diff options
Diffstat (limited to 'Documentation')
-rw-r--r-- | Documentation/hwmon/abituguru-datasheet | 6 | ||||
-rw-r--r-- | Documentation/networking/rxrpc.txt | 2 | ||||
-rw-r--r-- | Documentation/scsi/ChangeLog.lpfc | 2 |
3 files changed, 5 insertions, 5 deletions
diff --git a/Documentation/hwmon/abituguru-datasheet b/Documentation/hwmon/abituguru-datasheet index aef5a9b3684..4d184f2db0e 100644 --- a/Documentation/hwmon/abituguru-datasheet +++ b/Documentation/hwmon/abituguru-datasheet @@ -74,7 +74,7 @@ a sensor. Notice that some banks have both a read and a write address this is how the uGuru determines if a read from or a write to the bank is taking place, thus when reading you should always use the read address and when writing the -write address. The write address is always one (1) more then the read address. +write address. The write address is always one (1) more than the read address. uGuru ready @@ -224,7 +224,7 @@ Bit 3: Beep if alarm (RW) Bit 4: 1 if alarm cause measured temp is over the warning threshold (R) Bit 5: 1 if alarm cause measured volt is over the max threshold (R) Bit 6: 1 if alarm cause measured volt is under the min threshold (R) -Bit 7: Volt sensor: Shutdown if alarm persist for more then 4 seconds (RW) +Bit 7: Volt sensor: Shutdown if alarm persist for more than 4 seconds (RW) Temp sensor: Shutdown if temp is over the shutdown threshold (RW) * This bit is only honored/used by the uGuru if a temp sensor is connected @@ -293,7 +293,7 @@ Byte 0: Alarm behaviour for the selected sensor. A 1 enables the described behaviour. Bit 0: Give an alarm if measured rpm is under the min threshold (RW) Bit 3: Beep if alarm (RW) -Bit 7: Shutdown if alarm persist for more then 4 seconds (RW) +Bit 7: Shutdown if alarm persist for more than 4 seconds (RW) Byte 1: min threshold (scale as bank 0x26) diff --git a/Documentation/networking/rxrpc.txt b/Documentation/networking/rxrpc.txt index c3669a3fb4a..60d05eb77c6 100644 --- a/Documentation/networking/rxrpc.txt +++ b/Documentation/networking/rxrpc.txt @@ -540,7 +540,7 @@ A client would issue an operation by: MSG_MORE should be set in msghdr::msg_flags on all but the last part of the request. Multiple requests may be made simultaneously. - If a call is intended to go to a destination other then the default + If a call is intended to go to a destination other than the default specified through connect(), then msghdr::msg_name should be set on the first request message of that call. diff --git a/Documentation/scsi/ChangeLog.lpfc b/Documentation/scsi/ChangeLog.lpfc index ae3f962a7cf..ff19a52fe00 100644 --- a/Documentation/scsi/ChangeLog.lpfc +++ b/Documentation/scsi/ChangeLog.lpfc @@ -733,7 +733,7 @@ Changes from 20040920 to 20041018 I/O completion path a little more, especially taking care of fast-pathing the non-error case. Also removes tons of dead members and defines from lpfc_scsi.h - e.g. lpfc_target is down - to nothing more then the lpfc_nodelist pointer. + to nothing more than the lpfc_nodelist pointer. * Added binary sysfs file to issue mbox commands * Replaced #if __BIG_ENDIAN with #if __BIG_ENDIAN_BITFIELD for compatibility with the user space applications. |