aboutsummaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings')
-rw-r--r--Documentation/devicetree/bindings/arm/pmu.txt21
-rw-r--r--Documentation/devicetree/bindings/arm/primecell.txt21
-rw-r--r--Documentation/devicetree/bindings/crypto/fsl-sec2.txt (renamed from Documentation/devicetree/bindings/powerpc/fsl/sec.txt)2
-rw-r--r--Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt22
-rw-r--r--Documentation/devicetree/bindings/gpio/gpio.txt46
-rw-r--r--Documentation/devicetree/bindings/gpio/gpio_nvidia.txt8
-rw-r--r--Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt22
-rw-r--r--Documentation/devicetree/bindings/spi/spi_nvidia.txt5
-rw-r--r--Documentation/devicetree/bindings/tty/serial/of-serial.txt36
9 files changed, 173 insertions, 10 deletions
diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt
new file mode 100644
index 00000000000..1c044eb320c
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/pmu.txt
@@ -0,0 +1,21 @@
+* ARM Performance Monitor Units
+
+ARM cores often have a PMU for counting cpu and cache events like cache misses
+and hits. The interface to the PMU is part of the ARM ARM. The ARM PMU
+representation in the device tree should be done as under:-
+
+Required properties:
+
+- compatible : should be one of
+ "arm,cortex-a9-pmu"
+ "arm,cortex-a8-pmu"
+ "arm,arm1176-pmu"
+ "arm,arm1136-pmu"
+- interrupts : 1 combined interrupt or 1 per core.
+
+Example:
+
+pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <100 101>;
+};
diff --git a/Documentation/devicetree/bindings/arm/primecell.txt b/Documentation/devicetree/bindings/arm/primecell.txt
new file mode 100644
index 00000000000..1d5d7a870ec
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/primecell.txt
@@ -0,0 +1,21 @@
+* ARM Primecell Peripherals
+
+ARM, Ltd. Primecell peripherals have a standard id register that can be used to
+identify the peripheral type, vendor, and revision. This value can be used for
+driver matching.
+
+Required properties:
+
+- compatible : should be a specific value for peripheral and "arm,primecell"
+
+Optional properties:
+
+- arm,primecell-periphid : Value to override the h/w value with
+
+Example:
+
+serial@fff36000 {
+ compatible = "arm,pl011", "arm,primecell";
+ arm,primecell-periphid = <0x00341011>;
+};
+
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/sec.txt b/Documentation/devicetree/bindings/crypto/fsl-sec2.txt
index 2b6f2d45c45..38988ef1336 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/sec.txt
+++ b/Documentation/devicetree/bindings/crypto/fsl-sec2.txt
@@ -1,4 +1,4 @@
-Freescale SoC SEC Security Engines
+Freescale SoC SEC Security Engines versions 2.x-3.x
Required properties:
diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
new file mode 100644
index 00000000000..4363ae4b3c1
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
@@ -0,0 +1,22 @@
+* Freescale i.MX/MXC GPIO controller
+
+Required properties:
+- compatible : Should be "fsl,<soc>-gpio"
+- reg : Address and length of the register set for the device
+- interrupts : Should be the port interrupt shared by all 32 pins, if
+ one number. If two numbers, the first one is the interrupt shared
+ by low 16 pins and the second one is for high 16 pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two. The first cell is the pin number and
+ the second cell is used to specify optional parameters (currently
+ unused).
+
+Example:
+
+gpio0: gpio@73f84000 {
+ compatible = "fsl,imx51-gpio", "fsl,imx31-gpio";
+ reg = <0x73f84000 0x4000>;
+ interrupts = <50 51>;
+ gpio-controller;
+ #gpio-cells = <2>;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
index edaa84d288a..4e16ba4feab 100644
--- a/Documentation/devicetree/bindings/gpio/gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio.txt
@@ -4,17 +4,45 @@ Specifying GPIO information for devices
1) gpios property
-----------------
-Nodes that makes use of GPIOs should define them using `gpios' property,
-format of which is: <&gpio-controller1-phandle gpio1-specifier
- &gpio-controller2-phandle gpio2-specifier
- 0 /* holes are permitted, means no GPIO 3 */
- &gpio-controller4-phandle gpio4-specifier
- ...>;
+Nodes that makes use of GPIOs should specify them using one or more
+properties, each containing a 'gpio-list':
-Note that gpio-specifier length is controller dependent.
+ gpio-list ::= <single-gpio> [gpio-list]
+ single-gpio ::= <gpio-phandle> <gpio-specifier>
+ gpio-phandle : phandle to gpio controller node
+ gpio-specifier : Array of #gpio-cells specifying specific gpio
+ (controller specific)
+
+GPIO properties should be named "[<name>-]gpios". Exact
+meaning of each gpios property must be documented in the device tree
+binding for each device.
+
+For example, the following could be used to describe gpios pins to use
+as chip select lines; with chip selects 0, 1 and 3 populated, and chip
+select 2 left empty:
+
+ gpio1: gpio1 {
+ gpio-controller
+ #gpio-cells = <2>;
+ };
+ gpio2: gpio2 {
+ gpio-controller
+ #gpio-cells = <1>;
+ };
+ [...]
+ chipsel-gpios = <&gpio1 12 0>,
+ <&gpio1 13 0>,
+ <0>, /* holes are permitted, means no GPIO 2 */
+ <&gpio2 2>;
+
+Note that gpio-specifier length is controller dependent. In the
+above example, &gpio1 uses 2 cells to specify a gpio, while &gpio2
+only uses one.
gpio-specifier may encode: bank, pin position inside the bank,
whether pin is open-drain and whether pin is logically inverted.
+Exact meaning of each specifier cell is controller specific, and must
+be documented in the device tree binding for the device.
Example of the node using GPIOs:
@@ -28,8 +56,8 @@ and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller.
2) gpio-controller nodes
------------------------
-Every GPIO controller node must have #gpio-cells property defined,
-this information will be used to translate gpio-specifiers.
+Every GPIO controller node must both an empty "gpio-controller"
+property, and have #gpio-cells contain the size of the gpio-specifier.
Example of two SOC GPIO banks defined as gpio-controller nodes:
diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
new file mode 100644
index 00000000000..eb4b530d64e
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
@@ -0,0 +1,8 @@
+NVIDIA Tegra 2 GPIO controller
+
+Required properties:
+- compatible : "nvidia,tegra20-gpio"
+- #gpio-cells : Should be two. The first cell is the pin number and the
+ second cell is used to specify optional parameters:
+ - bit 0 specifies polarity (0 for normal, 1 for inverted)
+- gpio-controller : Marks the device node as a GPIO controller.
diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
new file mode 100644
index 00000000000..9841057d112
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
@@ -0,0 +1,22 @@
+* Freescale (Enhanced) Configurable Serial Peripheral Interface
+ (CSPI/eCSPI) for i.MX
+
+Required properties:
+- compatible : Should be "fsl,<soc>-cspi" or "fsl,<soc>-ecspi"
+- reg : Offset and length of the register set for the device
+- interrupts : Should contain CSPI/eCSPI interrupt
+- fsl,spi-num-chipselects : Contains the number of the chipselect
+- cs-gpios : Specifies the gpio pins to be used for chipselects.
+
+Example:
+
+ecspi@70010000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx51-ecspi";
+ reg = <0x70010000 0x4000>;
+ interrupts = <36>;
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */
+ <&gpio3 25 0>; /* GPIO4_25 */
+};
diff --git a/Documentation/devicetree/bindings/spi/spi_nvidia.txt b/Documentation/devicetree/bindings/spi/spi_nvidia.txt
new file mode 100644
index 00000000000..6b9e5189669
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi_nvidia.txt
@@ -0,0 +1,5 @@
+NVIDIA Tegra 2 SPI device
+
+Required properties:
+- compatible : should be "nvidia,tegra20-spi".
+- gpios : should specify GPIOs used for chipselect.
diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt
new file mode 100644
index 00000000000..b8b27b0aca1
--- /dev/null
+++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt
@@ -0,0 +1,36 @@
+* UART (Universal Asynchronous Receiver/Transmitter)
+
+Required properties:
+- compatible : one of:
+ - "ns8250"
+ - "ns16450"
+ - "ns16550a"
+ - "ns16550"
+ - "ns16750"
+ - "ns16850"
+ - "nvidia,tegra20-uart"
+ - "ibm,qpace-nwp-serial"
+ - "serial" if the port type is unknown.
+- reg : offset and length of the register set for the device.
+- interrupts : should contain uart interrupt.
+- clock-frequency : the input clock frequency for the UART.
+
+Optional properties:
+- current-speed : the current active speed of the UART.
+- reg-offset : offset to apply to the mapbase from the start of the registers.
+- reg-shift : quantity to shift the register offsets by.
+- reg-io-width : the size (in bytes) of the IO accesses that should be
+ performed on the device. There are some systems that require 32-bit
+ accesses to the UART (e.g. TI davinci).
+- used-by-rtas : set to indicate that the port is in use by the OpenFirmware
+ RTAS and should not be registered.
+
+Example:
+
+ uart@80230000 {
+ compatible = "ns8250";
+ reg = <0x80230000 0x100>;
+ clock-frequency = <3686400>;
+ interrupts = <10>;
+ reg-shift = <2>;
+ };