aboutsummaryrefslogtreecommitdiff
path: root/Documentation/hwmon
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/hwmon')
-rw-r--r--Documentation/hwmon/pcf859128
-rw-r--r--Documentation/hwmon/tmp42136
-rw-r--r--Documentation/hwmon/wm831x37
-rw-r--r--Documentation/hwmon/wm835026
4 files changed, 114 insertions, 13 deletions
diff --git a/Documentation/hwmon/pcf8591 b/Documentation/hwmon/pcf8591
index 5628fcf4207..e76a7892f68 100644
--- a/Documentation/hwmon/pcf8591
+++ b/Documentation/hwmon/pcf8591
@@ -2,11 +2,11 @@ Kernel driver pcf8591
=====================
Supported chips:
- * Philips PCF8591
+ * Philips/NXP PCF8591
Prefix: 'pcf8591'
Addresses scanned: I2C 0x48 - 0x4f
- Datasheet: Publicly available at the Philips Semiconductor website
- http://www.semiconductors.philips.com/pip/PCF8591P.html
+ Datasheet: Publicly available at the NXP website
+ http://www.nxp.com/pip/PCF8591_6.html
Authors:
Aurelien Jarno <aurelien@aurel32.net>
@@ -16,9 +16,10 @@ Authors:
Description
-----------
+
The PCF8591 is an 8-bit A/D and D/A converter (4 analog inputs and one
-analog output) for the I2C bus produced by Philips Semiconductors. It
-is designed to provide a byte I2C interface to up to 4 separate devices.
+analog output) for the I2C bus produced by Philips Semiconductors (now NXP).
+It is designed to provide a byte I2C interface to up to 4 separate devices.
The PCF8591 has 4 analog inputs programmable as single-ended or
differential inputs :
@@ -58,8 +59,8 @@ Accessing PCF8591 via /sys interface
-------------------------------------
! Be careful !
-The PCF8591 is plainly impossible to detect ! Stupid chip.
-So every chip with address in the interval [48..4f] is
+The PCF8591 is plainly impossible to detect! Stupid chip.
+So every chip with address in the interval [0x48..0x4f] is
detected as PCF8591. If you have other chips in this address
range, the workaround is to load this module after the one
for your others chips.
@@ -67,19 +68,20 @@ for your others chips.
On detection (i.e. insmod, modprobe et al.), directories are being
created for each detected PCF8591:
-/sys/bus/devices/<0>-<1>/
+/sys/bus/i2c/devices/<0>-<1>/
where <0> is the bus the chip was detected on (e. g. i2c-0)
and <1> the chip address ([48..4f])
Inside these directories, there are such files:
-in0, in1, in2, in3, out0_enable, out0_output, name
+in0_input, in1_input, in2_input, in3_input, out0_enable, out0_output, name
Name contains chip name.
-The in0, in1, in2 and in3 files are RO. Reading gives the value of the
-corresponding channel. Depending on the current analog inputs configuration,
-files in2 and/or in3 do not exist. Values range are from 0 to 255 for single
-ended inputs and -128 to +127 for differential inputs (8-bit ADC).
+The in0_input, in1_input, in2_input and in3_input files are RO. Reading gives
+the value of the corresponding channel. Depending on the current analog inputs
+configuration, files in2_input and in3_input may not exist. Values range
+from 0 to 255 for single ended inputs and -128 to +127 for differential inputs
+(8-bit ADC).
The out0_enable file is RW. Reading gives "1" for analog output enabled and
"0" for analog output disabled. Writing accepts "0" and "1" accordingly.
diff --git a/Documentation/hwmon/tmp421 b/Documentation/hwmon/tmp421
new file mode 100644
index 00000000000..0cf07f82474
--- /dev/null
+++ b/Documentation/hwmon/tmp421
@@ -0,0 +1,36 @@
+Kernel driver tmp421
+====================
+
+Supported chips:
+ * Texas Instruments TMP421
+ Prefix: 'tmp421'
+ Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+ Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
+ * Texas Instruments TMP422
+ Prefix: 'tmp422'
+ Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+ Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
+ * Texas Instruments TMP423
+ Prefix: 'tmp423'
+ Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+ Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
+
+Authors:
+ Andre Prendel <andre.prendel@gmx.de>
+
+Description
+-----------
+
+This driver implements support for Texas Instruments TMP421, TMP422
+and TMP423 temperature sensor chips. These chips implement one local
+and up to one (TMP421), up to two (TMP422) or up to three (TMP423)
+remote sensors. Temperature is measured in degrees Celsius. The chips
+are wired over I2C/SMBus and specified over a temperature range of -40
+to +125 degrees Celsius. Resolution for both the local and remote
+channels is 0.0625 degree C.
+
+The chips support only temperature measurement. The driver exports
+the temperature values via the following sysfs files:
+
+temp[1-4]_input
+temp[2-4]_fault
diff --git a/Documentation/hwmon/wm831x b/Documentation/hwmon/wm831x
new file mode 100644
index 00000000000..24f47d8f6a4
--- /dev/null
+++ b/Documentation/hwmon/wm831x
@@ -0,0 +1,37 @@
+Kernel driver wm831x-hwmon
+==========================
+
+Supported chips:
+ * Wolfson Microelectronics WM831x PMICs
+ Prefix: 'wm831x'
+ Datasheet:
+ http://www.wolfsonmicro.com/products/WM8310
+ http://www.wolfsonmicro.com/products/WM8311
+ http://www.wolfsonmicro.com/products/WM8312
+
+Authors: Mark Brown <broonie@opensource.wolfsonmicro.com>
+
+Description
+-----------
+
+The WM831x series of PMICs include an AUXADC which can be used to
+monitor a range of system operating parameters, including the voltages
+of the major supplies within the system. Currently the driver provides
+reporting of all the input values but does not provide any alarms.
+
+Voltage Monitoring
+------------------
+
+Voltages are sampled by a 12 bit ADC. Voltages in milivolts are 1.465
+times the ADC value.
+
+Temperature Monitoring
+----------------------
+
+Temperatures are sampled by a 12 bit ADC. Chip and battery temperatures
+are available. The chip temperature is calculated as:
+
+ Degrees celsius = (512.18 - data) / 1.0983
+
+while the battery temperature calculation will depend on the NTC
+thermistor component.
diff --git a/Documentation/hwmon/wm8350 b/Documentation/hwmon/wm8350
new file mode 100644
index 00000000000..98f923bd2e9
--- /dev/null
+++ b/Documentation/hwmon/wm8350
@@ -0,0 +1,26 @@
+Kernel driver wm8350-hwmon
+==========================
+
+Supported chips:
+ * Wolfson Microelectronics WM835x PMICs
+ Prefix: 'wm8350'
+ Datasheet:
+ http://www.wolfsonmicro.com/products/WM8350
+ http://www.wolfsonmicro.com/products/WM8351
+ http://www.wolfsonmicro.com/products/WM8352
+
+Authors: Mark Brown <broonie@opensource.wolfsonmicro.com>
+
+Description
+-----------
+
+The WM835x series of PMICs include an AUXADC which can be used to
+monitor a range of system operating parameters, including the voltages
+of the major supplies within the system. Currently the driver provides
+simple access to these major supplies.
+
+Voltage Monitoring
+------------------
+
+Voltages are sampled by a 12 bit ADC. For the internal supplies the ADC
+is referenced to the system VRTC.