diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/arm/mem_alignment | 2 | ||||
| -rw-r--r-- | Documentation/kernel-parameters.txt | 4 | ||||
| -rw-r--r-- | Documentation/local_ops.txt | 2 | ||||
| -rw-r--r-- | Documentation/usb/gadget_serial.txt | 4 | ||||
| -rw-r--r-- | Documentation/usb/proc_usb_info.txt | 6 | ||||
| -rw-r--r-- | Documentation/usb/usbmon.txt | 12 |
6 files changed, 19 insertions, 11 deletions
diff --git a/Documentation/arm/mem_alignment b/Documentation/arm/mem_alignment index d145ccca169..c7c7a114c78 100644 --- a/Documentation/arm/mem_alignment +++ b/Documentation/arm/mem_alignment @@ -24,7 +24,7 @@ real bad - it changes the behaviour of all unaligned instructions in user space, and might cause programs to fail unexpectedly. To change the alignment trap behavior, simply echo a number into -/proc/sys/debug/alignment. The number is made up from various bits: +/proc/cpu/alignment. The number is made up from various bits: bit behavior when set --- ----------------- diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 2919a2e9193..edab81c1318 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -89,6 +89,7 @@ parameter is applicable: SPARC Sparc architecture is enabled. SWSUSP Software suspend (hibernation) is enabled. SUSPEND System suspend states are enabled. + FTRACE Function tracing enabled. TS Appropriate touchscreen support is enabled. USB USB support is enabled. USBHID USB Human Interface Device support is enabled. @@ -2173,6 +2174,9 @@ and is between 256 and 4096 characters. It is defined in the file st= [HW,SCSI] SCSI tape parameters (buffers, etc.) See Documentation/scsi/st.txt. + stacktrace [FTRACE] + Enabled the stack tracer on boot up. + sti= [PARISC,HW] Format: <num> Set the STI (builtin display/keyboard on the HP-PARISC diff --git a/Documentation/local_ops.txt b/Documentation/local_ops.txt index f4f8b1c6c8b..23045b8b50f 100644 --- a/Documentation/local_ops.txt +++ b/Documentation/local_ops.txt @@ -149,7 +149,7 @@ static void do_test_timer(unsigned long data) int cpu; /* Increment the counters */ - on_each_cpu(test_each, NULL, 0, 1); + on_each_cpu(test_each, NULL, 1); /* Read all the counters */ printk("Counters read from CPU %d\n", smp_processor_id()); for_each_online_cpu(cpu) { diff --git a/Documentation/usb/gadget_serial.txt b/Documentation/usb/gadget_serial.txt index 9b22bd14c34..eac7df94d8e 100644 --- a/Documentation/usb/gadget_serial.txt +++ b/Documentation/usb/gadget_serial.txt @@ -114,11 +114,11 @@ modules. Then you must load the gadget serial driver. To load it as an ACM device (recommended for interoperability), do this: - modprobe g_serial use_acm=1 + modprobe g_serial To load it as a vendor specific bulk in/out device, do this: - modprobe g_serial + modprobe g_serial use_acm=0 This will also automatically load the underlying gadget peripheral controller driver. This must be done each time you reboot the gadget diff --git a/Documentation/usb/proc_usb_info.txt b/Documentation/usb/proc_usb_info.txt index 077e9032d0c..fafcd472326 100644 --- a/Documentation/usb/proc_usb_info.txt +++ b/Documentation/usb/proc_usb_info.txt @@ -49,8 +49,10 @@ it and 002/048 sometime later. These files can be read as binary data. The binary data consists of first the device descriptor, then the descriptors for each -configuration of the device. That information is also shown in -text form by the /proc/bus/usb/devices file, described later. +configuration of the device. Multi-byte fields in the device and +configuration descriptors, but not other descriptors, are converted +to host endianness by the kernel. This information is also shown +in text form by the /proc/bus/usb/devices file, described later. These files may also be used to write user-level drivers for the USB devices. You would open the /proc/bus/usb/BBB/DDD file read/write, diff --git a/Documentation/usb/usbmon.txt b/Documentation/usb/usbmon.txt index 2917ce4ffdc..270481906dc 100644 --- a/Documentation/usb/usbmon.txt +++ b/Documentation/usb/usbmon.txt @@ -34,11 +34,12 @@ if usbmon is built into the kernel. Verify that bus sockets are present. # ls /sys/kernel/debug/usbmon -0s 0t 0u 1s 1t 1u 2s 2t 2u 3s 3t 3u 4s 4t 4u +0s 0u 1s 1t 1u 2s 2t 2u 3s 3t 3u 4s 4t 4u # -Now you can choose to either use the sockets numbered '0' (to capture packets on -all buses), and skip to step #3, or find the bus used by your device with step #2. +Now you can choose to either use the socket '0u' (to capture packets on all +buses), and skip to step #3, or find the bus used by your device with step #2. +This allows to filter away annoying devices that talk continuously. 2. Find which bus connects to the desired device @@ -99,8 +100,9 @@ on the event type, but there is a set of words, common for all types. Here is the list of words, from left to right: -- URB Tag. This is used to identify URBs is normally a kernel mode address - of the URB structure in hexadecimal. +- URB Tag. This is used to identify URBs, and is normally an in-kernel address + of the URB structure in hexadecimal, but can be a sequence number or any + other unique string, within reason. - Timestamp in microseconds, a decimal number. The timestamp's resolution depends on available clock, and so it can be much worse than a microsecond |