diff options
59 files changed, 3721 insertions, 1347 deletions
diff --git a/Documentation/devicetree/bindings/spi/efm32-spi.txt b/Documentation/devicetree/bindings/spi/efm32-spi.txt new file mode 100644 index 00000000000..a590ca51be7 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/efm32-spi.txt @@ -0,0 +1,34 @@ +* Energy Micro EFM32 SPI + +Required properties: +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- compatible: should be "efm32,spi" +- reg: Offset and length of the register set for the controller +- interrupts: pair specifying rx and tx irq +- clocks: phandle to the spi clock +- cs-gpios: see spi-bus.txt +- location: Value to write to the ROUTE register's LOCATION bitfield to configure the pinmux for the device, see datasheet for values. + +Example: + +spi1: spi@0x4000c400 { /* USART1 */ + #address-cells = <1>; + #size-cells = <0>; + compatible = "efm32,spi"; + reg = <0x4000c400 0x400>; + interrupts = <15 16>; + clocks = <&cmu 20>; + cs-gpios = <&gpio 51 1>; // D3 + location = <1>; + status = "ok"; + + ks8851@0 { + compatible = "ks8851"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&boardfpga>; + interrupts = <4>; + status = "ok"; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 296015e3c63..800dafe5b01 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -55,6 +55,16 @@ contain the following properties. chip select active high - spi-3wire - (optional) Empty property indicating device requires 3-wire mode. +- spi-tx-bus-width - (optional) The bus width(number of data wires) that + used for MOSI. Defaults to 1 if not present. +- spi-rx-bus-width - (optional) The bus width(number of data wires) that + used for MISO. Defaults to 1 if not present. + +Some SPI controllers and devices support Dual and Quad SPI transfer mode. +It allows data in SPI system transfered in 2 wires(DUAL) or 4 wires(QUAD). +Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is +only 1(SINGLE), 2(DUAL) and 4(QUAD). +Dual/Quad mode is not allowed when 3-wire mode is used. If a gpio chipselect is used for the SPI slave the gpio number will be passed via the cs_gpio diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt new file mode 100644 index 00000000000..a1fb3035a42 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -0,0 +1,42 @@ +ARM Freescale DSPI controller + +Required properties: +- compatible : "fsl,vf610-dspi" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI controller interrupt +- clocks: from common clock binding: handle to dspi clock. +- clock-names: from common clock binding: Shall be "dspi". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must contain a "default" entry. +- spi-num-chipselects : the number of the chipselect signals. +- bus-num : the slave chip chipselect signal number. +Example: + +dspi0@4002c000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,vf610-dspi"; + reg = <0x4002c000 0x1000>; + interrupts = <0 67 0x04>; + clocks = <&clks VF610_CLK_DSPI0>; + clock-names = "dspi"; + spi-num-chipselects = <5>; + bus-num = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi0_1>; + status = "okay"; + + sflash: at26df081a@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at26df081a"; + spi-max-frequency = <16000000>; + spi-cpol; + spi-cpha; + reg = <0>; + linux,modalias = "m25p80"; + modal = "at26df081a"; + }; +}; + + diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt new file mode 100644 index 00000000000..1f9641ade0b --- /dev/null +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -0,0 +1,22 @@ +TI QSPI controller. + +Required properties: +- compatible : should be "ti,dra7xxx-qspi" or "ti,am4372-qspi". +- reg: Should contain QSPI registers location and length. +- #address-cells, #size-cells : Must be present if the device has sub-nodes +- ti,hwmods: Name of the hwmod associated to the QSPI + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +qspi: qspi@4b300000 { + compatible = "ti,dra7xxx-qspi"; + reg = <0x4b300000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <25000000>; + ti,hwmods = "qspi"; +}; diff --git a/Documentation/spi/spi-summary b/Documentation/spi/spi-summary index 2331eb21414..f21edb98341 100644 --- a/Documentation/spi/spi-summary +++ b/Documentation/spi/spi-summary @@ -215,7 +215,7 @@ So for example arch/.../mach-*/board-*.c files might have code like: /* if your mach-* infrastructure doesn't support kernels that can * run on multiple boards, pdata wouldn't benefit from "__init". */ - static struct mysoc_spi_data __initdata pdata = { ... }; + static struct mysoc_spi_data pdata __initdata = { ... }; static __init board_init(void) { diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 89cbbabaff4..0170d4c4a8a 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -70,14 +70,14 @@ config SPI_ATH79 config SPI_ATMEL tristate "Atmel SPI Controller" - depends on (ARCH_AT91 || AVR32) + depends on (ARCH_AT91 || AVR32 || COMPILE_TEST) help This selects a driver for the Atmel SPI Controller, present on many AT32 (AVR32) and AT91 (ARM) chips. config SPI_BCM2835 tristate "BCM2835 SPI controller" - depends on ARCH_BCM2835 + depends on ARCH_BCM2835 || COMPILE_TEST help This selects a driver for the Broadcom BCM2835 SPI master. @@ -88,10 +88,17 @@ config SPI_BCM2835 config SPI_BFIN5XX tristate "SPI controller driver for ADI Blackfin5xx" - depends on BLACKFIN + depends on BLACKFIN && !BF60x help This is the SPI controller master driver for Blackfin 5xx processor. +config SPI_BFIN_V3 + tristate "SPI controller v3 for Blackfin" + depends on BF60x + help + This is the SPI controller v3 master driver + found on Blackfin 60x processor. + config SPI_BFIN_SPORT tristate "SPI bus via Blackfin SPORT" depends on BLACKFIN @@ -151,15 +158,22 @@ config SPI_COLDFIRE_QSPI config SPI_DAVINCI tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller" - depends on ARCH_DAVINCI + depends on ARCH_DAVINCI || ARCH_KEYSTONE select SPI_BITBANG select TI_EDMA help SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules. +config SPI_EFM32 + tristate "EFM32 SPI controller" + depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST) + select SPI_BITBANG + help + Driver for the spi controller found on Energy Micro's EFM32 SoCs. + config SPI_EP93XX tristate "Cirrus Logic EP93xx SPI controller" - depends on ARCH_EP93XX + depends on ARCH_EP93XX || COMPILE_TEST help This enables using the Cirrus EP93xx SPI controller in master mode. @@ -191,7 +205,7 @@ config SPI_GPIO config SPI_IMX tristate "Freescale i.MX SPI controllers" - depends on ARCH_MXC + depends on ARCH_MXC || COMPILE_TEST select SPI_BITBANG default m if IMX_HAVE_PLATFORM_SPI_IMX help @@ -248,6 +262,13 @@ config SPI_FSL_SPI This also enables using the Aeroflex Gaisler GRLIB SPI controller in master mode. +config SPI_FSL_DSPI + tristate "Freescale DSPI controller" + select SPI_BITBANG + help + This enables support for the Freescale DSPI controller in master + mode. VF610 platform uses the controller. + config SPI_FSL_ESPI bool "Freescale eSPI controller" depends on FSL_SOC @@ -280,20 +301,28 @@ config SPI_OMAP_UWIRE config SPI_OMAP24XX tristate "McSPI driver for OMAP" - depends on ARCH_OMAP2PLUS + depends on ARCH_OMAP2PLUS || COMPILE_TEST help SPI master controller for OMAP24XX and later Multichannel SPI (McSPI) modules. +config SPI_TI_QSPI + tristate "DRA7xxx QSPI controller support" + depends on ARCH_OMAP2PLUS || COMPILE_TEST + help + QSPI master controller for DRA7xxx used for flash devices. + This device supports single, dual and quad read support, while + it only supports single write mode. + config SPI_OMAP_100K tristate "OMAP SPI 100K" - depends on ARCH_OMAP850 || ARCH_OMAP730 + depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST help OMAP SPI 100K master controller for omap7xx boards. config SPI_ORION tristate "Orion SPI master" - depends on PLAT_ORION + depends on PLAT_ORION || COMPILE_TEST help This enables using the SPI master controller on the Orion chips. @@ -341,7 +370,7 @@ config SPI_PXA2XX_PCI config SPI_RSPI tristate "Renesas RSPI controller" - depends on SUPERH + depends on SUPERH && SH_DMAE_BASE help SPI driver for Renesas RSPI blocks. @@ -385,7 +414,7 @@ config SPI_SH_MSIOF config SPI_SH tristate "SuperH SPI controller" - depends on SUPERH + depends on SUPERH || COMPILE_TEST help SPI driver for SuperH SPI blocks. @@ -398,13 +427,13 @@ config SPI_SH_SCI config SPI_SH_HSPI tristate "SuperH HSPI controller" - depends on ARCH_SHMOBILE + depends on ARCH_SHMOBILE || COMPILE_TEST help SPI driver for SuperH HSPI blocks. config SPI_SIRF tristate "CSR SiRFprimaII SPI controller" - depends on ARCH_SIRF + depends on SIRF_DMA select SPI_BITBANG help SPI driver for CSR SiRFprimaII SoCs @@ -418,7 +447,7 @@ config SPI_MXS config SPI_TEGRA114 tristate "NVIDIA Tegra114 SPI Controller" - depends on ARCH_TEGRA && TEGRA20_APB_DMA + depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST help SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller is different than the older SoCs SPI controller and also register interface @@ -426,7 +455,7 @@ config SPI_TEGRA114 config SPI_TEGRA20_SFLASH tristate "Nvidia Tegra20 Serial flash Controller" - depends on ARCH_TEGRA + depends on ARCH_TEGRA || COMPILE_TEST help SPI driver for Nvidia Tegra20 Serial flash Controller interface. The main usecase of this controller is to use spi flash as boot @@ -434,7 +463,7 @@ config SPI_TEGRA20_SFLASH config SPI_TEGRA20_SLINK tristate "Nvidia Tegra20/Tegra30 SLINK Controller" - depends on ARCH_TEGRA && TEGRA20_APB_DMA + depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST help SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface. @@ -457,7 +486,7 @@ config SPI_TOPCLIFF_PCH config SPI_TXX9 tristate "Toshiba TXx9 SPI controller" - depends on GPIOLIB && CPU_TX49XX + depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST) help SPI driver for Toshiba TXx9 MIPS SoCs diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 33f9c09561e..ab8d8644af0 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -17,6 +17,7 @@ obj-$(CONFIG_SPI_AU1550) += spi-au1550.o obj-$(CONFIG_SPI_BCM2835) += spi-bcm2835.o obj-$(CONFIG_SPI_BCM63XX) += spi-bcm63xx.o obj-$(CONFIG_SPI_BFIN5XX) += spi-bfin5xx.o +obj-$(CONFIG_SPI_BFIN_V3) += spi-bfin-v3.o obj-$(CONFIG_SPI_BFIN_SPORT) += spi-bfin-sport.o obj-$(CONFIG_SPI_BITBANG) += spi-bitbang.o obj-$(CONFIG_SPI_BUTTERFLY) += spi-butterfly.o @@ -27,9 +28,11 @@ obj-$(CONFIG_SPI_DESIGNWARE) += spi-dw.o obj-$(CONFIG_SPI_DW_MMIO) += spi-dw-mmio.o obj-$(CONFIG_SPI_DW_PCI) += spi-dw-midpci.o spi-dw-midpci-objs := spi-dw-pci.o spi-dw-mid.o +obj-$(CONFIG_SPI_EFM32) += spi-efm32.o obj-$(CONFIG_SPI_EP93XX) += spi-ep93xx.o obj-$(CONFIG_SPI_FALCON) += spi-falcon.o obj-$(CONFIG_SPI_FSL_CPM) += spi-fsl-cpm.o +obj-$(CONFIG_SPI_FSL_DSPI) += spi-fsl-dspi.o obj-$(CONFIG_SPI_FSL_LIB) += spi-fsl-lib.o obj-$(CONFIG_SPI_FSL_ESPI) += spi-fsl-espi.o obj-$(CONFIG_SPI_FSL_SPI) += spi-fsl-spi.o @@ -46,6 +49,7 @@ obj-$(CONFIG_SPI_OCTEON) += spi-octeon.o obj-$(CONFIG_SPI_OMAP_UWIRE) += spi-omap-uwire.o obj-$(CONFIG_SPI_OMAP_100K) += spi-omap-100k.o obj-$(CONFIG_SPI_OMAP24XX) += spi-omap2-mcspi.o +obj-$(CONFIG_SPI_TI_QSPI) += spi-ti-qspi.o obj-$(CONFIG_SPI_ORION) += spi-orion.o obj-$(CONFIG_SPI_PL022) += spi-pl022.o obj-$(CONFIG_SPI_PPC4xx) += spi-ppc4xx.o diff --git a/drivers/spi/spi-altera.c b/drivers/spi/spi-altera.c index 81b9adb6e76..f38855f7653 100644 --- a/drivers/spi/spi-altera.c +++ b/drivers/spi/spi-altera.c @@ -103,16 +103,6 @@ static void altera_spi_chipsel(struct spi_device *spi, int value) } } -static int altera_spi_setupxfer(struct spi_device *spi, struct spi_transfer *t) -{ - return 0; -} - -static int altera_spi_setup(struct spi_device *spi) -{ - return 0; -} - static inline unsigned int hw_txbyte(struct altera_spi *hw, int count) { if (hw->tx) { @@ -134,7 +124,7 @@ static int altera_spi_txrx(struct spi_device *spi, struct spi_transfer *t) hw->tx = t->tx_buf; hw->rx = t->rx_buf; hw->count = 0; - hw->bytes_per_word = t->bits_per_word / 8; + hw->bytes_per_word = DIV_ROUND_UP(t->bits_per_word, 8); hw->len = t->len / hw->bytes_per_word; if (hw->irq >= 0) { @@ -150,12 +140,12 @@ static int altera_spi_txrx(struct spi_device *spi, struct spi_transfer *t) hw->imr &= ~ALTERA_SPI_CONTROL_IRRDY_MSK; writel(hw->imr, hw->base + ALTERA_SPI_CONTROL); } else { - /* send the first byte */ - writel(hw_txbyte(hw, 0), hw->base + ALTERA_SPI_TXDATA); - - while (1) { + while (hw->count < hw->len) { unsigned int rxd; + writel(hw_txbyte(hw, hw->count), + hw->base + ALTERA_SPI_TXDATA); + while (!(readl(hw->base + ALTERA_SPI_STATUS) & ALTERA_SPI_STATUS_RRDY_MSK)) cpu_relax(); @@ -174,14 +164,7 @@ static int altera_spi_txrx(struct spi_device *spi, struct spi_transfer *t) } hw->count++; - - if (hw->count < hw->len) - writel(hw_txbyte(hw, hw->count), - hw->base + ALTERA_SPI_TXDATA); - else - break; } - } return hw->count * hw->bytes_per_word; @@ -217,7 +200,7 @@ static irqreturn_t altera_spi_irq(int irq, void *dev) static int altera_spi_probe(struct platform_device *pdev) { - struct altera_spi_platform_data *platp = pdev->dev.platform_data; + struct altera_spi_platform_data *platp = dev_get_platdata(&pdev->dev); struct altera_spi *hw; struct spi_master *master; struct resource *res; @@ -231,7 +214,6 @@ static int altera_spi_probe(struct platform_device *pdev) master->bus_num = pdev->id; master->num_chipselect = 16; master->mode_bits = SPI_CS_HIGH; - master->setup = altera_spi_setup; hw = spi_master_get_devdata(master); platform_set_drvdata(pdev, hw); @@ -240,21 +222,16 @@ static int altera_spi_probe(struct platform_device *pdev) hw->bitbang.master = spi_master_get(master); if (!hw->bitbang.master) return err; - hw->bitbang.setup_transfer = altera_spi_setupxfer; hw->bitbang.chipselect = altera_spi_chipsel; hw->bitbang.txrx_bufs = altera_spi_txrx; /* find and map our resources */ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!res) - goto exit_busy; - if (!devm_request_mem_region(&pdev->dev, res->start, resource_size(res), - pdev->name)) - goto exit_busy; - hw->base = devm_ioremap_nocache(&pdev->dev, res->start, - resource_size(res)); - if (!hw->base) - goto exit_busy; + hw->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(hw->base)) { + err = PTR_ERR(hw->base); + goto exit; + } /* program defaults into the registers */ hw->imr = 0; /* disable spi interrupts */ writel(hw->imr, hw->base + ALTERA_SPI_CONTROL); @@ -281,9 +258,6 @@ static int altera_spi_probe(struct platform_device *pdev) dev_info(&pdev->dev, "base %p, irq %d\n", hw->base, hw->irq); return 0; - -exit_busy: - err = -EBUSY; exit: spi_master_put(master); return err; diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c index 0e06407a467..37bad952ab3 100644 --- a/drivers/spi/spi-ath79.c +++ b/drivers/spi/spi-ath79.c @@ -221,7 +221,7 @@ static int ath79_spi_probe(struct platform_device *pdev) sp = spi_master_get_devdata(master); platform_set_drvdata(pdev, sp); - pdata = pdev->dev.platform_data; + pdata = dev_get_platdata(&pdev->dev); master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32); master->setup = ath79_spi_setup; diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c index ea1ec009f44..fd7cc566095 100644 --- a/drivers/spi/spi-atmel.c +++ b/drivers/spi/spi-atmel.c @@ -360,12 +360,12 @@ static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi) gpio_set_value(asd->npcs_pin, !active); } -static void atmel_spi_lock(struct atmel_spi *as) +static void atmel_spi_lock(struct atmel_spi *as) __acquires(&as->lock) { spin_lock_irqsave(&as->lock, as->flags); } -static void atmel_spi_unlock(struct atmel_spi *as) +static void atmel_spi_unlock(struct atmel_spi *as) __releases(&as->lock) { spin_unlock_irqrestore(&as->lock, as->flags); } @@ -629,9 +629,9 @@ static int atmel_spi_next_xfer_dma_submit(struct spi_master *master, goto err_dma; dev_dbg(master->dev.parent, - " start dma xfer %p: len %u tx %p/%08x rx %p/%08x\n", - xfer, xfer->len, xfer->tx_buf, xfer->tx_dma, - xfer->rx_buf, xfer->rx_dma); + " start dma xfer %p: len %u tx %p/%08llx rx %p/%08llx\n", + xfer, xfer->len, xfer->tx_buf, (unsigned long long)xfer->tx_dma, + xfer->rx_buf, (unsigned long long)xfer->rx_dma); /* Enable relevant interrupts */ spi_writel(as, IER, SPI_BIT(OVRES)); @@ -732,9 +732,10 @@ static void atmel_spi_pdc_next_xfer(struct spi_master *master, spi_writel(as, TCR, len); dev_dbg(&msg->spi->dev, - " start xfer %p: len %u tx %p/%08x rx %p/%08x\n", - xfer, xfer->len, xfer->tx_buf, xfer->tx_dma, - xfer->rx_buf, xfer->rx_dma); + " start xfer %p: len %u tx %p/%08llx rx %p/%08llx\n", + xfer, xfer->len, xfer->tx_buf, + (unsigned long long)xfer->tx_dma, xfer->rx_buf, + (unsigned long long)xfer->rx_dma); } else { xfer = as->next_transfer; remaining = as->next_remaining_bytes; @@ -771,9 +772,10 @@ static void atmel_spi_pdc_next_xfer(struct spi_master *master, spi_writel(as, TNCR, len); dev_dbg(&msg->spi->dev, - " next xfer %p: len %u tx %p/%08x rx %p/%08x\n", - xfer, xfer->len, xfer->tx_buf, xfer->tx_dma, - xfer->rx_buf, xfer->rx_dma); + " next xfer %p: len %u tx %p/%08llx rx %p/%08llx\n", + xfer, xfer->len, xfer->tx_buf, + (unsigned long long)xfer->tx_dma, xfer->rx_buf, + (unsigned long long)xfer->rx_dma); ieval = SPI_BIT(ENDRX) | SPI_BIT(OVRES); } else { spi_writel(as, RNCR, 0); @@ -1579,7 +1581,9 @@ static int atmel_spi_probe(struct platform_device *pdev) goto out_unmap_regs; /* Initialize the hardware */ - clk_enable(clk); + ret = clk_prepare_enable(clk); + if (ret) + goto out_unmap_regs; spi_writel(as, CR, SPI_BIT(SWRST)); spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */ if (as->caps.has_wdrbt) { @@ -1609,7 +1613,7 @@ out_free_dma: spi_writel(as, CR, SPI_BIT(SWRST)); spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */ - clk_disable(clk); + clk_disable_unprepare(clk); free_irq(irq, master); out_unmap_regs: iounmap(as->regs); @@ -1661,7 +1665,7 @@ static int atmel_spi_remove(struct platform_device *pdev) dma_free_coherent(&pdev->dev, BUFFE |