diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/DocBook/genericirq.tmpl | 84 | ||||
| -rw-r--r-- | Documentation/DocBook/kernel-locking.tmpl | 14 | ||||
| -rw-r--r-- | Documentation/RCU/checklist.txt | 46 | ||||
| -rw-r--r-- | Documentation/RCU/stallwarn.txt | 18 | ||||
| -rw-r--r-- | Documentation/RCU/trace.txt | 13 | ||||
| -rw-r--r-- | Documentation/cputopology.txt | 23 | ||||
| -rw-r--r-- | Documentation/feature-removal-schedule.txt | 28 | ||||
| -rw-r--r-- | Documentation/kernel-parameters.txt | 11 | ||||
| -rw-r--r-- | Documentation/kprobes.txt | 8 | ||||
| -rw-r--r-- | Documentation/networking/e1000.txt | 373 | ||||
| -rw-r--r-- | Documentation/networking/e1000e.txt | 302 | ||||
| -rw-r--r--[-rwxr-xr-x] | Documentation/networking/ixgbevf.txt | 40 | ||||
| -rw-r--r-- | Documentation/vm/page-types.c | 2 |
13 files changed, 562 insertions, 400 deletions
diff --git a/Documentation/DocBook/genericirq.tmpl b/Documentation/DocBook/genericirq.tmpl index 1448b33fd22..fb10fd08c05 100644 --- a/Documentation/DocBook/genericirq.tmpl +++ b/Documentation/DocBook/genericirq.tmpl @@ -28,7 +28,7 @@ </authorgroup> <copyright> - <year>2005-2006</year> + <year>2005-2010</year> <holder>Thomas Gleixner</holder> </copyright> <copyright> @@ -100,6 +100,10 @@ <listitem><para>Edge type</para></listitem> <listitem><para>Simple type</para></listitem> </itemizedlist> + During the implementation we identified another type: + <itemizedlist> + <listitem><para>Fast EOI type</para></listitem> + </itemizedlist> In the SMP world of the __do_IRQ() super-handler another type was identified: <itemizedlist> @@ -153,6 +157,7 @@ is still available. This leads to a kind of duality for the time being. Over time the new model should be used in more and more architectures, as it enables smaller and cleaner IRQ subsystems. + It's deprecated for three years now and about to be removed. </para> </chapter> <chapter id="bugs"> @@ -217,6 +222,7 @@ <itemizedlist> <listitem><para>handle_level_irq</para></listitem> <listitem><para>handle_edge_irq</para></listitem> + <listitem><para>handle_fasteoi_irq</para></listitem> <listitem><para>handle_simple_irq</para></listitem> <listitem><para>handle_percpu_irq</para></listitem> </itemizedlist> @@ -233,33 +239,33 @@ are used by the default flow implementations. The following helper functions are implemented (simplified excerpt): <programlisting> -default_enable(irq) +default_enable(struct irq_data *data) { - desc->chip->unmask(irq); + desc->chip->irq_unmask(data); } -default_disable(irq) +default_disable(struct irq_data *data) { - if (!delay_disable(irq)) - desc->chip->mask(irq); + if (!delay_disable(data)) + desc->chip->irq_mask(data); } -default_ack(irq) +default_ack(struct irq_data *data) { - chip->ack(irq); + chip->irq_ack(data); } -default_mask_ack(irq) +default_mask_ack(struct irq_data *data) { - if (chip->mask_ack) { - chip->mask_ack(irq); + if (chip->irq_mask_ack) { + chip->irq_mask_ack(data); } else { - chip->mask(irq); - chip->ack(irq); + chip->irq_mask(data); + chip->irq_ack(data); } } -noop(irq) +noop(struct irq_data *data)) { } @@ -278,12 +284,27 @@ noop(irq) <para> The following control flow is implemented (simplified excerpt): <programlisting> -desc->chip->start(); +desc->chip->irq_mask(); handle_IRQ_event(desc->action); -desc->chip->end(); +desc->chip->irq_unmask(); </programlisting> </para> - </sect3> + </sect3> + <sect3 id="Default_FASTEOI_IRQ_flow_handler"> + <title>Default Fast EOI IRQ flow handler</title> + <para> + handle_fasteoi_irq provides a generic implementation + for interrupts, which only need an EOI at the end of + the handler + </para> + <para> + The following control flow is implemented (simplified excerpt): + <programlisting> +handle_IRQ_event(desc->action); +desc->chip->irq_eoi(); + </programlisting> + </para> + </sect3> <sect3 id="Default_Edge_IRQ_flow_handler"> <title>Default Edge IRQ flow handler</title> <para> @@ -294,20 +315,19 @@ desc->chip->end(); The following control flow is implemented (simplified excerpt): <programlisting> if (desc->status & running) { - desc->chip->hold(); + desc->chip->irq_mask(); desc->status |= pending | masked; return; } -desc->chip->start(); +desc->chip->irq_ack(); desc->status |= running; do { if (desc->status & masked) - desc->chip->enable(); + desc->chip->irq_unmask(); desc->status &= ~pending; handle_IRQ_event(desc->action); } while (status & pending); desc->status &= ~running; -desc->chip->end(); </programlisting> </para> </sect3> @@ -342,9 +362,9 @@ handle_IRQ_event(desc->action); <para> The following control flow is implemented (simplified excerpt): <programlisting> -desc->chip->start(); handle_IRQ_event(desc->action); -desc->chip->end(); +if (desc->chip->irq_eoi) + desc->chip->irq_eoi(); </programlisting> </para> </sect3> @@ -375,8 +395,7 @@ desc->chip->end(); mechanism. (It's necessary to enable CONFIG_HARDIRQS_SW_RESEND when you want to use the delayed interrupt disable feature and your hardware is not capable of retriggering an interrupt.) - The delayed interrupt disable can be runtime enabled, per interrupt, - by setting the IRQ_DELAYED_DISABLE flag in the irq_desc status field. + The delayed interrupt disable is not configurable. </para> </sect2> </sect1> @@ -387,13 +406,13 @@ desc->chip->end(); contains all the direct chip relevant functions, which can be utilized by the irq flow implementations. <itemizedlist> - <listitem><para>ack()</para></listitem> - <listitem><para>mask_ack() - Optional, recommended for performance</para></listitem> - <listitem><para>mask()</para></listitem> - <listitem><para>unmask()</para></listitem> - <listitem><para>retrigger() - Optional</para></listitem> - <listitem><para>set_type() - Optional</para></listitem> - <listitem><para>set_wake() - Optional</para></listitem> + <listitem><para>irq_ack()</para></listitem> + <listitem><para>irq_mask_ack() - Optional, recommended for performance</para></listitem> + <listitem><para>irq_mask()</para></listitem> + <listitem><para>irq_unmask()</para></listitem> + <listitem><para>irq_retrigger() - Optional</para></listitem> + <listitem><para>irq_set_type() - Optional</para></listitem> + <listitem><para>irq_set_wake() - Optional</para></listitem> </itemizedlist> These primitives are strictly intended to mean what they say: ack means ACK, masking means masking of an IRQ line, etc. It is up to the flow @@ -458,6 +477,7 @@ desc->chip->end(); <para> This chapter contains the autogenerated documentation of the internal functions. </para> +!Ikernel/irq/irqdesc.c !Ikernel/irq/handle.c !Ikernel/irq/chip.c </chapter> diff --git a/Documentation/DocBook/kernel-locking.tmpl b/Documentation/DocBook/kernel-locking.tmpl index a0d479d1e1d..f66f4df1869 100644 --- a/Documentation/DocBook/kernel-locking.tmpl +++ b/Documentation/DocBook/kernel-locking.tmpl @@ -1645,7 +1645,9 @@ the amount of locking which needs to be done. all the readers who were traversing the list when we deleted the element are finished. We use <function>call_rcu()</function> to register a callback which will actually destroy the object once - the readers are finished. + all pre-existing readers are finished. Alternatively, + <function>synchronize_rcu()</function> may be used to block until + all pre-existing are finished. </para> <para> But how does Read Copy Update know when the readers are @@ -1714,7 +1716,7 @@ the amount of locking which needs to be done. - object_put(obj); + list_del_rcu(&obj->list); cache_num--; -+ call_rcu(&obj->rcu, cache_delete_rcu, obj); ++ call_rcu(&obj->rcu, cache_delete_rcu); } /* Must be holding cache_lock */ @@ -1725,14 +1727,6 @@ the amount of locking which needs to be done. if (++cache_num > MAX_CACHE_SIZE) { struct object *i, *outcast = NULL; list_for_each_entry(i, &cache, list) { -@@ -85,6 +94,7 @@ - obj->popularity = 0; - atomic_set(&obj->refcnt, 1); /* The cache holds a reference */ - spin_lock_init(&obj->lock); -+ INIT_RCU_HEAD(&obj->rcu); - - spin_lock_irqsave(&cache_lock, flags); - __cache_add(obj); @@ -104,12 +114,11 @@ struct object *cache_find(int id) { diff --git a/Documentation/RCU/checklist.txt b/Documentation/RCU/checklist.txt index 790d1a81237..0c134f8afc6 100644 --- a/Documentation/RCU/checklist.txt +++ b/Documentation/RCU/checklist.txt @@ -218,13 +218,22 @@ over a rather long period of time, but improvements are always welcome! include: a. Keeping a count of the number of data-structure elements - used by the RCU-protected data structure, including those - waiting for a grace period to elapse. Enforce a limit - on this number, stalling updates as needed to allow - previously deferred frees to complete. - - Alternatively, limit only the number awaiting deferred - free rather than the total number of elements. + used by the RCU-protected data structure, including + those waiting for a grace period to elapse. Enforce a + limit on this number, stalling updates as needed to allow + previously deferred frees to complete. Alternatively, + limit only the number awaiting deferred free rather than + the total number of elements. + + One way to stall the updates is to acquire the update-side + mutex. (Don't try this with a spinlock -- other CPUs + spinning on the lock could prevent the grace period + from ever ending.) Another way to stall the updates + is for the updates to use a wrapper function around + the memory allocator, so that this wrapper function + simulates OOM when there is too much memory awaiting an + RCU grace period. There are of course many other + variations on this theme. b. Limiting update rate. For example, if updates occur only once per hour, then no explicit rate limiting is required, @@ -365,3 +374,26 @@ over a rather long period of time, but improvements are always welcome! and the compiler to freely reorder code into and out of RCU read-side critical sections. It is the responsibility of the RCU update-side primitives to deal with this. + +17. Use CONFIG_PROVE_RCU, CONFIG_DEBUG_OBJECTS_RCU_HEAD, and + the __rcu sparse checks to validate your RCU code. These + can help find problems as follows: + + CONFIG_PROVE_RCU: check that accesses to RCU-protected data + structures are carried out under the proper RCU + read-side critical section, while holding the right + combination of locks, or whatever other conditions + are appropriate. + + CONFIG_DEBUG_OBJECTS_RCU_HEAD: check that you don't pass the + same object to call_rcu() (or friends) before an RCU + grace period has elapsed since the last time that you + passed that same object to call_rcu() (or friends). + + __rcu sparse checks: tag the pointer to the RCU-protected data + structure with __rcu, and sparse will warn you if you + access that pointer without the services of one of the + variants of rcu_dereference(). + + These debugging aids can help you find problems that are + otherwise extremely difficult to spot. diff --git a/Documentation/RCU/stallwarn.txt b/Documentation/RCU/stallwarn.txt index 44c6dcc93d6..862c08ef1fd 100644 --- a/Documentation/RCU/stallwarn.txt +++ b/Documentation/RCU/stallwarn.txt @@ -80,6 +80,24 @@ o A CPU looping with bottom halves disabled. This condition can o For !CONFIG_PREEMPT kernels, a CPU looping anywhere in the kernel without invoking schedule(). +o A CPU-bound real-time task in a CONFIG_PREEMPT kernel, which might + happen to preempt a low-priority task in the middle of an RCU + read-side critical section. This is especially damaging if + that low-priority task is not permitted to run on any other CPU, + in which case the next RCU grace period can never complete, which + will eventually cause the system to run out of memory and hang. + While the system is in the process of running itself out of + memory, you might see stall-warning messages. + +o A CPU-bound real-time task in a CONFIG_PREEMPT_RT kernel that + is running at a higher priority than the RCU softirq threads. + This will prevent RCU callbacks from ever being invoked, + and in a CONFIG_TREE_PREEMPT_RCU kernel will further prevent + RCU grace periods from ever completing. Either way, the + system will eventually run out of memory and hang. In the + CONFIG_TREE_PREEMPT_RCU case, you might see stall-warning + messages. + o A bug in the RCU implementation. o A hardware failure. This is quite unlikely, but has occurred diff --git a/Documentation/RCU/trace.txt b/Documentation/RCU/trace.txt index efd8cc95c06..a851118775d 100644 --- a/Documentation/RCU/trace.txt +++ b/Documentation/RCU/trace.txt @@ -125,6 +125,17 @@ o "b" is the batch limit for this CPU. If more than this number of RCU callbacks is ready to invoke, then the remainder will be deferred. +o "ci" is the number of RCU callbacks that have been invoked for + this CPU. Note that ci+ql is the number of callbacks that have + been registered in absence of CPU-hotplug activity. + +o "co" is the number of RCU callbacks that have been orphaned due to + this CPU going offline. + +o "ca" is the number of RCU callbacks that have been adopted due to + other CPUs going offline. Note that ci+co-ca+ql is the number of + RCU callbacks registered on this CPU. + There is also an rcu/rcudata.csv file with the same information in comma-separated-variable spreadsheet format. @@ -180,7 +191,7 @@ o "s" is the "signaled" state that drives force_quiescent_state()'s o "jfq" is the number of jiffies remaining for this grace period before force_quiescent_state() is invoked to help push things - along. Note that CPUs in dyntick-idle mode thoughout the grace + along. Note that CPUs in dyntick-idle mode throughout the grace period will not report on their own, but rather must be check by some other CPU via force_quiescent_state(). diff --git a/Documentation/cputopology.txt b/Documentation/cputopology.txt index f1c5c4bccd3..902d3151f52 100644 --- a/Documentation/cputopology.txt +++ b/Documentation/cputopology.txt @@ -14,25 +14,39 @@ to /proc/cpuinfo. identifier (rather than the kernel's). The actual value is architecture and platform dependent. -3) /sys/devices/system/cpu/cpuX/topology/thread_siblings: +3) /sys/devices/system/cpu/cpuX/topology/book_id: + + the book ID of cpuX. Typically it is the hardware platform's + identifier (rather than the kernel's). The actual value is + architecture and platform dependent. + +4) /sys/devices/system/cpu/cpuX/topology/thread_siblings: internel kernel map of cpuX's hardware threads within the same core as cpuX -4) /sys/devices/system/cpu/cpuX/topology/core_siblings: +5) /sys/devices/system/cpu/cpuX/topology/core_siblings: internal kernel map of cpuX's hardware threads within the same physical_package_id. +6) /sys/devices/system/cpu/cpuX/topology/book_siblings: + + internal kernel map of cpuX's hardware threads within the same + book_id. + To implement it in an architecture-neutral way, a new source file, -drivers/base/topology.c, is to export the 4 attributes. +drivers/base/topology.c, is to export the 4 or 6 attributes. The two book +related sysfs files will only be created if CONFIG_SCHED_BOOK is selected. For an architecture to support this feature, it must define some of these macros in include/asm-XXX/topology.h: #define topology_physical_package_id(cpu) #define topology_core_id(cpu) +#define topology_book_id(cpu) #define topology_thread_cpumask(cpu) #define topology_core_cpumask(cpu) +#define topology_book_cpumask(cpu) The type of **_id is int. The type of siblings is (const) struct cpumask *. @@ -45,6 +59,9 @@ not defined by include/asm-XXX/topology.h: 3) thread_siblings: just the given CPU 4) core_siblings: just the given CPU +For architectures that don't support books (CONFIG_SCHED_BOOK) there are no +default definitions for topology_book_id() and topology_book_cpumask(). + Additionally, CPU topology information is provided under /sys/devices/system/cpu and includes these files. The internal source for the output is in brackets ("[]"). diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 842aa9de84a..5e2bc4ab897 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -386,34 +386,6 @@ Who: Tejun Heo <tj@kernel.org> ---------------------------- -What: Support for VMware's guest paravirtuliazation technique [VMI] will be - dropped. -When: 2.6.37 or earlier. -Why: With the recent innovations in CPU hardware acceleration technologies - from Intel and AMD, VMware ran a few experiments to compare these - techniques to guest paravirtualization technique on VMware's platform. - These hardware assisted virtualization techniques have outperformed the - performance benefits provided by VMI in most of the workloads. VMware - expects that these hardware features will be ubiquitous in a couple of - years, as a result, VMware has started a phased retirement of this - feature from the hypervisor. We will be removing this feature from the - Kernel too. Right now we are targeting 2.6.37 but can retire earlier if - technical reasons (read opportunity to remove major chunk of pvops) - arise. - - Please note that VMI has always been an optimization and non-VMI kernels - still work fine on VMware's platform. - Latest versions of VMware's product which support VMI are, - Workstation 7.0 and VSphere 4.0 on ESX side, future maintainence - releases for these products will continue supporting VMI. - - For more details about VMI retirement take a look at this, - http://blogs.vmware.com/guestosguide/2009/09/vmi-retirement.html - -Who: Alok N Kataria <akataria@vmware.com> - ----------------------------- - What: Support for lcd_switch and display_get in asus-laptop driver When: March 2010 Why: These two features use non-standard interfaces. There are the diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 8dd7248508a..3a0009e03d1 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -455,7 +455,7 @@ and is between 256 and 4096 characters. It is defined in the file [ARM] imx_timer1,OSTS,netx_timer,mpu_timer2, pxa_timer,timer3,32k_counter,timer0_1 [AVR32] avr32 - [X86-32] pit,hpet,tsc,vmi-timer; + [X86-32] pit,hpet,tsc; scx200_hrt on Geode; cyclone on IBM x440 [MIPS] MIPS [PARISC] cr16 @@ -2153,6 +2153,11 @@ and is between 256 and 4096 characters. It is defined in the file Reserves a hole at the top of the kernel virtual address space. + reservelow= [X86] + Format: nn[K] + Set the amount of memory to reserve for BIOS at + the bottom of the address space. + reset_devices [KNL] Force drivers to reset the underlying device during initialization. @@ -2435,6 +2440,10 @@ and is between 256 and 4096 characters. It is defined in the file disables clocksource verification at runtime. Used to enable high-resolution timer mode on older hardware, and in virtualized environment. + [x86] noirqtime: Do not use TSC to do irq accounting. + Used to run time disable IRQ_TIME_ACCOUNTING on any + platforms where RDTSC is slow and this accounting + can add overhead. turbografx.map[2|3]= [HW,JOY] TurboGraFX parallel port interface diff --git a/Documentation/kprobes.txt b/Documentation/kprobes.txt index 1762b81fcdf..741fe66d6ec 100644 --- a/Documentation/kprobes.txt +++ b/Documentation/kprobes.txt @@ -542,9 +542,11 @@ Kprobes does not use mutexes or allocate memory except during registration and unregistration. Probe handlers are run with preemption disabled. Depending on the -architecture, handlers may also run with interrupts disabled. In any -case, your handler should not yield the CPU (e.g., by attempting to -acquire a semaphore). +architecture and optimization state, handlers may also run with +interrupts disabled (e.g., kretprobe handlers and optimized kprobe +handlers run without interrupt disabled on x86/x86-64). In any case, +your handler should not yield the CPU (e.g., by attempting to acquire +a semaphore). Since a return probe is implemented by replacing the return address with the trampoline's address, stack backtraces and calls diff --git a/Documentation/networking/e1000.txt b/Documentation/networking/e1000.txt index 2df71861e57..d9271e74e48 100644 --- a/Documentation/networking/e1000.txt +++ b/Documentation/networking/e1000.txt @@ -1,82 +1,35 @@ Linux* Base Driver for the Intel(R) PRO/1000 Family of Adapters =============================================================== -September 26, 2006 - +Intel Gigabit Linux driver. +Copyright(c) 1999 - 2010 Intel Corporation. Contents ======== -- In This Release - Identifying Your Adapter -- Building and Installation - Command Line Parameters - Speed and Duplex Configuration - Additional Configurations -- Known Issues - Support - -In This Release -=============== - -This file describes the Linux* Base Driver for the Intel(R) PRO/1000 Family -of Adapters. This driver includes support for Itanium(R)2-based systems. - -For questions related to hardware requirements, refer to the documentation -supplied with your Intel PRO/1000 adapter. All hardware requirements listed -apply to use with Linux. - -The following features are now available in supported kernels: - - Native VLANs - - Channel Bonding (teaming) - - SNMP - -Channel Bonding documentation can be found in the Linux kernel source: -/Documentation/networking/bonding.txt - -The driver information previously displayed in the /proc filesystem is not -supported in this release. Alternatively, you can use ethtool (version 1.6 -or later), lspci, and ifconfig to obtain the same information. - -Instructions on updating ethtool can be found in the section "Additional -Configurations" later in this document. - -NOTE: The Intel(R) 82562v 10/100 Network Connection only provides 10/100 -support. - - Identifying Your Adapter ======================== For more information on how to identify your adapter, go to the Adapter & Driver ID Guide at: - http://support.intel.com/support/network/adapter/pro100/21397.htm + http://support.intel.com/support/go/network/adapter/idguide.htm For the latest Intel network drivers for Linux, refer to the following website. In the search field, enter your adapter name or type, or use the networking link on the left to search for your adapter: - http://downloadfinder.intel.com/scripts-df/support_intel.asp - + http://support.intel.com/support/go/network/adapter/home.htm Command Line Parameters ======================= -If the driver is built as a module, the following optional parameters -are used by entering them on the command line with the modprobe command -using this syntax: - - modprobe e1000 [<option>=<VAL1>,<VAL2>,...] - -For example, with two PRO/1000 PCI adapters, entering: - - modprobe e1000 TxDescriptors=80,128 - -loads the e1000 driver with 80 TX descriptors for the first adapter and -128 TX descriptors for the second adapter. - The default value for each parameter is generally the recommended setting, unless otherwise noted. @@ -89,10 +42,6 @@ NOTES: For more information about the AutoNeg, Duplex, and Speed parameters, see the application note at: http://www.intel.com/design/network/applnots/ap450.htm - A descriptor describes a data buffer and attributes related to - the data buffer. This information is accessed by the hardware. - - AutoNeg ------- (Supported only on adapters with copper connections) @@ -106,7 +55,6 @@ Duplex parameters must not be specified. NOTE: Refer to the Speed and Duplex section of this readme for more information on the AutoNeg parameter. - Duplex ------ (Supported only on adapters with copper connections) @@ -119,7 +67,6 @@ set to auto-negotiate, the board auto-detects the correct duplex. If the link partner is forced (either full or half), Duplex defaults to half- duplex. - FlowControl ----------- Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx) @@ -128,16 +75,16 @@ Default Value: Reads flow control settings from the EEPROM This parameter controls the automatic generation(Tx) and response(Rx) to Ethernet PAUSE frames. - InterruptThrottleRate --------------------- (not supported on Intel(R) 82542, 82543 or 82544-based adapters) -Valid Range: 0,1,3,100-100000 (0=off, 1=dynamic, 3=dynamic conservative) +Valid Range: 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative, + 4=simplified balancing) Default Value: 3 The driver can limit the amount of interrupts per second that the adapter -will generate for incoming packets. It does this by writing a value to the -adapter that is based on the maximum amount of interrupts that the adapter +will generate for incoming packets. It does this by writing a value to the +adapter that is based on the maximum amount of interrupts that the adapter will generate per second. Setting InterruptThrottleRate to a value greater or equal to 100 @@ -146,37 +93,43 @@ per second, even if more packets have come in. This reduces interrupt load on the system and can lower CPU utilization under heavy load, but will increase latency as packets are not processed as quickly. -The default behaviour of the driver previously assumed a static -InterruptThrottleRate value of 8000, providing a good fallback value for -all traffic types,but lacking in small packet performance and latency. -The hardware can handle many more small packets per second however, and +The default behaviour of the driver previously assumed a static +InterruptThrottleRate value of 8000, providing a good fallback value for +all traffic types,but lacking in small packet performance and latency. +The hardware can handle many more small packets per second however, and for this reason an adaptive interrupt moderation algorithm was implemented. Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in which -it dynamically adjusts the InterruptThrottleRate value based on the traffic +it dynamically adjusts the InterruptThrottleRate value based on the traffic that it receives. After determining the type of incoming traffic in the last -timeframe, it will adjust the InterruptThrottleRate to an appropriate value +timeframe, it will adjust the InterruptThrottleRate to an appropriate value for that traffic. The algorithm classifies the incoming traffic every interval into -classes. Once the class is determined, the InterruptThrottleRate value is -adjusted to suit that traffic type the best. There are three classes defined: +classes. Once the class is determined, the InterruptThrottleRate value is +adjusted to suit that traffic type the best. There are three classes defined: "Bulk traffic", for large amounts of packets of normal size; "Low latency", for small amounts of traffic and/or a significant percentage of small -packets; and "Lowest latency", for almost completely small packets or +packets; and "Lowest latency", for almost completely small packets or minimal traffic. -In dynamic conservative mode, the InterruptThrottleRate value is set to 4000 -for traffic that falls in class "Bulk traffic". If traffic falls in the "Low -latency" or "Lowest latency" class, the InterruptThrottleRate is increased +In dynamic conservative mode, the InterruptThrottleRate value is set to 4000 +for traffic that falls in class "Bulk traffic". If traffic falls in the "Low +latency" or "Lowest latency" class, the InterruptThrottleRate is increased stepwise to 20000. This default mode is suitable for most applications. For situations where low latency is vital such as cluster or grid computing, the algorithm can reduce latency even more when InterruptThrottleRate is set to mode 1. In this mode, which operates -the same as mode 3, the InterruptThrottleRate will be increased stepwise to +the same as mode 3, the InterruptThrottleRate will be increased stepwise to 70000 for traffic in class "Lowest latency". +In simplified mode the interrupt rate is based on the ratio of Tx and +Rx traffic. If the bytes per second rate is approximately equal, the +interrupt rate will drop as low as 2000 interrupts per second. If the +traffic is mostly transmit or mostly receive, the interrupt rate could +be as high as 8000. + Setting InterruptThrottleRate to 0 turns off any interrupt moderation and may improve small packet latency, but is generally not suitable for bulk throughput traffic. @@ -212,8 +165,6 @@ NOTE: When e1000 is loaded with default settings and multiple adapters be platform-specific. If CPU utilization is not a concern, use RX_POLLING (NAPI) and default driver settings. - - RxDescriptors ------------- Valid Range: 80-256 for 82542 and 82543-based adapters @@ -225,15 +176,14 @@ by the driver. Increasing this value allows the driver to buffer more incoming packets, at the expense of increased system memory utilization. Each descriptor is 16 bytes. A receive buffer is also allocated for each -descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending +descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending on the MTU setting. The maximum MTU size is 16110. -NOTE: MTU designates the frame size. It only needs to be set for Jumbo - Frames. Depending on the available system resources, the request - for a higher number of receive descriptors may be denied. In this +NOTE: MTU designates the frame size. It only needs to be set for Jumbo + Frames. Depending on the available system resources, the request + for a higher number of receive descriptors may be denied. In this case, use a lower number. - RxIntDelay ---------- Valid Range: 0-65535 (0=off) @@ -254,7 +204,6 @@ CAUTION: When setting RxIntDelay to a value other than 0, adapters may restoring the network connection. To eliminate the potential for the hang ensure that RxIntDelay is set to 0. - RxAbsIntDelay ------------- (This parameter is supported only on 82540, 82545 and later adapters.) @@ -268,7 +217,6 @@ packet is received within the set amount of time. Proper tuning, along with RxIntDelay, may improve traffic throughput in specific network conditions. - Speed ----- (This parameter is supported only on adapters with copper connections.) @@ -280,7 +228,6 @@ Speed forces the line speed to the specified value in megabits per second partner is set to auto-negotiate, the board will auto-detect the correct speed. Duplex should also be set when Speed is set to either 10 or 100. - TxDescriptors ------------- Valid Range: 80-256 for 82542 and 82543-based adapters @@ -295,6 +242,36 @@ NOTE: Depending on the available system resources, the request for a higher number of transmit descriptors may be denied. In this case, use a lower number. +TxDescriptorStep +---------------- +Valid Range: 1 (use every Tx Descriptor) + 4 (use every 4th Tx Descriptor) + +Default Value: 1 (use every Tx Descriptor) + +On certain non-Intel architectures, it has been observed that intense TX +traffic bursts of short packets may result in an improper descriptor +writeback. If this occurs, the driver will report a "TX Timeout" and reset +the adapter, after which the transmit flow will restart, though data may +have stalled for as much as 10 seconds before it resumes. + +The improper writeback does not occur on the first descriptor in a system +memory cache-line, which is typically 32 bytes, or 4 descriptors long. + +Setting TxDescriptorStep to a value of 4 will ensure that all TX descriptors +are aligned to the start of a system memory cache line, and so this problem +will not occur. + +NOTES: Setting TxDescriptorStep to 4 effectively reduces the number of + TxDescriptors available for transmits to 1/4 of the normal allocation. + This has a possible negative performance impact, which may be + compensated for by allocating more descriptors using the TxDescriptors + module parameter. + + There are other conditions which may result in "TX Timeout", which will + not be resolved by the use of the TxDescriptorStep parameter. As the + issue addressed by this parameter has never been observed on Intel + Architecture platforms, it should not be used on Intel platforms. TxIntDelay ---------- @@ -307,7 +284,6 @@ efficiency if properly tuned for specific network traffic. If the system is reporting dropped transmits, this value may be set too high causing the driver to run out of available transmit descriptors. - TxAbsIntDelay ------------- (This parameter is supported only on 82540, 82545 and later adapters.) @@ -330,6 +306,35 @@ Default Value: 1 A value of '1' indicates that the driver should enable IP checksum offload for received packets (both UDP and TCP) to the adapter hardware. +Copybreak +--------- +Valid Range: 0-xxxxxxx (0=off) +Default Value: 256 +Usage: insmod e1000.ko copybreak=128 + +Driver copies all packets below or equaling this size to a fresh Rx +buffer before handing it up the stack. + +This parameter is different than other parameters, in that it is a +single (not 1,1,1 etc.) parameter applied to all driver instances and +it is also available during runtime at +/sys/module/e1000/parameters/copybreak + +SmartPowerDownEnable +-------------------- +Valid Range: 0-1 +Default Value: 0 (disabled) + +Allows PHY to turn off in lower power states. The user can turn off +this parameter in supported chipsets. + +KumeranLockLoss +--------------- +Valid Range: 0-1 +Default Value: 1 (enabled) + +This workaround skips resetting the PHY at shutdown for the initial +silicon releases of ICH8 systems. Speed and Duplex Configuration ============================== @@ -385,40 +390,9 @@ If the link partner is forced to a specific speed and duplex, then this parameter should not be used. Instead, use the Speed and Duplex parameters previously mentioned to force the adapter to the same speed and duplex. - Additional Configurations ========================= - Configuring the Driver on Different Distributions - ------------------------------------------------- - Configuring a network driver to load properly when the system is started - is distribution dependent. Typically, the configuration process involves - adding an alias line to /etc/modules.conf or /etc/modprobe.conf as well - as editing other system startup scripts and/or configuration files. Many - popular Linux distributions ship with tools to make these changes for you. - To learn the proper way to configure a network device for your system, - refer to your distribution documentation. If during this process you are - asked for the driver or module name, the name for the Linux Base Driver - for the Intel(R) PRO/1000 Family of Adapters is e1000. - - As an example, if you install the e1000 driver for two PRO/1000 adapters - (eth0 and eth1) and set the speed and duplex to 10full and 100half, add - the following to modules.conf or or modprobe.conf: - - alias eth0 e1000 - alias eth1 e1000 - options e1000 Speed=10,100 Duplex=2,1 - - Viewing Link Messages - --------------------- - Link messages will not be displayed to the console if the distribution is - restricting system messages. In order to see network driver link messages - on your console, set dmesg to eight by entering the following: - - dmesg -n 8 - - NOTE: This setting is not saved across reboots. - Jumbo Frames ------------ Jumbo Frames support is enabled by changing the MTU to a value larger than @@ -437,9 +411,11 @@ Additional Configurations setting in a different location. Notes: - - - To enable Jumbo Frames, increase the MTU size on the interface beyond - 1500. + Degradation in throughput performance may be observed in some Jumbo frames + environments. If this is observed, increasing the application's socket buffer + size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help. + See the specific application manual and /usr/src/linux*/Documentation/ + networking/ip-sysctl.txt for more details. - The maximum MTU setting for Jumbo Frames is 16110. This value coincides with the maximum Jumbo Frames size of 16128. @@ -447,40 +423,11 @@ Additional Configurations - Using Jumbo Frames at 10 or 100 Mbps may result in poor performance or loss of link. - - Some Intel gigabit adapters that support Jumbo Frames have a frame size - limit of 9238 bytes, with a corresponding MTU size limit of 9216 bytes. - The adapters with this limitation are based on the Intel(R) 82571EB, - 82572EI, 82573L and 80003ES2LAN controller. These correspond to the - following product names: - Intel(R) PRO/1000 PT Server Adapter - Intel(R) PRO/1000 PT Desktop Adapter - Intel(R) PRO/1000 PT Network Connection - Intel(R) PRO/1000 PT Dual Port Server Adapter - Intel(R) PRO/1000 PT Dual Port Network Connection - Intel(R) PRO/1000 PF Server Adapter - Intel(R) PRO/1000 PF Network Connection - Intel(R) PRO/1000 PF Dual Port Server Adapter - Intel(R) PRO/1000 PB Server Connection - Intel(R) PRO/1000 PL Network Connection - Intel(R) PRO/1000 EB Network Connection with I/O Acceleration - Intel(R) PRO/1000 EB Backplane Connection with I/O Acceleration - Intel(R) PRO/1000 PT Quad Port Server Adapter - - Adapters based on the Intel(R) 82542 and 82573V/E controller do not support Jumbo Frames. These correspond to the following product names: Intel(R) PRO/1000 Gigabit Server Adapter Intel(R) PRO/1000 PM Network Connection - - The following adapters do not support Jumbo Frames: - Intel(R) 82562V 10/100 Network Connection - Intel(R) 82566DM Gigabit Network Connection - Intel(R) 82566DC Gigabit Network Connection - Intel(R) 82566MM Gigabit Network Connection - Intel(R) 82566MC Gigabit Network Connection - Intel(R) 82562GT 10/100 Network Connection - Intel(R) 82562G 10/100 Network Connection - - Ethtool ------- The driver utilizes the ethtool interface for driver configuration and @@ -490,142 +437,14 @@ Additional Configurations The latest release of ethtool can be found from http://sourceforge.net/projects/gkernel. - NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support - for a more complete ethtool feature set can be enabled by upgrading - ethtool to ethtool-1.8.1. - Enabling Wake on LAN* (WoL) --------------------------- - WoL is configured through the Ethtool* utility. Ethtool is included with - all versions of Red Hat after Red Hat 7.2. For other Linux distributions, - download and install Ethtool from the following website: - http://sourceforge.net/projects/gkernel. - - For instructions on enabling WoL with Ethtool, refer to the website listed - above. + WoL is configured through the Ethtool* utility. WoL will be enabled on the system during the next shut down or reboot. For this driver version, in order to enable WoL, the e1000 driver must be loaded when shutting down or rebooting the system. - Wake On LAN is only supported on port A for the following devices: - Intel(R) PRO/1000 PT Dual Port Network Connection - Intel(R) PRO/1000 PT Dual Port Server Connection - Intel(R) PRO/1000 PT Dual Port Server Adapter - Intel(R) PRO/1000 PF Dual Port Server Adapter - Intel(R) PRO/1000 PT Quad Port Server Adapter - - NAPI - ---- - NAPI (Rx polling mode) is enabled in the e1000 driver. - - See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI. - - -Known Issues -============ - -Dropped Receive Packets on Half-duplex 10/100 Networks ------------------------------------------------------- -If you have an Intel PCI Express adapter running at 10mbps or 100mbps, half- -duplex, you may observe occasional dropped receive packets. There are no -workarounds for this problem in this network configuration. The network must -be updated to operate in full-duplex, and/or 1000mbps only. - -Jumbo Frames System Requirement -------------------------------- -Memory allocation failures have been observed on Linux systems with 64 MB -of RAM or less that are running Jumbo Frames. If you are using Jumbo -Frames, your system may require more than the advertised minimum -requirement of 64 MB of system memory. - -Performance Degradation with Jumbo Frames ------------------------------------------ -Degradation in throughput performance may be observed in some Jumbo frames -environments. If this is observed, increasing the application's socket -buffer size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values -may help. See the specific application manual and -/usr/src/linux*/Documentation/ -networking/ip-sysctl.txt for more details. - -Jumbo Frames on Foundry BigIron 8000 switch -------------------------------------------- -There is a known issue using Jumbo frames when connected to a Foundry -BigIron 8000 switch. This is a 3rd party limitation. If you experience -loss of packets, lower the MTU size. - -Allocating Rx Buffers when Using Jumbo Frames ---------------------------------------------- -Allocating Rx buffers when using Jumbo Frames on 2.6.x kernels may fail if -the available memory is heavily fragmented. This issue may be seen with PCI-X -adapters or with packet split disabled. This can be reduced or eliminated -by changing the amount of available memory for receive buffer allocation, by -increasing /proc/sys/vm/min_free_kbytes. - -Multiple Interfaces on Same Ethernet Broadcast Network ------------------------------------------------------- -Due to the default ARP behavior on Linux, it is not possible to have -one system on two IP networks in the same Ethernet broadcast domain -(non-partitioned switch) behave as expected. All Ethernet interfaces -will respond to IP traffic for any IP address assigned to the system. -This results in unbalanced receive traffic. - -If you have multiple interfaces in a server, either turn on ARP -filtering by entering: - - echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter -(this only works if your kernel's version is higher than 2.4.5), - -NOTE: This setting is not saved across reboots. The configuration -change can be made permanent by adding the line: - net.ipv4.conf.all.arp_filter = 1 -to the file /etc/sysctl.conf - - or, - -install the interfaces in separate broadcast domains (either in -different switches or in a switch partitioned to VLANs). - -82541/82547 can't link or are slow to link with some link partners ------------------------------------------------------------------ -There is a known compatibility issue with 82541/82547 and some -low-end switches where the link will not be established, or will -be slow to establish. In particular, these switches are known to -be incompatible with 82541/82547: - - Planex FXG-08TE - I-O Data ETG-SH8 - -To workaround this issue, the driver can be compiled with an override -of the PHY's master/slave setting. Forcing master or forcing slave -mode will improve time-to-link. - - # make CFLAGS_EXTRA=-DE1000_MASTER_SLAVE=<n> - -Where <n> is: - - 0 = Hardware default - 1 = Master mode - 2 = Slave mode - 3 = Auto master/slave - -Disable rx flow control with ethtool ------------------------------------- -In order to disable receive flow control using ethtool, you must turn -off auto-negotiation on the same command line. - -For example: - - ethtool -A eth? autoneg off rx off - -Unplugging network cable while ethtool -p is running ----------------------------------------------------- -In kernel versions 2.5.50 and later (including 2.6 kernel), unplugging -the network cable while ethtool -p is running will cause the system to -become unresponsive to keyboard commands, except for control-alt-delete. -Restarting the system appears to be the only remedy. - - Support ======= diff --git a/Documentation/networking/e1000e.txt b/Documentation/networking/e1000e.txt new file mode 100644 index 00000000000..6aa048badf3 --- /dev/null +++ b/Documentation/networking/e1000e.txt @@ -0,0 +1,302 @@ +Linux* Driver for Intel(R) Network Connection +=============================================================== + +Intel Gigabit Linux driver. +Copyright(c) 1999 - 2010 Intel Corporation. + +Contents +======== + +- Identifying Your Adapter +- Command Line Parameters +- Additional Configurations +- Support + +Identifying Your Adapter +======================== + +The e1000e driver supports all PCI Express Intel(R) Gigabit Network +Connections, except those that are 82575, 82576 and 82580-based*. + +* NOTE: The Intel(R) PRO/1000 P Dual Port Server Adapter is supported by + the e1000 driver, not the e1000e driver due to the 82546 part being used + behind a PCI Express bridge. + +For more information on how to identify your adapter, go to the Adapter & +Driver ID Guide at: + + http://support.intel.com/support/go/network/adapter/idguide.htm + +For the latest Intel network drivers for Linux, refer to the following +website. In the search field, enter your adapter name or type, or use the +networking link on the left to search for your adapter: + + http://support.intel.com/support/go/network/adapter/home.htm + +Command Line Parameters +======================= + +The default value for each parameter is generally the recommended setting, +unless otherwise noted. + +NOTES: For more information about the InterruptThrottleRate, + RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay + parameters, see the application note at: + http://www.intel.com/design/network/applnots/ap450.htm + +InterruptThrottleRate +--------------------- +Valid Range: 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative, + 4=simplified balancing) +Default Value: 3 + +The driver can limit the amount of interrupts per second that the adapter +will generate for incoming packets. It does this by writing a value to the +adapter that is based on the maximum amount of interrupts that the adapter +will generate per second. + +Setting InterruptThrottleRate to a value greater or equal to 100 +will program the adapter to send out a maximum of that many interrupts +per second, even if more packets have come in. This reduces interrupt +load on the system and can lower CPU utilization under heavy load, +but will increase latency as packets are not processed as quickly. + +The driver has two adaptive modes (setting 1 or 3) in which +it dynamically adjusts the InterruptThrottleRate value based on the traffic +that it receives. After determining the type of incoming traffic in the last +timeframe, it will adjust the InterruptThrottleRate to an appropriate value +for that traffic. + +The algorithm classifies the incoming traffic every interval into +classes. Once the class is determined, the InterruptThrottleRate value is +adjusted to suit that traffic type the best. There are three classes defined: +"Bulk traffic", for large amounts of packets of normal size; "Low latency", +for small amounts of traffic and/or a significant percentage of small +packets; and "Lowest latency", for almost completely small packets or +minimal traffic. + +In dynamic conservative mode, the InterruptThrottleRate value is set to 4000 +for traffic that falls in class "Bulk traffic". If traffic falls in the "Low +latency" or "Lowest latency" class, the InterruptThrottleRate is increased +stepwise to 20000. This default mode is suitable for most applications. + +For situations where low latency is vital such as cluster or +grid computing, the algorithm can reduce latency even more when +InterruptThrottleRate is set to mode 1. In this mode, which operates +the same as mode 3, the InterruptThrottleRate will be increased stepwise to +70000 for traffic in class "Lowest latency". + +In simplified mode the interrupt rate is based on the ratio of Tx and +Rx traffic. If the bytes per second rate is approximately equal the +interrupt rate will drop as low as 2000 interrupts per second. If the +traffic is mostly transmit or mostly receive, the interrupt rate could +be as high as 8000. + +Setting InterruptThrottleRate to 0 turns off any interrupt moderation +and may improve small packet latency, but is generally not suitable +for bulk throughput traffic. + +NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and + RxAbsIntDelay parameters. In other words, minimizing the receive + and/or transmit absolute delays does not force the controller to + generate more interrupts than what the Interrupt Throttle Rate + allows. + +NOTE: When e1000e is loaded with default settings and multiple adapters + are in use simultaneously, the CPU utilization may increase non- + linearly. In order to limit the CPU utilization without impacting + the overall throughput, we recommend that you load the driver as + follows: + + modprobe e1000e InterruptThrottleRate=3000,3000,3000 + + This sets the InterruptThrottleRate to 3000 interrupts/sec for + the first, second, and third instances of the driver. The range + of 2000 to 3000 interrupts per second works on a majority of + systems and is a good starting point, but the optimal value will + be platform-specific. If CPU utilization is not a concern, use + RX_POLLING (NAPI) and default driver settings. + +RxIntDelay +---------- +Valid Range: 0-65535 (0=off) +Default Value: 0 + +This value delays the generation of receive interrupts in units of 1.024 +microseconds. Receive interrupt reduction can improve CPU efficiency if +properly tuned for specific network traffic. Increasing this value adds +extra latency to frame reception and can end up decreasing the throughput +of TCP traffic. If the system is reporting dropped receives, this value +may be set too high, causing the driver to run out of available receive +descriptors. + +CAUTION: When setting RxIntDelay to a value other than 0, adapters may + hang (stop transmitting) under certain network conditions. If + this occurs a NETDEV WATCHDOG message is logged in the system + event log. In addition, the controller is automatically reset, + restoring the network connection. To eliminate the potential + for the hang ensure that RxIntDelay is set to 0. + +RxAbsIntDelay +------------- +Valid Range: 0-65535 (0=off) +Default Value: 8 + +This value, in units of 1.024 microseconds, limits the delay in which a +receive interrupt is generated. Useful only if RxIntDelay is non-zero, +this value ensures that an interrupt is generated after the initial +packet is received within the set amount of time. Proper tuning, +along with RxIntDelay, may improve traffic throughput in specific network +conditions. + +TxIntDelay +---------- +Valid Range: 0-65535 (0=off) +Default Value: 8 + +This value delays the generation of transmit interrupts in units of +1.024 microseconds. Transmit interrupt reduction can improve CPU +efficiency if properly tuned for specific network traffic. If the +system is reporting dropped transmits, this value may be set too high +causing the driver to run out of available transmit descriptors. + +TxAbsIntDelay +------------- +Valid Range: 0-65535 (0=off) +Default Value: 32 + +This value, in units of 1.024 microseconds, limits the delay in which a +transmit interrupt is generated. Useful only if TxIntDelay is non-zero, +this value ensures that an interrupt is generated after the initial +packet is sent on the wire within the set amount of time. Proper tuning, +along with TxIntDelay, may improve traffic throughput in specific +network conditions. + +Copybreak +--------- +Valid Range: 0-xxxxxxx (0=off) +Default Value: 256 + +Driver copies all packets below or equaling this size to a fresh Rx +buffer before handing it up the stack. + +This parameter is different than other parameters, in that it is a +single (not 1,1,1 etc.) parameter applied to all driver instances and +it is also available during runtime at +/sys/module/e1000e/parameters/copybreak + +SmartPowerDownEnable +-------------------- +Valid Range: 0-1 +Default Value: 0 (disabled) + +Allows PHY to turn off in lower power states. The user can set this parameter +in supported chipsets. + +KumeranLockLoss +--------------- +Valid Range: 0-1 +Default Value: 1 (enabled) + +This workaround skips resetting the PHY at shutdown for the initial +silicon releases of ICH8 systems. + +IntMode +------- +Valid Range: 0-2 (0=legacy, 1=MSI, 2=MSI-X) +Default Value: 2 + +Allows changing the interrupt mode at module load time, without requiring a +recompile. If the driver load fails to enable a specific interrupt mode, the +driver will try other interrupt modes, from least to most compatible. The +interrupt order is MSI-X, MSI, Legacy. If specifying MSI (IntMode=1) +interrupts, only MSI and Legacy will be attempted. + +CrcStripping +------------ +Valid Range: 0-1 +Default Value: 1 (enabled) + +Strip the CRC from received packets before sending up the network stack. If +you have a machine with a BMC enabled but cannot receive IPMI traffic after +loading or enabling the driver, try disabling this feature. + +WriteProtectNVM +--------------- +Valid Range: 0-1 +Default Value: 1 (enabled) + +Set the hardware to ignore all write/erase cycles to the GbE region in the +ICHx NVM (non-volatile memory). This feature can be disabled by the +WriteProtectNVM module parameter (enabled by default) only after a hardware +reset, but the machine must be power cycled before trying to enable writes. + +Note: the kernel boot option iomem=relaxed may need to be set if the kernel +config option CONFIG_STRICT_DEVMEM=y, if the root user wants to write the +NVM from user space via ethtool. + +Additional Configurations +========================= + + Jumbo Frames + ------------ + Jumbo Frames support is enabled by changing the MTU to a value larger than + the default of 1500. Use the ifconfig command to increase the MTU size. + For example: + + ifconfig eth<x> mtu 9000 up + + This setting is not saved across reboots. + + Notes: + + - The maximum MTU setting for Jumbo Frames is 9216. This value coincides + with the maximum Jumbo Frames size of 9234 bytes. + + - Using Jumbo Frames at 10 or 100 Mbps is not supported and may result in + poor performance or loss of link. + + - Some adapters limit Jumbo Frames sized packets to a maximum of + 4096 bytes and some adapters do not support Jumbo Frames. + + + Ethtool + ------- + The driver utilizes the ethtool interface for driver configuration and + diagnostics, as well as displaying statistical information. We + strongly recommend downloading the latest version of Ethtool at: + + http://sourceforge.net/projects/gkernel. + + Speed and Duplex + ---------------- + Speed and Duplex are configured through the Ethtool* utility. For + instructions, refer to the Ethtool man page. + + Enabling Wake on LAN* (WoL) + --------------------------- + WoL is configured through the Ethtool* utility. For instructions on + enabling WoL with Ethtool, refer to the Ethtool man page. + + WoL will be enabled on the system during the next shut down or reboot. + For this driver version, in order to enable WoL, the e1000e driver must be + loaded when shutting down or rebooting the system. + + In most cases Wake On LAN is only supported on port A for multiple port + adapters. To verify if a port supports Wake on LAN run ethtool eth<X>. + + +Support +======= + +For general information, go to the Intel support website at: + + www.intel.com/support/ + +or the Intel Wired Networking project hosted by Sourceforge at: + + http://sourceforge.net/projects/e1000 + +If an issue is identified with the released source code on the supported +kernel with a supported adapter, email the specific information related +to the issue to e1000-devel@lists.sf.net diff --git a/Documentation/networking/ixgbevf.txt b/Documentation/networking/ixgbevf.txt index 19015de6725..21dd5d15b6b 100755..100644 --- a/Documentation/networking/ixgbevf.txt +++ b/Documentation/networking/ixgbevf.txt @@ -1,19 +1,16 @@ Linux* Base Driver for Intel(R) Network Connection ================================================== -November 24, 2009 +Intel Gigabit Linux driver. +Copyright(c) 1999 - 2010 Intel Corporation. Contents ======== -- In This Release - Identifying Your Adapter - Known Issues/Troubleshooting - Support -In This Release -=============== - This file describes the ixgbevf Linux* Base Driver for Intel Network Connection. @@ -33,7 +30,7 @@ Identifying Your Adapter For more information on how to identify your adapter, go to the Adapter & Driver ID Guide at: - http://support.intel.com/support/network/sb/CS-008441.htm + http://support.intel.com/support/go/network/adapter/idguide.htm Known Issues/Troubleshooting ============================ @@ -57,34 +54,3 @@ or the Intel Wired Networking project hosted by Sourceforge at: If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information related to the issue to e1000-devel@lists.sf.net - -License -======= - -Intel 10 Gigabit Linux driver. -Copyright(c) 1999 - 2009 Intel Corporation. - -This program is free software; you can redistribute it and/or modify it -under the terms and conditions of the GNU General Public License, -version 2, as published by the Free Software Foundation. - -This program is distributed in the hope it will be useful, but WITHOUT -ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or -FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for -more details. - -You should have received a copy of the GNU General Public License along with -this program; if not, write to the Free Software Foundation, Inc., -51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. - -The full GNU General Public License is included in this distribution in -the file called "COPYING". - -Trademarks -========== - -Intel, Itanium, and Pentium are trademarks or registered trademarks of -Intel Corporation or its subsidiaries in the United States and other -countries. - -* Other names and brands may be claimed as the property of others. diff --git a/Documentation/vm/page-types.c b/Documentation/vm/page-types.c index ccd951fa94e..cc96ee2666f 100644 --- a/Documentation/vm/page-types.c +++ b/Documentation/vm/page-types.c @@ -478,7 +478,7 @@ static void prepare_hwpoison_fd(void) } if (opt_unpoison && !hwpoison_forget_fd) { - sprintf(buf, "%s/renew-pfn", hwpoison_debug_fs); + sprintf(buf, "%s/unpoison-pfn", hwpoison_debug_fs); hwpoison_forget_fd = checked_open(buf, O_WRONLY); } } |