diff options
Diffstat (limited to 'arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts')
| -rw-r--r-- | arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts | 141 |
1 files changed, 122 insertions, 19 deletions
diff --git a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts index 5ed6c137690..89ff404a528 100644 --- a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts +++ b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts @@ -6,8 +6,19 @@ * warranty of any kind, whether express or implied. */ +/* + * TODO: add Orion USB device port init when kernel.org support is added. + * TODO: add flash write support: see below. + * TODO: add power-off support. + * TODO: add I2C EEPROM support. + */ + /dts-v1/; -/include/ "orion5x.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include "orion5x-mv88f5182.dtsi" / { model = "LaCie Ethernet Disk mini V2"; @@ -19,49 +30,84 @@ chosen { bootargs = "console=ttyS0,115200n8 earlyprintk"; + linux,stdout-path = &uart0; }; - ocp@f1000000 { - serial@12000 { - clock-frequency = <166666667>; - status = "okay"; - }; - - sata@80000 { - status = "okay"; - nr-ports = <2>; - }; + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>, + <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>, + <MBUS_ID(0x01, 0x0f) 0 0xfff80000 0x80000>; }; - gpio_keys { + gpio-keys { compatible = "gpio-keys"; + pinctrl-0 = <&pmx_power_button>; + pinctrl-names = "default"; #address-cells = <1>; #size-cells = <0>; button@1 { label = "Power-on Switch"; - linux,code = <116>; /* KEY_POWER */ - gpios = <&gpio0 18 0>; + linux,code = <KEY_POWER>; + gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; }; }; - gpio_leds { + gpio-leds { compatible = "gpio-leds"; + pinctrl-0 = <&pmx_power_led>; + pinctrl-names = "default"; led@1 { label = "power:blue"; - gpios = <&gpio0 16 1>; + gpios = <&gpio0 16 GPIO_ACTIVE_LOW>; }; }; }; -&mdio { +&devbus_bootcs { status = "okay"; - ethphy: ethernet-phy { - reg = <8>; + /* Read parameters */ + devbus,bus-width = <8>; + devbus,turn-off-ps = <90000>; + devbus,badr-skew-ps = <0>; + devbus,acc-first-ps = <186000>; + devbus,acc-next-ps = <186000>; + + /* Write parameters */ + devbus,wr-high-ps = <90000>; + devbus,wr-low-ps = <90000>; + devbus,ale-wr-ps = <90000>; + + /* + * Currently the MTD code does not recognize the MX29LV400CBCT + * as a bottom-type device. This could cause risks of + * accidentally erasing critical flash sectors. We thus define + * a single, write-protected partition covering the whole + * flash. TODO: once the flash part TOP/BOTTOM detection + * issue is sorted out in the MTD code, break this into at + * least three partitions: 'u-boot code', 'u-boot environment' + * and 'whatever is left'. + */ + flash@0 { + compatible = "cfi-flash"; + reg = <0 0x80000>; + bank-width = <1>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Full512Kb"; + reg = <0 0x80000>; + read-only; + }; }; }; +&ehci0 { + status = "okay"; +}; + ð { status = "okay"; @@ -69,3 +115,60 @@ phy-handle = <ðphy>; }; }; + +&i2c { + status = "okay"; + clock-frequency = <100000>; + #address-cells = <1>; + + rtc@32 { + compatible = "ricoh,rs5c372a"; + reg = <0x32>; + interrupt-parent = <&gpio0>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&mdio { + status = "okay"; + + ethphy: ethernet-phy { + reg = <8>; + }; +}; + +&pinctrl { + pinctrl-0 = <&pmx_rtc &pmx_power_led_ctrl>; + pinctrl-names = "default"; + + pmx_power_button: pmx-power-button { + marvell,pins = "mpp18"; + marvell,function = "gpio"; + }; + + pmx_power_led: pmx-power-led { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_power_led_ctrl: pmx-power-led-ctrl { + marvell,pins = "mpp17"; + marvell,function = "gpio"; + }; + + pmx_rtc: pmx-rtc { + marvell,pins = "mpp3"; + marvell,function = "gpio"; + }; +}; + +&sata { + pinctrl-0 = <&pmx_sata0 &pmx_sata1>; + pinctrl-names = "default"; + status = "okay"; + nr-ports = <2>; +}; + +&uart0 { + status = "okay"; +}; |