diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/fsl-usb.txt | 81 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/usb-ehci.txt | 25 |
2 files changed, 106 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/fsl-usb.txt b/Documentation/devicetree/bindings/usb/fsl-usb.txt new file mode 100644 index 00000000000..bd5723f0b67 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/fsl-usb.txt @@ -0,0 +1,81 @@ +Freescale SOC USB controllers + +The device node for a USB controller that is part of a Freescale +SOC is as described in the document "Open Firmware Recommended +Practice : Universal Serial Bus" with the following modifications +and additions : + +Required properties : + - compatible : Should be "fsl-usb2-mph" for multi port host USB + controllers, or "fsl-usb2-dr" for dual role USB controllers + or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121 + - phy_type : For multi port host USB controllers, should be one of + "ulpi", or "serial". For dual role USB controllers, should be + one of "ulpi", "utmi", "utmi_wide", or "serial". + - reg : Offset and length of the register set for the device + - port0 : boolean; if defined, indicates port0 is connected for + fsl-usb2-mph compatible controllers. Either this property or + "port1" (or both) must be defined for "fsl-usb2-mph" compatible + controllers. + - port1 : boolean; if defined, indicates port1 is connected for + fsl-usb2-mph compatible controllers. Either this property or + "port0" (or both) must be defined for "fsl-usb2-mph" compatible + controllers. + - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible + controllers. Can be "host", "peripheral", or "otg". Default to + "host" if not defined for backward compatibility. + +Recommended properties : + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties : + - fsl,invert-drvvbus : boolean; for MPC5121 USB0 only. Indicates the + port power polarity of internal PHY signal DRVVBUS is inverted. + - fsl,invert-pwr-fault : boolean; for MPC5121 USB0 only. Indicates + the PWR_FAULT signal polarity is inverted. + +Example multi port host USB controller device node : + usb@22000 { + compatible = "fsl-usb2-mph"; + reg = <22000 1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <700>; + interrupts = <27 1>; + phy_type = "ulpi"; + port0; + port1; + }; + +Example dual role USB controller device node : + usb@23000 { + compatible = "fsl-usb2-dr"; + reg = <23000 1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <700>; + interrupts = <26 1>; + dr_mode = "otg"; + phy = "ulpi"; + }; + +Example dual role USB controller device node for MPC5121ADS: + + usb@4000 { + compatible = "fsl,mpc5121-usb2-dr"; + reg = <0x4000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = < &ipic >; + interrupts = <44 0x8>; + dr_mode = "otg"; + phy_type = "utmi_wide"; + fsl,invert-drvvbus; + fsl,invert-pwr-fault; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt new file mode 100644 index 00000000000..fa18612f757 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -0,0 +1,25 @@ +USB EHCI controllers + +Required properties: + - compatible : should be "usb-ehci". + - reg : should contain at least address and length of the standard EHCI + register set for the device. Optional platform-dependent registers + (debug-port or other) can be also specified here, but only after + definition of standard EHCI registers. + - interrupts : one EHCI interrupt should be described here. +If device registers are implemented in big endian mode, the device +node should have "big-endian-regs" property. +If controller implementation operates with big endian descriptors, +"big-endian-desc" property should be specified. +If both big endian registers and descriptors are used by the controller +implementation, "big-endian" property can be specified instead of having +both "big-endian-regs" and "big-endian-desc". + +Example (Sequoia 440EPx): + ehci@e0000300 { + compatible = "ibm,usb-ehci-440epx", "usb-ehci"; + interrupt-parent = <&UIC0>; + interrupts = <1a 4>; + reg = <0 e0000300 90 0 e0000390 70>; + big-endian; + }; |