diff options
| -rw-r--r-- | drivers/scsi/lpfc/lpfc_init.c | 50 |
1 files changed, 27 insertions, 23 deletions
diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c index feba3be90cb..56421c714bf 100644 --- a/drivers/scsi/lpfc/lpfc_init.c +++ b/drivers/scsi/lpfc/lpfc_init.c @@ -7764,21 +7764,23 @@ lpfc_pci_resume_one_s3(struct pci_dev *pdev) * @phba: pointer to lpfc hba data structure. * * This routine is called to prepare the SLI3 device for PCI slot recover. It - * aborts and stops all the on-going I/Os on the pci device. + * aborts all the outstanding SCSI I/Os to the pci device. **/ static void lpfc_sli_prep_dev_for_recover(struct lpfc_hba *phba) { + struct lpfc_sli *psli = &phba->sli; + struct lpfc_sli_ring *pring; + lpfc_printf_log(phba, KERN_ERR, LOG_INIT, "2723 PCI channel I/O abort preparing for recovery\n"); - /* Prepare for bringing HBA offline */ - lpfc_offline_prep(phba); - /* Clear sli active flag to prevent sysfs access to HBA */ - spin_lock_irq(&phba->hbalock); - phba->sli.sli_flag &= ~LPFC_SLI_ACTIVE; - spin_unlock_irq(&phba->hbalock); - /* Stop and flush all I/Os and bring HBA offline */ - lpfc_offline(phba); + + /* + * There may be errored I/Os through HBA, abort all I/Os on txcmplq + * and let the SCSI mid-layer to retry them to recover. + */ + pring = &psli->ring[psli->fcp_ring]; + lpfc_sli_abort_iocb_ring(phba, pring); } /** @@ -7792,21 +7794,20 @@ lpfc_sli_prep_dev_for_recover(struct lpfc_hba *phba) static void lpfc_sli_prep_dev_for_reset(struct lpfc_hba *phba) { - struct lpfc_sli *psli = &phba->sli; - struct lpfc_sli_ring *pring; - lpfc_printf_log(phba, KERN_ERR, LOG_INIT, "2710 PCI channel disable preparing for reset\n"); + + /* Block all SCSI devices' I/Os on the host */ + lpfc_scsi_dev_block(phba); + + /* stop all timers */ + lpfc_stop_hba_timers(phba); + /* Disable interrupt and pci device */ lpfc_sli_disable_intr(phba); pci_disable_device(phba->pcidev); - /* - * There may be I/Os dropped by the firmware. - * Error iocb (I/O) on txcmplq and let the SCSI layer - * retry it after re-establishing link. - */ - pring = &psli->ring[psli->fcp_ring]; - lpfc_sli_abort_iocb_ring(phba, pring); + /* Flush all driver's outstanding SCSI I/Os as we are to reset */ + lpfc_sli_flush_fcp_rings(phba); } /** @@ -7822,6 +7823,12 @@ lpfc_prep_dev_for_perm_failure(struct lpfc_hba *phba) { lpfc_printf_log(phba, KERN_ERR, LOG_INIT, "2711 PCI channel permanent disable for failure\n"); + /* Block all SCSI devices' I/Os on the host */ + lpfc_scsi_dev_block(phba); + + /* stop all timers */ + lpfc_stop_hba_timers(phba); + /* Clean up all driver's outstanding SCSI I/Os */ lpfc_sli_flush_fcp_rings(phba); } @@ -7850,9 +7857,6 @@ lpfc_io_error_detected_s3(struct pci_dev *pdev, pci_channel_state_t state) struct Scsi_Host *shost = pci_get_drvdata(pdev); struct lpfc_hba *phba = ((struct lpfc_vport *)shost->hostdata)->phba; - /* Block all SCSI devices' I/Os on the host */ - lpfc_scsi_dev_block(phba); - switch (state) { case pci_channel_io_normal: /* Non-fatal error, prepare for recovery */ @@ -7959,7 +7963,7 @@ lpfc_io_resume_s3(struct pci_dev *pdev) struct Scsi_Host *shost = pci_get_drvdata(pdev); struct lpfc_hba *phba = ((struct lpfc_vport *)shost->hostdata)->phba; - /* Bring the device online */ + /* Bring device online, it will be no-op for non-fatal error resume */ lpfc_online(phba); /* Clean up Advanced Error Reporting (AER) if needed */ |