diff options
Diffstat (limited to 'arch/arm/boot/dts/omap5.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/omap5.dtsi | 264 |
1 files changed, 257 insertions, 7 deletions
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index fc3fad56386..a4ed5498886 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -45,10 +45,19 @@ operating-points = < /* kHz uV */ - 500000 880000 1000000 1060000 1500000 1250000 >; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ + + /* cooling options */ + cooling-min-level = <0>; + cooling-max-level = <2>; + #cooling-cells = <2>; /* min followed by max */ }; cpu@1 { device_type = "cpu"; @@ -57,6 +66,12 @@ }; }; + thermal-zones { + #include "omap4-cpu-thermal.dtsi" + #include "omap5-gpu-thermal.dtsi" + #include "omap5-core-thermal.dtsi" + }; + timer { compatible = "arm,armv7-timer"; /* PPI secure/nonsecure IRQ */ @@ -66,6 +81,12 @@ <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>; }; + pmu { + compatible = "arm,cortex-a15-pmu"; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>; + }; + gic: interrupt-controller@48211000 { compatible = "arm,cortex-a15-gic"; interrupt-controller; @@ -77,7 +98,7 @@ }; /* - * The soc node represents the soc top level view. It is uses for IPs + * The soc node represents the soc top level view. It is used for IPs * that are not memory mapped in the MPU view or for the MPU itself. */ soc { @@ -91,7 +112,7 @@ /* * XXX: Use a flat representation of the OMAP3 interconnect. * The real OMAP interconnect network is quite complex. - * Since that will not bring real advantage to represent that in DT for + * Since it will not bring real advantage to represent that in DT for * the moment, just use a fake OCP bus entry to represent the whole bus * hierarchy. */ @@ -107,6 +128,58 @@ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + prm: prm@4ae06000 { + compatible = "ti,omap5-prm"; + reg = <0x4ae06000 0x3000>; + + prm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prm_clockdomains: clockdomains { + }; + }; + + cm_core_aon: cm_core_aon@4a004000 { + compatible = "ti,omap5-cm-core-aon"; + reg = <0x4a004000 0x2000>; + + cm_core_aon_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + cm_core_aon_clockdomains: clockdomains { + }; + }; + + scrm: scrm@4ae0a000 { + compatible = "ti,omap5-scrm"; + reg = <0x4ae0a000 0x2000>; + + scrm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + scrm_clockdomains: clockdomains { + }; + }; + + cm_core: cm_core@4a008000 { + compatible = "ti,omap5-cm-core"; + reg = <0x4a008000 0x3000>; + + cm_core_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + cm_core_clockdomains: clockdomains { + }; + }; + counter32k: counter@4ae04000 { compatible = "ti,omap-counter32k"; reg = <0x4ae04000 0x40>; @@ -130,6 +203,22 @@ pinctrl-single,function-mask = <0x7fff>; }; + omap5_padconf_global: tisyscon@4a002da0 { + compatible = "syscon"; + reg = <0x4A002da0 0xec>; + }; + + pbias_regulator: pbias_regulator { + compatible = "ti,pbias-omap"; + reg = <0x60 0x4>; + syscon = <&omap5_padconf_global>; + pbias_mmc_reg: pbias_mmc_omap5 { + regulator-name = "pbias_mmc_omap5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + }; + sdma: dma-controller@4a056000 { compatible = "ti,omap4430-sdma"; reg = <0x4a056000 0x1000>; @@ -240,6 +329,8 @@ gpmc,num-cs = <8>; gpmc,num-waitpins = <4>; ti,hwmods = "gpmc"; + clocks = <&l3_iclk_div>; + clock-names = "fck"; }; i2c1: i2c@48070000 { @@ -291,6 +382,7 @@ compatible = "ti,omap4-hwspinlock"; reg = <0x4a0f6000 0x1000>; ti,hwmods = "spinlock"; + #hwlock-cells = <1>; }; mcspi1: spi@48098000 { @@ -409,6 +501,7 @@ ti,needs-special-reset; dmas = <&sdma 61>, <&sdma 62>; dma-names = "tx", "rx"; + pbias-supply = <&pbias_mmc_reg>; }; mmc2: mmc@480b4000 { @@ -451,6 +544,21 @@ dma-names = "tx", "rx"; }; + mmu_dsp: mmu@4a066000 { + compatible = "ti,omap4-iommu"; + reg = <0x4a066000 0x100>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu_dsp"; + }; + + mmu_ipu: mmu@55082000 { + compatible = "ti,omap4-iommu"; + reg = <0x55082000 0x100>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu_ipu"; + ti,iommu-bus-err-back; + }; + keypad: keypad@4ae1c000 { compatible = "ti,omap4-keypad"; reg = <0x4ae1c000 0x400>; @@ -467,6 +575,7 @@ dmas = <&sdma 65>, <&sdma 66>; dma-names = "up_link", "dn_link"; + status = "disabled"; }; dmic: dmic@4012e000 { @@ -478,6 +587,7 @@ ti,hwmods = "dmic"; dmas = <&sdma 67>; dma-names = "up_link"; + status = "disabled"; }; mcbsp1: mcbsp@40122000 { @@ -492,6 +602,7 @@ dmas = <&sdma 33>, <&sdma 34>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp2: mcbsp@40124000 { @@ -506,6 +617,7 @@ dmas = <&sdma 17>, <&sdma 18>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp3: mcbsp@40126000 { @@ -520,6 +632,14 @@ dmas = <&sdma 19>, <&sdma 20>; dma-names = "tx", "rx"; + status = "disabled"; + }; + + mailbox: mailbox@4a0f4000 { + compatible = "ti,omap4-mailbox"; + reg = <0x4a0f4000 0x200>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mailbox"; }; timer1: timer@4ae18000 { @@ -621,6 +741,13 @@ ti,hwmods = "wd_timer2"; }; + dmm@4e000000 { + compatible = "ti,omap5-dmm"; + reg = <0x4e000000 0x800>; + interrupts = <0 113 0x4>; + ti,hwmods = "dmm"; + }; + emif1: emif@4c000000 { compatible = "ti,emif-4d5"; ti,hwmods = "emif1"; @@ -670,7 +797,8 @@ compatible = "snps,dwc3"; reg = <0x4a030000 0x10000>; interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; - usb-phy = <&usb2_phy>, <&usb3_phy>; + phys = <&usb2_phy>, <&usb3_phy>; + phy-names = "usb2-phy", "usb3-phy"; dr_mode = "peripheral"; tx-fifo-resize; }; @@ -687,6 +815,9 @@ compatible = "ti,omap-usb2"; reg = <0x4a084000 0x7c>; ctrl-module = <&omap_control_usb2phy>; + clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>; + clock-names = "wkupclk", "refclk"; + #phy-cells = <0>; }; usb3_phy: usb3phy@4a084400 { @@ -696,6 +827,13 @@ <0x4a084c00 0x40>; reg-names = "phy_rx", "phy_tx", "pll_ctrl"; ctrl-module = <&omap_control_usb3phy>; + clocks = <&usb_phy_cm_clk32k>, + <&sys_clkin>, + <&usb_otg_ss_refclk960m>; + clock-names = "wkupclk", + "sysclk", + "refclk"; + #phy-cells = <0>; }; }; @@ -713,29 +851,141 @@ #address-cells = <1>; #size-cells = <1>; ranges; + clocks = <&l3init_60m_fclk>, + <&xclk60mhsp1_ck>, + <&xclk60mhsp2_ck>; + clock-names = "refclk_60m_int", + "refclk_60m_ext_p1", + "refclk_60m_ext_p2"; usbhsohci: ohci@4a064800 { - compatible = "ti,ohci-omap3", "usb-ohci"; + compatible = "ti,ohci-omap3"; reg = <0x4a064800 0x400>; interrupt-parent = <&gic>; interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; }; usbhsehci: ehci@4a064c00 { - compatible = "ti,ehci-omap", "usb-ehci"; + compatible = "ti,ehci-omap"; reg = <0x4a064c00 0x400>; interrupt-parent = <&gic>; interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; }; }; - bandgap@4a0021e0 { + bandgap: bandgap@4a0021e0 { reg = <0x4a0021e0 0xc 0x4a00232c 0xc 0x4a002380 0x2c 0x4a0023C0 0x3c>; interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; compatible = "ti,omap5430-bandgap"; + + #thermal-sensor-cells = <1>; + }; + + omap_control_sata: control-phy@4a002374 { + compatible = "ti,control-phy-pipe3"; + reg = <0x4a002374 0x4>; + reg-names = "power"; + clocks = <&sys_clkin>; + clock-names = "sysclk"; + }; + + /* OCP2SCP3 */ + ocp2scp@4a090000 { + compatible = "ti,omap-ocp2scp"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x4a090000 0x20>; + ranges; + ti,hwmods = "ocp2scp3"; + sata_phy: phy@4a096000 { + compatible = "ti,phy-pipe3-sata"; + reg = <0x4A096000 0x80>, /* phy_rx */ + <0x4A096400 0x64>, /* phy_tx */ + <0x4A096800 0x40>; /* pll_ctrl */ + reg-names = "phy_rx", "phy_tx", "pll_ctrl"; + ctrl-module = <&omap_control_sata>; + clocks = <&sys_clkin>; + clock-names = "sysclk"; + #phy-cells = <0>; + }; + }; + + sata: sata@4a141100 { + compatible = "snps,dwc-ahci"; + reg = <0x4a140000 0x1100>, <0x4a141100 0x7>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; + phys = <&sata_phy>; + phy-names = "sata-phy"; + clocks = <&sata_ref_clk>; + ti,hwmods = "sata"; + }; + + dss: dss@58000000 { + compatible = "ti,omap5-dss"; + reg = <0x58000000 0x80>; + status = "disabled"; + ti,hwmods = "dss_core"; + clocks = <&dss_dss_clk>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dispc@58001000 { + compatible = "ti,omap5-dispc"; + reg = <0x58001000 0x1000>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "dss_dispc"; + clocks = <&dss_dss_clk>; + clock-names = "fck"; + }; + + dsi1: encoder@58004000 { + compatible = "ti,omap5-dsi"; + reg = <0x58004000 0x200>, + <0x58004200 0x40>, + <0x58004300 0x40>; + reg-names = "proto", "phy", "pll"; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + ti,hwmods = "dss_dsi1"; + clocks = <&dss_dss_clk>, <&dss_sys_clk>; + clock-names = "fck", "sys_clk"; + }; + + dsi2: encoder@58005000 { + compatible = "ti,omap5-dsi"; + reg = <0x58009000 0x200>, + <0x58009200 0x40>, + <0x58009300 0x40>; + reg-names = "proto", "phy", "pll"; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + ti,hwmods = "dss_dsi2"; + clocks = <&dss_dss_clk>, <&dss_sys_clk>; + clock-names = "fck", "sys_clk"; + }; + + hdmi: encoder@58060000 { + compatible = "ti,omap5-hdmi"; + reg = <0x58040000 0x200>, + <0x58040200 0x80>, + <0x58040300 0x80>, + <0x58060000 0x19000>; + reg-names = "wp", "pll", "phy", "core"; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + ti,hwmods = "dss_hdmi"; + clocks = <&dss_48mhz_clk>, <&dss_sys_clk>; + clock-names = "fck", "sys_clk"; + dmas = <&sdma 76>; + dma-names = "audio_tx"; + }; }; }; }; + +/include/ "omap54xx-clocks.dtsi" |