diff options
Diffstat (limited to 'Documentation')
20 files changed, 353 insertions, 14 deletions
diff --git a/Documentation/ABI/testing/ima_policy b/Documentation/ABI/testing/ima_policy index 98694661354..ec0a38ef314 100644 --- a/Documentation/ABI/testing/ima_policy +++ b/Documentation/ABI/testing/ima_policy @@ -23,7 +23,7 @@ Description: lsm: [[subj_user=] [subj_role=] [subj_type=] [obj_user=] [obj_role=] [obj_type=]] - base: func:= [BPRM_CHECK][FILE_MMAP][FILE_CHECK] + base: func:= [BPRM_CHECK][FILE_MMAP][FILE_CHECK][MODULE_CHECK] mask:= [MAY_READ] [MAY_WRITE] [MAY_APPEND] [MAY_EXEC] fsmagic:= hex value uid:= decimal value @@ -53,6 +53,7 @@ Description: measure func=BPRM_CHECK measure func=FILE_MMAP mask=MAY_EXEC measure func=FILE_CHECK mask=MAY_READ uid=0 + measure func=MODULE_CHECK uid=0 appraise fowner=0 The default policy measures all executables in bprm_check, diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt index 49fc7ada929..3545ea704b5 100644 --- a/Documentation/devicetree/bindings/arm/davinci/nand.txt +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt @@ -23,6 +23,9 @@ Recommended properties : - ti,davinci-nand-buswidth: buswidth 8 or 16 - ti,davinci-nand-use-bbt: use flash based bad block table support. +nand device bindings may contain additional sub-nodes describing +partitions of the address space. See partition.txt for more detail. + Example(da850 EVM ): nand_cs3@62000000 { compatible = "ti,davinci-nand"; @@ -35,4 +38,9 @@ nand_cs3@62000000 { ti,davinci-ecc-mode = "hw"; ti,davinci-ecc-bits = <4>; ti,davinci-nand-use-bbt; + + partition@180000 { + label = "ubifs"; + reg = <0x180000 0x7e80000>; + }; }; diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt new file mode 100644 index 00000000000..b04d03a1d49 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt @@ -0,0 +1,23 @@ +* Denali NAND controller + +Required properties: + - compatible : should be "denali,denali-nand-dt" + - reg : should contain registers location and length for data and reg. + - reg-names: Should contain the reg names "nand_data" and "denali_reg" + - interrupts : The interrupt number. + - dm-mask : DMA bit mask + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Examples: + +nand: nand@ff900000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "denali,denali-nand-dt"; + reg = <0xff900000 0x100000>, <0xffb80000 0x10000>; + reg-names = "nand_data", "denali_reg"; + interrupts = <0 144 4>; + dma-mask = <0xffffffff>; +}; diff --git a/Documentation/devicetree/bindings/mtd/flctl-nand.txt b/Documentation/devicetree/bindings/mtd/flctl-nand.txt new file mode 100644 index 00000000000..427f46dc60a --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/flctl-nand.txt @@ -0,0 +1,49 @@ +FLCTL NAND controller + +Required properties: +- compatible : "renesas,shmobile-flctl-sh7372" +- reg : Address range of the FLCTL +- interrupts : flste IRQ number +- nand-bus-width : bus width to NAND chip + +Optional properties: +- dmas: DMA specifier(s) +- dma-names: name for each DMA specifier. Valid names are + "data_tx", "data_rx", "ecc_tx", "ecc_rx" + +The DMA fields are not used yet in the driver but are listed here for +completing the bindings. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + + flctl@e6a30000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "renesas,shmobile-flctl-sh7372"; + reg = <0xe6a30000 0x100>; + interrupts = <0x0d80>; + + nand-bus-width = <16>; + + dmas = <&dmac 1 /* data_tx */ + &dmac 2;> /* data_rx */ + dma-names = "data_tx", "data_rx"; + + system@0 { + label = "system"; + reg = <0x0 0x8000000>; + }; + + userdata@8000000 { + label = "userdata"; + reg = <0x8000000 0x10000000>; + }; + + cache@18000000 { + label = "cache"; + reg = <0x18000000 0x8000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt index e2c663b354d..e3ea32e7de3 100644 --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -3,9 +3,7 @@ Required properties: - compatible : "st,spear600-fsmc-nand" - reg : Address range of the mtd chip -- reg-names: Should contain the reg names "fsmc_regs" and "nand_data" -- st,ale-off : Chip specific offset to ALE -- st,cle-off : Chip specific offset to CLE +- reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd" Optional properties: - bank-width : Width (in bytes) of the device. If not present, the width @@ -19,10 +17,10 @@ Example: #address-cells = <1>; #size-cells = <1>; reg = <0xd1800000 0x1000 /* FSMC Register */ - 0xd2000000 0x4000>; /* NAND Base */ - reg-names = "fsmc_regs", "nand_data"; - st,ale-off = <0x20000>; - st,cle-off = <0x10000>; + 0xd2000000 0x0010 /* NAND Base DATA */ + 0xd2020000 0x0010 /* NAND Base ADDR */ + 0xd2010000 0x0010>; /* NAND Base CMD */ + reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd"; bank-width = <1>; nand-skip-bbtscan; diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/m25p80.txt new file mode 100644 index 00000000000..6d3d5760947 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/m25p80.txt @@ -0,0 +1,29 @@ +* MTD SPI driver for ST M25Pxx (and similar) serial flash chips + +Required properties: +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- compatible : Should be the manufacturer and the name of the chip. Bear in mind + the DT binding is not Linux-only, but in case of Linux, see the + "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of + supported chips. +- reg : Chip-Select number +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at + +Optional properties: +- m25p,fast-read : Use the "fast read" opcode to read data from the chip instead + of the usual "read" opcode. This opcode is not supported by + all chips and support for it can not be detected at runtime. + Refer to your chips' datasheet to check if this is supported + by your chip. + +Example: + + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + reg = <0>; + spi-max-frequency = <40000000>; + m25p,fast-read; + }; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index 94de19b8f16..dab7847fc80 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -23,6 +23,9 @@ file systems on embedded devices. unaligned accesses as implemented in the JFFS2 code via memcpy(). By defining "no-unaligned-direct-access", the flash will not be exposed directly to the MTD users (e.g. JFFS2) any more. + - linux,mtd-name: allow to specify the mtd name for retro capability with + physmap-flash drivers as boot loader pass the mtd partition via the old + device name physmap-flash. For JEDEC compatible devices, the following additional properties are defined: diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt new file mode 100644 index 00000000000..131e8c11d26 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -0,0 +1,23 @@ +TI SOC ECAP based APWM controller + +Required properties: +- compatible: Must be "ti,am33xx-ecap" +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the ECAP: + "ecap<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ecap0: ecap@0 { + compatible = "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48300100 0x80>; + ti,hwmods = "ecap0"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt new file mode 100644 index 00000000000..4fc7079d822 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt @@ -0,0 +1,23 @@ +TI SOC EHRPWM based PWM controller + +Required properties: +- compatible : Must be "ti,am33xx-ehrpwm" +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the EHRPWM: + "ehrpwm<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ehrpwm0: ehrpwm@0 { + compatible = "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48300200 0x100>; + ti,hwmods = "ehrpwm0"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt new file mode 100644 index 00000000000..f7eae77f835 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt @@ -0,0 +1,31 @@ +TI SOC based PWM Subsystem + +Required properties: +- compatible: Must be "ti,am33xx-pwmss"; +- reg: physical base address and size of the registers map. +- address-cells: Specify the number of u32 entries needed in child nodes. + Should set to 1. +- size-cells: specify number of u32 entries needed to specify child nodes size + in reg property. Should set to 1. +- ranges: describes the address mapping of a memory-mapped bus. Should set to + physical address map of child's base address, physical address within + parent's address space and length of the address map. For am33xx, + 3 set of child register maps present, ECAP register space, EQEP + register space, EHRPWM register space. + +Also child nodes should also populated under PWMSS DT node. + +Example: +pwmss0: pwmss@48300000 { + compatible = "ti,am33xx-pwmss"; + reg = <0x48300000 0x10>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + ranges = <0x48300100 0x48300100 0x80 /* ECAP */ + 0x48300180 0x48300180 0x80 /* EQEP */ + 0x48300200 0x48300200 0x80>; /* EHRPWM */ + + /* child nodes go here */ +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt index 73ec962bfe8..06e67247859 100644 --- a/Documentation/devicetree/bindings/pwm/pwm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm.txt @@ -37,10 +37,21 @@ device: pwm-names = "backlight"; }; +Note that in the example above, specifying the "pwm-names" is redundant +because the name "backlight" would be used as fallback anyway. + pwm-specifier typically encodes the chip-relative PWM number and the PWM -period in nanoseconds. Note that in the example above, specifying the -"pwm-names" is redundant because the name "backlight" would be used as -fallback anyway. +period in nanoseconds. + +Optionally, the pwm-specifier can encode a number of flags in a third cell: +- bit 0: PWM signal polarity (0: normal polarity, 1: inverse polarity) + +Example with optional PWM specifier for inverse polarity + + bl: backlight { + pwms = <&pwm 0 5000000 1>; + pwm-names = "backlight"; + }; 2) PWM controller nodes ----------------------- diff --git a/Documentation/devicetree/bindings/pwm/spear-pwm.txt b/Documentation/devicetree/bindings/pwm/spear-pwm.txt new file mode 100644 index 00000000000..3ac779d8338 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/spear-pwm.txt @@ -0,0 +1,18 @@ +== ST SPEAr SoC PWM controller == + +Required properties: +- compatible: should be one of: + - "st,spear320-pwm" + - "st,spear1340-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: number of cells used to specify PWM which is fixed to 2 on + SPEAr. The first cell specifies the per-chip index of the PWM to use and + the second cell is the period in nanoseconds. + +Example: + + pwm: pwm@a8000000 { + compatible ="st,spear320-pwm"; + reg = <0xa8000000 0x1000>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt new file mode 100644 index 00000000000..2943ee5fce0 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers + +Supported PWMs: +On TWL4030 series: PWM1 and PWM2 +On TWL6030 series: PWM0 and PWM1 + +Required properties: +- compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm" +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + +Example: + +twl_pwm: pwm { + compatible = "ti,twl6030-pwm"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt new file mode 100644 index 00000000000..cb64f3acc10 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers connected to LED terminals + +Supported PWMs: +On TWL4030 series: PWMA and PWMB (connected to LEDA and LEDB terminals) +On TWL6030 series: LED PWM (mainly used as charging indicator LED) + +Required properties: +- compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled" +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + +Example: + +twl_pwmled: pwmled { + compatible = "ti,twl6030-pwmled"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt new file mode 100644 index 00000000000..bcc63678a9a --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt @@ -0,0 +1,17 @@ +VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller + +Required properties: +- compatible: should be "via,vt8500-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. +- clocks: phandle to the PWM source clock + +Example: + +pwm1: pwm@d8220000 { + #pwm-cells = <2>; + compatible = "via,vt8500-pwm"; + reg = <0xd8220000 0x1000>; + clocks = <&clkpwm>; +}; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt index 8cf24f6f0a9..7b53da5cb75 100644 --- a/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt @@ -13,7 +13,7 @@ Recommended properties: Example: -spi@7000d600 { +spi@7000c380 { compatible = "nvidia,tegra20-sflash"; reg = <0x7000c380 0x80>; interrupts = <0 39 0x04>; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt index f5b1ad1a1ec..eefe15e3d95 100644 --- a/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt @@ -13,7 +13,7 @@ Recommended properties: Example: -slink@7000d600 { +spi@7000d600 { compatible = "nvidia,tegra20-slink"; reg = <0x7000d600 0x200>; interrupts = <0 82 0x04>; diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt new file mode 100644 index 00000000000..07e04cdc0c9 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt @@ -0,0 +1,26 @@ +Atmel SPI device + +Required properties: +- compatible : should be "atmel,at91rm9200-spi". +- reg: Address and length of the register set for the device +- interrupts: Should contain spi interrupt +- cs-gpios: chipselects + +Example: + +spi1: spi@fffcc000 { + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffcc000 0x4000>; + interrupts = <13 4 5>; + #address-cells = <1>; + #size-cells = <0>; + cs-gpios = <&pioB 3 0>; + status = "okay"; + + mmc-slot@0 { + compatible = "mmc-spi-slot"; + reg = <0>; + gpios = <&pioC 4 0>; /* CD */ + spi-max-frequency = <25000000>; + }; +}; diff --git a/Documentation/x86/boot.txt b/Documentation/x86/boot.txt index f15cb74c4f7..406d82d5d2b 100644 --- a/Documentation/x86/boot.txt +++ b/Documentation/x86/boot.txt @@ -373,7 +373,7 @@ Protocol: 2.00+ 1 Loadlin 2 bootsect-loader (0x20, all other values reserved) 3 Syslinux - 4 Etherboot/gPXE + 4 Etherboot/gPXE/iPXE 5 ELILO 7 GRUB 8 U-Boot @@ -381,6 +381,7 @@ Protocol: 2.00+ A Gujin B Qemu C Arcturus Networks uCbootloader + D kexec-tools E Extended (see ext_loader_type) F Special (0xFF = undefined) 10 Reserved diff --git a/Documentation/xtensa/atomctl.txt b/Documentation/xtensa/atomctl.txt new file mode 100644 index 00000000000..10a8d1ff35e --- /dev/null +++ b/Documentation/xtensa/atomctl.txt @@ -0,0 +1,44 @@ +We Have Atomic Operation Control (ATOMCTL) Register. +This register determines the effect of using a S32C1I instruction +with various combinations of: + + 1. With and without an Coherent Cache Controller which + can do Atomic Transactions to the memory internally. + + 2. With and without An Intelligent Memory Controller which + can do Atomic Transactions itself. + +The Core comes up with a default value of for the three types of cache ops: + + 0x28: (WB: Internal, WT: Internal, BY:Exception) + +On the FPGA Cards we typically simulate an Intelligent Memory controller +which can implement RCW transactions. For FPGA cards with an External +Memory controller we let it to the atomic operations internally while +doing a Cached (WB) transaction and use the Memory RCW for un-cached +operations. + +For systems without an coherent cache controller, non-MX, we always +use the memory controllers RCW, thought non-MX controlers likely +support the Internal Operation. + +CUSTOMER-WARNING: + Virtually all customers buy their memory controllers from vendors that + don't support atomic RCW memory transactions and will likely want to + configure this register to not use RCW. + +Developers might find using RCW in Bypass mode convenient when testing +with the cache being bypassed; for example studying cache alias problems. + +See Section 4.3.12.4 of ISA; Bits: + + WB WT BY + 5 4 | 3 2 | 1 0 + 2 Bit + Field + Values WB - Write Back WT - Write Thru BY - Bypass +--------- --------------- ----------------- ---------------- + 0 Exception Exception Exception + 1 RCW Transaction RCW Transaction RCW Transaction + 2 Internal Operation Exception Reserved + 3 Reserved Reserved Reserved |