diff options
| -rw-r--r-- | Documentation/sound/alsa/HD-Audio-Controls.txt | 100 |
1 files changed, 100 insertions, 0 deletions
diff --git a/Documentation/sound/alsa/HD-Audio-Controls.txt b/Documentation/sound/alsa/HD-Audio-Controls.txt new file mode 100644 index 00000000000..1482035243e --- /dev/null +++ b/Documentation/sound/alsa/HD-Audio-Controls.txt @@ -0,0 +1,100 @@ +This file explains the codec-specific mixer controls. + +Realtek codecs +-------------- + +* Channel Mode + This is an enum control to change the surround-channel setup, + appears only when the surround channels are available. + It gives the number of channels to be used, "2ch", "4ch", "6ch", + and "8ch". According to the configuration, this also controls the + jack-retasking of multi-I/O jacks. + +* Auto-Mute Mode + This is an enum control to change the auto-mute behavior of the + headphone and line-out jacks. If built-in speakers and headphone + and/or line-out jacks are available on a machine, this controls + appears. + When there are only either headphones or line-out jacks, it gives + "Disabled" and "Enabled" state. When enabled, the speaker is muted + automatically when a jack is plugged. + + When both headphone and line-out jacks are present, it gives + "Disabled", "Speaker Only" and "Line-Out+Speaker". When + speaker-only is chosen, plugging into a headphone or a line-out jack + mutes the speakers, but not line-outs. When line-out+speaker is + selected, plugging to a headphone jack mutes both speakers and + line-outs. + + +IDT/Sigmatel codecs +------------------- + +* Analog Loopback + This control enables/disables the analog-loopback circuit. This + appears only when "loopback" is set to true in a codec hint + (see HD-Audio.txt). Note that on some codecs the analog-loopback + and the normal PCM playback are exclusive, i.e. when this is on, you + won't hear any PCM stream. + +* Swap Center/LFE + Swaps the center and LFE channel order. Normally, the left + corresponds to the center and the right to the LFE. When this is + ON, the left to the LFE and the right to the center. + +* Headphone as Line Out + When this control is ON, treat the headphone jacks as line-out + jacks. That is, the headphone won't auto-mute the other line-outs, + and no HP-amp is set to the pins. + +* Mic Jack Mode, Line Jack Mode, etc + These enum controls the direction and the bias of the input jack + pins. Depending on the jack type, it can set as "Mic In" and "Line + In", for determining the input bias, or it can be set to "Line Out" + when the pin is a multi-I/O jack for surround channels. + + +VIA codecs +---------- + +* Smart 5.1 + An enum control to re-task the multi-I/O jacks for surround outputs. + When it's ON, the corresponding input jacks (usually a line-in and a + mic-in) are switched as the surround and the CLFE output jacks. + +* Independent HP + When this enum control is enabled, the headphone output is routed + from an individual stream (the third PCM such as hw:0,2) instead of + the primary stream. In the case the headphone DAC is shared with a + side or a CLFE-channel DAC, the DAC is switched to the headphone + automatically. + +* Loopback Mixing + An enum control to determine whether the analog-loopback route is + enabled or not. When it's enabled, the analog-loopback is mixed to + the front-channel. Also, the same route is used for the headphone + and speaker outputs. As a side-effect, when this mode is set, the + individual volume controls will be no longer available for + headphones and speakers because there is only one DAC connected to a + mixer widget. + +* Dynamic Power-Control + This control determines whether the dynamic power-control per jack + detection is enabled or not. When enabled, the widgets power state + (D0/D3) are changed dynamically depending on the jack plugging + state for saving power consumptions. However, if your system + doesn't provide a proper jack-detection, this won't work; in such a + case, turn this control OFF. + +* Jack Detect + This control is provided only for VT1708 codec which gives no proper + unsolicited event per jack plug. When this is on, the driver polls + the jack detection so that the headphone auto-mute can work, while + turning this off would reduce the power consumption. + + +Conexant codecs +--------------- + +* Auto-Mute Mode + See Reatek codecs. |