diff options
78 files changed, 574 insertions, 419 deletions
diff --git a/Documentation/hwmon/coretemp b/Documentation/hwmon/coretemp index fa8776ab9b1..84d46c0c71a 100644 --- a/Documentation/hwmon/coretemp +++ b/Documentation/hwmon/coretemp @@ -35,13 +35,6 @@ the Out-Of-Spec bit. Following table summarizes the exported sysfs files: All Sysfs entries are named with their core_id (represented here by 'X'). tempX_input - Core temperature (in millidegrees Celsius). tempX_max - All cooling devices should be turned on (on Core2). - Initialized with IA32_THERM_INTERRUPT. When the CPU - temperature reaches this temperature, an interrupt is - generated and tempX_max_alarm is set. -tempX_max_hyst - If the CPU temperature falls below than temperature, - an interrupt is generated and tempX_max_alarm is reset. -tempX_max_alarm - Set if the temperature reaches or exceeds tempX_max. - Reset if the temperature drops to or below tempX_max_hyst. tempX_crit - Maximum junction temperature (in millidegrees Celsius). tempX_crit_alarm - Set when Out-of-spec bit is set, never clears. Correct CPU operation is no longer guaranteed. @@ -49,9 +42,10 @@ tempX_label - Contains string "Core X", where X is processor number. For Package temp, this will be "Physical id Y", where Y is the package number. -The TjMax temperature is set to 85 degrees C if undocumented model specific -register (UMSR) 0xee has bit 30 set. If not the TjMax is 100 degrees C as -(sometimes) documented in processor datasheet. +On CPU models which support it, TjMax is read from a model-specific register. +On other models, it is set to an arbitrary value based on weak heuristics. +If these heuristics don't work for you, you can pass the correct TjMax value +as a module parameter (tjmax). Appendix A. Known TjMax lists (TBD): Some information comes from ark.intel.com diff --git a/Documentation/vm/transhuge.txt b/Documentation/vm/transhuge.txt index 0924aaca330..29bdf62aac0 100644 --- a/Documentation/vm/transhuge.txt +++ b/Documentation/vm/transhuge.txt @@ -123,10 +123,11 @@ be automatically shutdown if it's set to "never". khugepaged runs usually at low frequency so while one may not want to invoke defrag algorithms synchronously during the page faults, it should be worth invoking defrag at least in khugepaged. However it's -also possible to disable defrag in khugepaged: +also possible to disable defrag in khugepaged by writing 0 or enable +defrag in khugepaged by writing 1: -echo yes >/sys/kernel/mm/transparent_hugepage/khugepaged/defrag -echo no >/sys/kernel/mm/transparent_hugepage/khugepaged/defrag +echo 0 >/sys/kernel/mm/transparent_hugepage/khugepaged/defrag +echo 1 >/sys/kernel/mm/transparent_hugepage/khugepaged/defrag You can also control how many pages khugepaged should scan at each pass: @@ -1,7 +1,7 @@ VERSION = 3 PATCHLEVEL = 1 SUBLEVEL = 0 -EXTRAVERSION = -rc7 +EXTRAVERSION = -rc8 NAME = "Divemaster Edition" # *DOCUMENTATION* diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 3269576dbfa..3146ed3f6ec 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1283,6 +1283,20 @@ config ARM_ERRATA_364296 processor into full low interrupt latency mode. ARM11MPCore is not affected. +config ARM_ERRATA_764369 + bool "ARM errata: Data cache line maintenance operation by MVA may not succeed" + depends on CPU_V7 && SMP + help + This option enables the workaround for erratum 764369 + affecting Cortex-A9 MPCore with two or more processors (all + current revisions). Under certain timing circumstances, a data + cache line maintenance operation by MVA targeting an Inner + Shareable memory region may fail to proceed up to either the + Point of Coherency or to the Point of Unification of the + system. This workaround adds a DSB instruction before the + relevant cache maintenance functions and sets a specific bit + in the diagnostic control register of the SCU. + endmenu source "arch/arm/common/Kconfig" diff --git a/arch/arm/include/asm/futex.h b/arch/arm/include/asm/futex.h index 8c73900da9e..253cc86318b 100644 --- a/arch/arm/include/asm/futex.h +++ b/arch/arm/include/asm/futex.h @@ -25,17 +25,17 @@ #ifdef CONFIG_SMP -#define __futex_atomic_op(insn, ret, oldval, uaddr, oparg) \ +#define __futex_atomic_op(insn, ret, oldval, tmp, uaddr, oparg) \ smp_mb(); \ __asm__ __volatile__( \ - "1: ldrex %1, [%2]\n" \ + "1: ldrex %1, [%3]\n" \ " " insn "\n" \ - "2: strex %1, %0, [%2]\n" \ - " teq %1, #0\n" \ + "2: strex %2, %0, [%3]\n" \ + " teq %2, #0\n" \ " bne 1b\n" \ " mov %0, #0\n" \ - __futex_atomic_ex_table("%4") \ - : "=&r" (ret), "=&r" (oldval) \ + __futex_atomic_ex_table("%5") \ + : "=&r" (ret), "=&r" (oldval), "=&r" (tmp) \ : "r" (uaddr), "r" (oparg), "Ir" (-EFAULT) \ : "cc", "memory") @@ -73,14 +73,14 @@ futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr, #include <linux/preempt.h> #include <asm/domain.h> -#define __futex_atomic_op(insn, ret, oldval, uaddr, oparg) \ +#define __futex_atomic_op(insn, ret, oldval, tmp, uaddr, oparg) \ __asm__ __volatile__( \ - "1: " T(ldr) " %1, [%2]\n" \ + "1: " T(ldr) " %1, [%3]\n" \ " " insn "\n" \ - "2: " T(str) " %0, [%2]\n" \ + "2: " T(str) " %0, [%3]\n" \ " mov %0, #0\n" \ - __futex_atomic_ex_table("%4") \ - : "=&r" (ret), "=&r" (oldval) \ + __futex_atomic_ex_table("%5") \ + : "=&r" (ret), "=&r" (oldval), "=&r" (tmp) \ : "r" (uaddr), "r" (oparg), "Ir" (-EFAULT) \ : "cc", "memory") @@ -117,7 +117,7 @@ futex_atomic_op_inuser (int encoded_op, u32 __user *uaddr) int cmp = (encoded_op >> 24) & 15; int oparg = (encoded_op << 8) >> 20; int cmparg = (encoded_op << 20) >> 20; - int oldval = 0, ret; + int oldval = 0, ret, tmp; if (encoded_op & (FUTEX_OP_OPARG_SHIFT << 28)) oparg = 1 << oparg; @@ -129,19 +129,19 @@ futex_atomic_op_inuser (int encoded_op, u32 __user *uaddr) switch (op) { case FUTEX_OP_SET: - __futex_atomic_op("mov %0, %3", ret, oldval, uaddr, oparg); + __futex_atomic_op("mov %0, %4", ret, oldval, tmp, uaddr, oparg); break; case FUTEX_OP_ADD: - __futex_atomic_op("add %0, %1, %3", ret, oldval, uaddr, oparg); + __futex_atomic_op("add %0, %1, %4", ret, oldval, tmp, uaddr, oparg); break; case FUTEX_OP_OR: - __futex_atomic_op("orr %0, %1, %3", ret, oldval, uaddr, oparg); + __futex_atomic_op("orr %0, %1, %4", ret, oldval, tmp, uaddr, oparg); break; case FUTEX_OP_ANDN: - __futex_atomic_op("and %0, %1, %3", ret, oldval, uaddr, ~oparg); + __futex_atomic_op("and %0, %1, %4", ret, oldval, tmp, uaddr, ~oparg); break; case FUTEX_OP_XOR: - __futex_atomic_op("eor %0, %1, %3", ret, oldval, uaddr, oparg); + __futex_atomic_op("eor %0, %1, %4", ret, oldval, tmp, uaddr, oparg); break; default: ret = -ENOSYS; diff --git a/arch/arm/include/asm/unistd.h b/arch/arm/include/asm/unistd.h index 2c04ed5efeb..c60a2944f95 100644 --- a/arch/arm/include/asm/unistd.h +++ b/arch/arm/include/asm/unistd.h @@ -478,8 +478,8 @@ /* * Unimplemented (or alternatively implemented) syscalls */ -#define __IGNORE_fadvise64_64 1 -#define __IGNORE_migrate_pages 1 +#define __IGNORE_fadvise64_64 +#define __IGNORE_migrate_pages #endif /* __KERNEL__ */ #endif /* __ASM_ARM_UNISTD_H */ diff --git a/arch/arm/kernel/smp_scu.c b/arch/arm/kernel/smp_scu.c index 79ed5e7f204..7fcddb75c87 100644 --- a/arch/arm/kernel/smp_scu.c +++ b/arch/arm/kernel/smp_scu.c @@ -13,6 +13,7 @@ #include <asm/smp_scu.h> #include <asm/cacheflush.h> +#include <asm/cputype.h> #define SCU_CTRL 0x00 #define SCU_CONFIG 0x04 @@ -37,6 +38,15 @@ void __init scu_enable(void __iomem *scu_base) { u32 scu_ctrl; +#ifdef CONFIG_ARM_ERRATA_764369 + /* Cortex-A9 only */ + if ((read_cpuid(CPUID_ID) & 0xff0ffff0) == 0x410fc090) { + scu_ctrl = __raw_readl(scu_base + 0x30); + if (!(scu_ctrl & 1)) + __raw_writel(scu_ctrl | 0x1, scu_base + 0x30); + } +#endif + scu_ctrl = __raw_readl(scu_base + SCU_CTRL); /* already enabled? */ if (scu_ctrl & 1) diff --git a/arch/arm/kernel/vmlinux.lds.S b/arch/arm/kernel/vmlinux.lds.S index bf977f8514f..4e66f62b8d4 100644 --- a/arch/arm/kernel/vmlinux.lds.S +++ b/arch/arm/kernel/vmlinux.lds.S @@ -23,8 +23,10 @@ #if defined(CONFIG_SMP_ON_UP) && !defined(CONFIG_DEBUG_SPINLOCK) #define ARM_EXIT_KEEP(x) x +#define ARM_EXIT_DISCARD(x) #else #define ARM_EXIT_KEEP(x) +#define ARM_EXIT_DISCARD(x) x #endif OUTPUT_ARCH(arm) @@ -39,6 +41,11 @@ jiffies = jiffies_64 + 4; SECTIONS { /* + * XXX: The linker does not define how output sections are + * assigned to input sections when there are multiple statements + * matching the same input section name. There is no documented + * order of matching. + * * unwind exit sections must be discarded before the rest of the * unwind sections get included. */ @@ -47,6 +54,9 @@ SECTIONS *(.ARM.extab.exit.text) ARM_CPU_DISCARD(*(.ARM.exidx.cpuexit.text)) ARM_CPU_DISCARD(*(.ARM.extab.cpuexit.text)) + ARM_EXIT_DISCARD(EXIT_TEXT) + ARM_EXIT_DISCARD(EXIT_DATA) + EXIT_CALL #ifndef CONFIG_HOTPLUG *(.ARM.exidx.devexit.text) *(.ARM.extab.devexit.text) @@ -58,6 +68,8 @@ SECTIONS #ifndef CONFIG_SMP_ON_UP *(.alt.smp.init) #endif + *(.discard) + *(.discard.*) } #ifdef CONFIG_XIP_KERNEL @@ -279,9 +291,6 @@ SECTIONS STABS_DEBUG .comment 0 : { *(.comment) } - - /* Default discards */ - DISCARDS } /* diff --git a/arch/arm/mach-exynos4/clock.c b/arch/arm/mach-exynos4/clock.c index 79d6cd0c8e7..86964d2e9e1 100644 --- a/arch/arm/mach-exynos4/clock.c +++ b/arch/arm/mach-exynos4/clock.c @@ -899,8 +899,7 @@ static struct clksrc_clk clksrcs[] = { .reg_div = { .reg = S5P_CLKDIV_CAM, .shift = 28, .size = 4 }, }, { .clk = { - .name = "sclk_cam", - .devname = "exynos4-fimc.0", + .name = "sclk_cam0", .enable = exynos4_clksrc_mask_cam_ctrl, .ctrlbit = (1 << 16), }, @@ -909,8 +908,7 @@ static struct clksrc_clk clksrcs[] = { .reg_div = { .reg = S5P_CLKDIV_CAM, .shift = 16, .size = 4 }, }, { .clk = { - .name = "sclk_cam", - .devname = "exynos4-fimc.1", + .name = "sclk_cam1", .enable = exynos4_clksrc_mask_cam_ctrl, .ctrlbit = (1 << 20), }, diff --git a/arch/arm/mach-s3c2443/clock.c b/arch/arm/mach-s3c2443/clock.c index a1a7176675b..38058af4897 100644 --- a/arch/arm/mach-s3c2443/clock.c +++ b/arch/arm/mach-s3c2443/clock.c @@ -128,7 +128,7 @@ static int s3c2443_armclk_setrate(struct clk *clk, unsigned long rate) unsigned long clkcon0; clkcon0 = __raw_readl(S3C2443_CLKDIV0); - clkcon0 &= S3C2443_CLKDIV0_ARMDIV_MASK; + clkcon0 &= ~S3C2443_CLKDIV0_ARMDIV_MASK; clkcon0 |= val << S3C2443_CLKDIV0_ARMDIV_SHIFT; __raw_writel(clkcon0, S3C2443_CLKDIV0); } diff --git a/arch/arm/mach-s5pv210/clock.c b/arch/arm/mach-s5pv210/clock.c index 52a8e607bcc..f5f8fa89679 100644 --- a/arch/arm/mach-s5pv210/clock.c +++ b/arch/arm/mach-s5pv210/clock.c @@ -815,8 +815,7 @@ static struct clksrc_clk clksrcs[] = { .reg_div = { .reg = S5P_CLK_DIV3, .shift = 20, .size = 4 }, }, { .clk = { - .name = "sclk_cam", - .devname = "s5pv210-fimc.0", + .name = "sclk_cam0", .enable = s5pv210_clk_mask0_ctrl, .ctrlbit = (1 << 3), }, @@ -825,8 +824,7 @@ static struct clksrc_clk clksrcs[] = { .reg_div = { .reg = S5P_CLK_DIV1, .shift = 12, .size = 4 }, }, { .clk = { - .name = "sclk_cam", - .devname = "s5pv210-fimc.1", + .name = "sclk_cam1", .enable = s5pv210_clk_mask0_ctrl, .ctrlbit = (1 << 4), }, diff --git a/arch/arm/mm/cache-v7.S b/arch/arm/mm/cache-v7.S index 3b24bfa3b82..07c4bc8ea0a 100644 --- a/arch/arm/mm/cache-v7.S +++ b/arch/arm/mm/cache-v7.S @@ -174,6 +174,10 @@ ENTRY(v7_coherent_user_range) dcache_line_size r2, r3 sub r3, r2, #1 bic r12, r0, r3 +#ifdef CONFIG_ARM_ERRATA_764369 + ALT_SMP(W(dsb)) + ALT_UP(W(nop)) +#endif 1: USER( mcr p15, 0, r12, c7, c11, 1 ) @ clean D line to the point of unification add r12, r12, r2 @@ -223,6 +227,10 @@ ENTRY(v7_flush_kern_dcache_area) add r1, r0, r1 sub r3, r2, #1 bic r0, r0, r3 +#ifdef CONFIG_ARM_ERRATA_764369 + ALT_SMP(W(dsb)) + ALT_UP(W(nop)) +#endif 1: mcr p15, 0, r0, c7, c14, 1 @ clean & invalidate D line / unified line add r0, r0, r2 @@ -247,6 +255,10 @@ v7_dma_inv_range: sub r3, r2, #1 tst r0, r3 bic r0, r0, r3 +#ifdef CONFIG_ARM_ERRATA_764369 + ALT_SMP(W(dsb)) + ALT_UP(W(nop)) +#endif mcrne p15, 0, r0, c7, c14, 1 @ clean & invalidate D / U line tst r1, r3 @@ -270,6 +282,10 @@ v7_dma_clean_range: dcache_line_size r2, r3 sub r3, r2, #1 bic r0, r0, r3 +#ifdef CONFIG_ARM_ERRATA_764369 + ALT_SMP(W(dsb)) + ALT_UP(W(nop)) +#endif 1: mcr p15, 0, r0, c7, c10, 1 @ clean D / U line add r0, r0, r2 @@ -288,6 +304,10 @@ ENTRY(v7_dma_flush_range) dcache_line_size r2, r3 sub r3, r2, #1 bic r0, r0, r3 +#ifdef CONFIG_ARM_ERRATA_764369 + ALT_SMP(W(dsb)) + ALT_UP(W(nop)) +#endif 1: mcr p15, 0, r0, c7, c14, 1 @ clean & invalidate D / U line add r0, r0, r2 diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c index 0a0a1e7c20d..c3ff82f92d9 100644 --- a/arch/arm/mm/dma-mapping.c +++ b/arch/arm/mm/dma-mapping.c @@ -324,6 +324,8 @@ __dma_alloc(struct device *dev, size_t size, dma_addr_t *handle, gfp_t gfp, if (addr) *handle = pfn_to_dma(dev, page_to_pfn(page)); + else + __dma_free_buffer(page, size); return addr; } diff --git a/arch/arm/plat-s5p/irq-gpioint.c b/arch/arm/plat-s5p/irq-gpioint.c index f71078ef6bb..f88216d2399 100644 --- a/arch/arm/plat-s5p/irq-gpioint.c +++ b/arch/arm/plat-s5p/irq-gpioint.c @@ -114,17 +114,18 @@ static __init int s5p_gpioint_add(struct s3c_gpio_chip *chip) { static int used_gpioint_groups = 0; int group = chip->group; - struct s5p_gpioint_bank *bank = NULL; + struct s5p_gpioint_bank *b, *bank = NULL; struct irq_chip_generic *gc; struct irq_chip_type *ct; if (used_gpioint_groups >= S5P_GPIOINT_GROUP_COUNT) return -ENOMEM; - list_for_each_entry(bank, &banks, list) { - if (group >= bank->start && - group |