diff options
Diffstat (limited to 'Documentation/filesystems')
| -rw-r--r-- | Documentation/filesystems/proc.txt | 12 | ||||
| -rw-r--r-- | Documentation/filesystems/ubifs.txt | 26 |
2 files changed, 11 insertions, 27 deletions
diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt index b0b814d75ca..f4817802406 100644 --- a/Documentation/filesystems/proc.txt +++ b/Documentation/filesystems/proc.txt @@ -574,6 +574,12 @@ The contents of each smp_affinity file is the same by default: > cat /proc/irq/0/smp_affinity ffffffff +There is an alternate interface, smp_affinity_list which allows specifying +a cpu range instead of a bitmask: + + > cat /proc/irq/0/smp_affinity_list + 1024-1031 + The default_smp_affinity mask applies to all non-active IRQs, which are the IRQs which have not yet been allocated/activated, and hence which lack a /proc/irq/[0-9]* directory. @@ -583,12 +589,13 @@ reports itself as being attached. This hardware locality information does not include information about any possible driver locality preference. prof_cpu_mask specifies which CPUs are to be profiled by the system wide -profiler. Default value is ffffffff (all cpus). +profiler. Default value is ffffffff (all cpus if there are only 32 of them). The way IRQs are routed is handled by the IO-APIC, and it's Round Robin between all the CPUs which are allowed to handle it. As usual the kernel has more info than you and does a better job than you, so the defaults are the -best choice for almost everyone. +best choice for almost everyone. [Note this applies only to those IO-APIC's +that support "Round Robin" interrupt distribution.] There are three more important subdirectories in /proc: net, scsi, and sys. The general rule is that the contents, or even the existence of these @@ -836,7 +843,6 @@ Provides counts of softirq handlers serviced since boot time, for each cpu. TASKLET: 0 0 0 290 SCHED: 27035 26983 26971 26746 HRTIMER: 0 0 0 0 - RCU: 1678 1769 2178 2250 1.3 IDE devices in /proc/ide diff --git a/Documentation/filesystems/ubifs.txt b/Documentation/filesystems/ubifs.txt index d7b13b01e98..8e4fab639d9 100644 --- a/Documentation/filesystems/ubifs.txt +++ b/Documentation/filesystems/ubifs.txt @@ -115,28 +115,8 @@ ubi.mtd=0 root=ubi0:rootfs rootfstype=ubifs Module Parameters for Debugging =============================== -When UBIFS has been compiled with debugging enabled, there are 3 module +When UBIFS has been compiled with debugging enabled, there are 2 module parameters that are available to control aspects of testing and debugging. -The parameters are unsigned integers where each bit controls an option. -The parameters are: - -debug_msgs Selects which debug messages to display, as follows: - - Message Type Flag value - - General messages 1 - Journal messages 2 - Mount messages 4 - Commit messages 8 - LEB search messages 16 - Budgeting messages 32 - Garbage collection messages 64 - Tree Node Cache (TNC) messages 128 - LEB properties (lprops) messages 256 - Input/output messages 512 - Log messages 1024 - Scan messages 2048 - Recovery messages 4096 debug_chks Selects extra checks that UBIFS can do while running: @@ -154,11 +134,9 @@ debug_tsts Selects a mode of testing, as follows: Test mode Flag value - Force in-the-gaps method 2 Failure mode for recovery testing 4 -For example, set debug_msgs to 5 to display General messages and Mount -messages. +For example, set debug_chks to 3 to enable general and TNC checks. References |