diff options
Diffstat (limited to 'Documentation/devicetree')
-rw-r--r-- | Documentation/devicetree/bindings/arm/pmu.txt | 21 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/arm/primecell.txt | 21 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/crypto/fsl-sec2.txt (renamed from Documentation/devicetree/bindings/powerpc/fsl/sec.txt) | 2 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt | 22 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/gpio/gpio.txt | 46 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/gpio/gpio_nvidia.txt | 8 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt | 22 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/spi/spi_nvidia.txt | 5 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/tty/serial/of-serial.txt | 36 |
9 files changed, 173 insertions, 10 deletions
diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt new file mode 100644 index 00000000000..1c044eb320c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -0,0 +1,21 @@ +* ARM Performance Monitor Units + +ARM cores often have a PMU for counting cpu and cache events like cache misses +and hits. The interface to the PMU is part of the ARM ARM. The ARM PMU +representation in the device tree should be done as under:- + +Required properties: + +- compatible : should be one of + "arm,cortex-a9-pmu" + "arm,cortex-a8-pmu" + "arm,arm1176-pmu" + "arm,arm1136-pmu" +- interrupts : 1 combined interrupt or 1 per core. + +Example: + +pmu { + compatible = "arm,cortex-a9-pmu"; + interrupts = <100 101>; +}; diff --git a/Documentation/devicetree/bindings/arm/primecell.txt b/Documentation/devicetree/bindings/arm/primecell.txt new file mode 100644 index 00000000000..1d5d7a870ec --- /dev/null +++ b/Documentation/devicetree/bindings/arm/primecell.txt @@ -0,0 +1,21 @@ +* ARM Primecell Peripherals + +ARM, Ltd. Primecell peripherals have a standard id register that can be used to +identify the peripheral type, vendor, and revision. This value can be used for +driver matching. + +Required properties: + +- compatible : should be a specific value for peripheral and "arm,primecell" + +Optional properties: + +- arm,primecell-periphid : Value to override the h/w value with + +Example: + +serial@fff36000 { + compatible = "arm,pl011", "arm,primecell"; + arm,primecell-periphid = <0x00341011>; +}; + diff --git a/Documentation/devicetree/bindings/powerpc/fsl/sec.txt b/Documentation/devicetree/bindings/crypto/fsl-sec2.txt index 2b6f2d45c45..38988ef1336 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/sec.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec2.txt @@ -1,4 +1,4 @@ -Freescale SoC SEC Security Engines +Freescale SoC SEC Security Engines versions 2.x-3.x Required properties: diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt new file mode 100644 index 00000000000..4363ae4b3c1 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt @@ -0,0 +1,22 @@ +* Freescale i.MX/MXC GPIO controller + +Required properties: +- compatible : Should be "fsl,<soc>-gpio" +- reg : Address and length of the register set for the device +- interrupts : Should be the port interrupt shared by all 32 pins, if + one number. If two numbers, the first one is the interrupt shared + by low 16 pins and the second one is for high 16 pins. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). + +Example: + +gpio0: gpio@73f84000 { + compatible = "fsl,imx51-gpio", "fsl,imx31-gpio"; + reg = <0x73f84000 0x4000>; + interrupts = <50 51>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index edaa84d288a..4e16ba4feab 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -4,17 +4,45 @@ Specifying GPIO information for devices 1) gpios property ----------------- -Nodes that makes use of GPIOs should define them using `gpios' property, -format of which is: <&gpio-controller1-phandle gpio1-specifier - &gpio-controller2-phandle gpio2-specifier - 0 /* holes are permitted, means no GPIO 3 */ - &gpio-controller4-phandle gpio4-specifier - ...>; +Nodes that makes use of GPIOs should specify them using one or more +properties, each containing a 'gpio-list': -Note that gpio-specifier length is controller dependent. + gpio-list ::= <single-gpio> [gpio-list] + single-gpio ::= <gpio-phandle> <gpio-specifier> + gpio-phandle : phandle to gpio controller node + gpio-specifier : Array of #gpio-cells specifying specific gpio + (controller specific) + +GPIO properties should be named "[<name>-]gpios". Exact +meaning of each gpios property must be documented in the device tree +binding for each device. + +For example, the following could be used to describe gpios pins to use +as chip select lines; with chip selects 0, 1 and 3 populated, and chip +select 2 left empty: + + gpio1: gpio1 { + gpio-controller + #gpio-cells = <2>; + }; + gpio2: gpio2 { + gpio-controller + #gpio-cells = <1>; + }; + [...] + chipsel-gpios = <&gpio1 12 0>, + <&gpio1 13 0>, + <0>, /* holes are permitted, means no GPIO 2 */ + <&gpio2 2>; + +Note that gpio-specifier length is controller dependent. In the +above example, &gpio1 uses 2 cells to specify a gpio, while &gpio2 +only uses one. gpio-specifier may encode: bank, pin position inside the bank, whether pin is open-drain and whether pin is logically inverted. +Exact meaning of each specifier cell is controller specific, and must +be documented in the device tree binding for the device. Example of the node using GPIOs: @@ -28,8 +56,8 @@ and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller. 2) gpio-controller nodes ------------------------ -Every GPIO controller node must have #gpio-cells property defined, -this information will be used to translate gpio-specifiers. +Every GPIO controller node must both an empty "gpio-controller" +property, and have #gpio-cells contain the size of the gpio-specifier. Example of two SOC GPIO banks defined as gpio-controller nodes: diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt new file mode 100644 index 00000000000..eb4b530d64e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt @@ -0,0 +1,8 @@ +NVIDIA Tegra 2 GPIO controller + +Required properties: +- compatible : "nvidia,tegra20-gpio" +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- gpio-controller : Marks the device node as a GPIO controller. diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt new file mode 100644 index 00000000000..9841057d112 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -0,0 +1,22 @@ +* Freescale (Enhanced) Configurable Serial Peripheral Interface + (CSPI/eCSPI) for i.MX + +Required properties: +- compatible : Should be "fsl,<soc>-cspi" or "fsl,<soc>-ecspi" +- reg : Offset and length of the register set for the device +- interrupts : Should contain CSPI/eCSPI interrupt +- fsl,spi-num-chipselects : Contains the number of the chipselect +- cs-gpios : Specifies the gpio pins to be used for chipselects. + +Example: + +ecspi@70010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx51-ecspi"; + reg = <0x70010000 0x4000>; + interrupts = <36>; + fsl,spi-num-chipselects = <2>; + cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */ + <&gpio3 25 0>; /* GPIO4_25 */ +}; diff --git a/Documentation/devicetree/bindings/spi/spi_nvidia.txt b/Documentation/devicetree/bindings/spi/spi_nvidia.txt new file mode 100644 index 00000000000..6b9e5189669 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_nvidia.txt @@ -0,0 +1,5 @@ +NVIDIA Tegra 2 SPI device + +Required properties: +- compatible : should be "nvidia,tegra20-spi". +- gpios : should specify GPIOs used for chipselect. diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt new file mode 100644 index 00000000000..b8b27b0aca1 --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt @@ -0,0 +1,36 @@ +* UART (Universal Asynchronous Receiver/Transmitter) + +Required properties: +- compatible : one of: + - "ns8250" + - "ns16450" + - "ns16550a" + - "ns16550" + - "ns16750" + - "ns16850" + - "nvidia,tegra20-uart" + - "ibm,qpace-nwp-serial" + - "serial" if the port type is unknown. +- reg : offset and length of the register set for the device. +- interrupts : should contain uart interrupt. +- clock-frequency : the input clock frequency for the UART. + +Optional properties: +- current-speed : the current active speed of the UART. +- reg-offset : offset to apply to the mapbase from the start of the registers. +- reg-shift : quantity to shift the register offsets by. +- reg-io-width : the size (in bytes) of the IO accesses that should be + performed on the device. There are some systems that require 32-bit + accesses to the UART (e.g. TI davinci). +- used-by-rtas : set to indicate that the port is in use by the OpenFirmware + RTAS and should not be registered. + +Example: + + uart@80230000 { + compatible = "ns8250"; + reg = <0x80230000 0x100>; + clock-frequency = <3686400>; + interrupts = <10>; + reg-shift = <2>; + }; |