diff options
Diffstat (limited to 'Documentation/devicetree')
152 files changed, 3960 insertions, 179 deletions
diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt new file mode 100644 index 00000000000..ecdb57d69db --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-reset.txt @@ -0,0 +1,11 @@ +Altera SOCFPGA Reset Manager + +Required properties: +- compatible : "altr,rst-mgr" +- reg : Should contain 1 register ranges(address and length) + +Example: + rstmgr@ffd05000 { + compatible = "altr,rst-mgr"; + reg = <0xffd05000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt new file mode 100644 index 00000000000..07c65e3cdcb --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-system.txt @@ -0,0 +1,11 @@ +Altera SOCFPGA System Manager + +Required properties: +- compatible : "altr,sys-mgr" +- reg : Should contain 1 register ranges(address and length) + +Example: + sysmgr@ffd08000 { + compatible = "altr,sys-mgr"; + reg = <0xffd08000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index fc81a7d6b0f..db5858e32d3 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -9,6 +9,10 @@ Required properties (in root node): FPGA type interrupt controllers, see the versatile-fpga-irq binding doc. +In the root node the Integrator/CP must have a /cpcon node pointing +to the CP control registers, and the Integrator/AP must have a +/syscon node pointing to the Integrator/AP system controller. + ARM Versatile Application and Platform Baseboards ------------------------------------------------- diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt b/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt index 70c0dc5f00e..61df564c0d2 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt +++ b/Documentation/devicetree/bindings/arm/armada-370-xp-mpic.txt @@ -6,9 +6,15 @@ Required properties: - interrupt-controller: Identifies the node as an interrupt controller. - #interrupt-cells: The number of cells to define the interrupts. Should be 1. The cell is the IRQ number + - reg: Should contain PMIC registers location and length. First pair for the main interrupt registers, second pair for the per-CPU - interrupt registers + interrupt registers. For this last pair, to be compliant with SMP + support, the "virtual" must be use (For the record, these registers + automatically map to the interrupt controller registers of the + current CPU) + + Example: @@ -18,6 +24,6 @@ Example: #address-cells = <1>; #size-cells = <1>; interrupt-controller; - reg = <0xd0020000 0x1000>, - <0xd0021000 0x1000>; + reg = <0xd0020a00 0x1d0>, + <0xd0021070 0x58>; }; diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt b/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt new file mode 100644 index 00000000000..926b4d6aae7 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-370-xp-pmsu.txt @@ -0,0 +1,20 @@ +Power Management Service Unit(PMSU) +----------------------------------- +Available on Marvell SOCs: Armada 370 and Armada XP + +Required properties: + +- compatible: "marvell,armada-370-xp-pmsu" + +- reg: Should contain PMSU registers location and length. First pair + for the per-CPU SW Reset Control registers, second pair for the + Power Management Service Unit. + +Example: + +armada-370-xp-pmsu@d0022000 { + compatible = "marvell,armada-370-xp-pmsu"; + reg = <0xd0022100 0x430>, + <0xd0020800 0x20>; +}; + diff --git a/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt b/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt index 8b6ea2267c9..64830118b01 100644 --- a/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt +++ b/Documentation/devicetree/bindings/arm/armada-370-xp-timer.txt @@ -5,6 +5,7 @@ Required properties: - compatible: Should be "marvell,armada-370-xp-timer" - interrupts: Should contain the list of Global Timer interrupts - reg: Should contain the base address of the Global Timer registers +- clocks: clock driving the timer hardware Optional properties: - marvell,timer-25Mhz: Tells whether the Global timer supports the 25 diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index ecc81e36871..1196290082d 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -7,8 +7,14 @@ PIT Timer required properties: - interrupts: Should contain interrupt for the PIT which is the IRQ line shared across all System Controller members. +System Timer (ST) required properties: +- compatible: Should be "atmel,at91rm9200-st" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt for the ST which is the IRQ line + shared across all System Controller members. + TC/TCLIB Timer required properties: -- compatible: Should be "atmel,<chip>-pit". +- compatible: Should be "atmel,<chip>-tcb". <chip> can be "at91rm9200" or "at91sam9x5" - reg: Should contain registers location and length - interrupts: Should contain all interrupts for the TC block diff --git a/Documentation/devicetree/bindings/arm/bcm/bcm11351.txt b/Documentation/devicetree/bindings/arm/bcm/bcm11351.txt new file mode 100644 index 00000000000..fb7b5cd2652 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/bcm11351.txt @@ -0,0 +1,9 @@ +Broadcom BCM11351 device tree bindings +------------------------------------------- + +Boards with the bcm281xx SoC family (which includes bcm11130, bcm11140, +bcm11351, bcm28145, bcm28155 SoCs) shall have the following properties: + +Required root node property: + +compatible = "bcm,bcm11351"; diff --git a/Documentation/devicetree/bindings/arm/calxeda.txt b/Documentation/devicetree/bindings/arm/calxeda.txt index 4755caaccba..25fcf96795c 100644 --- a/Documentation/devicetree/bindings/arm/calxeda.txt +++ b/Documentation/devicetree/bindings/arm/calxeda.txt @@ -1,8 +1,15 @@ -Calxeda Highbank Platforms Device Tree Bindings +Calxeda Platforms Device Tree Bindings ----------------------------------------------- -Boards with Calxeda Cortex-A9 based Highbank SOC shall have the following -properties. +Boards with Calxeda Cortex-A9 based ECX-1000 (Highbank) SOC shall have the +following properties. Required root node properties: - compatible = "calxeda,highbank"; + + +Boards with Calxeda Cortex-A15 based ECX-2000 SOC shall have the following +properties. + +Required root node properties: + - compatible = "calxeda,ecx-2000"; diff --git a/Documentation/devicetree/bindings/arm/coherency-fabric.txt b/Documentation/devicetree/bindings/arm/coherency-fabric.txt new file mode 100644 index 00000000000..17d8cd10755 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/coherency-fabric.txt @@ -0,0 +1,21 @@ +Coherency fabric +---------------- +Available on Marvell SOCs: Armada 370 and Armada XP + +Required properties: + +- compatible: "marvell,coherency-fabric" + +- reg: Should contain coherency fabric registers location and + length. First pair for the coherency fabric registers, second pair + for the per-CPU fabric registers registers. + +Example: + +coherency-fabric@d0020200 { + compatible = "marvell,coherency-fabric"; + reg = <0xd0020200 0xb0>, + <0xd0021810 0x1c>; + +}; + diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt new file mode 100644 index 00000000000..f32494dbfe1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -0,0 +1,77 @@ +* ARM CPUs binding description + +The device tree allows to describe the layout of CPUs in a system through +the "cpus" node, which in turn contains a number of subnodes (ie "cpu") +defining properties for every cpu. + +Bindings for CPU nodes follow the ePAPR standard, available from: + +http://devicetree.org + +For the ARM architecture every CPU node must contain the following properties: + +- device_type: must be "cpu" +- reg: property matching the CPU MPIDR[23:0] register bits + reg[31:24] bits must be set to 0 +- compatible: should be one of: + "arm,arm1020" + "arm,arm1020e" + "arm,arm1022" + "arm,arm1026" + "arm,arm720" + "arm,arm740" + "arm,arm7tdmi" + "arm,arm920" + "arm,arm922" + "arm,arm925" + "arm,arm926" + "arm,arm940" + "arm,arm946" + "arm,arm9tdmi" + "arm,cortex-a5" + "arm,cortex-a7" + "arm,cortex-a8" + "arm,cortex-a9" + "arm,cortex-a15" + "arm,arm1136" + "arm,arm1156" + "arm,arm1176" + "arm,arm11mpcore" + "faraday,fa526" + "intel,sa110" + "intel,sa1100" + "marvell,feroceon" + "marvell,mohawk" + "marvell,xsc3" + "marvell,xscale" + +Example: + + cpus { + #size-cells = <0>; + #address-cells = <1>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x1>; + }; + + CPU2: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x100>; + }; + + CPU3: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x101>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/davinci.txt b/Documentation/devicetree/bindings/arm/davinci.txt new file mode 100644 index 00000000000..cfaeda4274e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/davinci.txt @@ -0,0 +1,17 @@ +Texas Instruments DaVinci Platforms Device Tree Bindings +-------------------------------------------------------- + +DA850/OMAP-L138/AM18x Evaluation Module (EVM) board +Required root node properties: + - compatible = "ti,da850-evm", "ti,da850"; + +EnBW AM1808 based CMC board +Required root node properties: + - compatible = "enbw,cmc", "ti,da850; + +Generic DaVinci Boards +---------------------- + +DA850/OMAP-L138/AM18x generic board +Required root node properties: + - compatible = "ti,da850"; diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt index e37241f1fdd..3545ea704b5 100644 --- a/Documentation/devicetree/bindings/arm/davinci/nand.txt +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt @@ -23,29 +23,24 @@ Recommended properties : - ti,davinci-nand-buswidth: buswidth 8 or 16 - ti,davinci-nand-use-bbt: use flash based bad block table support. -Example (enbw_cmc board): -aemif@60000000 { - compatible = "ti,davinci-aemif"; - #address-cells = <2>; - #size-cells = <1>; - reg = <0x68000000 0x80000>; - ranges = <2 0 0x60000000 0x02000000 - 3 0 0x62000000 0x02000000 - 4 0 0x64000000 0x02000000 - 5 0 0x66000000 0x02000000 - 6 0 0x68000000 0x02000000>; - nand@3,0 { - compatible = "ti,davinci-nand"; - reg = <3 0x0 0x807ff - 6 0x0 0x8000>; - #address-cells = <1>; - #size-cells = <1>; - ti,davinci-chipselect = <1>; - ti,davinci-mask-ale = <0>; - ti,davinci-mask-cle = <0>; - ti,davinci-mask-chipsel = <0>; - ti,davinci-ecc-mode = "hw"; - ti,davinci-ecc-bits = <4>; - ti,davinci-nand-use-bbt; +nand device bindings may contain additional sub-nodes describing +partitions of the address space. See partition.txt for more detail. + +Example(da850 EVM ): +nand_cs3@62000000 { + compatible = "ti,davinci-nand"; + reg = <0x62000000 0x807ff + 0x68000000 0x8000>; + ti,davinci-chipselect = <1>; + ti,davinci-mask-ale = <0>; + ti,davinci-mask-cle = <0>; + ti,davinci-mask-chipsel = <0>; + ti,davinci-ecc-mode = "hw"; + ti,davinci-ecc-bits = <4>; + ti,davinci-nand-use-bbt; + + partition@180000 { + label = "ubifs"; + reg = <0x180000 0x7e80000>; }; }; diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt index 6528e215c5f..5216b419016 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -4,14 +4,13 @@ Exynos processors include support for multiple power domains which are used to gate power to one or more peripherals on the processor. Required Properties: -- compatiable: should be one of the following. +- compatible: should be one of the following. * samsung,exynos4210-pd - for exynos4210 type power domain. - reg: physical base address of the controller and length of memory mapped region. -Optional Properties: -- samsung,exynos4210-pd-off: Specifies that the power domain is in turned-off - state during boot and remains to be turned-off until explicitly turned-on. +Node of a device using power domains must have a samsung,power-domain property +defined with a phandle to respective power domain. Example: @@ -19,3 +18,11 @@ Example: compatible = "samsung,exynos4210-pd"; reg = <0x10023C00 0x10>; }; + +Example of the node using power domain: + + node { + /* ... */ + samsung,power-domain = <&lcd0>; + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index ac9e7516756..f79818711e8 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -41,6 +41,10 @@ i.MX6 Quad SABRE Smart Device Board Required root node properties: - compatible = "fsl,imx6q-sabresd", "fsl,imx6q"; +i.MX6 Quad SABRE Automotive Board +Required root node properties: + - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q"; + Generic i.MX boards ------------------- diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt index 7ca52161e7a..cbef09b5c8a 100644 --- a/Documentation/devicetree/bindings/arm/l2cc.txt +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -10,6 +10,12 @@ Required properties: "arm,pl310-cache" "arm,l220-cache" "arm,l210-cache" + "marvell,aurora-system-cache": Marvell Controller designed to be + compatible with the ARM one, with system cache mode (meaning + maintenance operations on L1 are broadcasted to the L2 and L2 + performs the same operation). + "marvell,"aurora-outer-cache: Marvell Controller designed to be + compatible with the ARM one with outer cache mode. - cache-unified : Specifies the cache is a unified cache. - cache-level : Should be set to 2 for a level 2 cache. - reg : Physical base address and size of cache controller's memory mapped @@ -29,6 +35,9 @@ Optional properties: filter. Addresses in the filter window are directed to the M1 port. Other addresses will go to the M0 port. - interrupts : 1 combined interrupt. +- cache-id-part: cache id part number to be used if it is not present + on hardware +- wt-override: If present then L2 is forced to Write through mode Example: @@ -37,7 +46,7 @@ L2: cache-controller { reg = <0xfff12000 0x1000>; arm,data-latency = <1 1 1>; arm,tag-latency = <2 2 2>; - arm,filter-latency = <0x80000000 0x8000000>; + arm,filter-ranges = <0x80000000 0x8000000>; cache-unified; cache-level = <2>; interrupts = <45>; diff --git a/Documentation/devicetree/bindings/arm/omap/counter.txt b/Documentation/devicetree/bindings/arm/omap/counter.txt new file mode 100644 index 00000000000..5bd8aa09131 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/counter.txt @@ -0,0 +1,15 @@ +OMAP Counter-32K bindings + +Required properties: +- compatible: Must be "ti,omap-counter32k" for OMAP controllers +- reg: Contains timer register address range (base address and length) +- ti,hwmods: Name of the hwmod associated to the counter, which is typically + "counter_32k" + +Example: + +counter32k: counter@4a304000 { + compatible = "ti,omap-counter32k"; + reg = <0x4a304000 0x20>; + ti,hwmods = "counter_32k"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/timer.txt b/Documentation/devicetree/bindings/arm/omap/timer.txt new file mode 100644 index 00000000000..8732d4d41f8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/timer.txt @@ -0,0 +1,31 @@ +OMAP Timer bindings + +Required properties: +- compatible: Must be "ti,omap2-timer" for OMAP2+ controllers. +- reg: Contains timer register address range (base address and + length). +- interrupts: Contains the interrupt information for the timer. The + format is being dependent on which interrupt controller + the OMAP device uses. +- ti,hwmods: Name of the hwmod associated to the timer, "timer<X>", + where <X> is the instance number of the timer from the + HW spec. + +Optional properties: +- ti,timer-alwon: Indicates the timer is in an alway-on power domain. +- ti,timer-dsp: Indicates the timer can interrupt the on-chip DSP in + addition to the ARM CPU. +- ti,timer-pwm: Indicates the timer can generate a PWM output. +- ti,timer-secure: Indicates the timer is reserved on a secure OMAP device + and therefore cannot be used by the kernel. + +Example: + +timer12: timer@48304000 { + compatible = "ti,omap2-timer"; + reg = <0x48304000 0x400>; + interrupts = <95>; + ti,hwmods = "timer12" + ti,timer-alwon; + ti,timer-secure; +}; diff --git a/Documentation/devicetree/bindings/arm/spear/shirq.txt b/Documentation/devicetree/bindings/arm/spear/shirq.txt new file mode 100644 index 00000000000..13fbb8866bd --- /dev/null +++ b/Documentation/devicetree/bindings/arm/spear/shirq.txt @@ -0,0 +1,48 @@ +* SPEAr Shared IRQ layer (shirq) + +SPEAr3xx architecture includes shared/multiplexed irqs for certain set +of devices. The multiplexor provides a single interrupt to parent +interrupt controller (VIC) on behalf of a group of devices. + +There can be multiple groups available on SPEAr3xx variants but not +exceeding 4. The number of devices in a group can differ, further they +may share same set of status/mask registers spanning across different +bit masks. Also in some cases the group may not have enable or other +registers. This makes software little complex. + +A single node in the device tree is used to describe the shared +interrupt multiplexor (one node for all groups). A group in the +interrupt controller shares config/control registers with other groups. +For example, a 32-bit interrupt enable/disable config register can +accommodate upto 4 interrupt groups. + +Required properties: + - compatible: should be, either of + - "st,spear300-shirq" + - "st,spear310-shirq" + - "st,spear320-shirq" + - interrupt-controller: Identifies the node as an interrupt controller. + - #interrupt-cells: should be <1> which basically contains the offset + (starting from 0) of interrupts for all the groups. + - reg: Base address and size of shirq registers. + - interrupts: The list of interrupts generated by the groups which are + then connected to a parent interrupt controller. Each group is + associated with one of the interrupts, hence number of interrupts (to + parent) is equal to number of groups. The format of the interrupt + specifier depends in the interrupt parent controller. + + Optional properties: + - interrupt-parent: pHandle of the parent interrupt controller, if not + inherited from the parent node. + +Example: + +The following is an example from the SPEAr320 SoC dtsi file. + +shirq: interrupt-controller@0xb3000000 { + compatible = "st,spear320-shirq"; + reg = <0xb3000000 0x1000>; + interrupts = <28 29 30 1>; + #interrupt-cells = <1>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt new file mode 100644 index 00000000000..9cf3f25544c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vexpress-sysreg.txt @@ -0,0 +1,50 @@ +ARM Versatile Express system registers +-------------------------------------- + +This is a system control registers block, providing multiple low level +platform functions like board detection and identification, software +interrupt generation, MMC and NOR Flash control etc. + +Required node properties: +- compatible value : = "arm,vexpress,sysreg"; +- reg : physical base address and the size of the registers window +- gpio-controller : specifies that the node is a GPIO controller +- #gpio-cells : size of the GPIO specifier, should be 2: + - first cell is the pseudo-GPIO line number: + 0 - MMC CARDIN + 1 - MMC WPROT + 2 - NOR FLASH WPn + - second cell can take standard GPIO flags (currently ignored). + +Example: + v2m_sysreg: sysreg@10000000 { + compatible = "arm,vexpress-sysreg"; + reg = <0x10000000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + }; + +This block also can also act a bridge to the platform's configuration +bus via "system control" interface, addressing devices with site number, +position in the board stack, config controller, function and device +numbers - see motherboard's TRM for more details. + +The node describing a config device must refer to the sysreg node via +"arm,vexpress,config-bridge" phandle (can be also defined in the node's +parent) and relies on the board topology properties - see main vexpress +node documentation for more details. It must must also define the +following property: +- arm,vexpress-sysreg,func : must contain two cells: + - first cell defines function number (eg. 1 for clock generator, + 2 for voltage regulators etc.) + - device number (eg. osc 0, osc 1 etc.) + +Example: + mcc { + arm,vexpress,config-bridge = <&v2m_sysreg>; + + osc@0 { + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 0>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/vexpress.txt b/Documentation/devicetree/bindings/arm/vexpress.txt index ec8b50cbb2e..ae49161e478 100644 --- a/Documentation/devicetree/bindings/arm/vexpress.txt +++ b/Documentation/devicetree/bindings/arm/vexpress.txt @@ -11,6 +11,10 @@ the motherboard file using a /include/ directive. As the motherboard can be initialized in one of two different configurations ("memory maps"), care must be taken to include the correct one. + +Root node +--------- + Required properties in the root node: - compatible value: compatible = "arm,vexpress,<model>", "arm,vexpress"; @@ -45,6 +49,10 @@ Optional properties in the root node: - Coretile Express A9x4 (V2P-CA9) HBI-0225: arm,hbi = <0x225>; + +CPU nodes +--------- + Top-level standard "cpus" node is required. It must contain a node with device_type = "cpu" property for every available core, eg.: @@ -59,6 +67,52 @@ with device_type = "cpu" property for every available core, eg.: }; }; + +Configuration infrastructure +---------------------------- + +The platform has an elaborated configuration system, consisting of +microcontrollers residing on the mother- and daughterboards known +as Motherboard/Daughterboard Configuration Controller (MCC and DCC). +The controllers are responsible for the platform initialization +(reset generation, flash programming, FPGA bitfiles loading etc.) +but also control clock generators, voltage regulators, gather +environmental data like temperature, power consumption etc. Even +the video output switch (FPGA) is controlled that way. + +Nodes describing devices controlled by this infrastructure should +point at the bridge device node: +- bridge phandle: + arm,vexpress,config-bridge = <phandle>; +This property can be also defined in a parent node (eg. for a DCC) +and is effective for all children. + + +Platform topology +----------------- + +As Versatile Express can be configured in number of physically +different setups, the device tree should describe platform topology. +Root node and main motherboard node must define the following +property, describing physical location of the children nodes: +- site number: + arm,vexpress,site = <number>; + where 0 means motherboard, 1 or 2 are daugtherboard sites, + 0xf means "master" site (site containing main CPU tile) +- when daughterboards are stacked on one site, their position + in the stack be be described with: + arm,vexpress,position = <number>; +- when describing tiles consisting more than one DCC, its number + can be described with: + arm,vexpress,dcc = <number>; + +Any of the numbers above defaults to zero if not defined in +the node or any of its parent. + + +Motherboard +----------- + The motherboard description file provides a single "motherboard" node using 2 address cells corresponding to the Static Memory Bus used between the motherboard and the tile. The first cell defines the Chip @@ -87,22 +141,30 @@ can be used to obtain required phandle in the tile's "aliases" node: - SP804 timers: v2m_timer01 and v2m_timer23 -Current Linux implementation requires a "arm,v2m_timer" alias -pointing at one of the motherboard's SP804 timers, if it is to be -used as the system timer. This alias should be defined in the -motherboard files. +The tile description should define a "smb" node, describing the +Static Memory Bus between the tile and motherboard. It must define +the following properties: +- "simple-bus" compatible value (to ensure creation of the children) + compatible = "simple-bus"; +- mapping of the SMB CS/offset addresses into main address space: + #address-cells = <2>; + #size-cells = <1>; + ranges = <...>; +- interrupts mapping: + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 63>; + interrupt-map = <...>; -The tile description must define "ranges", "interrupt-map-mask" and -"interrupt-map" properties to translate the motherboard's address -and interrupt space into one used by the tile's processor. -Abbreviated example: +Example of a VE tile description (simplified) +--------------------------------------------- /dts-v1/; / { model = "V2P-CA5s"; arm,hbi = <0x225>; + arm,vexpress,site = <0xf>; compatible = "arm,vexpress-v2p-ca5s", "arm,vexpress"; interrupt-parent = <&gic>; #address-cells = <1>; @@ -134,13 +196,29 @@ Abbreviated example: <0x2c000100 0x100>; }; - motherboard { + dcc { + compatible = "simple-bus"; + arm,vexpress,config-bridge = <&v2m_sysreg>; + + osc@0 { + compatible = "arm,vexpress-osc"; + }; + }; + + smb { + compatible = "simple-bus"; + + #address-cells = <2>; + #size-cells = <1>; /* CS0 is visible at 0x08000000 */ ranges = <0 0 0x08000000 0x04000000>; + + #interrupt-cells = <1>; interrupt-map-mask = <0 0 63>; /* Active high IRQ 0 is connected to GIC's SPI0 */ interrupt-map = <0 0 0 &gic 0 0 4>; + + /include/ "vexpress-v2m-rs1.dtsi" }; }; -/include/ "vexpress-v2m-rs1.dtsi" diff --git a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt new file mode 100644 index 00000000000..37824fac688 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt @@ -0,0 +1,14 @@ +* Samsung SATA PHY Controller + +SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. +Each SATA PHY controller should have its own node. + +Required properties: +- compatible : compatible list, contains "samsung,exynos5-sata-phy" +- reg : <registers mapping> + +Example: + sata@ffe07000 { + compatible = "samsung,exynos5-sata-phy"; + reg = <0xffe07000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/ata/exynos-sata.txt b/Documentation/devicetree/bindings/ata/exynos-sata.txt new file mode 100644 index 00000000000..0849f1025e3 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/exynos-sata.txt @@ -0,0 +1,17 @@ +* Samsung AHCI SATA Controller + +SATA nodes are defined to describe on-chip Serial ATA controllers. +Each SATA controller should have its own node. + +Required properties: +- compatible : compatible list, contains "samsung,exynos5-sata" +- interrupts : <interrupt mapping for SATA IRQ> +- reg : <registers mapping> +- samsung,sata-freq : <frequency in MHz> + +Example: + sata@ffe08000 { + compatible = "samsung,exynos5-sata"; + reg = <0xffe08000 0x1000>; + interrupts = <115>; + }; diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt index d2fe064a828..63dd8051521 100644 --- a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt @@ -2,9 +2,27 @@ properties: - compatible : Should be "ti,omap-ocp2scp" +- reg : Address and length of the register set for the device - #address-cells, #size-cells : Must be present if the device has sub-nodes - ranges : the child address space are mapped 1:1 onto the parent address space - ti,hwmods : must be "ocp2scp_usb_phy" Sub-nodes: All the devices connected to ocp2scp are described using sub-node to ocp2scp + +ocp2scp@4a0ad000 { + compatible = "ti,omap-ocp2scp"; + reg = <0x4a0ad000 0x1f>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "ocp2scp_usb_phy"; + + subnode1 { + ... + }; + + subnode2 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/clock/imx23-clock.txt b/Documentation/devicetree/bindings/clock/imx23-clock.txt index a0b867ef8d9..baadbb11fe9 100644 --- a/Documentation/devicetree/bindings/clock/imx23-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx23-clock.txt @@ -52,7 +52,7 @@ clocks and IDs. lcdif 38 etm 39 usb 40 - usb_pwr 41 + usb_phy 41 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx25-clock.txt b/Documentation/devicetree/bindings/clock/imx25-clock.txt new file mode 100644 index 00000000000..c2a3525ecb4 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx25-clock.txt @@ -0,0 +1,162 @@ +* Clock bindings for Freescale i.MX25 + +Required properties: +- compatible: Should be "fsl,imx25-ccm" +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX25 +clocks and IDs. + + Clock ID + --------------------------- + dummy 0 + osc 1 + mpll 2 + upll 3 + mpll_cpu_3_4 4 + cpu_sel 5 + cpu 6 + ahb 7 + usb_div 8 + ipg 9 + per0_sel 10 + per1_sel 11 + per2_sel 12 + per3_sel 13 + per4_sel 14 + per5_sel 15 + per6_sel 16 + per7_sel 17 + per8_sel 18 + per9_sel 19 + per10_sel 20 + per11_sel 21 + per12_sel 22 + per13_sel 23 + per14_sel 24 + per15_sel 25 + per0 26 + per1 27 + per2 28 + per3 29 + per4 30 + per5 31 + per6 32 + per7 33 + per8 34 + per9 35 + per10 36 + per11 37 + per12 38 + per13 39 + per14 40 + per15 41 + csi_ipg_per 42 + epit_ipg_per 43 + esai_ipg_per 44 + esdhc1_ipg_per 45 + esdhc2_ipg_per 46 + gpt_ipg_per 47 + i2c_ipg_per 48 + lcdc_ipg_per 49 + nfc_ipg_per 50 + owire_ipg_per 51 + pwm_ipg_per 52 + sim1_ipg_per 53 + sim2_ipg_per 54 + ssi1_ipg_per 55 + ssi2_ipg_per 56 + uart_ipg_per 57 + ata_ahb 58 + reserved 59 + csi_ahb 60 + emi_ahb 61 + esai_ahb 62 + esdhc1_ahb 63 + esdhc2_ahb 64 + fec_ahb 65 + lcdc_ahb 66 + rtic_ahb 67 + sdma_ahb 68 + slcdc_ahb 69 + usbotg_ahb 70 + reserved 71 + reserved 72 + reserved 73 + reserved 74 + can1_ipg 75 + can2_ipg 76 + csi_ipg 77 + cspi1_ipg 78 + cspi2_ipg 79 + cspi3_ipg 80 + dryice_ipg 81 + ect_ipg 82 + epit1_ipg 83 + epit2_ipg 84 + reserved 85 + esdhc1_ipg 86 + esdhc2_ipg 87 + fec_ipg 88 + reserved 89 + reserved 90 + reserved 91 + gpt1_ipg 92 + gpt2_ipg 93 + gpt3_ipg 94 + gpt4_ipg 95 + reserved 96 + reserved 97 + reserved 98 + iim_ipg 99 + reserved 100 + reserved 101 + kpp_ipg 102 + lcdc_ipg 103 + reserved 104 + pwm1_ipg 105 + pwm2_ipg 106 + pwm3_ipg 107 + pwm4_ipg 108 + rngb_ipg 109 + reserved 110 + scc_ipg 111 + sdma_ipg 112 + sim1_ipg 113 + sim2_ipg 114 + slcdc_ipg 115 + spba_ipg 116 + ssi1_ipg 117 + ssi2_ipg 118 + tsc_ipg 119 + uart1_ipg 120 + uart2_ipg 121 + uart3_ipg 122 + uart4_ipg 123 + uart5_ipg 124 + reserved 125 + wdt_ipg 126 + +Examples: + +clks: ccm@53f80000 { + compatible = "fsl,imx25-ccm"; + reg = <0x53f80000 0x4000>; + interrupts = <31>; + clock-output-names = ... + "uart_ipg", + "uart_serial", + ...; +}; + +uart1: serial@43f90000 { + compatible = "fsl,imx25-uart", "fsl,imx21-uart"; + reg = <0x43f90000 0x4000>; + interrupts = <45>; + clocks = <&clks 79>, <&clks 50>; + clock-names = "ipg", "per"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx28-clock.txt b/Documentation/devicetree/bindings/clock/imx28-clock.txt index aa2af2866fe..52a49a4a50b 100644 --- a/Documentation/devicetree/bindings/clock/imx28-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx28-clock.txt @@ -73,8 +73,8 @@ clocks and IDs. can1 59 usb0 60 usb1 61 - usb0_pwr 62 - usb1_pwr 63 + usb0_phy 62 + usb1_phy 63 enet_out 64 Examples: diff --git a/Documentation/devicetree/bindings/clock/imx5-clock.txt b/Documentation/devicetree/bindings/clock/imx5-clock.txt new file mode 100644 index 00000000000..04ad47876be --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx5-clock.txt @@ -0,0 +1,191 @@ +* Clock bindings for Freescale i.MX5 + +Required properties: +- compatible: Should be "fsl,<soc>-ccm" , where <soc> can be imx51 or imx53 +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX5 +clocks and IDs. + + Clock ID + --------------------------- + dummy 0 + ckil 1 + osc 2 + ckih1 3 + ckih2 4 + ahb 5 + ipg 6 + axi_a 7 + axi_b 8 + uart_pred 9 + uart_root 10 + esdhc_a_pred 11 + esdhc_b_pred 12 + esdhc_c_s 13 + esdhc_d_s 14 + emi_sel 15 + emi_slow_podf 16 + nfc_podf 17 + ecspi_pred 18 + ecspi_podf 19 + usboh3_pred 20 + usboh3_podf 21 + usb_phy_pred 22 + usb_phy_podf 23 + cpu_podf 24 + di_pred 25 + tve_di 26 + tve_s 27 + uart1_ipg_gate 28 + uart1_per_gate 29 + uart2_ipg_gate 30 + uart2_per_gate 31 + uart3_ipg_gate 32 + uart3_per_gate 33 + i2c1_gate 34 + i2c2_gate 35 + gpt_ipg_gate 36 + pwm1_ipg_gate 37 + pwm1_hf_gate 38 + pwm2_ipg_gate 39 + pwm2_hf_gate 40 + gpt_hf_gate 41 + fec_gate 42 + usboh3_per_gate 43 + esdhc1_ipg_gate 44 + esdhc2_ipg_gate 45 + esdhc3_ipg_gate 46 + esdhc4_ipg_gate 47 + ssi1_ipg_gate 48 + ssi2_ipg_gate 49 + ssi3_ipg_gate 50 + ecspi1_ipg_gate 51 + ecspi1_per_gate 52 + ecspi2_ipg_gate 53 + ecspi2_per_gate 54 + cspi_ipg_gate 55 + sdma_gate 56 + emi_slow_gate 57 + ipu_s 58 + ipu_gate 59 + nfc_gate 60 + ipu_di1_gate 61 + vpu_s 62 + vpu_gate 63 + vpu_reference_gate 64 + uart4_ipg_gate 65 + uart4_per_gate 66 + uart5_ipg_gate 67 + uart5_per_gate 68 + tve_gate 69 + tve_pred 70 + esdhc1_per_gate 71 + esdhc2_per_gate 72 + esdhc3_per_gate 73 + esdhc4_per_gate 74 + usb_phy_gate 75 + hsi2c_gate 76 + mipi_hsc1_gate 77 + mipi_hsc2_gate 78 + mipi_esc_gate 79 + mipi_hsp_gate 80 + ldb_di1_div_3_5 81 + ldb_di1_div 82 + ldb_di0_div_3_5 83 + ldb_di0_div 84 + ldb_di1_gate 85 + can2_serial_gate 86 + can2_ipg_gate 87 + i2c3_gate 88 + lp_apm 89 + periph_apm 90 + main_bus 91 + ahb_max 92 + aips_tz1 93 + aips_tz2 94 + tmax1 95 + tmax2 96 + tmax3 97 + spba 98 + uart_sel 99 + esdhc_a_sel 100 + esdhc_b_sel 101 + esdhc_a_podf 102 + esdhc_b_podf 103 + ecspi_sel 104 + usboh3_sel 105 + usb_phy_sel 106 + iim_gate 107 + usboh3_gate 108 + emi_fast_gate 109 + ipu_di0_gate 110 + gpc_dvfs 111 + pll1_sw 112 + pll2_sw 113 + pll3_sw 114 + ipu_di0_sel 115 + ipu_di1_sel 116 + tve_ext_sel 117 + mx51_mipi 118 + pll4_sw 119 + ldb_di1_sel 120 + di_pll4_podf 121 + ldb_di0_sel 122 + ldb_di0_gate 123 + usb_phy1_gate 124 + usb_phy2_gate 125 + per_lp_apm 126 + per_pred1 127 + per_pred2 128 + per_podf 129 + per_root 130 + ssi_apm 131 + ssi1_root_sel 132 + ssi2_root_sel 133 + ssi3_root_sel 134 + ssi_ext1_sel 135 + ssi_ext2_sel 136 + ssi_ext1_com_sel 137 + ssi_ext2_com_sel 138 + ssi1_root_pred 139 + ssi1_root_podf 140 + ssi2_root_pred 141 + ssi2_root_podf 142 + ssi_ext1_pred 143 + ssi_ext1_podf 144 + ssi_ext2_pred 145 + ssi_ext2_podf 146 + ssi1_root_gate 147 + ssi2_root_gate 148 + ssi3_root_gate 149 + ssi_ext1_gate 150 + ssi_ext2_gate 151 + epit1_ipg_gate 152 + epit1_hf_gate 153 + epit2_ipg_gate 154 + epit2_hf_gate 155 + can_sel 156 + can1_serial_gate 157 + can1_ipg_gate 158 + +Examples (for mx53): + +clks: ccm@53fd4000{ + compatible = "fsl,imx53-ccm"; + reg = <0x53fd4000 0x4000>; + interrupts = <0 71 0x04 0 72 0x04>; + #clock-cells = <1>; +}; + +can1: can@53fc8000 { + compatible = "fsl,imx53-flexcan", "fsl,p1010-flexcan"; + reg = <0x53fc8000 0x4000>; + interrupts = <82>; + clocks = <&clks 158>, <&clks 157>; + clock-names = "ipg", "per"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index 492bd991d52..d77b4e68dc4 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -187,9 +187,9 @@ clocks and IDs. pll3_usb_otg 172 pll4_audio 173 pll5_video 174 - pll6_mlb 175 + pll8_mlb 175 pll7_usb_host 176 - pll8_enet 177 + pll6_enet 177 ssi1_ipg 178 ssi2_ipg 179 ssi3_ipg 180 @@ -198,6 +198,11 @@ clocks and IDs. usbphy2 183 ldb_di0_div_3_5 184 ldb_di1_div_3_5 185 + sata_ref 186 + sata_ref_100m 187 + pcie_ref 188 + pcie_ref_125m 189 + enet_ref 190 Examples: diff --git a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt new file mode 100644 index 00000000000..1e662948661 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt @@ -0,0 +1,47 @@ +* Core Clock bindings for Marvell MVEBU SoCs + +Marvell MVEBU SoCs usually allow to determine core clock frequencies by +reading the Sample-At-Reset (SAR) register. The core clock consumer should +specify the desired clock by having the clock ID in its "clocks" phandle cell. + +The following is a list of provided IDs and clock names on Armada 370/XP: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = nbclk (L2 Cache clock) + 3 = hclk (DRAM control clock) + 4 = dramclk (DDR clock) + +The following is a list of provided IDs and clock names on Kirkwood and Dove: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU0 clock) + 2 = l2clk (L2 Cache clock derived from CPU0 clock) + 3 = ddrclk (DDR controller clock derived from CPU0 clock) + +Required properties: +- compatible : shall be one of the following: + "marvell,armada-370-core-clock" - For Armada 370 SoC core clocks + "marvell,armada-xp-core-clock" - For Armada XP SoC core clocks + "marvell,dove-core-clock" - for Dove SoC core clocks + "marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180) + "marvell,mv88f6180-core-clock" - for Kirkwood MV88f6180 SoC +- reg : shall be the register address of the Sample-At-Reset (SAR) register +- #clock-cells : from common clock binding; shall be set to 1 + +Optional properties: +- clock-output-names : from common clock binding; allows overwrite default clock + output names ("tclk", "cpuclk", "l2clk", "ddrclk") + +Example: + +core_clk: core-clocks@d0214 { + compatible = "marvell,dove-core-clock"; + reg = <0xd0214 0x4>; + #clock-cells = <1>; +}; + +spi0: spi@10600 { + compatible = "marvell,orion-spi"; + /* ... */ + /* get tclk from core clock provider */ + clocks = <&core_clk 0>; +}; diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt new file mode 100644 index 00000000000..feb83013071 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt @@ -0,0 +1,21 @@ +Device Tree Clock bindings for cpu clock of Marvell EBU platforms + +Required properties: +- compatible : shall be one of the following: + "marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP +- reg : Address and length of the clock complex register set +- #clock-cells : should be set to 1. +- clocks : shall be the input parent clock phandle for the clock. + +cpuclk: clock-complex@d0018700 { + #clock-cells = <1>; + compatible = "marvell,armada-xp-cpu-clock"; + reg = <0xd0018700 0xA0>; + clocks = <&coreclk 1>; +} + +cpu@0 { + compatible = "marvell,sheeva-v7"; + reg = <0>; + clocks = <&cpuclk 0>; +}; diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt new file mode 100644 index 00000000000..7337005ef5e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt @@ -0,0 +1,119 @@ +* Gated Clock bindings for Marvell Orion SoCs + +Marvell Dove and Kirkwood allow some peripheral clocks to be gated to save +some power. The clock consumer should specify the desired clock by having +the clock ID in its "clocks" phandle cell. The clock ID is directly mapped to +the corresponding clock gating control bit in HW to ease manual clock lookup +in datasheet. + +The following is a list of provided IDs for Armada 370: +ID Clock Peripheral +----------------------------------- +0 Audio AC97 Cntrl +1 pex0_en PCIe 0 Clock out +2 pex1_en PCIe 1 Clock out +3 ge1 Gigabit Ethernet 1 +4 ge0 Gigabit Ethernet 0 +5 pex0 PCIe Cntrl 0 +9 pex1 PCIe Cntrl 1 +15 sata0 SATA Host 0 +17 sdio SDHCI Host +25 tdm Time Division Mplx +28 ddr DDR Cntrl +30 sata1 SATA Host 0 + +The following is a list of provided IDs for Armada XP: +ID Clock Peripheral +----------------------------------- +0 audio Audio Cntrl +1 ge3 Gigabit Ethernet 3 +2 ge2 Gigabit Ethernet 2 +3 ge1 Gigabit Ethernet 1 +4 ge0 Gigabit Ethernet 0 +5 pex0 PCIe Cntrl 0 +6 pex1 PCIe Cntrl 1 +7 pex2 PCIe Cntrl 2 +8 pex3 PCIe Cntrl 3 +13 bp +14 sata0lnk +15 sata0 SATA Host 0 +16 lcd LCD Cntrl +17 sdio SDHCI Host +18 usb0 USB Host 0 +19 usb1 USB Host 1 +20 usb2 USB Host 2 +22 xor0 XOR DMA 0 +23 crypto CESA engine +25 tdm Time Division Mplx +28 xor1 XOR DMA 1 +29 sata1lnk +30 sata1 SATA Host 0 + +The following is a list of provided IDs for Dove: +ID Clock Peripheral +----------------------------------- +0 usb0 USB Host 0 +1 usb1 USB Host 1 +2 ge Gigabit Ethernet +3 sata SATA Host +4 pex0 PCIe Cntrl 0 +5 pex1 PCIe Cntrl 1 +8 sdio0 SDHCI Host 0 +9 sdio1 SDHCI Host 1 +10 nand NAND Cntrl +11 camera Camera Cntrl +12 i2s0 I2S Cntrl 0 +13 i2s1 I2S Cntrl 1 +15 crypto CESA engine +21 ac97 AC97 Cntrl +22 pdma Peripheral DMA +23 xor0 XOR DMA 0 +24 xor1 XOR DMA 1 +30 gephy Gigabit Ethernel PHY +Note: gephy(30) is implemented as a parent clock of ge(2) + +The following is a list of provided IDs for Kirkwood: +ID Clock Peripheral +----------------------------------- +0 ge0 Gigabit Ethernet 0 +2 pex0 PCIe Cntrl 0 +3 usb0 USB Host 0 +4 sdio SDIO Cntrl +5 tsu Transp. Stream Unit +6 dunit SDRAM Cntrl +7 runit Runit +8 xor0 XOR DMA 0 +9 audio I2S Cntrl 0 +14 sata0 SATA Host 0 +15 sata1 SATA Host 1 +16 xor1 XOR DMA 1 +17 crypto CESA engine +18 pex1 PCIe Cntrl 1 +19 ge1 Gigabit Ethernet 0 +20 tdm Time Division Mplx + +Required properties: +- compatible : shall be one of the following: + "marvell,dove-gating-clock" - for Dove SoC clock gating + "marvell,kirkwood-gating-clock" - for Kirkwood SoC clock gating +- reg : shall be the register address of the Clock Gating Control register +- #clock-cells : from common clock binding; shall be set to 1 + +Optional properties: +- clocks : default parent clock phandle (e.g. tclk) + +Example: + +gate_clk: clock-gating-control@d0038 { + compatible = "marvell,dove-gating-clock"; + reg = <0xd0038 0x4>; + /* default parent clock is tclk */ + clocks = <&core_clk 0>; + #clock-cells = <1>; +}; + +sdio0: sdio@92000 { + compatible = "marvell,dove-sdhci"; + /* get clk gate bit 8 (sdio0) */ + clocks = <&gate_clk 8>; +}; diff --git a/Documentation/devicetree/bindings/clock/zynq-7000.txt b/Documentation/devicetree/bindings/clock/zynq-7000.txt new file mode 100644 index 00000000000..23ae1db1bc1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/zynq-7000.txt @@ -0,0 +1,55 @@ +Device Tree Clock bindings for the Zynq 7000 EPP + +The Zynq EPP has several different clk providers, each with there own bindings. +The purpose of this document is to document their usage. + +See clock_bindings.txt for more information on the generic clock bindings. +See Chapter 25 of Zynq TRM for more information about Zynq clocks. + +== PLLs == + +Used to describe the ARM_PLL, DDR_PLL, and IO_PLL. + +Required properties: +- #clock-cells : shall be 0 (only one clock is output from this node) +- compatible : "xlnx,zynq-pll" +- reg : pair of u32 values, which are the address offsets within the SLCR + of the relevant PLL_CTRL register and PLL_CFG register respectively +- clocks : phandle for parent clock. should be the phandle for ps_clk + +Optional properties: +- clock-output-names : name of the output clock + +Example: + armpll: armpll { + #clock-cells = <0>; + compatible = "xlnx,zynq-pll"; + clocks = <&ps_clk>; + reg = <0x100 0x110>; + clock-output-names = "armpll"; + }; + +== Peripheral clocks == + +Describes clock node for the SDIO, SMC, SPI, QSPI, and UART clocks. + +Required properties: +- #clock-cells : shall be 1 +- compatible : "xlnx,zynq-periph-clock" +- reg : a single u32 value, describing the offset within the SLCR where + the CLK_CTRL register is found for this peripheral +- clocks : phandle for parent clocks. should hold phandles for + the IO_PLL, ARM_PLL, and DDR_PLL in order +- clock-output-names : names of the output clock(s). For peripherals that have + two output clocks (for example, the UART), two clocks + should be listed. + +Example: + uart_clk: uart_clk { + #clock-cells = <1>; + compatible = "xlnx,zynq-periph-clock"; + clocks = <&iopll &armpll &ddrpll>; + reg = <0x154>; + clock-output-names = "uart0_ref_clk", + "uart1_ref_clk"; + }; diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-spear.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-spear.txt new file mode 100644 index 00000000000..f3d44984d91 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-spear.txt @@ -0,0 +1,42 @@ +SPEAr cpufreq driver +------------------- + +SPEAr SoC cpufreq driver for CPU frequency scaling. +It supports both uniprocessor (UP) and symmetric multiprocessor (SMP) systems +which share clock across all CPUs. + +Required properties: +- cpufreq_tbl: Table of frequencies CPU could be transitioned into, in the + increasing order. + +Optional properties: +- clock-latency: Specify the possible maximum transition latency for clock, in + unit of nanoseconds. + +Both required and optional properties listed above must be defined under node +/cpus/cpu@0. + +Examples: +-------- +cpus { + + <...> + + cpu@0 { + compatible = "arm,cortex-a9"; + reg = <0>; + + <...> + + cpufreq_tbl = < 166000 + 200000 + 250000 + 300000 + 400000 + 500000 + 600000 >; + }; + + <...> + +}; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index bd7ce120bc1..fc9ce6f1688 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -54,7 +54,8 @@ PROPERTIES - compatible Usage: required Value type: <string> - Definition: Must include "fsl,sec-v4.0" + Definition: Must include "fsl,sec-v4.0". Also includes SEC + ERA versions (optional) with which the device is compatible. - #address-cells Usage: required @@ -106,7 +107,7 @@ PROPERTIES EXAMPLE crypto@300000 { - compatible = "fsl,sec-v4.0"; + compatible = "fsl,sec-v4.0", "fsl,sec-era-v2.0"; #address-cells = <1>; #size-cells = <1>; reg = <0x300000 0x10000>; diff --git a/Documentation/devicetree/bindings/dma/mv-xor.txt b/Documentation/devicetree/bindings/dma/mv-xor.txt new file mode 100644 index 00000000000..7c6cb7fcecd --- /dev/null +++ b/Documentation/devicetree/bindings/dma/mv-xor.txt @@ -0,0 +1,40 @@ +* Marvell XOR engines + +Required properties: +- compatible: Should be "marvell,orion-xor" +- reg: Should contain registers location and length (two sets) + the first set is the low registers, the second set the high + registers for the XOR engine. +- clocks: pointer to the reference clock + +The DT node must also contains sub-nodes for each XOR channel that the +XOR engine has. Those sub-nodes have the following required +properties: +- interrupts: interrupt of the XOR channel + +And the following optional properties: +- dmacap,memcpy to indicate that the XOR channel is capable of memcpy operations +- dmacap,memset to indicate that the XOR channel is capable of memset operations +- dmacap,xor to indicate that the XOR channel is capable of xor operations + +Example: + +xor@d0060900 { + compatible = "marvell,orion-xor"; + reg = <0xd0060900 0x100 + 0xd0060b00 0x100>; + clocks = <&coreclk 0>; + status = "okay"; + + xor00 { + interrupts = <51>; + dmacap,memcpy; + dmacap,xor; + }; + xor01 { + interrupts = <52>; + dmacap,memcpy; + dmacap,xor; + dmacap,memset; + }; +}; diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmi.txt b/Documentation/devicetree/bindings/drm/exynos/hdmi.txt new file mode 100644 index 00000000000..589edee3739 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/exynos/hdmi.txt @@ -0,0 +1,22 @@ +Device-Tree bindings for drm hdmi driver + +Required properties: +- compatible: value should be "samsung,exynos5-hdmi". +- reg: physical base address of the hdmi and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- hpd-gpio: following information about the hotplug gpio pin. + a) phandle of the gpio controller node. + b) pin number within the gpio controller. + c) pin function mode. + d) optional flags and pull up/down. + e) drive strength. + +Example: + + hdmi { + compatible = "samsung,exynos5-hdmi"; + reg = <0x14530000 0x100000>; + interrupts = <0 95 0>; + hpd-gpio = <&gpx3 7 0xf 1 3>; + }; diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt b/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt new file mode 100644 index 00000000000..fa166d94580 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt @@ -0,0 +1,12 @@ +Device-Tree bindings for hdmiddc driver + +Required properties: +- compatible: value should be "samsung,exynos5-hdmiddc". +- reg: I2C address of the hdmiddc device. + +Example: + + hdmiddc { + compatible = "samsung,exynos5-hdmiddc"; + reg = <0x50>; + }; diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt b/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt new file mode 100644 index 00000000000..858f4f9b902 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt @@ -0,0 +1,12 @@ +Device-Tree bindings for hdmiphy driver + +Required properties: +- compatible: value should be "samsung,exynos5-hdmiphy". +- reg: I2C address of the hdmiphy device. + +Example: + + hdmiphy { + compatible = "samsung,exynos5-hdmiphy"; + reg = <0x38>; + }; diff --git a/Documentation/devicetree/bindings/drm/exynos/mixer.txt b/Documentation/devicetree/bindings/drm/exynos/mixer.txt new file mode 100644 index 00000000000..9b2ea034356 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/exynos/mixer.txt @@ -0,0 +1,15 @@ +Device-Tree bindings for mixer driver + +Required properties: +- compatible: value should be "samsung,exynos5-mixer". +- reg: physical base address of the mixer and length of memory mapped + region. +- interrupts: interrupt number to the cpu. + +Example: + + mixer { + compatible = "samsung,exynos5-mixer"; + reg = <0x14450000 0x10000>; + interrupts = <0 94 0>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt new file mode 100644 index 00000000000..558cdf3c9ab --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt @@ -0,0 +1,22 @@ +GPIO line that should be set high/low to power off a device + +Required properties: +- compatible : should be "gpio-poweroff". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to power down the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- input : Initially configure the GPIO line as an input. Only reconfigure + it to an output when the pm_power_off function is called. If this optional + property is not specified, the GPIO is initialized as an output in its + inactive state. + + +Examples: + +gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 4 0>; /* GPIO 4 Active Low */ +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt b/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt new file mode 100644 index 00000000000..a0e4cf88521 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt @@ -0,0 +1,18 @@ +STMPE gpio +---------- + +Required properties: + - compatible: "st,stmpe-gpio" + +Optional properties: + - st,norequest-mask: bitmask specifying which GPIOs should _not_ be requestable + due to different usage (e.g. touch, keypad) + +Node name must be stmpe_gpio and should be child node of stmpe node to which it +belongs. + +Example: + stmpe_gpio { + compatible = "st,stmpe-gpio"; + st,norequest-mask = <0x20>; //gpio 5 can't be used + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 4e16ba4feab..a33628759d3 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -75,4 +75,40 @@ Example of two SOC GPIO banks defined as gpio-controller nodes: gpio-controller; }; +2.1) gpio-controller and pinctrl subsystem +------------------------------------------ +gpio-controller on a SOC might be tightly coupled with the pinctrl +subsystem, in the sense that the pins can be used by other functions +together with optional gpio feature. + +While the pin allocation is totally managed by the pin ctrl subsystem, +gpio (under gpiolib) is still maintained by gpio drivers. It may happen +that different pin ranges in a SoC is managed by different gpio drivers. + +This makes it logical to let gpio drivers announce their pin ranges to +the pin ctrl subsystem and call 'pinctrl_request_gpio' in order to +request the corresponding pin before any gpio usage. + +For this, the gpio controller can use a pinctrl phandle and pins to +announce the pinrange to the pin ctrl subsystem. For example, + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + gpio-ranges = <&pinctrl1 20 10>, <&pinctrl2 50 20>; + + } + +where, + &pinctrl1 and &pinctrl2 is the phandle to the pinctrl DT node. + + Next values specify the base pin and number of pins for the range + handled by 'qe_pio_e' gpio. In the given example from base pin 20 to + pin 29 under pinctrl1 and pin 50 to pin 69 under pinctrl2 is handled + by this gpio controller. + +The pinctrl node must have "#gpio-range-cells" property to show number of +arguments to pass with phandle from gpio controllers node. diff --git a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt index 66efc804806..85f8c0d084f 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt +++ b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt @@ -9,6 +9,10 @@ Required properties: unused). - gpio-controller: Marks the device node as a GPIO controller. +optional properties: +- #gpio-lines: Number of gpio if absent 32. + + Example: pioA: gpio@fffff200 { compatible = "atmel,at91rm9200-gpio"; @@ -16,5 +20,6 @@ Example: interrupts = <2 4>; #gpio-cells = <2>; gpio-controller; + #gpio-lines = <19>; }; diff --git a/Documentation/devicetree/bindings/gpio/leds-ns2.txt b/Documentation/devicetree/bindings/gpio/leds-ns2.txt new file mode 100644 index 00000000000..aef3aca34d2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/leds-ns2.txt @@ -0,0 +1,26 @@ +Binding for dual-GPIO LED found on Network Space v2 (and parents). + +Required properties: +- compatible: "lacie,ns2-leds". + +Each LED is represented as a sub-node of the ns2-leds device. + +Required sub-node properties: +- cmd-gpio: Command LED GPIO. See OF device-tree GPIO specification. +- slow-gpio: Slow LED GPIO. See OF device-tree GPIO specification. + +Optional sub-node properties: +- label: Name for this LED. If omitted, the label is taken from the node name. +- linux,default-trigger: Trigger assigned to the LED. + +Example: + +ns2-leds { + compatible = "lacie,ns2-leds"; + + blue-sata { + label = "ns2:blue:sata"; + slow-gpio = <&gpio0 29 0>; + cmd-gpio = <&gpio0 30 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpio/spear_spics.txt b/Documentation/devicetree/bindings/gpio/spear_spics.txt new file mode 100644 index 00000000000..96c37eb1507 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/spear_spics.txt @@ -0,0 +1,50 @@ +=== ST Microelectronics SPEAr SPI CS Driver === + +SPEAr platform provides a provision to control chipselects of ARM PL022 Prime +Cell spi controller through its system registers, which otherwise remains under +PL022 control. If chipselect remain under PL022 control then they would be +released as soon as transfer is over and TxFIFO becomes empty. This is not +desired by some of the device protocols above spi which expect (multiple) +transfers without releasing their chipselects. + +Chipselects can be controlled by software by turning them as GPIOs. SPEAr +provides another interface through system registers through which software can +directly control each PL022 chipselect. Hence, it is natural for SPEAr to export +the control of this interface as gpio. + +Required properties: + + * compatible: should be defined as "st,spear-spics-gpio" + * reg: mentioning address range of spics controller + * st-spics,peripcfg-reg: peripheral configuration register offset + * st-spics,sw-enable-bit: bit offset to enable sw control + * st-spics,cs-value-bit: bit offset to drive chipselect low or high + * st-spics,cs-enable-mask: chip select number bit mask + * st-spics,cs-enable-shift: chip select number program offset + * gpio-controller: Marks the device node as gpio controller + * #gpio-cells: should be 1 and will mention chip select number + +All the above bit offsets are within peripcfg register. + +Example: +------- +spics: spics@e0700000{ + compatible = "st,spear-spics-gpio"; + reg = <0xe0700000 0x1000>; + st-spics,peripcfg-reg = <0x3b0>; + st-spics,sw-enable-bit = <12>; + st-spics,cs-value-bit = <11>; + st-spics,cs-enable-mask = <3>; + st-spics,cs-enable-shift = <8>; + gpio-controller; + #gpio-cells = <2>; +}; + + +spi0: spi@e0100000 { + status = "okay"; + num-cs = <3>; + cs-gpios = <&gpio1 7 0>, <&spics 0>, + <&spics 1>; + ... +} diff --git a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt new file mode 100644 index 00000000000..b4fa934ae3a --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt @@ -0,0 +1,191 @@ +NVIDIA Tegra host1x + +Required properties: +- compatible: "nvidia,tegra<chip>-host1x" +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt outputs from the controller. +- #address-cells: The number of cells used to represent physical base addresses + in the host1x address space. Should be 1. +- #size-cells: The number of cells used to represent the size of an address + range in the host1x address space. Should be 1. +- ranges: The mapping of the host1x address space to the CPU address space. + +The host1x top-level node defines a number of children, each representing one +of the following host1x client modules: + +- mpe: video encoder + + Required properties: + - compatible: "nvidia,tegra<chip>-mpe" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- vi: video input + + Required properties: + - compatible: "nvidia,tegra<chip>-vi" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- epp: encoder pre-processor + + Required properties: + - compatible: "nvidia,tegra<chip>-epp" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- isp: image signal processor + + Required properties: + - compatible: "nvidia,tegra<chip>-isp" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- gr2d: 2D graphics engine + + Required properties: + - compatible: "nvidia,tegra<chip>-gr2d" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- gr3d: 3D graphics engine + + Required properties: + - compatible: "nvidia,tegra<chip>-gr3d" + - reg: Physical base address and length of the controller's registers. + +- dc: display controller + + Required properties: + - compatible: "nvidia,tegra<chip>-dc" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + + Each display controller node has a child node, named "rgb", that represents + the RGB output associated with the controller. It can take the following + optional properties: + - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection + - nvidia,edid: supplies a binary EDID blob + +- hdmi: High Definition Multimedia Interface + + Required properties: + - compatible: "nvidia,tegra<chip>-hdmi" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + - vdd-supply: regulator for supply voltage + - pll-supply: regulator for PLL + + Optional properties: + - nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - nvidia,hpd-gpio: specifies a GPIO used for hotplug detection + - nvidia,edid: supplies a binary EDID blob + +- tvo: TV encoder output + + Required properties: + - compatible: "nvidia,tegra<chip>-tvo" + - reg: Physical base address and length of the controller's registers. + - interrupts: The interrupt outputs from the controller. + +- dsi: display serial interface + + Required properties: + - compatible: "nvidia,tegra<chip>-dsi" + - reg: Physical base address and length of the controller's registers. + +Example: + +/ { + ... + + host1x { + compatible = "nvidia,tegra20-host1x", "simple-bus"; + reg = <0x50000000 0x00024000>; + interrupts = <0 65 0x04 /* mpcore syncpt */ + 0 67 0x04>; /* mpcore general */ + + #address-cells = <1>; + #size-cells = <1>; + + ranges = <0x54000000 0x54000000 0x04000000>; + + mpe { + compatible = "nvidia,tegra20-mpe"; + reg = <0x54040000 0x00040000>; + interrupts = <0 68 0x04>; + }; + + vi { + compatible = "nvidia,tegra20-vi"; + reg = <0x54080000 0x00040000>; + interrupts = <0 69 0x04>; + }; + + epp { + compatible = "nvidia,tegra20-epp"; + reg = <0x540c0000 0x00040000>; + interrupts = <0 70 0x04>; + }; + + isp { + compatible = "nvidia,tegra20-isp"; + reg = <0x54100000 0x00040000>; + interrupts = <0 71 0x04>; + }; + + gr2d { + compatible = "nvidia,tegra20-gr2d"; + reg = <0x54140000 0x00040000>; + interrupts = <0 72 0x04>; + }; + + gr3d { + compatible = "nvidia,tegra20-gr3d"; + reg = <0x54180000 0x00040000>; + }; + + dc@54200000 { + compatible = "nvidia,tegra20-dc"; + reg = <0x54200000 0x00040000>; + interrupts = <0 73 0x04>; + + rgb { + status = "disabled"; + }; + }; + + dc@54240000 { + compatible = "nvidia,tegra20-dc"; + reg = <0x54240000 0x00040000>; + interrupts = <0 74 0x04>; + + rgb { + status = "disabled"; + }; + }; + + hdmi { + compatible = "nvidia,tegra20-hdmi"; + reg = <0x54280000 0x00040000>; + interrupts = <0 75 0x04>; + status = "disabled"; + }; + + tvo { + compatible = "nvidia,tegra20-tvo"; + reg = <0x542c0000 0x00040000>; + interrupts = <0 76 0x04>; + status = "disabled"; + }; + + dsi { + compatible = "nvidia,tegra20-dsi"; + reg = <0x54300000 0x00040000>; + status = "disabled"; + }; + }; + + ... +}; diff --git a/Documentation/devicetree/bindings/hwmon/vexpress.txt b/Documentation/devicetree/bindings/hwmon/vexpress.txt new file mode 100644 index 00000000000..9c27ed694bb --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/vexpress.txt @@ -0,0 +1,23 @@ +Versatile Express hwmon sensors +------------------------------- + +Requires node properties: +- "compatible" value : one of + "arm,vexpress-volt" + "arm,vexpress-amp" + "arm,vexpress-temp" + "arm,vexpress-power" + "arm,vexpress-energy" +- "arm,vexpress-sysreg,func" when controlled via vexpress-sysreg + (see Documentation/devicetree/bindings/arm/vexpress-sysreg.txt + for more details) + +Optional node properties: +- label : string describing the monitored value + +Example: + energy@0 { + compatible = "arm,vexpress-energy"; + arm,vexpress-sysreg,func = <13 0>; + label = "A15 Jcore"; + }; diff --git a/Documentation/devicetree/bindings/i2c/atmel-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-at91.txt index b689a0d9441..b689a0d9441 100644 --- a/Documentation/devicetree/bindings/i2c/atmel-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-at91.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt new file mode 100644 index 00000000000..8ce9cd2855b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt @@ -0,0 +1,27 @@ +Device tree bindings for i2c-cbus-gpio driver + +Required properties: + - compatible = "i2c-cbus-gpio"; + - gpios: clk, dat, sel + - #address-cells = <1>; + - #size-cells = <0>; + +Optional properties: + - child nodes conforming to i2c bus binding + +Example: + +i2c@0 { + compatible = "i2c-cbus-gpio"; + gpios = <&gpio 66 0 /* clk */ + &gpio 65 0 /* dat */ + &gpio 64 0 /* sel */ + >; + #address-cells = <1>; + #size-cells = <0>; + + retu-mfd: retu@1 { + compatible = "retu-mfd"; + reg = <0x1>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/davinci.txt b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt index 2dc935b4113..2dc935b4113 100644 --- a/Documentation/devicetree/bindings/i2c/davinci.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt diff --git a/Documentation/devicetree/bindings/i2c/gpio-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-gpio.txt index 4f8ec947c6b..4f8ec947c6b 100644 --- a/Documentation/devicetree/bindings/i2c/gpio-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-gpio.txt diff --git a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index f3cf43b66f7..3614242e773 100644 --- a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -12,13 +12,13 @@ Optional properties: Examples: i2c@83fc4000 { /* I2C2 on i.MX51 */ - compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + compatible = "fsl,imx51-i2c", "fsl,imx21-i2c"; reg = <0x83fc4000 0x4000>; interrupts = <63>; }; i2c@70038000 { /* HS-I2C on i.MX51 */ - compatible = "fsl,imx51-i2c", "fsl,imx1-i2c"; + compatible = "fsl,imx51-i2c", "fsl,imx21-i2c"; reg = <0x70038000 0x4000>; interrupts = <64>; clock-frequency = <400000>; diff --git a/Documentation/devicetree/bindings/i2c/fsl-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt index 1eacd6b20ed..1eacd6b20ed 100644 --- a/Documentation/devicetree/bindings/i2c/fsl-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt new file mode 100644 index 00000000000..66709a82554 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt @@ -0,0 +1,81 @@ +GPIO-based I2C Bus Mux + +This binding describes an I2C bus multiplexer that uses GPIOs to +route the I2C signals. + + +-----+ +-----+ + | dev | | dev | + +------------+ +-----+ +-----+ + | SoC | | | + | | /--------+--------+ + | +------+ | +------+ child bus A, on GPIO value set to 0 + | | I2C |-|--| Mux | + | +------+ | +--+---+ child bus B, on GPIO value set to 1 + | | | \----------+--------+--------+ + | +------+ | | | | | + | | GPIO |-|-----+ +-----+ +-----+ +-----+ + | +------+ | | dev | | dev | | dev | + +------------+ +-----+ +-----+ +-----+ + +Required properties: +- compatible: i2c-mux-gpio +- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side + port is connected to. +- mux-gpios: list of gpios used to control the muxer +* Standard I2C mux properties. See mux.txt in this directory. +* I2C child bus nodes. See mux.txt in this directory. + +Optional properties: +- idle-state: value to set the muxer to when idle. When no value is + given, it defaults to the last value used. + +For each i2c child node, an I2C child bus will be created. They will +be numbered based on their order in the device tree. + +Whenever an access is made to a device on a child bus, the value set +in the revelant node's reg property will be output using the list of +GPIOs, the first in the list holding the least-significant value. + +If an idle state is defined, using the idle-state (optional) property, +whenever an access is not being made to a device on a child bus, the +GPIOs will be set according to the idle value. + +If an idle state is not defined, the most recently used value will be +left programmed into hardware whenever no access is being made to a +device on a child bus. + +Example: + i2cmux { + compatible = "i2c-mux-gpio"; + #address-cells = <1>; + #size-cells = <0>; + mux-gpios = <&gpio1 22 0 &gpio1 23 0>; + i2c-parent = <&i2c1>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7 1>; + reset-active-low; + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555: pca9555@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/mux.txt b/Documentation/devicetree/bindings/i2c/i2c-mux.txt index af84cce5cd7..af84cce5cd7 100644 --- a/Documentation/devicetree/bindings/i2c/mux.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt new file mode 100644 index 00000000000..f46d928aa73 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt @@ -0,0 +1,18 @@ + +* Marvell MV64XXX I2C controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : Should be "marvell,mv64xxx-i2c" + - interrupts : The interrupt number + - clock-frequency : Desired I2C bus clock frequency in Hz. + +Examples: + + i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/nomadik.txt b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt index 72065b0ff68..72065b0ff68 100644 --- a/Documentation/devicetree/bindings/i2c/nomadik.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt index c15781f4dc8..1637c298a1b 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt @@ -1,7 +1,7 @@ Device tree configuration for i2c-ocores Required properties: -- compatible : "opencores,i2c-ocores" +- compatible : "opencores,i2c-ocores" or "aeroflexgaisler,i2cmst" - reg : bus address start and address range size of device - interrupts : interrupt number - clock-frequency : frequency of bus clock in Hz diff --git a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt index dced82ebe31..dced82ebe31 100644 --- a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt diff --git a/Documentation/devicetree/bindings/i2c/omap-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-omap.txt index 56564aa4b44..56564aa4b44 100644 --- a/Documentation/devicetree/bindings/i2c/omap-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-omap.txt diff --git a/Documentation/devicetree/bindings/i2c/pnx.txt b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt index fe98ada33ee..fe98ada33ee 100644 --- a/Documentation/devicetree/bindings/i2c/pnx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt diff --git a/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt index 569b1624851..569b1624851 100644 --- a/Documentation/devicetree/bindings/i2c/ce4100-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt diff --git a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt index 0f7945019f6..12b78ac507e 100644 --- a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt @@ -31,21 +31,3 @@ Examples: reg = <0xd4025000 0x1000>; interrupts = <58>; }; - -* Marvell MV64XXX I2C controller - -Required properties : - - - reg : Offset and length of the register set for the device - - compatible : Should be "marvell,mv64xxx-i2c" - - interrupts : The interrupt number - - clock-frequency : Desired I2C bus clock frequency in Hz. - -Examples: - - i2c@11000 { - compatible = "marvell,mv64xxx-i2c"; - reg = <0x11000 0x20>; - interrupts = <29>; - clock-frequency = <100000>; - }; diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt index b6cb5a12c67..e9611ace879 100644 --- a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -13,11 +13,17 @@ Required properties: - interrupts: interrupt number to the cpu. - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges. +Required for all cases except "samsung,s3c2440-hdmiphy-i2c": + - Samsung GPIO variant (deprecated): + - gpios: The order of the gpios should be the following: <SDA, SCL>. + The gpio specifier depends on the gpio controller. Required in all + cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output + lines are permanently wired to the respective clienta + - Pinctrl variant (preferred, if available): + - pinctrl-0: Pin control group to be used for this controller. + - pinctrl-names: Should contain only one value - "default". + Optional properties: - - gpios: The order of the gpios should be the following: <SDA, SCL>. - The gpio specifier depends on the gpio controller. Required in all - cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output - lines are permanently wired to the respective client - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not specified, default value is 0. - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not @@ -31,8 +37,14 @@ Example: interrupts = <345>; samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <100000>; + /* Samsung GPIO variant begins here */ gpios = <&gpd1 2 0 /* SDA */ &gpd1 3 0 /* SCL */>; + /* Samsung GPIO variant ends here */ + /* Pinctrl variant begins here */ + pinctrl-0 = <&i2c3_bus>; + pinctrl-names = "default"; + /* Pinctrl variant ends here */ #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/i2c/sirf-i2c.txt b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt index 7baf9e133fa..7baf9e133fa 100644 --- a/Documentation/devicetree/bindings/i2c/sirf-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt diff --git a/Documentation/devicetree/bindings/i2c/arm-versatile.txt b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt index 361d31c51b6..361d31c51b6 100644 --- a/Documentation/devicetree/bindings/i2c/arm-versatile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt diff --git a/Documentation/devicetree/bindings/i2c/xiic.txt b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt index ceabbe91ae4..ceabbe91ae4 100644 --- a/Documentation/devicetree/bindings/i2c/xiic.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 2f5322b119e..446859fcdca 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -55,5 +55,7 @@ st-micro,24c256 i2c serial eeprom (24cxx) stm,m41t00 Serial Access TIMEKEEPER stm,m41t62 Serial real-time clock (RTC) with alarm stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS +taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface +ti,tmp275 Digital Temperature Sensor diff --git a/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt new file mode 100644 index 00000000000..ead641c65e0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt @@ -0,0 +1,46 @@ +* GPIO driven matrix keypad device tree bindings + +GPIO driven matrix keypad is used to interface a SoC with a matrix keypad. +The matrix keypad supports multiple row and column lines, a key can be +placed at each intersection of a unique row and a unique column. The matrix +keypad can sense a key-press and key-release by means of GPIO lines and +report the event using GPIO interrupts to the cpu. + +Required Properties: +- compatible: Should be "gpio-matrix-keypad" +- row-gpios: List of gpios used as row lines. The gpio specifier + for this property depends on the gpio controller to + which these row lines are connected. +- col-gpios: List of gpios used as column lines. The gpio specifier + for this property depends on the gpio controller to + which these column lines are connected. +- linux,keymap: The definition can be found at + bindings/input/matrix-keymap.txt + +Optional Properties: +- linux,no-autorepeat: do no enable autorepeat feature. +- linux,wakeup: use any event on keypad as wakeup event. +- debounce-delay-ms: debounce interval in milliseconds +- col-scan-delay-us: delay, measured in microseconds, that is needed + before we can scan keypad after activating column gpio + +Example: + matrix-keypad { + compatible = "gpio-matrix-keypad"; + debounce-delay-ms = <5>; + col-scan-delay-us = <2>; + + row-gpios = <&gpio2 25 0 + &gpio2 26 0 + &gpio2 27 0>; + + col-gpios = <&gpio2 21 0 + &gpio2 22 0>; + + linux,keymap = <0x0000008B + 0x0100009E + 0x02000069 + 0x0001006A + 0x0101001C + 0x0201006C>; + }; diff --git a/Documentation/devicetree/bindings/input/pwm-beeper.txt b/Documentation/devicetree/bindings/input/pwm-beeper.txt new file mode 100644 index 00000000000..be332ae4f2d --- /dev/null +++ b/Documentation/devicetree/bindings/input/pwm-beeper.txt @@ -0,0 +1,7 @@ +* PWM beeper device tree bindings + +Registers a PWM device as beeper. + +Required properties: +- compatible: should be "pwm-beeper" +- pwms: phandle to the physical PWM device diff --git a/Documentation/devicetree/bindings/input/stmpe-keypad.txt b/Documentation/devicetree/bindings/input/stmpe-keypad.txt new file mode 100644 index 00000000000..1b97222e8a0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/stmpe-keypad.txt @@ -0,0 +1,39 @@ +* STMPE Keypad + +Required properties: + - compatible : "st,stmpe-keypad" + - linux,keymap : See ./matrix-keymap.txt + +Optional properties: + - debounce-interval : Debouncing interval time in milliseconds + - st,scan-count : Scanning cycles elapsed before key data is updated + - st,no-autorepeat : If specified device will not autorepeat + +Example: + + stmpe_keypad { + compatible = "st,stmpe-keypad"; + + debounce-interval = <64>; + st,scan-count = <8>; + st,no-autorepeat; + + linux,keymap = <0x205006b + 0x4010074 + 0x3050072 + 0x1030004 + 0x502006a + 0x500000a + 0x5008b + 0x706001c + 0x405000b + 0x6070003 + 0x3040067 + 0x303006c + 0x60400e7 + 0x602009e + 0x4020073 + 0x5050002 + 0x4030069 + 0x3020008>; + }; diff --git a/Documentation/devicetree/bindings/input/tca8418_keypad.txt b/Documentation/devicetree/bindings/input/tca8418_keypad.txt new file mode 100644 index 00000000000..2a1538f0053 --- /dev/null +++ b/Documentation/devicetree/bindings/input/tca8418_keypad.txt @@ -0,0 +1,8 @@ + +Required properties: +- compatible: "ti,tca8418" +- reg: the I2C address +- interrupts: IRQ line number, should trigger on falling edge +- keypad,num-rows: The number of rows +- keypad,num-columns: The number of columns +- linux,keymap: Keys definitions, see keypad-matrix. diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt new file mode 100644 index 00000000000..ca5a2c86480 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt @@ -0,0 +1,28 @@ +* Rohm BU21013 Touch Screen + +Required properties: + - compatible : "rohm,bu21013_tp" + - reg : I2C device address + +Optional properties: + - touch-gpio : GPIO pin registering a touch event + - <supply_name>-supply : Phandle to a regulator supply + - rohm,touch-max-x : Maximum outward permitted limit in the X axis + - rohm,touch-max-y : Maximum outward permitted limit in the Y axis + - rohm,flip-x : Flip touch coordinates on the X axis + - rohm,flip-y : Flip touch coordinates on the Y axis + +Example: + + i2c@80110000 { + bu21013_tp@0x5c { + compatible = "rohm,bu21013_tp"; + reg = <0x5c>; + touch-gpio = <&gpio2 20 0x4>; + avdd-supply = <&ab8500_ldo_aux1_reg>; + + rohm,touch-max-x = <384>; + rohm,touch-max-y = <704>; + rohm,flip-y; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt new file mode 100644 index 00000000000..df70318a617 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt @@ -0,0 +1,19 @@ +* EETI eGalax Multiple Touch Controller + +Required properties: +- compatible: must be "eeti,egalax_ts" +- reg: i2c slave address +- interrupt-parent: the phandle for the interrupt controller +- interrupts: touch controller interrupt +- wakeup-gpios: the gpio pin to be used for waking up the controller + as well as uased as irq pin + +Example: + + egalax_ts@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <9 2>; + wakeup-gpios = <&gpio1 9 0>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/mms114.txt b/Documentation/devicetree/bindings/input/touchscreen/mms114.txt new file mode 100644 index 00000000000..89d4c56c567 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/mms114.txt @@ -0,0 +1,34 @@ +* MELFAS MMS114 touchscreen controller + +Required properties: +- compatible: must be "melfas,mms114" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Optional properties: +- contact-threshold: +- moving-threshold: +- x-invert: invert X axis +- y-invert: invert Y axis + +Example: + + i2c@00000000 { + /* ... */ + + touchscreen@48 { + compatible = "melfas,mms114"; + reg = <0x48>; + interrupts = <39 0>; + x-size = <720>; + y-size = <1280>; + contact-threshold = <10>; + moving-threshold = <10>; + x-invert; + y-invert; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt new file mode 100644 index 00000000000..127baa31a77 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt @@ -0,0 +1,43 @@ +STMPE Touchscreen +---------------- + +Required properties: + - compatible: "st,stmpe-ts" + +Optional properties: +- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 -> + 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6 + -> 144 clocks), recommended is 4. +- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) +- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external + reference) +- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) +- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 + samples, 3 -> 8 samples) +- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 -> + 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended + is 3 +- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 + -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2 +- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of + the fractional part) recommended is 7 +- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35 + mA max, 1 -> 50 mA typical 80 mA max) + +Node name must be stmpe_touchscreen and should be child node of stmpe node to +which it belongs. + +Example: + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + st,sample-time = <4>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,adc-freq = <1>; + st,ave-ctrl = <1>; + st,touch-det-delay = <2>; + st,settling = <2>; + st,fraction-z = <7>; + st,i-drive = <1>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-ic.txt new file mode 100644 index 00000000000..7f9fb85f545 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-ic.txt @@ -0,0 +1,104 @@ +Allwinner Sunxi Interrupt Controller + +Required properties: + +- compatible : should be "allwinner,sunxi-ic" +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + +The interrupt sources are as follows: + +0: ENMI +1: UART0 +2: UART1 +3: UART2 +4: UART3 +5: IR0 +6: IR1 +7: I2C0 +8: I2C1 +9: I2C2 +10: SPI0 +11: SPI1 +12: SPI2 +13: SPDIF +14: AC97 +15: TS +16: I2S +17: UART4 +18: UART5 +19: UART6 +20: UART7 +21: KEYPAD +22: TIMER0 +23: TIMER1 +24: TIMER2 +25: TIMER3 +26: CAN +27: DMA +28: PIO +29: TOUCH_PANEL +30: AUDIO_CODEC +31: LRADC +32: SDMC0 +33: SDMC1 +34: SDMC2 +35: SDMC3 +36: MEMSTICK +37: NAND +38: USB0 +39: USB1 +40: USB2 +41: SCR +42: CSI0 +43: CSI1 +44: LCDCTRL0 +45: LCDCTRL1 +46: MP +47: DEFEBE0 +48: DEFEBE1 +49: PMU +50: SPI3 +51: TZASC +52: PATA +53: VE +54: SS +55: EMAC +56: SATA +57: GPS +58: HDMI +59: TVE +60: ACE +61: TVD +62: PS2_0 +63: PS2_1 +64: USB3 +65: USB4 +66: PLE_PFM +67: TIMER4 +68: TIMER5 +69: GPU_GP +70: GPU_GPMMU +71: GPU_PP0 +72: GPU_PPMMU0 +73: GPU_PMU +74: GPU_RSV0 +75: GPU_RSV1 +76: GPU_RSV2 +77: GPU_RSV3 +78: GPU_RSV4 +79: GPU_RSV5 +80: GPU_RSV6 +82: SYNC_TIMER0 +83: SYNC_TIMER1 + +Example: + +intc: interrupt-controller { + compatible = "allwinner,sunxi-ic"; + reg = <0x01c20400 0x400>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt new file mode 100644 index 00000000000..2d88816dd55 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -0,0 +1,23 @@ +Common leds properties. + +Optional properties for child nodes: +- label : The label for this LED. If omitted, the label is + taken from the node name (excluding the unit address). + +- linux,default-trigger : This parameter, if present, is a + string defining the trigger assigned to the LED. Current triggers are: + "backlight" - LED will act as a back-light, controlled by the framebuffer + system + "default-on" - LED will turn on (but for leds-gpio see "default-state" + property in Documentation/devicetree/bindings/gpio/led.txt) + "heartbeat" - LED "double" flashes at a load average based rate + "ide-disk" - LED indicates disk activity + "timer" - LED flashes at a fixed, configurable rate + +Examples: + +system-status { + label = "Status"; + linux,default-trigger = "heartbeat"; + ... +}; diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/leds/leds-gpio.txt index edc83c1c0d5..df1b3080f6b 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/leds/leds-gpio.txt @@ -10,16 +10,10 @@ LED sub-node properties: - gpios : Should specify the LED's GPIO, see "gpios property" in Documentation/devicetree/bindings/gpio/gpio.txt. Active low LEDs should be indicated using flags in the GPIO specifier. -- label : (optional) The label for this LED. If omitted, the label is - taken from the node name (excluding the unit address). -- linux,default-trigger : (optional) This parameter, if present, is a - string defining the trigger assigned to the LED. Current triggers are: - "backlight" - LED will act as a back-light, controlled by the framebuffer - system - "default-on" - LED will turn on, but see "default-state" below - "heartbeat" - LED "double" flashes at a load average based rate - "ide-disk" - LED indicates disk activity - "timer" - LED flashes at a fixed, configurable rate +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt - default-state: (optional) The initial state of the LED. Valid values are "on", "off", and "keep". If the LED is already on or off and the default-state property is set the to same value, then no diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt new file mode 100644 index 00000000000..67ec3d4ccc7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -0,0 +1,23 @@ +* Samsung Multi Format Codec (MFC) + +Multi Format Codec (MFC) is the IP present in Samsung SoCs which +supports high resolution decoding and encoding functionalities. +The MFC device driver is a v4l2 driver which can encode/decode +video raw/elementary streams and has support for all popular +video codecs. + +Required properties: + - compatible : value should be either one among the following + (a) "samsung,mfc-v5" for MFC v5 present in Exynos4 SoCs + (b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : MFC interrupt number to the CPU. + + - samsung,mfc-r : Base address of the first memory bank used by MFC + for DMA contiguous memory allocation and its size. + + - samsung,mfc-l : Base address of the second memory bank used by MFC + for DMA contiguous memory allocation and its size. diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt index ce83c8d3c00..13b707b7355 100644 --- a/Documentation/devicetree/bindings/mfd/ab8500.txt +++ b/Documentation/devicetree/bindings/mfd/ab8500.txt @@ -24,7 +24,32 @@ ab8500-bm : : : Battery Manager ab8500-btemp : : : Battery Temperature ab8500-charger : : : Battery Charger ab8500-codec : : : Audio Codec -ab8500-fg : : : Fuel Gauge +ab8500-fg : : vddadc : Fuel Gauge + : NCONV_ACCU : : Accumulate N Sample Conversion + : BATT_OVV : : Battery Over Voltage + : LOW_BAT_F : : LOW threshold battery voltage + : CC_INT_CALIB : : Coulomb Counter Internal Calibration + : CCEOC : : Coulomb Counter End of Conversion +ab8500-btemp : : vtvout : Battery Temperature + : BAT_CTRL_INDB : : Battery Removal Indicator + : BTEMP_LOW : : Btemp < BtempLow, if battery temperature is lower than -10°C + : BTEMP_LOW_MEDIUM : : BtempLow < Btemp < BtempMedium,if battery temperature is between -10 and 0°C + : BTEMP_MEDIUM_HIGH : : BtempMedium < Btemp < BtempHigh,if battery temperature is between 0°C and“MaxTemp + : BTEMP_HIGH : : Btemp > BtempHigh, if battery temperature is higher than “MaxTemp +ab8500-charger : : vddadc : Charger interface + : MAIN_CH_UNPLUG_DET : : main charger unplug detection management (not in 8505) + : MAIN_CHARGE_PLUG_DET : : main charger plug detection management (not in 8505) + : MAIN_EXT_CH_NOT_OK : : main charger not OK + : MAIN_CH_TH_PROT_R : : Die temp is above main charger + : MAIN_CH_TH_PROT_F : : Die temp is below main charger + : VBUS_DET_F : : VBUS falling detected + : VBUS_DET_R : : VBUS rising detected + : USB_LINK_STATUS : : USB link status has changed + : USB_CH_TH_PROT_R : : Die temp is above usb charger + : USB_CH_TH_PROT_F : : Die temp is below usb charger + : USB_CHARGER_NOT_OKR : : allowed USB charger not ok detection + : VBUS_OVV : : Overvoltage on Vbus ball detected (USB charge is stopped) + : CH_WD_EXP : : Charger watchdog detected ab8500-gpadc : HW_CONV_END : vddadc : Analogue to Digital Converter SW_CONV_END : : ab8500-gpio : : : GPIO Controller diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt new file mode 100644 index 00000000000..56edb552068 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -0,0 +1,28 @@ +* ST Microelectronics STMPE Multi-Functional Device + +STMPE is an MFD device which may expose the following inbuilt devices: gpio, +keypad, touchscreen, adc, pwm, rotator. + +Required properties: + - compatible : "st,stmpe[610|801|811|1601|2401|2403]" + - reg : I2C/SPI address of the device + +Optional properties: + - interrupts : The interrupt outputs from the controller + - interrupt-controller : Marks the device node as an interrupt controller + - interrupt-parent : Specifies which IRQ controller we're connected to + - wakeup-source : Marks the input device as wakable + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + +Example: + + stmpe1601: stmpe1601@40 { + compatible = "st,stmpe1601"; + reg = <0x40>; + interrupts = <26 0x4>; + interrupt-parent = <&gpio6>; + interrupt-controller; + + wakeup-source; + st,autosleep-timeout = <1024>; + }; diff --git a/Documentation/devicetree/bindings/misc/atmel-ssc.txt b/Documentation/devicetree/bindings/misc/atmel-ssc.txt new file mode 100644 index 00000000000..38e51ad2e07 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/atmel-ssc.txt @@ -0,0 +1,15 @@ +* Atmel SSC driver. + +Required properties: +- compatible: "atmel,at91rm9200-ssc" or "atmel,at91sam9g45-ssc" + - atmel,at91rm9200-ssc: support pdc transfer + - atmel,at91sam9g45-ssc: support dma transfer +- reg: Should contain SSC registers location and length +- interrupts: Should contain SSC interrupt + +Example: +ssc0: ssc@fffbc000 { + compatible = "atmel,at91rm9200-ssc"; + reg = <0xfffbc000 0x4000>; + interrupts = <14 4 5>; +}; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 8e2e0ba2f48..a591c6741d7 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -21,6 +21,12 @@ Optional properties: - cd-inverted: when present, polarity on the cd gpio line is inverted - wp-inverted: when present, polarity on the wp gpio line is inverted - max-frequency: maximum operating clock frequency +- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on + this system, even if the controller claims it is. + +Optional SDIO properties: +- keep-power-in-suspend: Preserves card power during a suspend/resume cycle +- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion Example: @@ -33,4 +39,6 @@ sdhci@ab000000 { cd-inverted; wp-gpios = <&gpio 70 0>; max-frequency = <50000000>; + keep-power-in-suspend; + enable-sdio-wakeup; } diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt index 630a7d7f471..97e9e315400 100644 --- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -12,10 +12,6 @@ is used. The Samsung's SDHCI controller bindings extends this as listed below. [A] The property "samsung,cd-pinmux-gpio" can be used as stated in the "Optional Board Specific Properties" section below. -[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property - is not specified, it is assumed that there is no card detection - mechanism used. - Required SoC Specific Properties: - compatible: should be one of the following - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci @@ -24,14 +20,18 @@ Required SoC Specific Properties: controller. Required Board Specific Properties: -- gpios: Should specify the gpios used for clock, command and data lines. The - gpio specifier format depends on the gpio controller. +- Samsung GPIO variant (will be completely replaced by pinctrl): + - gpios: Should specify the gpios used for clock, command and data lines. The + gpio specifier format depends on the gpio controller. +- Pinctrl variant (preferred if available): + - pinctrl-0: Should specify pin control groups used for this controller. + - pinctrl-names: Should contain only one value - "default". Optional Board Specific Properties: - samsung,cd-pinmux-gpio: Specifies the card detect line that is routed through a pinmux to the card-detect pin of the card slot. This property should be used only if none of the mmc core card-detect properties are - used. + used. Only for Samsung GPIO variant. Example: sdhci@12530000 { @@ -40,12 +40,18 @@ Example: interrupts = <0 75 0>; bus-width = <4>; cd-gpios = <&gpk2 2 2 3 3>; + + /* Samsung GPIO variant */ gpios = <&gpk2 0 2 0 3>, /* clock line */ <&gpk2 1 2 0 3>, /* command line */ <&gpk2 3 2 3 3>, /* data line 0 */ <&gpk2 4 2 3 3>, /* data line 1 */ <&gpk2 5 2 3 3>, /* data line 2 */ <&gpk2 6 2 3 3>; /* data line 3 */ + + /* Pinctrl variant */ + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>; + pinctrl-names = "default"; }; Note: This example shows both SoC specific and board specific properties diff --git a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt index 06cd32d0805..06cd32d0805 100644 --- a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index be76a23b34c..ed271fc255b 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -19,6 +19,7 @@ ti,dual-volt: boolean, supports dual voltage cards "supply-name" examples are "vmmc", "vmmc_aux" etc ti,non-removable: non-removable slot (like eMMC) ti,needs-special-reset: Requires a special softreset sequence +ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed Example: mmc1: mmc@0x4809c000 { diff --git a/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt new file mode 100644 index 00000000000..d7fb6abb3eb --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt @@ -0,0 +1,23 @@ +* Wondermedia WM8505/WM8650 SD/MMC Host Controller + +This file documents differences between the core properties described +by mmc.txt and the properties used by the wmt-sdmmc driver. + +Required properties: +- compatible: Should be "wm,wm8505-sdhc". +- interrupts: Two interrupts are required - regular irq and dma irq. + +Optional properties: +- sdon-inverted: SD_ON bit is inverted on the controller + +Examples: + +sdhc@d800a000 { + compatible = "wm,wm8505-sdhc"; + reg = <0xd800a000 0x1000>; + interrupts = <20 21>; + clocks = <&sdhc>; + bus-width = <4>; + sdon-inverted; +}; + diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt new file mode 100644 index 00000000000..b04d03a1d49 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt @@ -0,0 +1,23 @@ +* Denali NAND controller + +Required properties: + - compatible : should be "denali,denali-nand-dt" + - reg : should contain registers location and length for data and reg. + - reg-names: Should contain the reg names "nand_data" and "denali_reg" + - interrupts : The interrupt number. + - dm-mask : DMA bit mask + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Examples: + +nand: nand@ff900000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "denali,denali-nand-dt"; + reg = <0xff900000 0x100000>, <0xffb80000 0x10000>; + reg-names = "nand_data", "denali_reg"; + interrupts = <0 144 4>; + dma-mask = <0xffffffff>; +}; diff --git a/Documentation/devicetree/bindings/mtd/flctl-nand.txt b/Documentation/devicetree/bindings/mtd/flctl-nand.txt new file mode 100644 index 00000000000..427f46dc60a --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/flctl-nand.txt @@ -0,0 +1,49 @@ +FLCTL NAND controller + +Required properties: +- compatible : "renesas,shmobile-flctl-sh7372" +- reg : Address range of the FLCTL +- interrupts : flste IRQ number +- nand-bus-width : bus width to NAND chip + +Optional properties: +- dmas: DMA specifier(s) +- dma-names: name for each DMA specifier. Valid names are + "data_tx", "data_rx", "ecc_tx", "ecc_rx" + +The DMA fields are not used yet in the driver but are listed here for +completing the bindings. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + + flctl@e6a30000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "renesas,shmobile-flctl-sh7372"; + reg = <0xe6a30000 0x100>; + interrupts = <0x0d80>; + + nand-bus-width = <16>; + + dmas = <&dmac 1 /* data_tx */ + &dmac 2;> /* data_rx */ + dma-names = "data_tx", "data_rx"; + + system@0 { + label = "system"; + reg = <0x0 0x8000000>; + }; + + userdata@8000000 { + label = "userdata"; + reg = <0x8000000 0x10000000>; + }; + + cache@18000000 { + label = "cache"; + reg = <0x18000000 0x8000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt index e2c663b354d..e3ea32e7de3 100644 --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -3,9 +3,7 @@ Required properties: - compatible : "st,spear600-fsmc-nand" - reg : Address range of the mtd chip -- reg-names: Should contain the reg names "fsmc_regs" and "nand_data" -- st,ale-off : Chip specific offset to ALE -- st,cle-off : Chip specific offset to CLE +- reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd" Optional properties: - bank-width : Width (in bytes) of the device. If not present, the width @@ -19,10 +17,10 @@ Example: #address-cells = <1>; #size-cells = <1>; reg = <0xd1800000 0x1000 /* FSMC Register */ - 0xd2000000 0x4000>; /* NAND Base */ - reg-names = "fsmc_regs", "nand_data"; - st,ale-off = <0x20000>; - st,cle-off = <0x10000>; + 0xd2000000 0x0010 /* NAND Base DATA */ + 0xd2020000 0x0010 /* NAND Base ADDR */ + 0xd2010000 0x0010>; /* NAND Base CMD */ + reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd"; bank-width = <1>; nand-skip-bbtscan; diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/m25p80.txt new file mode 100644 index 00000000000..6d3d5760947 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/m25p80.txt @@ -0,0 +1,29 @@ +* MTD SPI driver for ST M25Pxx (and similar) serial flash chips + +Required properties: +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- compatible : Should be the manufacturer and the name of the chip. Bear in mind + the DT binding is not Linux-only, but in case of Linux, see the + "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of + supported chips. +- reg : Chip-Select number +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at + +Optional properties: +- m25p,fast-read : Use the "fast read" opcode to read data from the chip instead + of the usual "read" opcode. This opcode is not supported by + all chips and support for it can not be detected at runtime. + Refer to your chips' datasheet to check if this is supported + by your chip. + +Example: + + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,m25p80"; + reg = <0>; + spi-max-frequency = <40000000>; + m25p,fast-read; + }; diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt index 94de19b8f16..dab7847fc80 100644 --- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt +++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt @@ -23,6 +23,9 @@ file systems on embedded devices. unaligned accesses as implemented in the JFFS2 code via memcpy(). By defining "no-unaligned-direct-access", the flash will not be exposed directly to the MTD users (e.g. JFFS2) any more. + - linux,mtd-name: allow to specify the mtd name for retro capability with + physmap-flash drivers as boot loader pass the mtd partition via the old + device name physmap-flash. For JEDEC compatible devices, the following additional properties are defined: diff --git a/Documentation/devicetree/bindings/net/can/grcan.txt b/Documentation/devicetree/bindings/net/can/grcan.txt new file mode 100644 index 00000000000..34ef3498f88 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/grcan.txt @@ -0,0 +1,28 @@ +Aeroflex Gaisler GRCAN and GRHCAN CAN controllers. + +The GRCAN and CRHCAN CAN controllers are available in the GRLIB VHDL IP core +library. + +Note: These properties are built from the AMBA plug&play in a Leon SPARC system +(the ordinary environment for GRCAN and GRHCAN). There are no dts files for +sparc. + +Required properties: + +- name : Should be "GAISLER_GRCAN", "01_03d", "GAISLER_GRHCAN" or "01_034" + +- reg : Address and length of the register set for the device + +- freq : Frequency of the external oscillator clock in Hz (the frequency of + the amba bus in the ordinary case) + +- interrupts : Interrupt number for this device + +Optional properties: + +- systemid : If not present or if the value of the least significant 16 bits + of this 32-bit property is smaller than GRCAN_TXBUG_SAFE_GRLIB_VERSION + a bug workaround is activated. + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt new file mode 100644 index 00000000000..09055c2495f --- /dev/null +++ b/Documentation/devicetree/bindings/net/cdns-emac.txt @@ -0,0 +1,23 @@ +* Cadence EMAC Ethernet controller + +Required properties: +- compatible: Should be "cdns,[<chip>-]{emac}" + Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. + or the generic form: "cdns,emac". +- reg: Address and length of the register set for the device +- interrupts: Should contain macb interrupt +- phy-mode: String, operation mode of the PHY interface. + Supported values are: "mii", "rmii". + +Optional properties: +- local-mac-address: 6 bytes, mac address + +Examples: + + macb0: ethernet@fffc4000 { + compatible = "cdns,at91rm9200-emac"; + reg = <0xfffc4000 0x4000>; + interrupts = <21>; + phy-mode = "rmii"; + local-mac-address = [3a 0e 03 04 05 06]; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index dcaabe9fe86..6ddd0286a9b 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -9,21 +9,15 @@ Required properties: number - interrupt-parent : The parent interrupt controller - cpdma_channels : Specifies number of channels in CPDMA -- host_port_no : Specifies host port shift -- cpdma_reg_ofs : Specifies CPDMA submodule register offset -- cpdma_sram_ofs : Specifies CPDMA SRAM offset -- ale_reg_ofs : Specifies ALE submodule register offset - ale_entries : Specifies No of entries ALE can hold -- host_port_reg_ofs : Specifies host port register offset -- hw_stats_reg_ofs : Specifies hardware statistics register offset -- bd_ram_ofs : Specifies internal desciptor RAM offset - bd_ram_size : Specifies internal descriptor RAM size - rx_descs : Specifies number of Rx descriptors - mac_control : Specifies Default MAC control register content for the specific platform - slaves : Specifies number for slaves -- slave_reg_ofs : Specifies slave register offset -- sliver_reg_ofs : Specifies slave sliver register offset +- cpts_active_slave : Specifies the slave to use for time stamping +- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds +- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds - phy_id : Specifies slave phy id - mac-address : Specifies slave MAC address @@ -45,30 +39,22 @@ Examples: interrupts = <55 0x4>; interrupt-parent = <&intc>; cpdma_channels = <8>; - host_port_no = <0>; - cpdma_reg_ofs = <0x800>; - cpdma_sram_ofs = <0xa00>; - ale_reg_ofs = <0xd00>; ale_entries = <1024>; - host_port_reg_ofs = <0x108>; - hw_stats_reg_ofs = <0x900>; - bd_ram_ofs = <0x2000>; bd_ram_size = <0x2000>; no_bd_ram = <0>; rx_descs = <64>; mac_control = <0x20>; slaves = <2>; + cpts_active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; cpsw_emac0: slave@0 { - slave_reg_ofs = <0x208>; - sliver_reg_ofs = <0xd80>; - phy_id = "davinci_mdio.16:00"; + phy_id = <&davinci_mdio>, <0>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; cpsw_emac1: slave@1 { - slave_reg_ofs = <0x308>; - sliver_reg_ofs = <0xdc0>; - phy_id = "davinci_mdio.16:01"; + phy_id = <&davinci_mdio>, <1>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; @@ -79,30 +65,22 @@ Examples: compatible = "ti,cpsw"; ti,hwmods = "cpgmac0"; cpdma_channels = <8>; - host_port_no = <0>; - cpdma_reg_ofs = <0x800>; - cpdma_sram_ofs = <0xa00>; - ale_reg_ofs = <0xd00>; ale_entries = <1024>; - host_port_reg_ofs = <0x108>; - hw_stats_reg_ofs = <0x900>; - bd_ram_ofs = <0x2000>; bd_ram_size = <0x2000>; no_bd_ram = <0>; rx_descs = <64>; mac_control = <0x20>; slaves = <2>; + cpts_active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; cpsw_emac0: slave@0 { - slave_reg_ofs = <0x208>; - sliver_reg_ofs = <0xd80>; - phy_id = "davinci_mdio.16:00"; + phy_id = <&davinci_mdio>, <0>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; cpsw_emac1: slave@1 { - slave_reg_ofs = <0x308>; - sliver_reg_ofs = <0xdc0>; - phy_id = "davinci_mdio.16:01"; + phy_id = <&davinci_mdio>, <1>; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt new file mode 100644 index 00000000000..859a6fa7569 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -0,0 +1,23 @@ +* Marvell Armada 370 / Armada XP Ethernet Controller (NETA) + +Required properties: +- compatible: should be "marvell,armada-370-neta". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device +- phy: A phandle to a phy node defining the PHY address (as the reg + property, a single integer). +- phy-mode: The interface between the SoC and the PHY (a string that + of_get_phy_mode() can understand) +- clocks: a pointer to the reference clock for this device. + +Example: + +ethernet@d0070000 { + compatible = "marvell,armada-370-neta"; + reg = <0xd0070000 0x2500>; + interrupts = <8>; + clocks = <&gate_clk 4>; + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt new file mode 100644 index 00000000000..34e7aafa321 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt @@ -0,0 +1,35 @@ +* Marvell MDIO Ethernet Controller interface + +The Ethernet controllers of the Marvel Kirkwood, Dove, Orion5x, +MV78xx0, Armada 370 and Armada XP have an identical unit that provides +an interface with the MDIO bus. This driver handles this MDIO +interface. + +Required properties: +- compatible: "marvell,orion-mdio" +- reg: address and length of the SMI register + +The child nodes of the MDIO driver are the individual PHY devices +connected to this MDIO bus. They must have a "reg" property given the +PHY address on the MDIO bus. + +Example at the SoC level: + +mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,orion-mdio"; + reg = <0xd0072004 0x4>; +}; + +And at the board level: + +mdio { + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +} diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt index bc954952901..c79bab02536 100644 --- a/Documentation/devicetree/bindings/net/mdio-gpio.txt +++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt @@ -8,9 +8,16 @@ gpios property as described in section VIII.1 in the following order: MDC, MDIO. +Note: Each gpio-mdio bus should have an alias correctly numbered in "aliases" +node. + Example: -mdio { +aliases { + mdio-gpio0 = <&mdio0>; +}; + +mdio0: mdio { compatible = "virtual,mdio-gpio"; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt new file mode 100644 index 00000000000..3a268127b05 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -0,0 +1,141 @@ +* Atmel AT91 Pinmux Controller + +The AT91 Pinmux Controler, enables the IC +to share one PAD to several functional blocks. The sharing is done by +multiplexing the PAD input/output signals. For each PAD there are up to +8 muxing options (called periph modes). Since different modules require +different PAD settings (like pull up, keeper, etc) the contoller controls +also the PAD settings parameters. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Atmel AT91 pin configuration node is a node of a group of pins which can be +used for a specific device or function. This node represents both mux and config +of the pins in that group. The 'pins' selects the function mode(also named pin +mode) this pin can work on and the 'config' configures various pad settings +such as pull-up, multi drive, etc. + +Required properties for iomux controller: +- compatible: "atmel,at91rm9200-pinctrl" +- atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be + configured in this periph mode. All the periph and bank need to be describe. + +How to create such array: + +Each column will represent the possible peripheral of the pinctrl +Each line will represent a pio bank + +Take an example on the 9260 +Peripheral: 2 ( A and B) +Bank: 3 (A, B and C) +=> + + /* A B */ + 0xffffffff 0xffc00c3b /* pioA */ + 0xffffffff 0x7fff3ccf /* pioB */ + 0xffffffff 0x007fffff /* pioC */ + +For each peripheral/bank we will descibe in a u32 if a pin can can be +configured in it by putting 1 to the pin bit (1 << pin) + +Let's take the pioA on peripheral B +From the datasheet Table 10-2. +Peripheral B +PA0 MCDB0 +PA1 MCCDB +PA2 +PA3 MCDB3 +PA4 MCDB2 +PA5 MCDB1 +PA6 +PA7 +PA8 +PA9 +PA10 ETX2 +PA11 ETX3 +PA12 +PA13 +PA14 +PA15 +PA16 +PA17 +PA18 +PA19 +PA20 +PA21 +PA22 ETXER +PA23 ETX2 +PA24 ETX3 +PA25 ERX2 +PA26 ERX3 +PA27 ERXCK +PA28 ECRS +PA29 ECOL +PA30 RXD4 +PA31 TXD4 + +=> 0xffc00c3b + +Required properties for pin configuration node: +- atmel,pins: 4 integers array, represents a group of pins mux and config + setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>. + The PERIPH 0 means gpio. + +Bits used for CONFIG: +PULL_UP (1 << 0): indicate this pin need a pull up. +MULTIDRIVE (1 << 1): indicate this pin need to be configured as multidrive. +DEGLITCH (1 << 2): indicate this pin need deglitch. +PULL_DOWN (1 << 3): indicate this pin need a pull down. +DIS_SCHMIT (1 << 4): indicate this pin need to disable schmit trigger. +DEBOUNCE (1 << 16): indicate this pin need debounce. +DEBOUNCE_VAL (0x3fff << 17): debounce val. + +NOTE: +Some requirements for using atmel,at91rm9200-pinctrl binding: +1. We have pin function node defined under at91 controller node to represent + what pinmux functions this SoC supports. +2. The driver can use the function node's name and pin configuration node's + name describe the pin function and group hierarchy. + For example, Linux at91 pinctrl driver takes the function node's name + as the function name and pin configuration node's name as group name to + create the map table. +3. Each pin configuration node should have a phandle, devices can set pins + configurations by referring to the phandle of that pin configuration node. +4. The gpio controller must be describe in the pinctrl simple-bus. + +Examples: + +pinctrl@fffff400 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; + reg = <0xfffff400 0x600>; + + atmel,mux-mask = < + /* A B */ + 0xffffffff 0xffc00c3b /* pioA */ + 0xffffffff 0x7fff3ccf /* pioB */ + 0xffffffff 0x007fffff /* pioC */ + >; + + /* shared pinctrl settings */ + dbgu { + pinctrl_dbgu: dbgu-0 { + atmel,pins = + <1 14 0x1 0x0 /* PB14 periph A */ + 1 15 0x1 0x1>; /* PB15 periph with pullup */ + }; + }; +}; + +dbgu: serial@fffff200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffff200 0x200>; + interrupts = <1 4 7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dbgu>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt index 361bccb7ec8..95daf6335c3 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt @@ -7,8 +7,10 @@ Required properties: - compatible: "marvell,88f6180-pinctrl", "marvell,88f6190-pinctrl", "marvell,88f6192-pinctrl", "marvell,88f6281-pinctrl", "marvell,88f6282-pinctrl" + "marvell,98dx4122-pinctrl" This driver supports all kirkwood variants, i.e. 88f6180, 88f619x, and 88f628x. +It also support the 88f6281-based variant in the 98dx412x Bobcat SoCs. Available mpp pins/groups and functions: Note: brackets (x) are not part of the mpp name for marvell,function and given @@ -277,3 +279,40 @@ mpp46 46 gpio, ts(mp10), tdm(fs), lcd(hsync) mpp47 47 gpio, ts(mp11), tdm(drx), lcd(vsync) mpp48 48 gpio, ts(mp12), tdm(dtx), lcd(d16) mpp49 49 gpo, tdm(rx0ql), pex(clkreq), lcd(d17) + +* Marvell Bobcat 98dx4122 + +name pins functions +================================================================================ +mpp0 0 gpio, nand(io2), spi(cs) +mpp1 1 gpo, nand(io3), spi(mosi) +mpp2 2 gpo, nand(io4), spi(sck) +mpp3 3 gpo, nand(io5), spi(miso) +mpp4 4 gpio, nand(io6), uart0(rxd) +mpp5 5 gpo, nand(io7), uart0(txd) +mpp6 6 sysrst(out), spi(mosi) +mpp7 7 gpo, pex(rsto), spi(cs) +mpp8 8 gpio, twsi0(sda), uart0(rts), uart1(rts) +mpp9 9 gpio, twsi(sck), uart0(cts), uart1(cts) +mpp10 10 gpo, spi(sck), uart0(txd) +mpp11 11 gpio, spi(miso), uart0(rxd) +mpp13 13 gpio, uart1(txd) +mpp14 14 gpio, uart1(rxd) +mpp15 15 gpio, uart0(rts) +mpp16 16 gpio, uart0(cts) +mpp18 18 gpo, nand(io0) +mpp19 19 gpo, nand(io1) +mpp34 34 gpio +mpp35 35 gpio +mpp36 36 gpio +mpp37 37 gpio +mpp38 38 gpio +mpp39 39 gpio +mpp40 40 gpio +mpp41 41 gpio +mpp42 42 gpio +mpp43 43 gpio +mpp44 44 gpio +mpp45 45 gpio +mpp49 49 gpio + diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt index c8e578263ce..683fde93c4f 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt @@ -93,7 +93,7 @@ Valid values for pin and group names are: With some exceptions, these support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode, nvidia,pull-down-strength, - nvidia,pull-up-strength, nvidia,slew_rate-rising, nvidia,slew_rate-falling. + nvidia,pull-up-strength, nvidia,slew-rate-rising, nvidia,slew-rate-falling. drive_ao1, drive_ao2, drive_at1, drive_at2, drive_cdev1, drive_cdev2, drive_csus, drive_dap1, drive_dap2, drive_dap3, drive_dap4, drive_dbg, diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt index c275b70349c..6f426ed7009 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt @@ -83,7 +83,7 @@ Valid values for pin and group names are: drive groups: These all support nvidia,pull-down-strength, nvidia,pull-up-strength, - nvidia,slew_rate-rising, nvidia,slew_rate-falling. Most but not all + nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode. ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, cec, crt, csus, dap1, diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index 03dee50532f..e97a27856b2 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -8,13 +8,20 @@ on-chip controllers onto these pads. Required Properties: - compatible: should be one of the following. - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller. + - "samsung,pinctrl-exynos4x12": for Exynos4x12 compatible pin-controller. - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller. - reg: Base address of the pin controller hardware module and length of the address space it occupies. -- interrupts: interrupt specifier for the controller. The format and value of - the interrupt specifier depends on the interrupt parent for the controller. +- Pin banks as child nodes: Pin banks of the controller are represented by child + nodes of the controller node. Bank name is taken from name of the node. Each + bank node must contain following properties: + + - gpio-controller: identifies the node as a gpio controller and pin bank. + - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO + binding is used, the amount of cells must be specified as 2. See generic + GPIO binding documentation for description of particular cells. - Pin mux/config groups as child nodes: The pin mux (selecting pin function mode) and pin config (pull up/down, driver strength) settings are represented @@ -72,16 +79,24 @@ used as system wakeup events. A. External GPIO Interrupts: For supporting external gpio interrupts, the following properties should be specified in the pin-controller device node. -- interrupt-controller: identifies the controller node as interrupt-parent. -- #interrupt-cells: the value of this property should be 2. - - First Cell: represents the external gpio interrupt number local to the - external gpio interrupt space of the controller. - - Second Cell: flags to identify the type of the interrupt - - 1 = rising edge triggered - - 2 = falling edge triggered - - 3 = rising and falling edge triggered - - 4 = high level triggered - - 8 = low level triggered + - interrupt-parent: phandle of the interrupt parent to which the external + GPIO interrupts are forwarded to. + - interrupts: interrupt specifier for the controller. The format and value of + the interrupt specifier depends on the interrupt parent for the controller. + + In addition, following properties must be present in node of every bank + of pins supporting GPIO interrupts: + + - interrupt-controller: identifies the controller node as interrupt-parent. + - #interrupt-cells: the value of this property should be 2. + - First Cell: represents the external gpio interrupt number local to the + external gpio interrupt space of the controller. + - Second Cell: flags to identify the type of the interrupt + - 1 = rising edge triggered + - 2 = falling edge triggered + - 3 = rising and falling edge triggered + - 4 = high level triggered + - 8 = low level triggered B. External Wakeup Interrupts: For supporting external wakeup interrupts, a child node representing the external wakeup interrupt controller should be @@ -94,6 +109,11 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a found on Samsung Exynos4210 SoC. - interrupt-parent: phandle of the interrupt parent to which the external wakeup interrupts are forwarded to. + - interrupts: interrupt used by multiplexed wakeup interrupts. + + In addition, following properties must be present in node of every bank + of pins supporting wake-up interrupts: + - interrupt-controller: identifies the node as interrupt-parent. - #interrupt-cells: the value of this property should be 2 - First Cell: represents the external wakeup interrupt number local to @@ -105,11 +125,63 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a - 4 = high level triggered - 8 = low level triggered + Node of every bank of pins supporting direct wake-up interrupts (without + multiplexing) must contain following properties: + + - interrupt-parent: phandle of the interrupt parent to which the external + wakeup interrupts are forwarded to. + - interrupts: interrupts of the interrupt parent which are used for external + wakeup interrupts from pins of the bank, must contain interrupts for all + pins of the bank. + Aliases: All the pin controller nodes should be represented in the aliases node using the following format 'pinctrl{n}' where n is a unique number for the alias. +Example: A pin-controller node with pin banks: + + pinctrl_0: pinctrl@11400000 { + compatible = "samsung,pinctrl-exynos4210"; + reg = <0x11400000 0x1000>; + interrupts = <0 47 0>; + + /* ... */ + + /* Pin bank without external interrupts */ + gpy0: gpy0 { + gpio-controller; + #gpio-cells = <2>; + }; + + /* ... */ + + /* Pin bank with external GPIO or muxed wake-up interrupts */ + gpj0: gpj0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + /* ... */ + + /* Pin bank with external direct wake-up interrupts */ + gpx0: gpx0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + interrupt-parent = <&gic>; + interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>, + <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>; + #interrupt-cells = <2>; + }; + + /* ... */ + }; + Example 1: A pin-controller node with pin groups. pinctrl_0: pinctrl@11400000 { @@ -117,6 +189,8 @@ Example 1: A pin-controller node with pin groups. reg = <0x11400000 0x1000>; interrupts = <0 47 0>; + /* ... */ + uart0_data: uart0-data { samsung,pins = "gpa0-0", "gpa0-1"; samsung,pin-function = <2>; @@ -158,20 +232,14 @@ Example 2: A pin-controller node with external wakeup interrupt controller node. pinctrl_1: pinctrl@11000000 { compatible = "samsung,pinctrl-exynos4210"; reg = <0x11000000 0x1000>; - interrupts = <0 46 0>; - interrupt-controller; - #interrupt-cells = <2>; + interrupts = <0 46 0> - wakup_eint: wakeup-interrupt-controller { + /* ... */ + + wakeup-interrupt-controller { compatible = "samsung,exynos4210-wakeup-eint"; interrupt-parent = <&gic>; - interrupt-controller; - #interrupt-cells = <2>; - interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>, - <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>, - <0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>, - <0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>, - <0 32 0>; + interrupts = <0 32 0>; }; }; @@ -190,7 +258,8 @@ Example 4: Set up the default pin state for uart controller. static int s3c24xx_serial_probe(struct platform_device *pdev) { struct pinctrl *pinctrl; - ... - ... + + /* ... */ + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); } diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt b/Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt new file mode 100644 index 00000000000..0ba1bcc7f33 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/ab8500/btemp.txt @@ -0,0 +1,16 @@ +=== AB8500 Battery Temperature Monitor Driver === + +The properties below describes the node for btemp driver. + +Required Properties: +- compatible = Shall be: "stericsson,ab8500-btemp" +- battery = Shall be battery specific information + + Example: + ab8500_btemp { + compatible = "stericsson,ab8500-btemp"; + battery = <&ab8500_battery>; + }; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power_supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt b/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt new file mode 100644 index 00000000000..ef532837112 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/ab8500/chargalg.txt @@ -0,0 +1,16 @@ +=== AB8500 Charging Algorithm Driver === + +The properties below describes the node for chargalg driver. + +Required Properties: +- compatible = Shall be: "stericsson,ab8500-chargalg" +- battery = Shall be battery specific information + +Example: +ab8500_chargalg { + compatible = "stericsson,ab8500-chargalg"; + battery = <&ab8500_battery>; +}; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power_supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/charger.txt b/Documentation/devicetree/bindings/power_supply/ab8500/charger.txt new file mode 100644 index 00000000000..6bdbb08ea9e --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/ab8500/charger.txt @@ -0,0 +1,25 @@ +=== AB8500 Charger Driver === + +Required Properties: +- compatible = Shall be "stericsson,ab8500-charger" +- battery = Shall be battery specific information + Example: + ab8500_charger { + compatible = "stericsson,ab8500-charger"; + battery = <&ab8500_battery>; + }; + +- vddadc-supply: Supply for USB and Main charger + Example: + ab8500-charger { + vddadc-supply = <&ab8500_ldo_tvout_reg>; + } +- autopower_cfg: + Boolean value depicting the presence of 'automatic poweron after powerloss' + Example: + ab8500-charger { + autopower_cfg; + }; + +For information on battery specific node, Ref: +Documentation/devicetree/bindings/power_supply/ab8500/fg.txt diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt b/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt new file mode 100644 index 00000000000..ccafcb9112f --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt @@ -0,0 +1,58 @@ +=== AB8500 Fuel Gauge Driver === + +AB8500 is a mixed signal multimedia and power management +device comprising: power and energy-management-module, +wall-charger, usb-charger, audio codec, general purpose adc, +tvout, clock management and sim card interface. + +Fuelgauge support is part of energy-management-modules, other +components of this module are: +main-charger, usb-combo-charger and battery-temperature-monitoring. + +The properties below describes the node for fuelgauge driver. + +Required Properties: +- compatible = This shall be: "stericsson,ab8500-fg" +- battery = Shall be battery specific information + Example: + ab8500_fg { + compatible = "stericsson,ab8500-fg"; + battery = <&ab8500_battery>; + }; + +dependent node: + ab8500_battery: ab8500_battery { + }; + This node will provide information on 'thermistor interface' and + 'battery technology type' used. + +Properties of this node are: +thermistor-on-batctrl: + A boolean value indicating thermistor interface to battery + + Note: + 'btemp' and 'batctrl' are the pins interfaced for battery temperature + measurement, 'btemp' signal is used when NTC(negative temperature + coefficient) resister is interfaced external to battery whereas + 'batctrl' pin is used when NTC resister is internal to battery. + + Example: + ab8500_battery: ab8500_battery { + thermistor-on-batctrl; + }; + indicates: NTC resister is internal to battery, 'batctrl' is used + for thermal measurement. + + The absence of property 'thermal-on-batctrl' indicates + NTC resister is external to battery and 'btemp' signal is used + for thermal measurement. + +battery-type: + This shall be the battery manufacturing technology type, + allowed types are: + "UNKNOWN" "NiMH" "LION" "LIPO" "LiFe" "NiCd" "LiMn" + Example: + ab8500_battery: ab8500_battery { + stericsson,battery-type = "LIPO"; + } + diff --git a/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt new file mode 100644 index 00000000000..4ad29b9ac2a --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/raideng.txt @@ -0,0 +1,81 @@ +* Freescale 85xx RAID Engine nodes + +RAID Engine nodes are defined to describe on-chip RAID accelerators. Each RAID +Engine should have a separate node. + +Supported chips: +P5020, P5040 + +Required properties: + +- compatible: Should contain "fsl,raideng-v1.0" as the value + This identifies RAID Engine block. 1 in 1.0 represents + major number whereas 0 represents minor number. The + version matches the hardware IP version. +- reg: offset and length of the register set for the device +- ranges: standard ranges property specifying the translation + between child address space and parent address space + +Example: + /* P5020 */ + raideng: raideng@320000 { + compatible = "fsl,raideng-v1.0"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x320000 0x10000>; + ranges = <0 0x320000 0x10000>; + }; + + +There must be a sub-node for each job queue present in RAID Engine +This node must be a sub-node of the main RAID Engine node + +- compatible: Should contain "fsl,raideng-v1.0-job-queue" as the value + This identifies the job queue interface +- reg: offset and length of the register set for job queue +- ranges: standard ranges property specifying the translation + between child address space and parent address space + +Example: + /* P5020 */ + raideng_jq0@1000 { + compatible = "fsl,raideng-v1.0-job-queue"; + reg = <0x1000 0x1000>; + ranges = <0x0 0x1000 0x1000>; + }; + + +There must be a sub-node for each job ring present in RAID Engine +This node must be a sub-node of job queue node + +- compatible: Must contain "fsl,raideng-v1.0-job-ring" as the value + This identifies job ring. Should contain either + "fsl,raideng-v1.0-hp-ring" or "fsl,raideng-v1.0-lp-ring" + depending upon whether ring has high or low priority +- reg: offset and length of the register set for job ring +- interrupts: interrupt mapping for job ring IRQ + +Optional property: + +- fsl,liodn: Specifies the LIODN to be used for Job Ring. This + property is normally set by firmware. Value + is of 12-bits which is the LIODN number for this JR. + This property is used by the IOMMU (PAMU) to distinquish + transactions from this JR and than be able to do address + translation & protection accordingly. + +Example: + /* P5020 */ + raideng_jq0@1000 { + compatible = "fsl,raideng-v1.0-job-queue"; + reg = <0x1000 0x1000>; + ranges = <0x0 0x1000 0x1000>; + + raideng_jr0: jr@0 { + compatible = "fsl,raideng-v1.0-job-ring", "fsl,raideng-v1.0-hp-ring"; + reg = <0x0 0x400>; + interrupts = <139 2 0 0>; + interrupt-parent = <&mpic>; + fsl,liodn = <0x41>; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt new file mode 100644 index 00000000000..131e8c11d26 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -0,0 +1,23 @@ +TI SOC ECAP based APWM controller + +Required properties: +- compatible: Must be "ti,am33xx-ecap" +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the ECAP: + "ecap<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ecap0: ecap@0 { + compatible = "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48300100 0x80>; + ti,hwmods = "ecap0"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt new file mode 100644 index 00000000000..4fc7079d822 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt @@ -0,0 +1,23 @@ +TI SOC EHRPWM based PWM controller + +Required properties: +- compatible : Must be "ti,am33xx-ehrpwm" +- #pwm-cells: Should be 3. Number of cells being used to specify PWM property. + First cell specifies the per-chip index of the PWM to use, the second + cell is the period in nanoseconds and bit 0 in the third cell is used to + encode the polarity of PWM output. Set bit 0 of the third in PWM specifier + to 1 for inverse polarity & set to 0 for normal polarity. +- reg: physical base address and size of the registers map. + +Optional properties: +- ti,hwmods: Name of the hwmod associated to the EHRPWM: + "ehrpwm<x>", <x> being the 0-based instance number from the HW spec + +Example: + +ehrpwm0: ehrpwm@0 { + compatible = "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48300200 0x100>; + ti,hwmods = "ehrpwm0"; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt new file mode 100644 index 00000000000..f7eae77f835 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt @@ -0,0 +1,31 @@ +TI SOC based PWM Subsystem + +Required properties: +- compatible: Must be "ti,am33xx-pwmss"; +- reg: physical base address and size of the registers map. +- address-cells: Specify the number of u32 entries needed in child nodes. + Should set to 1. +- size-cells: specify number of u32 entries needed to specify child nodes size + in reg property. Should set to 1. +- ranges: describes the address mapping of a memory-mapped bus. Should set to + physical address map of child's base address, physical address within + parent's address space and length of the address map. For am33xx, + 3 set of child register maps present, ECAP register space, EQEP + register space, EHRPWM register space. + +Also child nodes should also populated under PWMSS DT node. + +Example: +pwmss0: pwmss@48300000 { + compatible = "ti,am33xx-pwmss"; + reg = <0x48300000 0x10>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + ranges = <0x48300100 0x48300100 0x80 /* ECAP */ + 0x48300180 0x48300180 0x80 /* EQEP */ + 0x48300200 0x48300200 0x80>; /* EHRPWM */ + + /* child nodes go here */ +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt index 73ec962bfe8..06e67247859 100644 --- a/Documentation/devicetree/bindings/pwm/pwm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm.txt @@ -37,10 +37,21 @@ device: pwm-names = "backlight"; }; +Note that in the example above, specifying the "pwm-names" is redundant +because the name "backlight" would be used as fallback anyway. + pwm-specifier typically encodes the chip-relative PWM number and the PWM -period in nanoseconds. Note that in the example above, specifying the -"pwm-names" is redundant because the name "backlight" would be used as -fallback anyway. +period in nanoseconds. + +Optionally, the pwm-specifier can encode a number of flags in a third cell: +- bit 0: PWM signal polarity (0: normal polarity, 1: inverse polarity) + +Example with optional PWM specifier for inverse polarity + + bl: backlight { + pwms = <&pwm 0 5000000 1>; + pwm-names = "backlight"; + }; 2) PWM controller nodes ----------------------- diff --git a/Documentation/devicetree/bindings/pwm/spear-pwm.txt b/Documentation/devicetree/bindings/pwm/spear-pwm.txt new file mode 100644 index 00000000000..3ac779d8338 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/spear-pwm.txt @@ -0,0 +1,18 @@ +== ST SPEAr SoC PWM controller == + +Required properties: +- compatible: should be one of: + - "st,spear320-pwm" + - "st,spear1340-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: number of cells used to specify PWM which is fixed to 2 on + SPEAr. The first cell specifies the per-chip index of the PWM to use and + the second cell is the period in nanoseconds. + +Example: + + pwm: pwm@a8000000 { + compatible ="st,spear320-pwm"; + reg = <0xa8000000 0x1000>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt new file mode 100644 index 00000000000..2943ee5fce0 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers + +Supported PWMs: +On TWL4030 series: PWM1 and PWM2 +On TWL6030 series: PWM0 and PWM1 + +Required properties: +- compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm" +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + +Example: + +twl_pwm: pwm { + compatible = "ti,twl6030-pwm"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt new file mode 100644 index 00000000000..cb64f3acc10 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt @@ -0,0 +1,17 @@ +Texas Instruments TWL series PWM drivers connected to LED terminals + +Supported PWMs: +On TWL4030 series: PWMA and PWMB (connected to LEDA and LEDB terminals) +On TWL6030 series: LED PWM (mainly used as charging indicator LED) + +Required properties: +- compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled" +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + +Example: + +twl_pwmled: pwmled { + compatible = "ti,twl6030-pwmled"; + #pwm-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt new file mode 100644 index 00000000000..bcc63678a9a --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt @@ -0,0 +1,17 @@ +VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller + +Required properties: +- compatible: should be "via,vt8500-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. +- clocks: phandle to the PWM source clock + +Example: + +pwm1: pwm@d8220000 { + #pwm-cells = <2>; + compatible = "via,vt8500-pwm"; + reg = <0xd8220000 0x1000>; + clocks = <&clkpwm>; +}; diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt new file mode 100644 index 00000000000..63c659800c0 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt @@ -0,0 +1,37 @@ +GPIO controlled regulators + +Required properties: +- compatible : Must be "regulator-gpio". +- states : Selection of available voltages and GPIO configs. + if there are no states, then use a fixed regulator + +Optional properties: +- enable-gpio : GPIO to use to enable/disable the regulator. +- gpios : GPIO group used to control voltage. +- startup-delay-us : Startup time in microseconds. +- enable-active-high : Polarity of GPIO is active high (default is low). + +Any property defined as part of the core regulator binding defined in +regulator.txt can also be used. + +Example: + + mmciv: gpio-regulator { + compatible = "regulator-gpio"; + + regulator-name = "mmci-gpio-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2600000>; + regulator-boot-on; + + enable-gpio = <&gpio0 23 0x4>; + gpios = <&gpio0 24 0x4 + &gpio0 25 0x4>; + states = <1800000 0x3 + 2200000 0x2 + 2600000 0x1 + 2900000 0x0>; + + startup-delay-us = <100000>; + enable-active-high; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8925-regulator.txt b/Documentation/devicetree/bindings/regulator/max8925-regulator.txt new file mode 100644 index 00000000000..0057695aae8 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8925-regulator.txt @@ -0,0 +1,40 @@ +Max8925 Voltage regulators + +Required nodes: +-nodes: + - SDV1 for SDV SDV1 + - SDV2 for SDV SDV2 + - SDV3 for SDV SDV3 + - LDO1 for LDO LDO1 + - LDO2 for LDO LDO2 + - LDO3 for LDO LDO3 + - LDO4 for LDO LDO4 + - LDO5 for LDO LDO5 + - LDO6 for LDO LDO6 + - LDO7 for LDO LDO7 + - LDO8 for LDO LDO8 + - LDO9 for LDO LDO9 + - LDO10 for LDO LDO10 + - LDO11 for LDO LDO11 + - LDO12 for LDO LDO12 + - LDO13 for LDO LDO13 + - LDO14 for LDO LDO14 + - LDO15 for LDO LDO15 + - LDO16 for LDO LDO16 + - LDO17 for LDO LDO17 + - LDO18 for LDO LDO18 + - LDO19 for LDO LDO19 + - LDO20 for LDO LDO20 + +Optional properties: +- Any optional property defined in bindings/regulator/regulator.txt + +Example: + + SDV1 { + regulator-min-microvolt = <637500>; + regulator-max-microvolt = <1425000>; + regulator-boot-on; + regulator-always-on; + }; + diff --git a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt new file mode 100644 index 00000000000..9fd69a18b0b --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt @@ -0,0 +1,146 @@ +* Maxim MAX8997 Voltage and Current Regulator + +The Maxim MAX8997 is a multi-function device which includes volatage and +current regulators, rtc, charger controller and other sub-blocks. It is +interfaced to the host controller using a i2c interface. Each sub-block is +addressed by the host system using different i2c slave address. This document +describes the bindings for 'pmic' sub-block of max8997. + +Required properties: +- compatible: Should be "maxim,max8997-pmic". +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +- max8997,pmic-buck1-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck1 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- max8997,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck2 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- max8997,pmic-buck5-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck5 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +[1] If none of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional + property is specified, the 'max8997,pmic-buck[1/2/5]-dvs-voltage' + property should specify atleast one voltage level (which would be a + safe operating voltage). + + If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional + property is specified, then all the eigth voltage values for the + 'max8997,pmic-buck[1/2/5]-dvs-voltage' should be specified. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from max8997 are delivered to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for 'irq1' interrupt. + - Second interrupt specifier is for 'alert' interrupt. +- max8997,pmic-buck1-uses-gpio-dvs: 'buck1' can be controlled by gpio dvs. +- max8997,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. +- max8997,pmic-buck5-uses-gpio-dvs: 'buck5' can be controlled by gpio dvs. + +Additional properties required if either of the optional properties are used: +- max8997,pmic-ignore-gpiodvs-side-effect: When GPIO-DVS mode is used for + multiple bucks, changing the voltage value of one of the bucks may affect + that of another buck, which is the side effect of the change (set_voltage). + Use this property to ignore such side effects and change the voltage. + +- max8997,pmic-buck125-default-dvs-idx: Default voltage setting selected from + the possible 8 options selectable by the dvs gpios. The value of this + property should be between 0 and 7. If not specified or if out of range, the + default value of this property is set to 0. + +- max8997,pmic-buck125-dvs-gpios: GPIO specifiers for three host gpio's used + for dvs. The format of the gpio specifier depends in the gpio controller. + +Regulators: The regulators of max8997 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + standard regulator bindings here + }; + +The following are the names of the regulators that the max8997 pmic block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of max8997. + + - LDOn + - valid values for n are 1 to 18 and 21 + - Example: LDO0, LD01, LDO2, LDO21 + - BUCKn + - valid values for n are 1 to 7. + - Example: BUCK1, BUCK2, BUCK3, BUCK7 + + - ENVICHG: Battery Charging Current Monitor Output. This is a fixed + voltage type regulator + + - ESAFEOUT1: (ldo19) + - ESAFEOUT2: (ld020) + + - CHARGER_CV: main battery charger voltage control + - CHARGER: main battery charger current control + - CHARGER_TOPOFF: end of charge current threshold level + +The bindings inside the regulator nodes use the standard regulator bindings +which are documented elsewhere. + +Example: + + max8997_pmic@66 { + compatible = "maxim,max8997-pmic"; + interrupt-parent = <&wakeup_eint>; + reg = <0x66>; + interrupts = <4 0>, <3 0>; + + max8997,pmic-buck1-uses-gpio-dvs; + max8997,pmic-buck2-uses-gpio-dvs; + max8997,pmic-buck5-uses-gpio-dvs; + + max8997,pmic-ignore-gpiodvs-side-effect; + max8997,pmic-buck125-default-dvs-idx = <0>; + + max8997,pmic-buck125-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */ + <&gpx0 1 1 0 0>, /* SET2 */ + <&gpx0 2 1 0 0>; /* SET3 */ + + max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + max8997,pmic-buck2-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1000000>, <1000000>, + <1000000>, <1000000>; + + max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_ARM_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt index d316fb895da..4f05d208c95 100644 --- a/Documentation/devicetree/bindings/regulator/tps65217.txt +++ b/Documentation/devicetree/bindings/regulator/tps65217.txt @@ -11,6 +11,9 @@ Required properties: using the standard binding for regulators found at Documentation/devicetree/bindings/regulator/regulator.txt. +Optional properties: +- ti,pmic-shutdown-controller: Telling the PMIC to shutdown on PWR_EN toggle. + The valid names for regulators are: tps65217: dcdc1, dcdc2, dcdc3, ldo1, ldo2, ldo3 and ldo4 @@ -20,6 +23,7 @@ Example: tps: tps@24 { compatible = "ti,tps65217"; + ti,pmic-shutdown-controller; regulators { dcdc1_reg: dcdc1 { diff --git a/Documentation/devicetree/bindings/regulator/vexpress.txt b/Documentation/devicetree/bindings/regulator/vexpress.txt new file mode 100644 index 00000000000..d775f72487a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/vexpress.txt @@ -0,0 +1,32 @@ +Versatile Express voltage regulators +------------------------------------ + +Requires node properties: +- "compatible" value: "arm,vexpress-volt" +- "arm,vexpress-sysreg,func" when controlled via vexpress-sysreg + (see Documentation/devicetree/bindings/arm/vexpress-sysreg.txt + for more details) + +Required regulator properties: +- "regulator-name" +- "regulator-always-on" + +Optional regulator properties: +- "regulator-min-microvolt" +- "regulator-max-microvolt" + +See Documentation/devicetree/bindings/regulator/regulator.txt +for more details about the regulator properties. + +When no "regulator-[min|max]-microvolt" properties are defined, +the device is treated as fixed (or rather "read-only") regulator. + +Example: + volt@0 { + compatible = "arm,vexpress-volt"; + arm,vexpress-sysreg,func = <2 0>; + regulator-name = "Cores"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + }; diff --git a/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt b/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt new file mode 100644 index 00000000000..c9d80d7da14 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt @@ -0,0 +1,17 @@ +* i.MX25 Real Time Clock controller + +This binding supports the following chips: i.MX25, i.MX53 + +Required properties: +- compatible: should be: "fsl,imx25-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: rtc alarm interrupt + +Example: + +rtc@80056000 { + compatible = "fsl,imx53-rtc", "fsl,imx25-rtc"; + reg = <0x80056000 2000>; + interrupts = <29>; +}; diff --git a/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt b/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt new file mode 100644 index 00000000000..93f45e9dce7 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/nvidia,tegra20-rtc.txt @@ -0,0 +1,19 @@ +NVIDIA Tegra20 real-time clock + +The Tegra RTC maintains seconds and milliseconds counters, and five alarm +registers. The alarms and other interrupts may wake the system from low-power +state. + +Required properties: + +- compatible : should be "nvidia,tegra20-rtc". +- reg : Specifies base physical address and size of the registers. +- interrupts : A single interrupt specifier. + +Example: + +timer { + compatible = "nvidia,tegra20-rtc"; + reg = <0x7000e000 0x100>; + interrupts = <0 2 0x04>; +}; diff --git a/Documentation/devicetree/bindings/rtc/orion-rtc.txt b/Documentation/devicetree/bindings/rtc/orion-rtc.txt new file mode 100644 index 00000000000..3bf63ffa516 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/orion-rtc.txt @@ -0,0 +1,18 @@ +* Mvebu Real Time Clock + +RTC controller for the Kirkwood, the Dove, the Armada 370 and the +Armada XP SoCs + +Required properties: +- compatible : Should be "marvell,orion-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: IRQ line for the RTC. + +Example: + +rtc@10300 { + compatible = "marvell,orion-rtc"; + reg = <0xd0010300 0x20>; + interrupts = <50>; +}; diff --git a/Documentation/devicetree/bindings/rtc/rtc-omap.txt b/Documentation/devicetree/bindings/rtc/rtc-omap.txt new file mode 100644 index 00000000000..b47aa415c82 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-omap.txt @@ -0,0 +1,17 @@ +TI Real Time Clock + +Required properties: +- compatible: "ti,da830-rtc" +- reg: Address range of rtc register set +- interrupts: rtc timer, alarm interrupts in order +- interrupt-parent: phandle for the interrupt controller + +Example: + +rtc@1c23000 { + compatible = "ti,da830-rtc"; + reg = <0x23000 0x1000>; + interrupts = <19 + 19>; + interrupt-parent = <&intc>; +}; diff --git a/Documentation/devicetree/bindings/sound/ak4104.txt b/Documentation/devicetree/bindings/sound/ak4104.txt new file mode 100644 index 00000000000..b902ee39cf8 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ak4104.txt @@ -0,0 +1,22 @@ +AK4104 S/PDIF transmitter + +This device supports SPI mode only. + +Required properties: + + - compatible : "asahi-kasei,ak4104" + + - reg : The chip select number on the SPI bus + +Optional properties: + + - reset-gpio : a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the device starts. + +Example: + +spdif: ak4104@0 { + compatible = "asahi-kasei,ak4104"; + reg = <0>; + spi-max-frequency = <5000000>; +}; diff --git a/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt b/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt new file mode 100644 index 00000000000..9c5a9947b64 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt @@ -0,0 +1,26 @@ +* Atmel at91sam9g20ek wm8731 audio complex + +Required properties: + - compatible: "atmel,at91sam9g20ek-wm8731-audio" + - atmel,model: The user-visible name of this sound complex. + - atmel,audio-routing: A list of the connections between audio components. + - atmel,ssc-controller: The phandle of the SSC controller + - atmel,audio-codec: The phandle of the WM8731 audio codec +Optional properties: + - pinctrl-names, pinctrl-0: Please refer to pinctrl-bindings.txt + +Example: +sound { + compatible = "atmel,at91sam9g20ek-wm8731-audio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_mck>; + + atmel,model = "wm8731 @ AT91SAMG20EK"; + + atmel,audio-routing = + "Ext Spk", "LHPOUT", + "Int MIC", "MICIN"; + + atmel,ssc-controller = <&ssc0>; + atmel,audio-codec = <&wm8731>; +}; diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt index c81b5fd5a5b..a850fb9c88e 100644 --- a/Documentation/devicetree/bindings/sound/cs4271.txt +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -18,6 +18,8 @@ Optional properties: - reset-gpio: a GPIO spec to define which pin is connected to the chip's !RESET pin + - cirrus,amuteb-eq-bmutec: When given, the Codec's AMUTEB=BMUTEC flag + is enabled. Examples: diff --git a/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt index 65dec876cb2..fd40c852d7c 100644 --- a/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt +++ b/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt @@ -12,7 +12,7 @@ Required properties: Optional properties: - ti,dmic: phandle for the OMAP dmic node if the machine have it connected -- ti,jack_detection: Need to be set to <1> if the board capable to detect jack +- ti,jack_detection: Need to be present if the board capable to detect jack insertion, removal. Available audio endpoints for the audio-routing table: @@ -59,7 +59,7 @@ sound { compatible = "ti,abe-twl6040"; ti,model = "SDP4430"; - ti,jack-detection = <1>; + ti,jack-detection; ti,mclk-freq = <38400000>; ti,mcpdm = <&mcpdm>; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt new file mode 100644 index 00000000000..7b53da5cb75 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt @@ -0,0 +1,26 @@ +NVIDIA Tegra20 SFLASH controller. + +Required properties: +- compatible : should be "nvidia,tegra20-sflash". +- reg: Should contain SFLASH registers location and length. +- interrupts: Should contain SFLASH interrupts. +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for this SFLASH controller. + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +spi@7000c380 { + compatible = "nvidia,tegra20-sflash"; + reg = <0x7000c380 0x80>; + interrupts = <0 39 0x04>; + nvidia,dma-request-selector = <&apbdma 16>; + spi-max-frequency = <25000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; +}; + diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt new file mode 100644 index 00000000000..eefe15e3d95 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt @@ -0,0 +1,26 @@ +NVIDIA Tegra20/Tegra30 SLINK controller. + +Required properties: +- compatible : should be "nvidia,tegra20-slink", "nvidia,tegra30-slink". +- reg: Should contain SLINK registers location and length. +- interrupts: Should contain SLINK interrupts. +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for this SLINK controller. + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +spi@7000d600 { + compatible = "nvidia,tegra20-slink"; + reg = <0x7000d600 0x200>; + interrupts = <0 82 0x04>; + nvidia,dma-request-selector = <&apbdma 16>; + spi-max-frequency = <25000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; +}; + diff --git a/Documentation/devicetree/bindings/spi/omap-spi.txt b/Documentation/devicetree/bindings/spi/omap-spi.txt index 81df374adbb..938809c6829 100644 --- a/Documentation/devicetree/bindings/spi/omap-spi.txt +++ b/Documentation/devicetree/bindings/spi/omap-spi.txt @@ -6,7 +6,9 @@ Required properties: - "ti,omap4-spi" for OMAP4+. - ti,spi-num-cs : Number of chipselect supported by the instance. - ti,hwmods: Name of the hwmod associated to the McSPI - +- ti,pindir-d0-out-d1-in: Select the D0 pin as output and D1 as + input. The default is D0 as input and + D1 as output. Example: diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index d2c33d0f533..296015e3c63 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -12,6 +12,7 @@ The SPI master node requires the following properties: - #size-cells - should be zero. - compatible - name of SPI bus controller following generic names recommended practice. +- cs-gpios - (optional) gpios chip select. No other properties are required in the SPI bus node. It is assumed that a driver for an SPI bus device will understand that it is an SPI bus. However, the binding does not attempt to define the specific method for @@ -24,6 +25,22 @@ support describing the chip select layout. Optional property: - num-cs : total number of chipselects +If cs-gpios is used the number of chip select will automatically increased +with max(cs-gpios > hw cs) + +So if for example the controller has 2 CS lines, and the cs-gpios +property looks like this: + +cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>; + +Then it should be configured so that num_chipselect = 4 with the +following mapping: + +cs0 : &gpio1 0 0 +cs1 : native +cs2 : &gpio1 1 0 +cs3 : &gpio1 2 0 + SPI slave nodes must be children of the SPI master node and can contain the following properties. - reg - (required) chip select address of device. @@ -36,6 +53,11 @@ contain the following properties. shifted clock phase (CPHA) mode - spi-cs-high - (optional) Empty property indicating device requires chip select active high +- spi-3wire - (optional) Empty property indicating device requires + 3-wire mode. + +If a gpio chipselect is used for the SPI slave the gpio number will be passed +via the cs_gpio SPI example for an MPC5200 SPI bus: spi@f00 { diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt new file mode 100644 index 00000000000..07e04cdc0c9 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt @@ -0,0 +1,26 @@ +Atmel SPI device + +Required properties: +- compatible : should be "atmel,at91rm9200-spi". +- reg: Address and length of the register set for the device +- interrupts: Should contain spi interrupt +- cs-gpios: chipselects + +Example: + +spi1: spi@fffcc000 { + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffcc000 0x4000>; + interrupts = <13 4 5>; + #address-cells = <1>; + #size-cells = <0>; + cs-gpios = <&pioB 3 0>; + status = "okay"; + + mmc-slot@0 { + compatible = "mmc-spi-slot"; + reg = <0>; + gpios = <&pioC 4 0>; /* CD */ + spi-max-frequency = <25000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/thermal/db8500-thermal.txt b/Documentation/devicetree/bindings/thermal/db8500-thermal.txt new file mode 100644 index 00000000000..2e1c06fad81 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/db8500-thermal.txt @@ -0,0 +1,44 @@ +* ST-Ericsson DB8500 Thermal + +** Thermal node properties: + +- compatible : "stericsson,db8500-thermal"; +- reg : address range of the thermal sensor registers; +- interrupts : interrupts generated from PRCMU; +- interrupt-names : "IRQ_HOTMON_LOW" and "IRQ_HOTMON_HIGH"; +- num-trips : number of total trip points, this is required, set it 0 if none, + if greater than 0, the following properties must be defined; +- tripN-temp : temperature of trip point N, should be in ascending order; +- tripN-type : type of trip point N, should be one of "active" "passive" "hot" + "critical"; +- tripN-cdev-num : number of the cooling devices which can be bound to trip + point N, this is required if trip point N is defined, set it 0 if none, + otherwise the following cooling device names must be defined; +- tripN-cdev-nameM : name of the No. M cooling device of trip point N; + +Usually the num-trips and tripN-*** are separated in board related dts files. + +Example: +thermal@801573c0 { + compatible = "stericsson,db8500-thermal"; + reg = <0x801573c0 0x40>; + interrupts = <21 0x4>, <22 0x4>; + interrupt-names = "IRQ_HOTMON_LOW", "IRQ_HOTMON_HIGH"; + + num-trips = <3>; + + trip0-temp = <75000>; + trip0-type = "active"; + trip0-cdev-num = <1>; + trip0-cdev-name0 = "thermal-cpufreq-0"; + + trip1-temp = <80000>; + trip1-type = "active"; + trip1-cdev-num = <2>; + trip1-cdev-name0 = "thermal-cpufreq-0"; + trip1-cdev-name1 = "thermal-fan"; + + trip2-temp = <85000>; + trip2-type = "critical"; + trip2-cdev-num = <0>; +} diff --git a/Documentation/devicetree/bindings/timer/allwinner,sunxi-timer.txt b/Documentation/devicetree/bindings/timer/allwinner,sunxi-timer.txt new file mode 100644 index 00000000000..0c7b64e95a6 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/allwinner,sunxi-timer.txt @@ -0,0 +1,17 @@ +Allwinner A1X SoCs Timer Controller + +Required properties: + +- compatible : should be "allwinner,sunxi-timer" +- reg : Specifies base physical address and size of the registers. +- interrupts : The interrupt of the first timer +- clocks: phandle to the source clock (usually a 24 MHz fixed clock) + +Example: + +timer { + compatible = "allwinner,sunxi-timer"; + reg = <0x01c20c00 0x400>; + interrupts = <22>; + clocks = <&osc>; +}; diff --git a/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt b/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt new file mode 100644 index 00000000000..e019fdc3877 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nvidia,tegra20-timer.txt @@ -0,0 +1,21 @@ +NVIDIA Tegra20 timer + +The Tegra20 timer provides four 29-bit timer channels and a single 32-bit free +running counter. The first two channels may also trigger a watchdog reset. + +Required properties: + +- compatible : should be "nvidia,tegra20-timer". +- reg : Specifies base physical address and size of the registers. +- interrupts : A list of 4 interrupts; one per timer channel. + +Example: + +timer { + compatible = "nvidia,tegra20-timer"; + reg = <0x60005000 0x60>; + interrupts = <0 0 0x04 + 0 1 0x04 + 0 41 0x04 + 0 42 0x04>; +}; diff --git a/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt b/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt new file mode 100644 index 00000000000..906109d4c59 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nvidia,tegra30-timer.txt @@ -0,0 +1,23 @@ +NVIDIA Tegra30 timer + +The Tegra30 timer provides ten 29-bit timer channels, a single 32-bit free +running counter, and 5 watchdog modules. The first two channels may also +trigger a legacy watchdog reset. + +Required properties: + +- compatible : should be "nvidia,tegra30-timer", "nvidia,tegra20-timer". +- reg : Specifies base physical address and size of the registers. +- interrupts : A list of 6 interrupts; one per each of timer channels 1 + through 5, and one for the shared interrupt for the remaining channels. + +timer { + compatible = "nvidia,tegra30-timer", "nvidia,tegra20-timer"; + reg = <0x60005000 0x400>; + interrupts = <0 0 0x04 + 0 1 0x04 + 0 41 0x04 + 0 42 0x04 + 0 121 0x04 + 0 122 0x04>; +}; diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt index 2ee903fad25..273a8d5b330 100644 --- a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt +++ b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt @@ -6,11 +6,19 @@ Required properties: - reg : Address and length of the register set for the device - interrupts : Should contain the auart interrupt numbers +Optional properties: +- fsl,auart-dma-channel : The DMA channels, the first is for RX, the other + is for TX. If you add this property, it also means that you + will enable the DMA support for the auart. + Note: due to the hardware bug in imx23(see errata : 2836), + only the imx28 can enable the DMA support for the auart. + Example: auart0: serial@8006a000 { compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x8006a000 0x2000>; interrupts = <112 70 71>; + fsl,auart-dma-channel = <8 9>; }; Note: Each auart port should have an alias correctly numbered in "aliases" diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt index ba385f2e0dd..1e1145ca4f3 100644 --- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt @@ -14,7 +14,10 @@ Required properties: - "serial" if the port type is unknown. - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. -- clock-frequency : the input clock frequency for the UART. +- clock-frequency : the input clock frequency for the UART + or + clocks phandle to refer to the clk used as per Documentation/devicetree + /bindings/clock/clock-bindings.txt Optional properties: - current-speed : the current active speed of the UART. diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt index ca8fa56e9f0..ea840f7f925 100644 --- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -1,14 +1,35 @@ AM33XX MUSB GLUE - compatible : Should be "ti,musb-am33xx" + - reg : offset and length of register sets, first usbss, then for musb instances + - interrupts : usbss, musb instance interrupts in order - ti,hwmods : must be "usb_otg_hs" - multipoint : Should be "1" indicating the musb controller supports multipoint. This is a MUSB configuration-specific setting. - - num_eps : Specifies the number of endpoints. This is also a + - num-eps : Specifies the number of endpoints. This is also a MUSB configuration-specific setting. Should be set to "16" - - ram_bits : Specifies the ram address size. Should be set to "12" - - port0_mode : Should be "3" to represent OTG. "1" signifies HOST and "2" + - ram-bits : Specifies the ram address size. Should be set to "12" + - port0-mode : Should be "3" to represent OTG. "1" signifies HOST and "2" represents PERIPHERAL. - - port1_mode : Should be "1" to represent HOST. "3" signifies OTG and "2" + - port1-mode : Should be "1" to represent HOST. "3" signifies OTG and "2" represents PERIPHERAL. - power : Should be "250". This signifies the controller can supply upto 500mA when operating in host mode. + +Example: + +usb@47400000 { + compatible = "ti,musb-am33xx"; + reg = <0x47400000 0x1000 /* usbss */ + 0x47401000 0x800 /* musb instance 0 */ + 0x47401800 0x800>; /* musb instance 1 */ + interrupts = <17 /* usbss */ + 18 /* musb instance 0 */ + 19>; /* musb instance 1 */ + multipoint = <1>; + num-eps = <16>; + ram-bits = <12>; + port0-mode = <3>; + port1-mode = <3>; + power = <250>; + ti,hwmods = "usb_otg_hs"; +}; diff --git a/Documentation/devicetree/bindings/usb/ehci-orion.txt b/Documentation/devicetree/bindings/usb/ehci-orion.txt new file mode 100644 index 00000000000..6bc09ec14c4 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-orion.txt @@ -0,0 +1,15 @@ +* EHCI controller, Orion Marvell variants + +Required properties: +- compatible: must be "marvell,orion-ehci" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The EHCI interrupt + +Example: + + ehci@50000 { + compatible = "marvell,orion-ehci"; + reg = <0x50000 0x1000>; + interrupts = <19>; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 9de2b9ff9d6..902b1b1f568 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -5,6 +5,7 @@ using them to avoid name-space collisions. ad Avionic Design GmbH adi Analog Devices, Inc. +ak Asahi Kasei Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. @@ -25,6 +26,7 @@ gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. hp Hewlett Packard ibm International Business Machines (IBM) idt Integrated Device Technologies, Inc. +img Imagination Technologies Ltd. intercontrol Inter Control Group linux Linux-specific binding marvell Marvell Technology Group Ltd. @@ -34,8 +36,9 @@ national National Semiconductor nintendo Nintendo nvidia NVIDIA nxp NXP Semiconductors +onnn ON Semiconductor Corp. picochip Picochip Ltd -powervr Imagination Technologies +powervr PowerVR (deprecated, use img) qcom Qualcomm, Inc. ramtron Ramtron International realtek Realtek Semiconductor Corp. @@ -45,10 +48,12 @@ schindler Schindler sil Silicon Image simtek sirf SiRF Technology, Inc. +snps Synopsys, Inc. st STMicroelectronics stericsson ST-Ericsson ti Texas Instruments via VIA Technologies, Inc. wlf Wolfson Microelectronics wm Wondermedia Technologies, Inc. +winbond Winbond Electronics corp. xlnx Xilinx diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt new file mode 100644 index 00000000000..c60da67a5d7 --- /dev/null +++ b/Documentation/devicetree/bindings/video/exynos_dp.txt @@ -0,0 +1,80 @@ +The Exynos display port interface should be configured based on +the type of panel connected to it. + +We use two nodes: + -dp-controller node + -dptx-phy node(defined inside dp-controller node) + +For the DP-PHY initialization, we use the dptx-phy node. +Required properties for dptx-phy: + -reg: + Base address of DP PHY register. + -samsung,enable-mask: + The bit-mask used to enable/disable DP PHY. + +For the Panel initialization, we read data from dp-controller node. +Required properties for dp-controller: + -compatible: + should be "samsung,exynos5-dp". + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + -interrupt-parent: + phandle to Interrupt combiner node. + -samsung,color-space: + input video data format. + COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 + -samsung,dynamic-range: + dynamic range for input video data. + VESA = 0, CEA = 1 + -samsung,ycbcr-coeff: + YCbCr co-efficients for input video. + COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1 + -samsung,color-depth: + number of bits per colour component. + COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3 + -samsung,link-rate: + link rate supported by the panel. + LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A + -samsung,lane-count: + number of lanes supported by the panel. + LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 + +Optional properties for dp-controller: + -interlaced: + interlace scan mode. + Progressive if defined, Interlaced if not defined + -vsync-active-high: + VSYNC polarity configuration. + High if defined, Low if not defined + -hsync-active-high: + HSYNC polarity configuration. + High if defined, Low if not defined + +Example: + +SOC specific portion: + dp-controller { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x10000>; + interrupts = <10 3>; + interrupt-parent = <&combiner>; + + dptx-phy { + reg = <0x10040720>; + samsung,enable-mask = <1>; + }; + + }; + +Board Specific portion: + dp-controller { + samsung,color-space = <0>; + samsung,dynamic-range = <0>; + samsung,ycbcr-coeff = <0>; + samsung,color-depth = <1>; + samsung,link-rate = <0x0a>; + samsung,lane-count = <4>; + }; diff --git a/Documentation/devicetree/bindings/video/ssd1307fb.txt b/Documentation/devicetree/bindings/video/ssd1307fb.txt new file mode 100644 index 00000000000..3d0060cff06 --- /dev/null +++ b/Documentation/devicetree/bindings/video/ssd1307fb.txt @@ -0,0 +1,24 @@ +* Solomon SSD1307 Framebuffer Driver + +Required properties: + - compatible: Should be "solomon,ssd1307fb-<bus>". The only supported bus for + now is i2c. + - reg: Should contain address of the controller on the I2C bus. Most likely + 0x3c or 0x3d + - pwm: Should contain the pwm to use according to the OF device tree PWM + specification [0] + - reset-gpios: Should contain the GPIO used to reset the OLED display + +Optional properties: + - reset-active-low: Is the reset gpio is active on physical low? + +[0]: Documentation/devicetree/bindings/pwm/pwm.txt + +Examples: +ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7>; + reset-active-low; +}; diff --git a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt new file mode 100644 index 00000000000..2957ebb5aa7 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt @@ -0,0 +1,15 @@ +* Atmel Watchdog Timers + +** at91sam9-wdt + +Required properties: +- compatible: must be "atmel,at91sam9260-wdt". +- reg: physical base address of the controller and length of memory mapped + region. + +Example: + + watchdog@fffffd40 { + compatible = "atmel,at91sam9260-wdt"; + reg = <0xfffffd40 0x10>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt b/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt new file mode 100644 index 00000000000..d209366b4a6 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/brcm,bcm2835-pm-wdog.txt @@ -0,0 +1,13 @@ +BCM2835 Watchdog timer + +Required properties: + +- compatible : should be "brcm,bcm2835-pm-wdt" +- reg : Specifies base physical address and size of the registers. + +Example: + +watchdog { + compatible = "brcm,bcm2835-pm-wdt"; + reg = <0x7e100000 0x28>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt b/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt new file mode 100644 index 00000000000..75558ccd9a0 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt @@ -0,0 +1,12 @@ +DaVinci Watchdog Timer (WDT) Controller + +Required properties: +- compatible : Should be "ti,davinci-wdt" +- reg : Should contain WDT registers location and length + +Examples: + +wdt: wdt@2320000 { + compatible = "ti,davinci-wdt"; + reg = <0x02320000 0x80>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt new file mode 100644 index 00000000000..0b271777560 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt @@ -0,0 +1,13 @@ +Allwinner sunXi Watchdog timer + +Required properties: + +- compatible : should be "allwinner,sunxi-wdt" +- reg : Specifies base physical address and size of the registers. + +Example: + +wdt: watchdog@01c20c90 { + compatible = "allwinner,sunxi-wdt"; + reg = <0x01c20c90 0x10>; +}; diff --git a/Documentation/devicetree/usage-model.txt b/Documentation/devicetree/usage-model.txt index dca90fe22a9..ef9d06c9f8f 100644 --- a/Documentation/devicetree/usage-model.txt +++ b/Documentation/devicetree/usage-model.txt @@ -347,7 +347,7 @@ later), which will happily live at the base of the Linux /sys/devices tree. Therefore, if a DT node is at the root of the tree, then it really probably is best registered as a platform_device. -Linux board support code calls of_platform_populate(NULL, NULL, NULL) +Linux board support code calls of_platform_populate(NULL, NULL, NULL, NULL) to kick off discovery of devices at the root of the tree. The parameters are all NULL because when starting from the root of the tree, there is no need to provide a starting node (the first NULL), a |