diff options
Diffstat (limited to 'arch/arm/mach-at91/board-sam9260ek.c')
| -rw-r--r-- | arch/arm/mach-at91/board-sam9260ek.c | 210 |
1 files changed, 152 insertions, 58 deletions
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index 6a680795c3c..65dea12d685 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -20,6 +20,7 @@ */ #include <linux/types.h> +#include <linux/gpio.h> #include <linux/init.h> #include <linux/mm.h> #include <linux/module.h> @@ -27,8 +28,10 @@ #include <linux/spi/spi.h> #include <linux/spi/at73c213.h> #include <linux/clk.h> +#include <linux/platform_data/at24.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> -#include <asm/hardware.h> #include <asm/setup.h> #include <asm/mach-types.h> #include <asm/irq.h> @@ -37,43 +40,31 @@ #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include <asm/arch/board.h> -#include <asm/arch/gpio.h> +#include <mach/hardware.h> +#include <mach/at91sam9_smc.h> +#include <mach/system_rev.h> +#include "at91_aic.h" +#include "at91_shdwc.h" +#include "board.h" +#include "sam9_smc.h" #include "generic.h" +#include "gpio.h" -static void __init ek_map_io(void) +static void __init ek_init_early(void) { /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); -} - -static void __init ek_init_irq(void) -{ - at91sam9260_init_interrupts(NULL); + at91_initialize(18432000); } - /* * USB Host port */ static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -81,7 +72,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = { */ static struct at91_udc_data __initdata ek_udc_data = { .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; @@ -118,7 +109,7 @@ static void __init at73c213_set_clk(struct at73c213_board_info *info) {} * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !IS_ENABLED(CONFIG_MMC_ATMELMCI) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -150,7 +141,7 @@ static struct spi_board_info ek_spi_devices[] = { /* * MACB Ethernet device */ -static struct at91_eth_data __initdata ek_macb_data = { +static struct macb_platform_data __initdata ek_macb_data = { .phy_irq_pin = AT91_PIN_PA7, .is_rmii = 1, }; @@ -163,45 +154,70 @@ static struct mtd_partition __initdata ek_nand_partition[] = { { .name = "Partition 1", .offset = 0, - .size = 256 * 1024, + .size = SZ_256K, }, { .name = "Partition 2", - .offset = 256 * 1024, + .offset = MTDPART_OFS_NXTBLK, .size = MTDPART_SIZ_FULL, }, }; -static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) -{ - *num_partitions = ARRAY_SIZE(ek_nand_partition); - return ek_nand_partition; -} - static struct atmel_nand_data __initdata ek_nand_data = { .ale = 21, .cle = 22, -// .det_pin = ... not connected + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, - .partition_info = nand_partitions, -#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16) - .bus_width_16 = 1, -#else - .bus_width_16 = 0, -#endif + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, + .parts = ek_nand_partition, + .num_parts = ARRAY_SIZE(ek_nand_partition), }; +static struct sam9_smc_config __initdata ek_nand_smc_config = { + .ncs_read_setup = 0, + .nrd_setup = 1, + .ncs_write_setup = 0, + .nwe_setup = 1, + + .ncs_read_pulse = 3, + .nrd_pulse = 3, + .ncs_write_pulse = 3, + .nwe_pulse = 3, + + .read_cycle = 5, + .write_cycle = 5, + + .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE, + .tdf_cycles = 2, +}; + +static void __init ek_add_device_nand(void) +{ + ek_nand_data.bus_width_16 = board_have_nand_16bit(); + /* setup bus-width (8 or 16) */ + if (ek_nand_data.bus_width_16) + ek_nand_smc_config.mode |= AT91_SMC_DBW_16; + else + ek_nand_smc_config.mode |= AT91_SMC_DBW_8; + + /* configure chip-select 3 (NAND) */ + sam9_smc_configure(0, 3, &ek_nand_smc_config); + + at91_add_device_nand(&ek_nand_data); +} + /* * MCI (SD/MMC) */ -static struct at91_mmc_data __initdata ek_mmc_data = { - .slot_b = 1, - .wire4 = 1, -// .det_pin = ... not connected -// .wp_pin = ... not connected -// .vcc_pin = ... not connected +static struct mci_platform_data __initdata ek_mci0_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = -EINVAL, + .wp_pin = -EINVAL, + }, }; @@ -222,9 +238,86 @@ static struct gpio_led ek_leds[] = { } }; +/* + * I2C devices + */ +static struct at24_platform_data at24c512 = { + .byte_len = SZ_512K / 8, + .page_size = 128, + .flags = AT24_FLAG_ADDR16, +}; + +static struct i2c_board_info __initdata ek_i2c_devices[] = { + { + I2C_BOARD_INFO("24c512", 0x50), + .platform_data = &at24c512, + }, + /* more devices can be added using expansion connectors */ +}; + + +/* + * GPIO Buttons + */ +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +static struct gpio_keys_button ek_buttons[] = { + { + .gpio = AT91_PIN_PA30, + .code = BTN_3, + .desc = "Button 3", + .active_low = 1, + .wakeup = 1, + }, + { + .gpio = AT91_PIN_PA31, + .code = BTN_4, + .desc = "Button 4", + .active_low = 1, + .wakeup = 1, + } +}; + +static struct gpio_keys_platform_data ek_button_data = { + .buttons = ek_buttons, + .nbuttons = ARRAY_SIZE(ek_buttons), +}; + +static struct platform_device ek_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &ek_button_data, + } +}; + +static void __init ek_add_device_buttons(void) +{ + at91_set_gpio_input(AT91_PIN_PA30, 1); /* btn3 */ + at91_set_deglitch(AT91_PIN_PA30, 1); + at91_set_gpio_input(AT91_PIN_PA31, 1); /* btn4 */ + at91_set_deglitch(AT91_PIN_PA31, 1); + + platform_device_register(&ek_button_device); +} +#else +static void __init ek_add_device_buttons(void) {} +#endif + + static void __init ek_board_init(void) { /* Serial */ + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); at91_add_device_serial(); /* USB Host */ at91_add_device_usbh(&ek_usbh_data); @@ -233,27 +326,28 @@ static void __init ek_board_init(void) /* SPI */ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); /* NAND */ - at91_add_device_nand(&ek_nand_data); + ek_add_device_nand(); /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ - at91_add_device_mmc(0, &ek_mmc_data); + at91_add_device_mci(0, &ek_mci0_data); /* I2C */ - at91_add_device_i2c(NULL, 0); + at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); /* SSC (to AT73C213) */ at73c213_set_clk(&at73c213_data); at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX); /* LEDs */ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); + /* Push Buttons */ + ek_add_device_buttons(); } MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK") /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91sam926x_timer, - .map_io = ek_map_io, - .init_irq = ek_init_irq, + .init_time = at91sam926x_pit_init, + .map_io = at91_map_io, + .handle_irq = at91_aic_handle_irq, + .init_early = ek_init_early, + .init_irq = at91_init_irq_default, .init_machine = ek_board_init, MACHINE_END |