDBL		(1<<3)
-
 #endif