9 files changed, 95 insertions, 43 deletions
diff --git a/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt
new file mode 100644
index 00000000000..9d6dcd3fe7f
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt
@@ -0,0 +1,49 @@
+* General Purpose Input Output (GPIO) bus.
+
+Properties:
+- compatible: "cavium,octeon-3860-gpio"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the GPIO unit's register bank.
+
+- gpio-controller: This is a GPIO controller.
+
+- #gpio-cells: Must be <2>.  The first cell is the GPIO pin.
+
+- interrupt-controller: The GPIO controller is also an interrupt
+  controller, many of its pins may be configured as an interrupt
+  source.
+
+- #interrupt-cells: Must be <2>.  The first cell is the GPIO pin
+   connected to the interrupt source.  The second cell is the interrupt
+   triggering protocol and may have one of four values:
+   1 - edge triggered on the rising edge.
+   2 - edge triggered on the falling edge
+   4 - level triggered active high.
+   8 - level triggered active low.
+
+- interrupts: Interrupt routing for each pin.
+
+Example:
+
+	gpio-controller@1070000000800 {
+		#gpio-cells = <2>;
+		compatible = "cavium,octeon-3860-gpio";
+		reg = <0x10700 0x00000800 0x0 0x100>;
+		gpio-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) GPIO pin number (0..15)
+		 * 2) Triggering (1 - edge rising
+		 *		  2 - edge falling
+		 *		  4 - level active high
+		 *		  8 - level active low)
+		 */
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		/* The GPIO pin connect to 16 consecutive CUI bits */
+		interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+			     <0 20>, <0 21>, <0 22>, <0 23>,
+			     <0 24>, <0 25>, <0 26>, <0 27>,
+			     <0 28>, <0 29>, <0 30>, <0 31>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
index 4363ae4b3c1..dbd22e0df21 100644
--- a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
@@ -8,15 +8,25 @@ Required properties:
   by low 16 pins and the second one is for high 16 pins.
 - gpio-controller : Marks the device node as a gpio controller.
 - #gpio-cells : Should be two.  The first cell is the pin number and
-  the second cell is used to specify optional parameters (currently
-  unused).
+  the second cell is used to specify the gpio polarity:
+      0 = active high
+      1 = active low
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells : Should be 2.  The first cell is the GPIO number.
+  The second cell bits[3:0] is used to specify trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
 
 Example:
 
 gpio0: gpio@73f84000 {
-	compatible = "fsl,imx51-gpio", "fsl,imx31-gpio";
+	compatible = "fsl,imx51-gpio", "fsl,imx35-gpio";
 	reg = <0x73f84000 0x4000>;
 	interrupts = <50 51>;
 	gpio-controller;
 	#gpio-cells = <2>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
 };
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
index 0c35673f7a3..1e677a47b83 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
@@ -13,8 +13,9 @@ Required properties for GPIO node:
 - interrupts : Should be the port interrupt shared by all 32 pins.
 - gpio-controller : Marks the device node as a gpio controller.
 - #gpio-cells : Should be two.  The first cell is the pin number and
-  the second cell is used to specify optional parameters (currently
-  unused).
+  the second cell is used to specify the gpio polarity:
+      0 = active high
+      1 = active low
 - interrupt-controller: Marks the device node as an interrupt controller.
 - #interrupt-cells : Should be 2.  The first cell is the GPIO number.
   The second cell bits[3:0] is used to specify trigger type and level flags:
diff --git a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
index ee87467ad8d..8315ac7780e 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
@@ -26,6 +26,6 @@ Example:
                         #gpio-cells = <2>;
                         gpio-controller;
                         interrupt-controller;
-                        supports-sleepmode;
+                        st,supports-sleepmode;
                         gpio-bank = <1>;
                 };
diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt
index 8f50fe5e6c4..5375625e8cd 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt
@@ -11,14 +11,15 @@ Required properties:
      <[phandle of the gpio controller node]
       [pin number within the gpio controller]
       [mux function]
-      [pull up/down]
+      [flags and pull up/down]
       [drive strength]>
 
   Values for gpio specifier:
   - Pin number: is a value between 0 to 7.
-  - Pull Up/Down: 0 - Pull Up/Down Disabled.
-                  1 - Pull Down Enabled.
-                  3 - Pull Up Enabled.
+  - Flags and Pull Up/Down: 0 - Pull Up/Down Disabled.
+                            1 - Pull Down Enabled.
+                            3 - Pull Up Enabled.
+          Bit 16 (0x00010000) - Input is active low.
   - Drive Strength: 0 - 1x,
                     1 - 3x,
                     2 - 2x,
diff --git a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt b/Documentation/devicetree/bindings/gpio/gpio_i2c.txt
deleted file mode 100644
index 4f8ec947c6b..00000000000
--- a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt
+++ /dev/null
@@ -1,32 +0,0 @@
-Device-Tree bindings for i2c gpio driver
-
-Required properties:
-	- compatible = "i2c-gpio";
-	- gpios: sda and scl gpio
-
-
-Optional properties:
-	- i2c-gpio,sda-open-drain: sda as open drain
-	- i2c-gpio,scl-open-drain: scl as open drain
-	- i2c-gpio,scl-output-only: scl as output only
-	- i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform)
-	- i2c-gpio,timeout-ms: timeout to get data
-
-Example nodes:
-
-i2c@0 {
-	compatible = "i2c-gpio";
-	gpios = <&pioA 23 0 /* sda */
-		 &pioA 24 0 /* scl */
-		>;
-	i2c-gpio,sda-open-drain;
-	i2c-gpio,scl-open-drain;
-	i2c-gpio,delay-us = <2>;	/* ~100 kHz */
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	rv3029c2@56 {
-		compatible = "rv3029c2";
-		reg = <0x56>;
-	};
-};
diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt
index fd2bd56e719..9bb308abd22 100644
--- a/Documentation/devicetree/bindings/gpio/led.txt
+++ b/Documentation/devicetree/bindings/gpio/led.txt
@@ -55,4 +55,4 @@ run-control {
 		gpios = <&mpc8572 7 0>;
 		default-state = "on";
 	};
-}
+};
diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
index 05428f39d9a..e13787498bc 100644
--- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
@@ -27,3 +27,26 @@ Example:
 		interrupt-controller;
 		#interrupt-cells = <1>;
       };
+
+* Marvell Orion GPIO Controller
+
+Required properties:
+- compatible         : Should be "marvell,orion-gpio"
+- reg                : Address and length of the register set for controller.
+- gpio-controller    : So we know this is a gpio controller.
+- ngpio              : How many gpios this controller has.
+- interrupts	     : Up to 4 Interrupts for the controller.
+
+Optional properties:
+- mask-offset        : For SMP Orions, offset for Nth CPU
+
+Example:
+
+		gpio0: gpio@10100 {
+			compatible = "marvell,orion-gpio";
+			#gpio-cells = <2>;
+			gpio-controller;
+			reg = <0x10100 0x40>;
+			ngpio = <32>;
+			interrupts = <35>, <36>, <37>, <38>;
+		};
diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt
index 023c9526e5f..023c9526e5f 100644
--- a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
+++ b/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt