1 files changed, 44 insertions, 49 deletions

diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index 3bf3408e94c..b64648b4a1f 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -8,6 +8,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -17,6 +18,7 @@
 #include <linux/clk.h>
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
+#include <linux/platform_data/at91_adc.h>
 
 #include <video/atmel_lcdc.h>
 
@@ -29,36 +31,23 @@
 #include <asm/mach/irq.h>
 
 #include <mach/hardware.h>
-#include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
-#include <mach/at91_shdwc.h>
 
+
+#include "at91_aic.h"
+#include "at91_shdwc.h"
+#include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
-static void __init ek_map_io(void)
+static void __init ek_init_early(void)
 {
 	/* Initialize processor: 12.000 MHz crystal */
-	at91sam9rl_initialize(12000000);
-
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
-}
-
-static void __init ek_init_irq(void)
-{
-	at91sam9rl_init_interrupts(NULL);
+	at91_initialize(12000000);
 }
 
-
 /*
  * USB HS Device port
  */
@@ -70,11 +59,12 @@ static struct usba_platform_data __initdata ek_usba_udc_data = {
 /*
  * MCI (SD/MMC)
  */
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PA15,
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PA15,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 
@@ -94,19 +84,16 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 	},
 };
 
-static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
-{
-	*num_partitions = ARRAY_SIZE(ek_nand_partition);
-	return ek_nand_partition;
-}
-
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PD17,
 	.enable_pin	= AT91_PIN_PB6,
-	.partition_info	= nand_partitions,
+	.ecc_mode	= NAND_ECC_SOFT,
+	.on_flash_bbt	= 1,
+	.parts		= ek_nand_partition,
+	.num_parts	= ARRAY_SIZE(ek_nand_partition),
 };
 
 static struct sam9_smc_config __initdata ek_nand_smc_config = {
@@ -130,7 +117,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 static void __init ek_add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -185,7 +172,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
 					| ATMEL_LCDC_DISTYPE_TFT \
 					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
 
-static void at91_lcdc_power_control(int on)
+static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
 {
 	if (on)
 		at91_set_gpio_value(AT91_PIN_PC1, 0);	/* power up */
@@ -194,7 +181,7 @@ static void at91_lcdc_power_control(int on)
 }
 
 /* Driver datas */
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
 	.lcdcon_is_backlight            = true,
 	.default_bpp			= 16,
 	.default_dmacon			= ATMEL_LCDC_DMAEN,
@@ -206,7 +193,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
 };
 
 #else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
 #endif
 
 
@@ -215,6 +202,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data;
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 
@@ -243,12 +231,13 @@ static struct gpio_led ek_leds[] = {
 
 
 /*
- * Touchscreen
+ * ADC + Touchscreen
  */
-static struct at91_tsadcc_data ek_tsadcc_data = {
-	.adc_clock		= 1000000,
-	.pendet_debounce	= 0x0f,
-	.ts_sample_hold_time	= 0x03,
+static struct at91_adc_data ek_adc_data = {
+	.channels_used = BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(5),
+	.use_external_triggers = true,
+	.vref = 3300,
+	.touchscreen_type = ATMEL_ADC_TOUCHSCREEN_4WIRE,
 };
 
 
@@ -304,6 +293,11 @@ static void __init ek_add_device_buttons(void) {}
 static void __init ek_board_init(void)
 {
 	/* Serial */
+	/* DBGU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
+	at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
 	at91_add_device_serial();
 	/* USB HS */
 	at91_add_device_usba(&ek_usba_udc_data);
@@ -314,13 +308,13 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* MMC */
-	at91_add_device_mmc(0, &ek_mmc_data);
+	at91_add_device_mci(0, &mci0_data);
 	/* LCD Controller */
 	at91_add_device_lcdc(&ek_lcdc_data);
 	/* AC97 */
 	at91_add_device_ac97(&ek_ac97_data);
-	/* Touch Screen Controller */
-	at91_add_device_tsadcc(&ek_tsadcc_data);
+	/* Touch Screen Controller + ADC */
+	at91_add_device_adc(&ek_adc_data);
 	/* LEDs */
 	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
 	/* Push Buttons */
@@ -329,9 +323,10 @@ static void __init ek_board_init(void)
 
 MACHINE_START(AT91SAM9RLEK, "Atmel AT91SAM9RL-EK")
 	/* Maintainer: Atmel */
-	.boot_params	= AT91_SDRAM_BASE + 0x100,
-	.timer		= &at91sam926x_timer,
-	.map_io		= ek_map_io,
-	.init_irq	= ek_init_irq,
+	.init_time	= at91sam926x_pit_init,
+	.map_io		= at91_map_io,
+	.handle_irq	= at91_aic_handle_irq,
+	.init_early	= ek_init_early,
+	.init_irq	= at91_init_irq_default,
 	.init_machine	= ek_board_init,
 MACHINE_END