diff options
Diffstat (limited to 'Documentation/hwmon/w83627ehf')
| -rw-r--r-- | Documentation/hwmon/w83627ehf | 60 |
1 files changed, 44 insertions, 16 deletions
diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf index 13d556112fc..76ffef94ed7 100644 --- a/Documentation/hwmon/w83627ehf +++ b/Documentation/hwmon/w83627ehf @@ -5,13 +5,11 @@ Supported chips: * Winbond W83627EHF/EHG (ISA access ONLY) Prefix: 'w83627ehf' Addresses scanned: ISA address retrieved from Super I/O registers - Datasheet: - http://www.nuvoton.com.tw/NR/rdonlyres/A6A258F0-F0C9-4F97-81C0-C4D29E7E943E/0/W83627EHF.pdf + Datasheet: not available * Winbond W83627DHG Prefix: 'w83627dhg' Addresses scanned: ISA address retrieved from Super I/O registers - Datasheet: - http://www.nuvoton.com.tw/NR/rdonlyres/7885623D-A487-4CF9-A47F-30C5F73D6FE6/0/W83627DHG.pdf + Datasheet: not available * Winbond W83627DHG-P Prefix: 'w83627dhg' Addresses scanned: ISA address retrieved from Super I/O registers @@ -24,6 +22,14 @@ Supported chips: Prefix: 'w83667hg' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: Available from Nuvoton upon request + * Nuvoton NCT6775F/W83667HG-I + Prefix: 'nct6775' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request + * Nuvoton NCT6776F + Prefix: 'nct6776' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request Authors: Jean Delvare <khali@linux-fr.org> @@ -36,19 +42,28 @@ Description ----------- This driver implements support for the Winbond W83627EHF, W83627EHG, -W83627DHG, W83627DHG-P, W83667HG and W83667HG-B super I/O chips. -We will refer to them collectively as Winbond chips. - -The chips implement three temperature sensors, five fan rotation -speed sensors, ten analog voltage sensors (only nine for the 627DHG), one -VID (6 pins for the 627EHF/EHG, 8 pins for the 627DHG and 667HG), alarms -with beep warnings (control unimplemented), and some automatic fan -regulation strategies (plus manual fan control mode). +W83627DHG, W83627DHG-P, W83667HG, W83667HG-B, W83667HG-I (NCT6775F), +and NCT6776F super I/O chips. We will refer to them collectively as +Winbond chips. + +The chips implement three temperature sensors (up to four for 667HG-B, and nine +for NCT6775F and NCT6776F), five fan rotation speed sensors, ten analog voltage +sensors (only nine for the 627DHG), one VID (6 pins for the 627EHF/EHG, 8 pins +for the 627DHG and 667HG), alarms with beep warnings (control unimplemented), +and some automatic fan regulation strategies (plus manual fan control mode). + +The temperature sensor sources on W82677HG-B, NCT6775F, and NCT6776F are +configurable. temp4 and higher attributes are only reported if its temperature +source differs from the temperature sources of the already reported temperature +sensors. The configured source for each of the temperature sensors is provided +in tempX_label. Temperatures are measured in degrees Celsius and measurement resolution is 1 -degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when -the temperature gets higher than high limit; it stays on until the temperature -falls below the hysteresis value. +degC for temp1 and and 0.5 degC for temp2 and temp3. For temp4 and higher, +resolution is 1 degC for W83667HG-B and 0.0 degC for NCT6775F and NCT6776F. +An alarm is triggered when the temperature gets higher than high limit; +it stays on until the temperature falls below the hysteresis value. +Alarms are only supported for temp1, temp2, and temp3. Fan rotation speeds are reported in RPM (rotations per minute). An alarm is triggered if the rotation speed has dropped below a programmable limit. Fan @@ -80,7 +95,8 @@ prog -> pwm4 (not on 667HG and 667HG-B; the programmable setting is not name - this is a standard hwmon device entry. For the W83627EHF and W83627EHG, it is set to "w83627ehf", for the W83627DHG it is set to "w83627dhg", - and for the W83667HG it is set to "w83667hg". + for the W83667HG and W83667HG-B it is set to "w83667hg", for NCT6775F it + is set to "nct6775", and for NCT6776F it is set to "nct6776". pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range: 0 (stop) to 255 (full) @@ -90,6 +106,18 @@ pwm[1-4]_enable - this file controls mode of fan/temperature control: * 2 "Thermal Cruise" mode * 3 "Fan Speed Cruise" mode * 4 "Smart Fan III" mode + * 5 "Smart Fan IV" mode + + SmartFan III mode is not supported on NCT6776F. + + SmartFan IV mode is configurable only if it was configured at system + startup, and is only supported for W83677HG-B, NCT6775F, and NCT6776F. + SmartFan IV operational parameters can not be configured at this time, + and the various pwm attributes are not used in SmartFan IV mode. + The attributes can be written to, which is useful if you plan to + configure the system for a different pwm mode. However, the information + returned when reading pwm attributes is unrelated to SmartFan IV + operation. pwm[1-4]_mode - controls if output is PWM or DC level * 0 DC output (0 - 12v) |