diff options
25 files changed, 1880 insertions, 1544 deletions
diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt new file mode 100644 index 00000000000..5ddb2e9efaa --- /dev/null +++ b/Documentation/devicetree/bindings/bus/ti-gpmc.txt @@ -0,0 +1,84 @@ +Device tree bindings for OMAP general purpose memory controllers (GPMC) + +The actual devices are instantiated from the child nodes of a GPMC node. + +Required properties: + + - compatible: Should be set to one of the following: + + ti,omap2420-gpmc (omap2420) + ti,omap2430-gpmc (omap2430) + ti,omap3430-gpmc (omap3430 & omap3630) + ti,omap4430-gpmc (omap4430 & omap4460 & omap543x) + ti,am3352-gpmc (am335x devices) + + - reg: A resource specifier for the register space + (see the example below) + - ti,hwmods: Should be set to "ti,gpmc" until the DT transition is + completed. + - #address-cells: Must be set to 2 to allow memory address translation + - #size-cells: Must be set to 1 to allow CS address passing + - gpmc,num-cs: The maximum number of chip-select lines that controller + can support. + - gpmc,num-waitpins: The maximum number of wait pins that controller can + support. + - ranges: Must be set up to reflect the memory layout with four + integer values for each chip-select line in use: + + <cs-number> 0 <physical address of mapping> <size> + + Currently, calculated values derived from the contents + of the per-CS register GPMC_CONFIG7 (as set up by the + bootloader) are used for the physical address decoding. + As this will change in the future, filling correct + values here is a requirement. + +Timing properties for child nodes. All are optional and default to 0. + + - gpmc,sync-clk: Minimum clock period for synchronous mode, in picoseconds + + Chip-select signal timings corresponding to GPMC_CONFIG2: + - gpmc,cs-on: Assertion time + - gpmc,cs-rd-off: Read deassertion time + - gpmc,cs-wr-off: Write deassertion time + + ADV signal timings corresponding to GPMC_CONFIG3: + - gpmc,adv-on: Assertion time + - gpmc,adv-rd-off: Read deassertion time + - gpmc,adv-wr-off: Write deassertion time + + WE signals timings corresponding to GPMC_CONFIG4: + - gpmc,we-on: Assertion time + - gpmc,we-off: Deassertion time + + OE signals timings corresponding to GPMC_CONFIG4: + - gpmc,oe-on: Assertion time + - gpmc,oe-off: Deassertion time + + Access time and cycle time timings corresponding to GPMC_CONFIG5: + - gpmc,page-burst-access: Multiple access word delay + - gpmc,access: Start-cycle to first data valid delay + - gpmc,rd-cycle: Total read cycle time + - gpmc,wr-cycle: Total write cycle time + +The following are only applicable to OMAP3+ and AM335x: + - gpmc,wr-access + - gpmc,wr-data-mux-bus + + +Example for an AM33xx board: + + gpmc: gpmc@50000000 { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x50000000 0x2000>; + interrupts = <100>; + + gpmc,num-cs = <8>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */ + + /* child nodes go here */ + }; diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt new file mode 100644 index 00000000000..e7f8d7ed47e --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -0,0 +1,80 @@ +Device tree bindings for GPMC connected NANDs + +GPMC connected NAND (found on OMAP boards) are represented as child nodes of +the GPMC controller with a name of "nand". + +All timing relevant properties as well as generic gpmc child properties are +explained in a separate documents - please refer to +Documentation/devicetree/bindings/bus/ti-gpmc.txt + +For NAND specific properties such as ECC modes or bus width, please refer to +Documentation/devicetree/bindings/mtd/nand.txt + + +Required properties: + + - reg: The CS line the peripheral is connected to + +Optional properties: + + - nand-bus-width: Set this numeric value to 16 if the hardware + is wired that way. If not specified, a bus + width of 8 is assumed. + + - ti,nand-ecc-opt: A string setting the ECC layout to use. One of: + + "sw" Software method (default) + "hw" Hardware method + "hw-romcode" gpmc hamming mode method & romcode layout + "bch4" 4-bit BCH ecc code + "bch8" 8-bit BCH ecc code + + - elm_id: Specifies elm device node. This is required to support BCH + error correction using ELM module. + +For inline partiton table parsing (optional): + + - #address-cells: should be set to 1 + - #size-cells: should be set to 1 + +Example for an AM33xx board: + + gpmc: gpmc@50000000 { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x50000000 0x1000000>; + interrupts = <100>; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */ + elm_id = <&elm>; + + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <16>; + ti,nand-ecc-opt = "bch8"; + + gpmc,sync-clk = <0>; + gpmc,cs-on = <0>; + gpmc,cs-rd-off = <44>; + gpmc,cs-wr-off = <44>; + gpmc,adv-on = <6>; + gpmc,adv-rd-off = <34>; + gpmc,adv-wr-off = <44>; + gpmc,we-off = <40>; + gpmc,oe-off = <54>; + gpmc,access = <64>; + gpmc,rd-cycle = <82>; + gpmc,wr-cycle = <82>; + gpmc,wr-access = <40>; + gpmc,wr-data-mux-bus = <0>; + + #address-cells = <1>; + #size-cells = <1>; + + /* partitions go here */ + }; + }; + diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt new file mode 100644 index 00000000000..deec9da224a --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt @@ -0,0 +1,43 @@ +Device tree bindings for GPMC connected OneNANDs + +GPMC connected OneNAND (found on OMAP boards) are represented as child nodes of +the GPMC controller with a name of "onenand". + +All timing relevant properties as well as generic gpmc child properties are +explained in a separate documents - please refer to +Documentation/devicetree/bindings/bus/ti-gpmc.txt + +Required properties: + + - reg: The CS line the peripheral is connected to + +Optional properties: + + - dma-channel: DMA Channel index + +For inline partiton table parsing (optional): + + - #address-cells: should be set to 1 + - #size-cells: should be set to 1 + +Example for an OMAP3430 board: + + gpmc: gpmc@6e000000 { + compatible = "ti,omap3430-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x6e000000 0x1000000>; + interrupts = <20>; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <4>; + #address-cells = <2>; + #size-cells = <1>; + + onenand@0 { + reg = <0 0 0>; /* CS0, offset 0 */ + + #address-cells = <1>; + #size-cells = <1>; + + /* partitions go here */ + }; + }; diff --git a/arch/arm/mach-omap2/gpmc-nand.c b/arch/arm/mach-omap2/gpmc-nand.c index db969a5c499..afc1e8c32d6 100644 --- a/arch/arm/mach-omap2/gpmc-nand.c +++ b/arch/arm/mach-omap2/gpmc-nand.c @@ -89,20 +89,21 @@ static int omap2_nand_gpmc_retime( return 0; } -static bool __init gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt) +static bool gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt) { /* support only OMAP3 class */ - if (!cpu_is_omap34xx()) { + if (!cpu_is_omap34xx() && !soc_is_am33xx()) { pr_err("BCH ecc is not supported on this CPU\n"); return 0; } /* - * For now, assume 4-bit mode is only supported on OMAP3630 ES1.x, x>=1. - * Other chips may be added if confirmed to work. + * For now, assume 4-bit mode is only supported on OMAP3630 ES1.x, x>=1 + * and AM33xx derivates. Other chips may be added if confirmed to work. */ if ((ecc_opt == OMAP_ECC_BCH4_CODE_HW) && - (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0))) { + (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0)) && + (!soc_is_am33xx())) { pr_err("BCH 4-bit mode is not supported on this CPU\n"); return 0; } @@ -110,8 +111,8 @@ static bool __init gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt) return 1; } -int __init gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data, - struct gpmc_timings *gpmc_t) +int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data, + struct gpmc_timings *gpmc_t) { int err = 0; struct device *dev = &gpmc_nand_device.dev; diff --git a/arch/arm/mach-omap2/gpmc-onenand.c b/arch/arm/mach-omap2/gpmc-onenand.c index 94a349e4dc9..fadd87435cd 100644 --- a/arch/arm/mach-omap2/gpmc-onenand.c +++ b/arch/arm/mach-omap2/gpmc-onenand.c @@ -356,7 +356,7 @@ static int gpmc_onenand_setup(void __iomem *onenand_base, int *freq_ptr) return ret; } -void __init gpmc_onenand_init(struct omap_onenand_platform_data *_onenand_data) +void gpmc_onenand_init(struct omap_onenand_platform_data *_onenand_data) { int err; diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index 64bac53da0e..03d771349be 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -25,6 +25,10 @@ #include <linux/module.h> #include <linux/interrupt.h> #include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_mtd.h> +#include <linux/of_device.h> +#include <linux/mtd/nand.h> #include <linux/platform_data/mtd-nand-omap2.h> @@ -34,6 +38,8 @@ #include "common.h" #include "omap_device.h" #include "gpmc.h" +#include "gpmc-nand.h" +#include "gpmc-onenand.h" #define DEVICE_NAME "omap-gpmc" @@ -145,7 +151,8 @@ static unsigned gpmc_irq_start; static struct resource gpmc_mem_root; static struct resource gpmc_cs_mem[GPMC_CS_NUM]; static DEFINE_SPINLOCK(gpmc_mem_lock); -static unsigned int gpmc_cs_map; /* flag for cs which are initialized */ +/* Define chip-selects as reserved by default until probe completes */ +static unsigned int gpmc_cs_map = ((1 << GPMC_CS_NUM) - 1); static struct device *gpmc_dev; static int gpmc_irq; static resource_size_t phys_base, mem_size; @@ -1118,9 +1125,216 @@ int gpmc_calc_timings(struct gpmc_timings *gpmc_t, /* TODO: remove, see function definition */ gpmc_convert_ps_to_ns(gpmc_t); + /* Now the GPMC is initialised, unreserve the chip-selects */ + gpmc_cs_map = 0; + return 0; } +#ifdef CONFIG_OF +static struct of_device_id gpmc_dt_ids[] = { + { .compatible = "ti,omap2420-gpmc" }, + { .compatible = "ti,omap2430-gpmc" }, + { .compatible = "ti,omap3430-gpmc" }, /* omap3430 & omap3630 */ + { .compatible = "ti,omap4430-gpmc" }, /* omap4430 & omap4460 & omap543x */ + { .compatible = "ti,am3352-gpmc" }, /* am335x devices */ + { } +}; +MODULE_DEVICE_TABLE(of, gpmc_dt_ids); + +static void __maybe_unused gpmc_read_timings_dt(struct device_node *np, + struct gpmc_timings *gpmc_t) +{ + u32 val; + + memset(gpmc_t, 0, sizeof(*gpmc_t)); + + /* minimum clock period for syncronous mode */ + if (!of_property_read_u32(np, "gpmc,sync-clk", &val)) + gpmc_t->sync_clk = val; + + /* chip select timtings */ + if (!of_property_read_u32(np, "gpmc,cs-on", &val)) + gpmc_t->cs_on = val; + + if (!of_property_read_u32(np, "gpmc,cs-rd-off", &val)) + gpmc_t->cs_rd_off = val; + + if (!of_property_read_u32(np, "gpmc,cs-wr-off", &val)) + gpmc_t->cs_wr_off = val; + + /* ADV signal timings */ + if (!of_property_read_u32(np, "gpmc,adv-on", &val)) + gpmc_t->adv_on = val; + + if (!of_property_read_u32(np, "gpmc,adv-rd-off", &val)) + gpmc_t->adv_rd_off = val; + + if (!of_property_read_u32(np, "gpmc,adv-wr-off", &val)) + gpmc_t->adv_wr_off = val; + + /* WE signal timings */ + if (!of_property_read_u32(np, "gpmc,we-on", &val)) + gpmc_t->we_on = val; + + if (!of_property_read_u32(np, "gpmc,we-off", &val)) + gpmc_t->we_off = val; + + /* OE signal timings */ + if (!of_property_read_u32(np, "gpmc,oe-on", &val)) + gpmc_t->oe_on = val; + + if (!of_property_read_u32(np, "gpmc,oe-off", &val)) + gpmc_t->oe_off = val; + + /* access and cycle timings */ + if (!of_property_read_u32(np, "gpmc,page-burst-access", &val)) + gpmc_t->page_burst_access = val; + + if (!of_property_read_u32(np, "gpmc,access", &val)) + gpmc_t->access = val; + + if (!of_property_read_u32(np, "gpmc,rd-cycle", &val)) + gpmc_t->rd_cycle = val; + + if (!of_property_read_u32(np, "gpmc,wr-cycle", &val)) + gpmc_t->wr_cycle = val; + + /* only for OMAP3430 */ + if (!of_property_read_u32(np, "gpmc,wr-access", &val)) + gpmc_t->wr_access = val; + + if (!of_property_read_u32(np, "gpmc,wr-data-mux-bus", &val)) + gpmc_t->wr_data_mux_bus = val; +} + +#ifdef CONFIG_MTD_NAND + +static const char * const nand_ecc_opts[] = { + [OMAP_ECC_HAMMING_CODE_DEFAULT] = "sw", + [OMAP_ECC_HAMMING_CODE_HW] = "hw", + [OMAP_ECC_HAMMING_CODE_HW_ROMCODE] = "hw-romcode", + [OMAP_ECC_BCH4_CODE_HW] = "bch4", + [OMAP_ECC_BCH8_CODE_HW] = "bch8", +}; + +static int gpmc_probe_nand_child(struct platform_device *pdev, + struct device_node *child) +{ + u32 val; + const char *s; + struct gpmc_timings gpmc_t; + struct omap_nand_platform_data *gpmc_nand_data; + + if (of_property_read_u32(child, "reg", &val) < 0) { + dev_err(&pdev->dev, "%s has no 'reg' property\n", + child->full_name); + return -ENODEV; + } + + gpmc_nand_data = devm_kzalloc(&pdev->dev, sizeof(*gpmc_nand_data), + GFP_KERNEL); + if (!gpmc_nand_data) + return -ENOMEM; + + gpmc_nand_data->cs = val; + gpmc_nand_data->of_node = child; + + if (!of_property_read_string(child, "ti,nand-ecc-opt", &s)) + for (val = 0; val < ARRAY_SIZE(nand_ecc_opts); val++) + if (!strcasecmp(s, nand_ecc_opts[val])) { + gpmc_nand_data->ecc_opt = val; + break; + } + + val = of_get_nand_bus_width(child); + if (val == 16) + gpmc_nand_data->devsize = NAND_BUSWIDTH_16; + + gpmc_read_timings_dt(child, &gpmc_t); + gpmc_nand_init(gpmc_nand_data, &gpmc_t); + + return 0; +} +#else +static int gpmc_probe_nand_child(struct platform_device *pdev, + struct device_node *child) +{ + return 0; +} +#endif + +#ifdef CONFIG_MTD_ONENAND +static int gpmc_probe_onenand_child(struct platform_device *pdev, + struct device_node *child) +{ + u32 val; + struct omap_onenand_platform_data *gpmc_onenand_data; + + if (of_property_read_u32(child, "reg", &val) < 0) { + dev_err(&pdev->dev, "%s has no 'reg' property\n", + child->full_name); + return -ENODEV; + } + + gpmc_onenand_data = devm_kzalloc(&pdev->dev, sizeof(*gpmc_onenand_data), + GFP_KERNEL); + if (!gpmc_onenand_data) + return -ENOMEM; + + gpmc_onenand_data->cs = val; + gpmc_onenand_data->of_node = child; + gpmc_onenand_data->dma_channel = -1; + + if (!of_property_read_u32(child, "dma-channel", &val)) + gpmc_onenand_data->dma_channel = val; + + gpmc_onenand_init(gpmc_onenand_data); + + return 0; +} +#else +static int gpmc_probe_onenand_child(struct platform_device *pdev, + struct device_node *child) +{ + return 0; +} +#endif + +static int gpmc_probe_dt(struct platform_device *pdev) +{ + int ret; + struct device_node *child; + const struct of_device_id *of_id = + of_match_device(gpmc_dt_ids, &pdev->dev); + + if (!of_id) + return 0; + + for_each_node_by_name(child, "nand") { + ret = gpmc_probe_nand_child(pdev, child); + if (ret < 0) { + of_node_put(child); + return ret; + } + } + + for_each_node_by_name(child, "onenand") { + ret = gpmc_probe_onenand_child(pdev, child); + if (ret < 0) { + of_node_put(child); + return ret; + } + } + return 0; +} +#else +static int gpmc_probe_dt(struct platform_device *pdev) +{ + return 0; +} +#endif + static int gpmc_probe(struct platform_device *pdev) { int rc; @@ -1172,6 +1386,14 @@ static int gpmc_probe(struct platform_device *pdev) if (IS_ERR_VALUE(gpmc_setup_irq())) dev_warn(gpmc_dev, "gpmc_setup_irq failed\n"); + rc = gpmc_probe_dt(pdev); + if (rc < 0) { + clk_disable_unprepare(gpmc_l3_clk); + clk_put(gpmc_l3_clk); + dev_err(gpmc_dev, "failed to probe DT parameters\n"); + return rc; + } + return 0; } @@ -1189,6 +1411,7 @@ static struct platform_driver gpmc_driver = { .driver = { .name = DEVICE_NAME, .owner = THIS_MODULE, + .of_match_table = of_match_ptr(gpmc_dt_ids), }, }; @@ -1212,6 +1435,13 @@ static int __init omap_gpmc_init(void) struct platform_device *pdev; char *oh_name = "gpmc"; + /* + * if the board boots up with a populated DT, do not + * manually add the device from this initcall + */ + if (of_have_populated_dt()) + return -ENODEV; + oh = omap_hwmod_lookup(oh_name); if (!oh) { pr_err("Could not look up %s\n", oh_name); diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c index 12060ae4e8f..a683d17b2ce 100644 --- a/arch/arm/mach-u300/core.c +++ b/arch/arm/mach-u300/core.c @@ -31,6 +31,7 @@ #include <linux/dma-mapping.h> #include <linux/platform_data/clk-u300.h> #include <linux/platform_data/pinctrl-coh901.h> +#include <linux/platform_data/dma-coh901318.h> #include <linux/irqchip/arm-vic.h> #include <asm/types.h> @@ -40,7 +41,6 @@ #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <mach/coh901318.h> #include <mach/hardware.h> #include <mach/syscon.h> #include <mach/irqs.h> @@ -49,7 +49,6 @@ #include "spi.h" #include "i2c.h" #include "u300-gpio.h" -#include "dma_channels.h" /* * Static I/O mappings that are needed for booting the U300 platforms. The @@ -327,1089 +326,6 @@ static struct resource dma_resource[] = { } }; -/* points out all dma slave channels. - * Syntax is [A1, B1, A2, B2, .... ,-1,-1] - * Select all channels from A to B, end of list is marked with -1,-1 - */ -static int dma_slave_channels[] = { - U300_DMA_MSL_TX_0, U300_DMA_SPI_RX, - U300_DMA_UART1_TX, U300_DMA_UART1_RX, -1, -1}; - -/* points out all dma memcpy channels. */ -static int dma_memcpy_channels[] = { - U300_DMA_GENERAL_PURPOSE_0, U300_DMA_GENERAL_PURPOSE_8, -1, -1}; - -/** register dma for memory access - * - * active 1 means dma intends to access memory - * 0 means dma wont access memory - */ -static void coh901318_access_memory_state(struct device *dev, bool active) -{ -} - -#define flags_memcpy_config (COH901318_CX_CFG_CH_DISABLE | \ - COH901318_CX_CFG_RM_MEMORY_TO_MEMORY | \ - COH901318_CX_CFG_LCR_DISABLE | \ - COH901318_CX_CFG_TC_IRQ_ENABLE | \ - COH901318_CX_CFG_BE_IRQ_ENABLE) -#define flags_memcpy_lli_chained (COH901318_CX_CTRL_TC_ENABLE | \ - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \ - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \ - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \ - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \ - COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \ - COH901318_CX_CTRL_MASTER_MODE_M1RW | \ - COH901318_CX_CTRL_TCP_DISABLE | \ - COH901318_CX_CTRL_TC_IRQ_DISABLE | \ - COH901318_CX_CTRL_HSP_DISABLE | \ - COH901318_CX_CTRL_HSS_DISABLE | \ - COH901318_CX_CTRL_DDMA_LEGACY | \ - COH901318_CX_CTRL_PRDD_SOURCE) -#define flags_memcpy_lli (COH901318_CX_CTRL_TC_ENABLE | \ - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \ - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \ - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \ - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \ - COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \ - COH901318_CX_CTRL_MASTER_MODE_M1RW | \ - COH901318_CX_CTRL_TCP_DISABLE | \ - COH901318_CX_CTRL_TC_IRQ_DISABLE | \ - COH901318_CX_CTRL_HSP_DISABLE | \ - COH901318_CX_CTRL_HSS_DISABLE | \ - COH901318_CX_CTRL_DDMA_LEGACY | \ - COH901318_CX_CTRL_PRDD_SOURCE) -#define flags_memcpy_lli_last (COH901318_CX_CTRL_TC_ENABLE | \ - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | \ - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | \ - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | \ - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | \ - COH901318_CX_CTRL_DST_ADDR_INC_ENABLE | \ - COH901318_CX_CTRL_MASTER_MODE_M1RW | \ - COH901318_CX_CTRL_TCP_DISABLE | \ - COH901318_CX_CTRL_TC_IRQ_ENABLE | \ - COH901318_CX_CTRL_HSP_DISABLE | \ - COH901318_CX_CTRL_HSS_DISABLE | \ - COH901318_CX_CTRL_DDMA_LEGACY | \ - COH901318_CX_CTRL_PRDD_SOURCE) - -const struct coh_dma_channel chan_config[U300_DMA_CHANNELS] = { - { - .number = U300_DMA_MSL_TX_0, - .name = "MSL TX 0", - .priority_high = 0, - .dev_addr = U300_MSL_BASE + 0 * 0x40 + 0x20, - }, - { - .number = U300_DMA_MSL_TX_1, - .name = "MSL TX 1", - .priority_high = 0, - .dev_addr = U300_MSL_BASE + 1 * 0x40 + 0x20, - .param.config = COH901318_CX_CFG_CH_DISABLE | - COH901318_CX_CFG_LCR_DISABLE | - COH901318_CX_CFG_TC_IRQ_ENABLE | - COH901318_CX_CFG_BE_IRQ_ENABLE, - .param.ctrl_lli_chained = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_DISABLE | - COH901318_CX_CTRL_TC_IRQ_DISABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - .param.ctrl_lli = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_ENABLE | - COH901318_CX_CTRL_TC_IRQ_DISABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - .param.ctrl_lli_last = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_ENABLE | - COH901318_CX_CTRL_TC_IRQ_ENABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - }, - { - .number = U300_DMA_MSL_TX_2, - .name = "MSL TX 2", - .priority_high = 0, - .dev_addr = U300_MSL_BASE + 2 * 0x40 + 0x20, - .param.config = COH901318_CX_CFG_CH_DISABLE | - COH901318_CX_CFG_LCR_DISABLE | - COH901318_CX_CFG_TC_IRQ_ENABLE | - COH901318_CX_CFG_BE_IRQ_ENABLE, - .param.ctrl_lli_chained = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_DISABLE | - COH901318_CX_CTRL_TC_IRQ_DISABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - .param.ctrl_lli = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_ENABLE | - COH901318_CX_CTRL_TC_IRQ_DISABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - .param.ctrl_lli_last = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_ENABLE | - COH901318_CX_CTRL_TC_IRQ_ENABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - .desc_nbr_max = 10, - }, - { - .number = U300_DMA_MSL_TX_3, - .name = "MSL TX 3", - .priority_high = 0, - .dev_addr = U300_MSL_BASE + 3 * 0x40 + 0x20, - .param.config = COH901318_CX_CFG_CH_DISABLE | - COH901318_CX_CFG_LCR_DISABLE | - COH901318_CX_CFG_TC_IRQ_ENABLE | - COH901318_CX_CFG_BE_IRQ_ENABLE, - .param.ctrl_lli_chained = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_DISABLE | - COH901318_CX_CTRL_TC_IRQ_DISABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - .param.ctrl_lli = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_ENABLE | - COH901318_CX_CTRL_TC_IRQ_DISABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - .param.ctrl_lli_last = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_ENABLE | - COH901318_CX_CTRL_TC_IRQ_ENABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - }, - { - .number = U300_DMA_MSL_TX_4, - .name = "MSL TX 4", - .priority_high = 0, - .dev_addr = U300_MSL_BASE + 4 * 0x40 + 0x20, - .param.config = COH901318_CX_CFG_CH_DISABLE | - COH901318_CX_CFG_LCR_DISABLE | - COH901318_CX_CFG_TC_IRQ_ENABLE | - COH901318_CX_CFG_BE_IRQ_ENABLE, - .param.ctrl_lli_chained = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_DISABLE | - COH901318_CX_CTRL_TC_IRQ_DISABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - .param.ctrl_lli = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_ENABLE | - COH901318_CX_CTRL_TC_IRQ_DISABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - .param.ctrl_lli_last = 0 | - COH901318_CX_CTRL_TC_ENABLE | - COH901318_CX_CTRL_BURST_COUNT_32_BYTES | - COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE | - COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS | - COH901318_CX_CTRL_DST_ADDR_INC_DISABLE | - COH901318_CX_CTRL_MASTER_MODE_M1R_M2W | - COH901318_CX_CTRL_TCP_ENABLE | - COH901318_CX_CTRL_TC_IRQ_ENABLE | - COH901318_CX_CTRL_HSP_ENABLE | - COH901318_CX_CTRL_HSS_DISABLE | - COH901318_CX_CTRL_DDMA_LEGACY | - COH901318_CX_CTRL_PRDD_SOURCE, - }, - { - .number = U300_DMA_MSL_TX_5, - .name = "MSL TX 5", - .priority_high = 0, - .dev_addr = U300_MSL_BASE + 5 * 0x40 + 0x20, - }, - { - .number = U300_DMA_MSL_TX_6, - .name = "MSL TX 6", - .priority_high = 0, - .dev_addr = U300_MSL_BASE + 6 * 0x40 + 0x20, - }, - { - .number = U300_DMA_MSL_RX_0, - .name = "MSL RX 0", - .priority_high = 0, - .dev_addr = U300_MSL_BASE + 0 * 0x40 + 0x220, - }, - { - .number = U300_DMA_MSL_RX_1, - .name = "MSL RX 1", - .priority_high = 0, - .dev_addr = U300_MSL_BASE + 1 * 0x40 + 0x220, - .param.config = COH901318_CX_CFG_CH_DISABLE | - COH901318_CX_CFG_LCR_DISABLE | - COH901318_CX_CFG_TC_IRQ_ENABLE | - COH901318_CX_CFG_BE_IRQ_ENABLE, - |