diff options
Diffstat (limited to 'Documentation/hwmon')
| -rw-r--r-- | Documentation/hwmon/adm1021 | 36 | ||||
| -rw-r--r-- | Documentation/hwmon/adm1275 | 60 | ||||
| -rw-r--r-- | Documentation/hwmon/coretemp | 21 | ||||
| -rw-r--r-- | Documentation/hwmon/emc6w201 | 42 | ||||
| -rw-r--r-- | Documentation/hwmon/f71882fg | 4 | ||||
| -rw-r--r-- | Documentation/hwmon/fam15h_power | 37 | ||||
| -rw-r--r-- | Documentation/hwmon/k10temp | 3 | ||||
| -rw-r--r-- | Documentation/hwmon/lm90 | 29 | ||||
| -rw-r--r-- | Documentation/hwmon/max16064 | 62 | ||||
| -rw-r--r-- | Documentation/hwmon/max16065 | 98 | ||||
| -rw-r--r-- | Documentation/hwmon/max34440 | 79 | ||||
| -rw-r--r-- | Documentation/hwmon/max6642 | 21 | ||||
| -rw-r--r-- | Documentation/hwmon/max6650 | 21 | ||||
| -rw-r--r-- | Documentation/hwmon/max8688 | 69 | ||||
| -rw-r--r-- | Documentation/hwmon/pkgtemp | 36 | ||||
| -rw-r--r-- | Documentation/hwmon/pmbus | 34 | ||||
| -rw-r--r-- | Documentation/hwmon/sht15 | 74 | ||||
| -rw-r--r-- | Documentation/hwmon/smm665 | 8 | ||||
| -rw-r--r-- | Documentation/hwmon/submitting-patches | 109 | ||||
| -rw-r--r-- | Documentation/hwmon/ucd9000 | 110 | ||||
| -rw-r--r-- | Documentation/hwmon/ucd9200 | 112 |
21 files changed, 960 insertions, 105 deletions
diff --git a/Documentation/hwmon/adm1021 b/Documentation/hwmon/adm1021 index 03d02bfb3df..02ad96cf9b2 100644 --- a/Documentation/hwmon/adm1021 +++ b/Documentation/hwmon/adm1021 @@ -14,10 +14,6 @@ Supported chips: Prefix: 'gl523sm' Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e Datasheet: - * Intel Xeon Processor - Prefix: - any other - may require 'force_adm1021' parameter - Addresses scanned: none - Datasheet: Publicly available at Intel website * Maxim MAX1617 Prefix: 'max1617' Addresses scanned: I2C 0x18 - 0x1a, 0x29 - 0x2b, 0x4c - 0x4e @@ -91,21 +87,27 @@ will do no harm, but will return 'old' values. It is possible to make ADM1021-clones do faster measurements, but there is really no good reason for that. -Xeon support ------------- -Some Xeon processors have real max1617, adm1021, or compatible chips -within them, with two temperature sensors. +Netburst-based Xeon support +--------------------------- -Other Xeons have chips with only one sensor. +Some Xeon processors based on the Netburst (early Pentium 4, from 2001 to +2003) microarchitecture had real MAX1617, ADM1021, or compatible chips +within them, with two temperature sensors. Other Xeon processors of this +era (with 400 MHz FSB) had chips with only one temperature sensor. -If you have a Xeon, and the adm1021 module loads, and both temperatures -appear valid, then things are good. +If you have such an old Xeon, and you get two valid temperatures when +loading the adm1021 module, then things are good. -If the adm1021 module doesn't load, you should try this: - modprobe adm1021 force_adm1021=BUS,ADDRESS - ADDRESS can only be 0x18, 0x1a, 0x29, 0x2b, 0x4c, or 0x4e. +If nothing happens when loading the adm1021 module, and you are certain +that your specific Xeon processor model includes compatible sensors, you +will have to explicitly instantiate the sensor chips from user-space. See +method 4 in Documentation/i2c/instantiating-devices. Possible slave +addresses are 0x18, 0x1a, 0x29, 0x2b, 0x4c, or 0x4e. It is likely that +only temp2 will be correct and temp1 will have to be ignored. -If you have dual Xeons you may have appear to have two separate -adm1021-compatible chips, or two single-temperature sensors, at distinct -addresses. +Previous generations of the Xeon processor (based on Pentium II/III) +didn't have these sensors. Next generations of Xeon processors (533 MHz +FSB and faster) lost them, until the Core-based generation which +introduced integrated digital thermal sensors. These are supported by +the coretemp driver. diff --git a/Documentation/hwmon/adm1275 b/Documentation/hwmon/adm1275 new file mode 100644 index 00000000000..6a3a6476cf2 --- /dev/null +++ b/Documentation/hwmon/adm1275 @@ -0,0 +1,60 @@ +Kernel driver adm1275 +===================== + +Supported chips: + * Analog Devices ADM1275 + Prefix: 'adm1275' + Addresses scanned: - + Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1275.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +This driver supports hardware montoring for Analog Devices ADM1275 Hot-Swap +Controller and Digital Power Monitor. + +The ADM1275 is a hot-swap controller that allows a circuit board to be removed +from or inserted into a live backplane. It also features current and voltage +readback via an integrated 12-bit analog-to-digital converter (ADC), accessed +using a PMBus. interface. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. Please see +Documentation/hwmon/pmbus for details. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in1_label "vin1" or "vout1" depending on chip variant and + configuration. +in1_input Measured voltage. From READ_VOUT register. +in1_min Minumum Voltage. From VOUT_UV_WARN_LIMIT register. +in1_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in1_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in1_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. + +curr1_label "iout1" +curr1_input Measured current. From READ_IOUT register. +curr1_max Maximum current. From IOUT_OC_WARN_LIMIT register. +curr1_max_alarm Current high alarm. From IOUT_OC_WARN_LIMIT register. diff --git a/Documentation/hwmon/coretemp b/Documentation/hwmon/coretemp index 25568f84480..f85e913a340 100644 --- a/Documentation/hwmon/coretemp +++ b/Documentation/hwmon/coretemp @@ -15,8 +15,13 @@ Author: Rudolf Marek Description ----------- +This driver permits reading the DTS (Digital Temperature Sensor) embedded +inside Intel CPUs. This driver can read both the per-core and per-package +temperature using the appropriate sensors. The per-package sensor is new; +as of now, it is present only in the SandyBridge platform. The driver will +show the temperature of all cores inside a package under a single device +directory inside hwmon. -This driver permits reading temperature sensor embedded inside Intel Core CPU. Temperature is measured in degrees Celsius and measurement resolution is 1 degree C. Valid temperatures are from 0 to TjMax degrees C, because the actual value of temperature register is in fact a delta from TjMax. @@ -27,13 +32,15 @@ mechanism will perform actions to forcibly cool down the processor. Alarm may be raised, if the temperature grows enough (more than TjMax) to trigger the Out-Of-Spec bit. Following table summarizes the exported sysfs files: -temp1_input - Core temperature (in millidegrees Celsius). -temp1_max - All cooling devices should be turned on (on Core2). -temp1_crit - Maximum junction temperature (in millidegrees Celsius). -temp1_crit_alarm - Set when Out-of-spec bit is set, never clears. +All Sysfs entries are named with their core_id (represented here by 'X'). +tempX_input - Core temperature (in millidegrees Celsius). +tempX_max - All cooling devices should be turned on (on Core2). +tempX_crit - Maximum junction temperature (in millidegrees Celsius). +tempX_crit_alarm - Set when Out-of-spec bit is set, never clears. Correct CPU operation is no longer guaranteed. -temp1_label - Contains string "Core X", where X is processor - number. +tempX_label - Contains string "Core X", where X is processor + number. For Package temp, this will be "Physical id Y", + where Y is the package number. The TjMax temperature is set to 85 degrees C if undocumented model specific register (UMSR) 0xee has bit 30 set. If not the TjMax is 100 degrees C as diff --git a/Documentation/hwmon/emc6w201 b/Documentation/hwmon/emc6w201 new file mode 100644 index 00000000000..32f355aaf56 --- /dev/null +++ b/Documentation/hwmon/emc6w201 @@ -0,0 +1,42 @@ +Kernel driver emc6w201 +====================== + +Supported chips: + * SMSC EMC6W201 + Prefix: 'emc6w201' + Addresses scanned: I2C 0x2c, 0x2d, 0x2e + Datasheet: Not public + +Author: Jean Delvare <khali@linux-fr.org> + + +Description +----------- + +From the datasheet: + +"The EMC6W201 is an environmental monitoring device with automatic fan +control capability and enhanced system acoustics for noise suppression. +This ACPI compliant device provides hardware monitoring for up to six +voltages (including its own VCC) and five external thermal sensors, +measures the speed of up to five fans, and controls the speed of +multiple DC fans using three Pulse Width Modulator (PWM) outputs. Note +that it is possible to control more than three fans by connecting two +fans to one PWM output. The EMC6W201 will be available in a 36-pin +QFN package." + +The device is functionally close to the EMC6D100 series, but is +register-incompatible. + +The driver currently only supports the monitoring of the voltages, +temperatures and fan speeds. Limits can be changed. Alarms are not +supported, and neither is fan speed control. + + +Known Systems With EMC6W201 +--------------------------- + +The EMC6W201 is a rare device, only found on a few systems, made in +2005 and 2006. Known systems with this device: +* Dell Precision 670 workstation +* Gigabyte 2CEWH mainboard diff --git a/Documentation/hwmon/f71882fg b/Documentation/hwmon/f71882fg index df02245d141..84d2623810f 100644 --- a/Documentation/hwmon/f71882fg +++ b/Documentation/hwmon/f71882fg @@ -6,6 +6,10 @@ Supported chips: Prefix: 'f71808e' Addresses scanned: none, address read from Super I/O config space Datasheet: Not public + * Fintek F71808A + Prefix: 'f71808a' + Addresses scanned: none, address read from Super I/O config space + Datasheet: Not public * Fintek F71858FG Prefix: 'f71858fg' Addresses scanned: none, address read from Super I/O config space diff --git a/Documentation/hwmon/fam15h_power b/Documentation/hwmon/fam15h_power new file mode 100644 index 00000000000..a92918e0bd6 --- /dev/null +++ b/Documentation/hwmon/fam15h_power @@ -0,0 +1,37 @@ +Kernel driver fam15h_power +========================== + +Supported chips: +* AMD Family 15h Processors + + Prefix: 'fam15h_power' + Addresses scanned: PCI space + Datasheets: + BIOS and Kernel Developer's Guide (BKDG) For AMD Family 15h Processors + (not yet published) + +Author: Andreas Herrmann <andreas.herrmann3@amd.com> + +Description +----------- + +This driver permits reading of registers providing power information +of AMD Family 15h processors. + +For AMD Family 15h processors the following power values can be +calculated using different processor northbridge function registers: + +* BasePwrWatts: Specifies in watts the maximum amount of power + consumed by the processor for NB and logic external to the core. +* ProcessorPwrWatts: Specifies in watts the maximum amount of power + the processor can support. +* CurrPwrWatts: Specifies in watts the current amount of power being + consumed by the processor. + +This driver provides ProcessorPwrWatts and CurrPwrWatts: +* power1_crit (ProcessorPwrWatts) +* power1_input (CurrPwrWatts) + +On multi-node processors the calculated value is for the entire +package and not for a single node. Thus the driver creates sysfs +attributes only for internal node0 of a multi-node processor. diff --git a/Documentation/hwmon/k10temp b/Documentation/hwmon/k10temp index d2b56a4fd1f..0393c89277c 100644 --- a/Documentation/hwmon/k10temp +++ b/Documentation/hwmon/k10temp @@ -11,6 +11,7 @@ Supported chips: Socket S1G2: Athlon (X2), Sempron (X2), Turion X2 (Ultra) * AMD Family 12h processors: "Llano" * AMD Family 14h processors: "Brazos" (C/E/G-Series) +* AMD Family 15h processors: "Bulldozer" Prefix: 'k10temp' Addresses scanned: PCI space @@ -40,7 +41,7 @@ Description ----------- This driver permits reading of the internal temperature sensor of AMD -Family 10h/11h/12h/14h processors. +Family 10h/11h/12h/14h/15h processors. All these processors have a sensor, but on those for Socket F or AM2+, the sensor may return inconsistent values (erratum 319). The driver diff --git a/Documentation/hwmon/lm90 b/Documentation/hwmon/lm90 index fa475c0a48a..f3efd18e87f 100644 --- a/Documentation/hwmon/lm90 +++ b/Documentation/hwmon/lm90 @@ -32,6 +32,16 @@ Supported chips: Addresses scanned: I2C 0x4c and 0x4d Datasheet: Publicly available at the ON Semiconductor website http://www.onsemi.com/PowerSolutions/product.do?id=ADT7461 + * Analog Devices ADT7461A + Prefix: 'adt7461a' + Addresses scanned: I2C 0x4c and 0x4d + Datasheet: Publicly available at the ON Semiconductor website + http://www.onsemi.com/PowerSolutions/product.do?id=ADT7461A + * ON Semiconductor NCT1008 + Prefix: 'nct1008' + Addresses scanned: I2C 0x4c and 0x4d + Datasheet: Publicly available at the ON Semiconductor website + http://www.onsemi.com/PowerSolutions/product.do?id=NCT1008 * Maxim MAX6646 Prefix: 'max6646' Addresses scanned: I2C 0x4d @@ -149,7 +159,7 @@ ADM1032: * ALERT is triggered by open remote sensor. * SMBus PEC support for Write Byte and Receive Byte transactions. -ADT7461: +ADT7461, ADT7461A, NCT1008: * Extended temperature range (breaks compatibility) * Lower resolution for remote temperature @@ -195,9 +205,9 @@ are exported, one for each channel, but these values are of course linked. Only the local hysteresis can be set from user-space, and the same delta applies to the remote hysteresis. -The lm90 driver will not update its values more frequently than every -other second; reading them more often will do no harm, but will return -'old' values. +The lm90 driver will not update its values more frequently than configured with +the update_interval attribute; reading them more often will do no harm, but will +return 'old' values. SMBus Alert Support ------------------- @@ -205,11 +215,12 @@ SMBus Alert Support This driver has basic support for SMBus alert. When an alert is received, the status register is read and the faulty temperature channel is logged. -The Analog Devices chips (ADM1032 and ADT7461) do not implement the SMBus -alert protocol properly so additional care is needed: the ALERT output is -disabled when an alert is received, and is re-enabled only when the alarm -is gone. Otherwise the chip would block alerts from other chips in the bus -as long as the alarm is active. +The Analog Devices chips (ADM1032, ADT7461 and ADT7461A) and ON +Semiconductor chips (NCT1008) do not implement the SMBus alert protocol +properly so additional care is needed: the ALERT output is disabled when +an alert is received, and is re-enabled only when the alarm is gone. +Otherwise the chip would block alerts from other chips in the bus as long +as the alarm is active. PEC Support ----------- diff --git a/Documentation/hwmon/max16064 b/Documentation/hwmon/max16064 new file mode 100644 index 00000000000..41728999e14 --- /dev/null +++ b/Documentation/hwmon/max16064 @@ -0,0 +1,62 @@ +Kernel driver max16064 +====================== + +Supported chips: + * Maxim MAX16064 + Prefix: 'max16064' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX16064.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX16064 Quad Power-Supply +Controller with Active-Voltage Output Control and PMBus Interface. + +The driver is a client driver to the core PMBus driver. +Please see Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in[1-4]_label "vout[1-4]" +in[1-4]_input Measured voltage. From READ_VOUT register. +in[1-4]_min Minumum Voltage. From VOUT_UV_WARN_LIMIT register. +in[1-4]_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in[1-4]_lcrit Critical minumum Voltage. VOUT_UV_FAULT_LIMIT register. +in[1-4]_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in[1-4]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in[1-4]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in[1-4]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in[1-4]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. + +temp1_input Measured temperature. From READ_TEMPERATURE_1 register. +temp1_max Maximum temperature. From OT_WARN_LIMIT register. +temp1_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp1_max_alarm Chip temperature high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_WARN_LIMIT if TEMP_OT_WARNING + status is set. +temp1_crit_alarm Chip temperature critical high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_FAULT_LIMIT if TEMP_OT_FAULT + status is set. diff --git a/Documentation/hwmon/max16065 b/Documentation/hwmon/max16065 new file mode 100644 index 00000000000..44b4f61e04f --- /dev/null +++ b/Documentation/hwmon/max16065 @@ -0,0 +1,98 @@ +Kernel driver max16065 +====================== + +Supported chips: + * Maxim MAX16065, MAX16066 + Prefixes: 'max16065', 'max16066' + Addresses scanned: - + Datasheet: + http://datasheets.maxim-ic.com/en/ds/MAX16065-MAX16066.pdf + * Maxim MAX16067 + Prefix: 'max16067' + Addresses scanned: - + Datasheet: + http://datasheets.maxim-ic.com/en/ds/MAX16067.pdf + * Maxim MAX16068 + Prefix: 'max16068' + Addresses scanned: - + Datasheet: + http://datasheets.maxim-ic.com/en/ds/MAX16068.pdf + * Maxim MAX16070/MAX16071 + Prefixes: 'max16070', 'max16071' + Addresses scanned: - + Datasheet: + http://datasheets.maxim-ic.com/en/ds/MAX16070-MAX16071.pdf + + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +[From datasheets] The MAX16065/MAX16066 flash-configurable system managers +monitor and sequence multiple system voltages. The MAX16065/MAX16066 can also +accurately monitor (+/-2.5%) one current channel using a dedicated high-side +current-sense amplifier. The MAX16065 manages up to twelve system voltages +simultaneously, and the MAX16066 manages up to eight supply voltages. + +The MAX16067 flash-configurable system manager monitors and sequences multiple +system voltages. The MAX16067 manages up to six system voltages simultaneously. + +The MAX16068 flash-configurable system manager monitors and manages up to six +system voltages simultaneously. + +The MAX16070/MAX16071 flash-configurable system monitors supervise multiple +system voltages. The MAX16070/MAX16071 can also accurately monitor (+/-2.5%) +one current channel using a dedicated high-side current-sense amplifier. The +MAX16070 monitors up to twelve system voltages simultaneously, and the MAX16071 +monitors up to eight supply voltages. + +Each monitored channel has its own low and high critical limits. MAX16065, +MAX16066, MAX16070, and MAX16071 support an additional limit which is +configurable as either low or high secondary limit. MAX16065, MAX16066, +MAX16070, and MAX16071 also support supply current monitoring. + + +Usage Notes +----------- + +This driver does not probe for devices, since there is no register which +can be safely used to identify the chip. You will have to instantiate +the devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Sysfs entries +------------- + +in[0-11]_input Input voltage measurements. + +in12_input Voltage on CSP (Current Sense Positive) pin. + Only if the chip supports current sensing and if + current sensing is enabled. + +in[0-11]_min Low warning limit. + Supported on MAX16065, MAX16066, MAX16070, and MAX16071 + only. + +in[0-11]_max High warning limit. + Supported on MAX16065, MAX16066, MAX16070, and MAX16071 + only. + + Either low or high warning limits are supported + (depending on chip configuration), but not both. + +in[0-11]_lcrit Low critical limit. + +in[0-11]_crit High critical limit. + +in[0-11]_alarm Input voltage alarm. + +curr1_input Current sense input; only if the chip supports current + sensing and if current sensing is enabled. + Displayed current assumes 0.001 Ohm current sense + resistor. + +curr1_alarm Overcurrent alarm; only if the chip supports current + sensing and if current sensing is enabled. diff --git a/Documentation/hwmon/max34440 b/Documentation/hwmon/max34440 new file mode 100644 index 00000000000..6c525dd07d5 --- /dev/null +++ b/Documentation/hwmon/max34440 @@ -0,0 +1,79 @@ +Kernel driver max34440 +====================== + +Supported chips: + * Maxim MAX34440 + Prefixes: 'max34440' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34440.pdf + * Maxim MAX34441 + PMBus 5-Channel Power-Supply Manager and Intelligent Fan Controller + Prefixes: 'max34441' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34441.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX34440 PMBus 6-Channel +Power-Supply Manager and MAX34441 PMBus 5-Channel Power-Supply Manager +and Intelligent Fan Controller. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in[1-6]_label "vout[1-6]". +in[1-6]_input Measured voltage. From READ_VOUT register. +in[1-6]_min Minumum Voltage. From VOUT_UV_WARN_LIMIT register. +in[1-6]_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in[1-6]_lcrit Critical minumum Voltage. VOUT_UV_FAULT_LIMIT register. +in[1-6]_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in[1-6]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in[1-6]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in[1-6]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in[1-6]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. + +curr[1-6]_label "iout[1-6]". +curr[1-6]_input Measured current. From READ_IOUT register. +curr[1-6]_max Maximum current. From IOUT_OC_WARN_LIMIT register. +curr[1-6]_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. +curr[1-6]_max_alarm Current high alarm. From IOUT_OC_WARNING status. +curr[1-6]_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. + + in6 and curr6 attributes only exist for MAX34440. + +temp[1-8]_input Measured temperatures. From READ_TEMPERATURE_1 register. + temp1 is the chip's internal temperature. temp2..temp5 + are remote I2C temperature sensors. For MAX34441, temp6 + is a remote thermal-diode sensor. For MAX34440, temp6..8 + are remote I2C temperature sensors. +temp[1-8]_max Maximum temperature. From OT_WARN_LIMIT register. +temp[1-8]_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp[1-8]_max_alarm Temperature high alarm. +temp[1-8]_crit_alarm Temperature critical high alarm. + + temp7 and temp8 attributes only exist for MAX34440. diff --git a/Documentation/hwmon/max6642 b/Documentation/hwmon/max6642 new file mode 100644 index 00000000000..afbd3e4942e --- /dev/null +++ b/Documentation/hwmon/max6642 @@ -0,0 +1,21 @@ +Kernel driver max6642 +===================== + +Supported chips: + * Maxim MAX6642 + Prefix: 'max6642' + Addresses scanned: I2C 0x48-0x4f + Datasheet: Publicly available at the Maxim website + http://datasheets.maxim-ic.com/en/ds/MAX6642.pdf + +Authors: + Per Dalen <per.dalen@appeartv.com> + +Description +----------- + +The MAX6642 is a digital temperature sensor. It senses its own temperature as +well as the temperature on one external diode. + +All temperature values are given in degrees Celsius. Resolution +is 0.25 degree for the local temperature and for the remote temperature. diff --git a/Documentation/hwmon/max6650 b/Documentation/hwmon/max6650 index c565650fcfc..58d9644a2bd 100644 --- a/Documentation/hwmon/max6650 +++ b/Documentation/hwmon/max6650 @@ -2,9 +2,13 @@ Kernel driver max6650 ===================== Supported chips: - * Maxim 6650 / 6651 + * Maxim MAX6650 Prefix: 'max6650' - Addresses scanned: I2C 0x1b, 0x1f, 0x48, 0x4b + Addresses scanned: none + Datasheet: http://pdfserv.maxim-ic.com/en/ds/MAX6650-MAX6651.pdf + * Maxim MAX6651 + Prefix: 'max6651' + Addresses scanned: none Datasheet: http://pdfserv.maxim-ic.com/en/ds/MAX6650-MAX6651.pdf Authors: @@ -15,10 +19,10 @@ Authors: Description ----------- -This driver implements support for the Maxim 6650/6651 +This driver implements support for the Maxim MAX6650 and MAX6651. -The 2 devices are very similar, but the Maxim 6550 has a reduced feature -set, e.g. only one fan-input, instead of 4 for the 6651. +The 2 devices are very similar, but the MAX6550 has a reduced feature +set, e.g. only one fan-input, instead of 4 for the MAX6651. The driver is not able to distinguish between the 2 devices. @@ -36,6 +40,13 @@ fan1_div rw sets the speed range the inputs can handle. Legal values are 1, 2, 4, and 8. Use lower values for faster fans. +Usage notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + Module parameters ----------------- diff --git a/Documentation/hwmon/max8688 b/Documentation/hwmon/max8688 new file mode 100644 index 00000000000..0ddd3a41203 --- /dev/null +++ b/Documentation/hwmon/max8688 @@ -0,0 +1,69 @@ +Kernel driver max8688 +===================== + +Supported chips: + * Maxim MAX8688 + Prefix: 'max8688' + Addresses scanned: - + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX8688.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +This driver supports hardware montoring for Maxim MAX8688 Digital Power-Supply +Controller/Monitor with PMBus Interface. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in1_label "vout1" +in1_input Measured voltage. From READ_VOUT register. +in1_min Minumum Voltage. From VOUT_UV_WARN_LIMIT register. +in1_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. +in1_lcrit Critical minumum Voltage. VOUT_UV_FAULT_LIMIT register. +in1_crit Critical maximum voltage. From VOUT_OV_FAULT_LIMIT register. +in1_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. +in1_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in1_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. +in1_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. + +curr1_label "iout1" +curr1_input Measured current. From READ_IOUT register. +curr1_max Maximum current. From IOUT_OC_WARN_LIMIT register. +curr1_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. +curr1_max_alarm Current high alarm. From IOUT_OC_WARN_LIMIT register. +curr1_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. + +temp1_input Measured temperature. From READ_TEMPERATURE_1 register. +temp1_max Maximum temperature. From OT_WARN_LIMIT register. +temp1_crit Critical high temperature. From OT_FAULT_LIMIT register. +temp1_max_alarm Chip temperature high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_WARN_LIMIT if TEMP_OT_WARNING + status is set. +temp1_crit_alarm Chip temperature critical high alarm. Set by comparing + READ_TEMPERATURE_1 with OT_FAULT_LIMIT if TEMP_OT_FAULT + status is set. diff --git a/Documentation/hwmon/pkgtemp b/Documentation/hwmon/pkgtemp deleted file mode 100644 index c8e1fb0fadd..00000000000 --- a/Documentation/hwmon/pkgtemp +++ /dev/null @@ -1,36 +0,0 @@ -Kernel driver pkgtemp -====================== - -Supported chips: - * Intel family - Prefix: 'pkgtemp' - CPUID: - Datasheet: Intel 64 and IA-32 Architectures Software Developer's Manual - Volume 3A: System Programming Guide - -Author: Fenghua Yu - -Description ------------ - -This driver permits reading package level temperature sensor embedded inside -Intel CPU package. The sensors can be in core, uncore, memory controller, or -other components in a package. The feature is first implemented in Intel Sandy -Bridge platform. - -Temperature is measured in degrees Celsius and measurement resolution is -1 degree C. Valid temperatures are from 0 to TjMax degrees C, because the actual -value of temperature register is in fact a delta from TjMax. - -Temperature known as TjMax is the maximum junction temperature of package. -We get this from MSR_IA32_TEMPERATURE_TARGET. If the MSR is not accessible, -we define TjMax as 100 degrees Celsius. At this temperature, protection -mechanism will perform actions to forcibly cool down the package. Alarm -may be raised, if the temperature grows enough (more than TjMax) to trigger -the Out-Of-Spec bit. Following table summarizes the exported sysfs files: - -temp1_input - Package temperature (in millidegrees Celsius). -temp1_max - All cooling devices should be turned on. -temp1_crit - Maximum junction temperature (in millidegrees Celsius). -temp1_crit_alarm - Set when Out-of-spec bit is set, never clears. - Correct CPU operation is no longer guaranteed. diff --git a/Documentation/hwmon/pmbus b/Documentation/hwmon/pmbus index dc4933e9634..5e462fc7f99 100644 --- a/Documentation/hwmon/pmbus +++ b/Documentation/hwmon/pmbus @@ -13,26 +13,6 @@ Supported chips: Prefix: 'ltc2978' Addresses scanned: - Datasheet: http://cds.linear.com/docs/Datasheet/2978fa.pdf - * Maxim MAX16064 - Quad Power-Supply Controller - Prefix: 'max16064' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX16064.pdf - * Maxim MAX34440 - PMBus 6-Channel Power-Supply Manager - Prefixes: 'max34440' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34440.pdf - * Maxim MAX34441 - PMBus 5-Channel Power-Supply Manager and Intelligent Fan Controller - Prefixes: 'max34441' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX34441.pdf - * Maxim MAX8688 - Digital Power-Supply Controller/Monitor - Prefix: 'max8688' - Addresses scanned: - - Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX8688.pdf * Generic PMBus devices Prefix: 'pmbus' Addresses scanned: - @@ -175,11 +155,13 @@ currX_crit Critical maximum current. From IIN_OC_FAULT_LIMIT or IOUT_OC_FAULT_LIMIT register. currX_alarm Current high alarm. From IIN_OC_WARNING or IOUT_OC_WARNING status. +currX_max_alarm Current high alarm. + From IIN_OC_WARN_LIMIT or IOUT_OC_WARN_LIMIT status. currX_lcrit_alarm Output current critical low alarm. From IOUT_UC_FAULT status. currX_crit_alarm Current critical high alarm. From IIN_OC_FAULT or IOUT_OC_FAULT status. -currX_label "iin" or "vinY" +currX_label "iin" or "ioutY" powerX_input Measured power. From READ_PIN or READ_POUT register. powerX_cap Output |