diff options
Diffstat (limited to 'Documentation/devicetree')
10 files changed, 273 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/sound/ak4642.txt b/Documentation/devicetree/bindings/sound/ak4642.txt new file mode 100644 index 00000000000..623d4e70ae1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ak4642.txt @@ -0,0 +1,17 @@ +AK4642 I2C transmitter + +This device supports I2C mode only. + +Required properties: + + - compatible : "asahi-kasei,ak4642" or "asahi-kasei,ak4643" or "asahi-kasei,ak4648" + - reg : The chip select number on the I2C bus + +Example: + +&i2c { + ak4648: ak4648@0x12 { + compatible = "asahi-kasei,ak4642"; + reg = <0x12>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt index a850fb9c88e..e2cd1d7539e 100644 --- a/Documentation/devicetree/bindings/sound/cs4271.txt +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -20,6 +20,18 @@ Optional properties: !RESET pin - cirrus,amuteb-eq-bmutec: When given, the Codec's AMUTEB=BMUTEC flag is enabled. + - cirrus,enable-soft-reset: + The CS4271 requires its LRCLK and MCLK to be stable before its RESET + line is de-asserted. That also means that clocks cannot be changed + without putting the chip back into hardware reset, which also requires + a complete re-initialization of all registers. + + One (undocumented) workaround is to assert and de-assert the PDN bit + in the MODE2 register. This workaround can be enabled with this DT + property. + + Note that this is not needed in case the clocks are stable + throughout the entire runtime of the codec. Examples: diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt new file mode 100644 index 00000000000..be35d34e8b2 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt @@ -0,0 +1,51 @@ +NVIDIA Tegra audio complex + +Required properties: +- compatible : "nvidia,tegra-audio-wm9712" +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the WM9712's pins, and the jacks on the board: + + WM9712 pins: + + * MONOOUT + * HPOUTL + * HPOUTR + * LOUT2 + * ROUT2 + * OUT3 + * LINEINL + * LINEINR + * PHONE + * PCBEEP + * MIC1 + * MIC2 + * Mic Bias + + Board connectors: + + * Headphone + * LineIn + * Mic + +- nvidia,ac97-controller : The phandle of the Tegra AC97 controller + + +Example: + +sound { + compatible = "nvidia,tegra-audio-wm9712-colibri_t20", + "nvidia,tegra-audio-wm9712"; + nvidia,model = "Toradex Colibri T20"; + + nvidia,audio-routing = + "Headphone", "HPOUTL", + "Headphone", "HPOUTR", + "LineIn", "LINEINL", + "LineIn", "LINEINR", + "Mic", "MIC1"; + + nvidia,ac97-controller = <&ac97>; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt new file mode 100644 index 00000000000..c1454979c1e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt @@ -0,0 +1,22 @@ +NVIDIA Tegra 20 AC97 controller + +Required properties: +- compatible : "nvidia,tegra20-ac97" +- reg : Should contain AC97 controller registers location and length +- interrupts : Should contain AC97 interrupt +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for the AC97 controller +- nvidia,codec-reset-gpio : The Tegra GPIO controller's phandle and the number + of the GPIO used to reset the external AC97 codec +- nvidia,codec-sync-gpio : The Tegra GPIO controller's phandle and the number + of the GPIO corresponding with the AC97 DAP _FS line +Example: + +ac97@70002000 { + compatible = "nvidia,tegra20-ac97"; + reg = <0x70002000 0x200>; + interrupts = <0 81 0x04>; + nvidia,dma-request-selector = <&apbdma 12>; + nvidia,codec-reset-gpio = <&gpio 170 0>; + nvidia,codec-sync-gpio = <&gpio 120 0>; +}; diff --git a/Documentation/devicetree/bindings/sound/omap-twl4030.txt b/Documentation/devicetree/bindings/sound/omap-twl4030.txt index 6fae51c7f76..1ab6bc8404d 100644 --- a/Documentation/devicetree/bindings/sound/omap-twl4030.txt +++ b/Documentation/devicetree/bindings/sound/omap-twl4030.txt @@ -6,6 +6,52 @@ Required properties: - ti,mcbsp: phandle for the McBSP node - ti,codec: phandle for the twl4030 audio node +Optional properties: +- ti,mcbsp-voice: phandle for the McBSP node connected to the voice port of twl +- ti, jack-det-gpio: Jack detect GPIO +- ti,audio-routing: List of connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. + If the routing is not provided all possible connection will be available + +Available audio endpoints for the audio-routing table: + +Board connectors: + * Headset Stereophone + * Earpiece Spk + * Handsfree Spk + * Ext Spk + * Main Mic + * Sub Mic + * Headset Mic + * Carkit Mic + * Digital0 Mic + * Digital1 Mic + * Line In + +twl4030 pins: + * HSOL + * HSOR + * EARPIECE + * HFL + * HFR + * PREDRIVEL + * PREDRIVER + * CARKITL + * CARKITR + * MAINMIC + * SUBMIC + * HSMIC + * DIGIMIC0 + * DIGIMIC1 + * CARKITMIC + * AUXL + * AUXR + + * Headset Mic Bias + * Mic Bias 1 /* Used for Main Mic or Digimic0 */ + * Mic Bias 2 /* Used for Sub Mic or Digimic1 */ + Example: sound { diff --git a/Documentation/devicetree/bindings/sound/renesas,fsi.txt b/Documentation/devicetree/bindings/sound/renesas,fsi.txt new file mode 100644 index 00000000000..c5be003f413 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/renesas,fsi.txt @@ -0,0 +1,26 @@ +Renesas FSI + +Required properties: +- compatible : "renesas,sh_fsi2" or "renesas,sh_fsi" +- reg : Should contain the register physical address and length +- interrupts : Should contain FSI interrupt + +- fsia,spdif-connection : FSI is connected by S/PDFI +- fsia,stream-mode-support : FSI supports 16bit stream mode. +- fsia,use-internal-clock : FSI uses internal clock when master mode. + +- fsib,spdif-connection : same as fsia +- fsib,stream-mode-support : same as fsia +- fsib,use-internal-clock : same as fsia + +Example: + +sh_fsi2: sh_fsi2@0xec230000 { + compatible = "renesas,sh_fsi2"; + reg = <0xec230000 0x400>; + interrupts = <0 146 0x4>; + + fsia,spdif-connection; + fsia,stream-mode-support; + fsia,use-internal-clock; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt b/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt new file mode 100644 index 00000000000..4686646fb12 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt @@ -0,0 +1,14 @@ +Samsung SMDK audio complex + +Required properties: +- compatible : "samsung,smdk-wm8994" +- samsung,i2s-controller: The phandle of the Samsung I2S0 controller +- samsung,audio-codec: The phandle of the WM8994 audio codec +Example: + +sound { + compatible = "samsung,smdk-wm8994"; + + samsung,i2s-controller = <&i2s0>; + samsung,audio-codec = <&wm8994>; +}; diff --git a/Documentation/devicetree/bindings/sound/samsung-i2s.txt b/Documentation/devicetree/bindings/sound/samsung-i2s.txt new file mode 100644 index 00000000000..3070046da2e --- /dev/null +++ b/Documentation/devicetree/bindings/sound/samsung-i2s.txt @@ -0,0 +1,63 @@ +* Samsung I2S controller + +Required SoC Specific Properties: + +- compatible : "samsung,i2s-v5" +- reg: physical base address of the controller and length of memory mapped + region. +- dmas: list of DMA controller phandle and DMA request line ordered pairs. +- dma-names: identifier string for each DMA request line in the dmas property. + These strings correspond 1:1 with the ordered pairs in dmas. + +Optional SoC Specific Properties: + +- samsung,supports-6ch: If the I2S Primary sound source has 5.1 Channel + support, this flag is enabled. +- samsung,supports-rstclr: This flag should be set if I2S software reset bit + control is required. When this flag is set I2S software reset bit will be + enabled or disabled based on need. +- samsung,supports-secdai:If I2S block has a secondary FIFO and internal DMA, + then this flag is enabled. +- samsung,idma-addr: Internal DMA register base address of the audio + sub system(used in secondary sound source). + +Required Board Specific Properties: + +- gpios: The gpio specifier for data out,data in, LRCLK, CDCLK and SCLK + interface lines. The format of the gpio specifier depends on the gpio + controller. + The syntax of samsung gpio specifier is + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [mux function] + [flags and pull up/down] + [drive strength]> + +Example: + +- SoC Specific Portion: + +i2s@03830000 { + compatible = "samsung,i2s-v5"; + reg = <0x03830000 0x100>; + dmas = <&pdma0 10 + &pdma0 9 + &pdma0 8>; + dma-names = "tx", "rx", "tx-sec"; + samsung,supports-6ch; + samsung,supports-rstclr; + samsung,supports-secdai; + samsung,idma-addr = <0x03000000>; +}; + +- Board Specific Portion: + +i2s@03830000 { + gpios = <&gpz 0 2 0 0>, /* I2S_0_SCLK */ + <&gpz 1 2 0 0>, /* I2S_0_CDCLK */ + <&gpz 2 2 0 0>, /* I2S_0_LRCK */ + <&gpz 3 2 0 0>, /* I2S_0_SDI */ + <&gpz 4 2 0 0>, /* I2S_0_SDO[1] */ + <&gpz 5 2 0 0>, /* I2S_0_SDO[2] */ + <&gpz 6 2 0 0>; /* I2S_0_SDO[3] */ +}; diff --git a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt index e7b98f41fa5..f47c3f589fd 100644 --- a/Documentation/devicetree/bindings/sound/tlv320aic3x.txt +++ b/Documentation/devicetree/bindings/sound/tlv320aic3x.txt @@ -11,6 +11,12 @@ Optional properties: - gpio-reset - gpio pin number used for codec reset - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality +- ai3x-micbias-vg - MicBias Voltage required. + 1 - MICBIAS output is powered to 2.0V, + 2 - MICBIAS output is powered to 2.5V, + 3 - MICBIAS output is connected to AVDD, + If this node is not mentioned or if the value is incorrect, then MicBias + is powered down. Example: diff --git a/Documentation/devicetree/bindings/sound/wm8962.txt b/Documentation/devicetree/bindings/sound/wm8962.txt new file mode 100644 index 00000000000..dceb3b1c2bb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8962.txt @@ -0,0 +1,16 @@ +WM8962 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "wlf,wm8962" + + - reg : the I2C address of the device. + +Example: + +codec: wm8962@1a { + compatible = "wlf,wm8962"; + reg = <0x1a>; +}; |