diff options
Diffstat (limited to 'Documentation')
3 files changed, 103 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/dma/bcm2835-dma.txt b/Documentation/devicetree/bindings/dma/bcm2835-dma.txt new file mode 100644 index 00000000000..1396078d15a --- /dev/null +++ b/Documentation/devicetree/bindings/dma/bcm2835-dma.txt @@ -0,0 +1,57 @@ +* BCM2835 DMA controller + +The BCM2835 DMA controller has 16 channels in total. +Only the lower 13 channels have an associated IRQ. +Some arbitrary channels are used by the firmware +(1,3,6,7 in the current firmware version). +The channels 0,2 and 3 have special functionality +and should not be used by the driver. + +Required properties: +- compatible: Should be "brcm,bcm2835-dma". +- reg: Should contain DMA registers location and length. +- interrupts: Should contain the DMA interrupts associated + to the DMA channels in ascending order. +- #dma-cells: Must be <1>, the cell in the dmas property of the + client device represents the DREQ number. +- brcm,dma-channel-mask: Bit mask representing the channels + not used by the firmware in ascending order, + i.e. first channel corresponds to LSB. + +Example: + +dma: dma@7e007000 { + compatible = "brcm,bcm2835-dma"; + reg = <0x7e007000 0xf00>; + interrupts = <1 16>, + <1 17>, + <1 18>, + <1 19>, + <1 20>, + <1 21>, + <1 22>, + <1 23>, + <1 24>, + <1 25>, + <1 26>, + <1 27>, + <1 28>; + + #dma-cells = <1>; + brcm,dma-channel-mask = <0x7f35>; +}; + +DMA clients connected to the BCM2835 DMA controller must use the format +described in the dma.txt file, using a two-cell specifier for each channel. + +Example: + +bcm2835_i2s: i2s@7e203000 { + compatible = "brcm,bcm2835-i2s"; + reg = < 0x7e203000 0x20>, + < 0x7e101098 0x02>; + + dmas = <&dma 2>, + <&dma 3>; + dma-names = "tx", "rx"; +}; diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index 4fa814d3832..68b83ecc385 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -42,6 +42,7 @@ The full ID of peripheral types can be found below. 19 IPU Memory 20 ASRC 21 ESAI + 22 SSI Dual FIFO (needs firmware ver >= 2) The third cell specifies the transfer priority as below. diff --git a/Documentation/devicetree/bindings/dma/moxa,moxart-dma.txt b/Documentation/devicetree/bindings/dma/moxa,moxart-dma.txt new file mode 100644 index 00000000000..8a9f3559335 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/moxa,moxart-dma.txt @@ -0,0 +1,45 @@ +MOXA ART DMA Controller + +See dma.txt first + +Required properties: + +- compatible : Must be "moxa,moxart-dma" +- reg : Should contain registers location and length +- interrupts : Should contain an interrupt-specifier for the sole + interrupt generated by the device +- #dma-cells : Should be 1, a single cell holding a line request number + +Example: + + dma: dma@90500000 { + compatible = "moxa,moxart-dma"; + reg = <0x90500080 0x40>; + interrupts = <24 0>; + #dma-cells = <1>; + }; + + +Clients: + +DMA clients connected to the MOXA ART DMA controller must use the format +described in the dma.txt file, using a two-cell specifier for each channel: +a phandle plus one integer cells. +The two cells in order are: + +1. A phandle pointing to the DMA controller. +2. Peripheral identifier for the hardware handshaking interface. + +Example: +Use specific request line passing from dma +For example, MMC request line is 5 + + sdhci: sdhci@98e00000 { + compatible = "moxa,moxart-sdhci"; + reg = <0x98e00000 0x5C>; + interrupts = <5 0>; + clocks = <&clk_apb>; + dmas = <&dma 5>, + <&dma 5>; + dma-names = "tx", "rx"; + }; |