diff options
109 files changed, 960 insertions, 874 deletions
diff --git a/Documentation/RCU/checklist.txt b/Documentation/RCU/checklist.txt index 6e253407b3d..accfe2f5247 100644 --- a/Documentation/RCU/checklist.txt +++ b/Documentation/RCU/checklist.txt @@ -298,3 +298,15 @@ over a rather long period of time, but improvements are always welcome! Note that, rcu_assign_pointer() and rcu_dereference() relate to SRCU just as they do to other forms of RCU. + +15. The whole point of call_rcu(), synchronize_rcu(), and friends + is to wait until all pre-existing readers have finished before + carrying out some otherwise-destructive operation. It is + therefore critically important to -first- remove any path + that readers can follow that could be affected by the + destructive operation, and -only- -then- invoke call_rcu(), + synchronize_rcu(), or friends. + + Because these primitives only wait for pre-existing readers, + it is the caller's responsibility to guarantee safety to + any subsequent readers. diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 5ddbe350487..20d3b94703a 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -335,3 +335,12 @@ Why: In 2.6.18 the Secmark concept was introduced to replace the "compat_net" Secmark, it is time to deprecate the older mechanism and start the process of removing the old code. Who: Paul Moore <paul.moore@hp.com> +--------------------------- + +What: sysfs ui for changing p4-clockmod parameters +When: September 2009 +Why: See commits 129f8ae9b1b5be94517da76009ea956e89104ce8 and + e088e4c9cdb618675874becb91b2fd581ee707e6. + Removal is subject to fixing any remaining bugs in ACPI which may + cause the thermal throttling not to happen at the right time. +Who: Dave Jones <davej@redhat.com>, Matthew Garrett <mjg@redhat.com> diff --git a/Documentation/networking/ipv6.txt b/Documentation/networking/ipv6.txt new file mode 100644 index 00000000000..268e5c103dd --- /dev/null +++ b/Documentation/networking/ipv6.txt @@ -0,0 +1,35 @@ + +Options for the ipv6 module are supplied as parameters at load time. + +Module options may be given as command line arguments to the insmod +or modprobe command, but are usually specified in either the +/etc/modules.conf or /etc/modprobe.conf configuration file, or in a +distro-specific configuration file. + +The available ipv6 module parameters are listed below. If a parameter +is not specified the default value is used. + +The parameters are as follows: + +disable + + Specifies whether to load the IPv6 module, but disable all + its functionality. This might be used when another module + has a dependency on the IPv6 module being loaded, but no + IPv6 addresses or operations are desired. + + The possible values and their effects are: + + 0 + IPv6 is enabled. + + This is the default value. + + 1 + IPv6 is disabled. + + No IPv6 addresses will be added to interfaces, and + it will not be possible to open an IPv6 socket. + + A reboot is required to enable IPv6. + diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index f6a13451d1f..6031e179926 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -81,7 +81,7 @@ static inline void __init ldp_init_smc911x(void) } ldp_smc911x_resources[0].start = cs_mem_base + 0x0; - ldp_smc911x_resources[0].end = cs_mem_base + 0xf; + ldp_smc911x_resources[0].end = cs_mem_base + 0xff; udelay(100); eth_gpio = LDP_SMC911X_GPIO; diff --git a/arch/m68knommu/platform/5206e/config.c b/arch/m68knommu/platform/5206e/config.c index d01a5d2b755..db902540bf2 100644 --- a/arch/m68knommu/platform/5206e/config.c +++ b/arch/m68knommu/platform/5206e/config.c @@ -17,6 +17,7 @@ #include <asm/coldfire.h> #include <asm/mcfsim.h> #include <asm/mcfdma.h> +#include <asm/mcfuart.h> /***************************************************************************/ diff --git a/arch/m68knommu/platform/528x/config.c b/arch/m68knommu/platform/528x/config.c index dfdb5c2ed8e..44baeb225dc 100644 --- a/arch/m68knommu/platform/528x/config.c +++ b/arch/m68knommu/platform/528x/config.c @@ -24,7 +24,6 @@ #include <asm/coldfire.h> #include <asm/mcfsim.h> #include <asm/mcfuart.h> -#include <asm/mcfqspi.h> #ifdef CONFIG_MTD_PARTITIONS #include <linux/mtd/partitions.h> @@ -33,233 +32,6 @@ /***************************************************************************/ void coldfire_reset(void); -static void coldfire_qspi_cs_control(u8 cs, u8 command); - -/***************************************************************************/ - -#if defined(CONFIG_SPI) - -#if defined(CONFIG_WILDFIRE) -#define SPI_NUM_CHIPSELECTS 0x02 -#define SPI_PAR_VAL 0x07 /* Enable DIN, DOUT, CLK */ -#define SPI_CS_MASK 0x18 - -#define FLASH_BLOCKSIZE (1024*64) -#define FLASH_NUMBLOCKS 16 -#define FLASH_TYPE "m25p80" - -#define M25P80_CS 0 -#define MMC_CS 1 - -#ifdef CONFIG_MTD_PARTITIONS -static struct mtd_partition stm25p_partitions[] = { - /* sflash */ - [0] = { - .name = "stm25p80", - .offset = 0x00000000, - .size = FLASH_BLOCKSIZE * FLASH_NUMBLOCKS, - .mask_flags = 0 - } -}; - -#endif - -#elif defined(CONFIG_WILDFIREMOD) - -#define SPI_NUM_CHIPSELECTS 0x08 -#define SPI_PAR_VAL 0x07 /* Enable DIN, DOUT, CLK */ -#define SPI_CS_MASK 0x78 - -#define FLASH_BLOCKSIZE (1024*64) -#define FLASH_NUMBLOCKS 64 -#define FLASH_TYPE "m25p32" -/* Reserve 1M for the kernel parition */ -#define FLASH_KERNEL_SIZE (1024 * 1024) - -#define M25P80_CS 5 -#define MMC_CS 6 - -#ifdef CONFIG_MTD_PARTITIONS -static struct mtd_partition stm25p_partitions[] = { - /* sflash */ - [0] = { - .name = "kernel", - .offset = FLASH_BLOCKSIZE * FLASH_NUMBLOCKS - FLASH_KERNEL_SIZE, - .size = FLASH_KERNEL_SIZE, - .mask_flags = 0 - }, - [1] = { - .name = "image", - .offset = 0x00000000, - .size = FLASH_BLOCKSIZE * FLASH_NUMBLOCKS - FLASH_KERNEL_SIZE, - .mask_flags = 0 - }, - [2] = { - .name = "all", - .offset = 0x00000000, - .size = FLASH_BLOCKSIZE * FLASH_NUMBLOCKS, - .mask_flags = 0</ |