diff options
Diffstat (limited to 'Documentation/vm')
| -rw-r--r-- | Documentation/vm/numa_memory_policy.txt | 68 |
1 files changed, 68 insertions, 0 deletions
diff --git a/Documentation/vm/numa_memory_policy.txt b/Documentation/vm/numa_memory_policy.txt index 27b9507a376..6719d642653 100644 --- a/Documentation/vm/numa_memory_policy.txt +++ b/Documentation/vm/numa_memory_policy.txt @@ -311,6 +311,74 @@ Components of Memory Policies MPOL_PREFERRED policies that were created with an empty nodemask (local allocation). +MEMORY POLICY REFERENCE COUNTING + +To resolve use/free races, struct mempolicy contains an atomic reference +count field. Internal interfaces, mpol_get()/mpol_put() increment and +decrement this reference count, respectively. mpol_put() will only free +the structure back to the mempolicy kmem cache when the reference count +goes to zero. + +When a new memory policy is allocated, it's reference count is initialized +to '1', representing the reference held by the task that is installing the +new policy. When a pointer to a memory policy structure is stored in another +structure, another reference is added, as the task's reference will be dropped +on completion of the policy installation. + +During run-time "usage" of the policy, we attempt to minimize atomic operations +on the reference count, as this can lead to cache lines bouncing between cpus +and NUMA nodes. "Usage" here means one of the following: + +1) querying of the policy, either by the task itself [using the get_mempolicy() + API discussed below] or by another task using the /proc/<pid>/numa_maps + interface. + +2) examination of the policy to determine the policy mode and associated node + or node lists, if any, for page allocation. This is considered a "hot + path". Note that for MPOL_BIND, the "usage" extends across the entire + allocation process, which may sleep during page reclaimation, because the + BIND policy nodemask is used, by reference, to filter ineligible nodes. + +We can avoid taking an extra reference during the usages listed above as +follows: + +1) we never need to get/free the system default policy as this is never + changed nor freed, once the system is up and running. + +2) for querying the policy, we do not need to take an extra reference on the + target task's task policy nor vma policies because we always acquire the + task's mm's mmap_sem for read during the query. The set_mempolicy() and + mbind() APIs [see below] always acquire the mmap_sem for write when + installing or replacing task or vma policies. Thus, there is no possibility + of a task or thread freeing a policy while another task or thread is + querying it. + +3) Page allocation usage of task or vma policy occurs in the fault path where + we hold them mmap_sem for read. Again, because replacing the task or vma + policy requires that the mmap_sem be held for write, the policy can't be + freed out from under us while we're using it for page allocation. + +4) Shared policies require special consideration. One task can replace a + shared memory policy while another task, with a distinct mmap_sem, is + querying or allocating a page based on the policy. To resolve this + potential race, the shared policy infrastructure adds an extra reference + to the shared policy during lookup while holding a spin lock on the shared + policy management structure. This requires that we drop this extra + reference when we're finished "using" the policy. We must drop the + extra reference on shared policies in the same query/allocation paths + used for non-shared policies. For this reason, shared policies are marked + as such, and the extra reference is dropped "conditionally"--i.e., only + for shared policies. + + Because of this extra reference counting, and because we must lookup + shared policies in a tree structure under spinlock, shared policies are + more expensive to use in the page allocation path. This is expecially + true for shared policies on shared memory regions shared by tasks running + on different NUMA nodes. This extra overhead can be avoided by always + falling back to task or system default policy for shared memory regions, + or by prefaulting the entire shared memory region into memory and locking + it down. However, this might not be appropriate for all applications. + MEMORY POLICY APIs Linux supports 3 system calls for controlling memory policy. These APIS |