diff options
| -rw-r--r-- | arch/mips/au1000/pb1100/board_setup.c | 93 |
1 files changed, 48 insertions, 45 deletions
diff --git a/arch/mips/au1000/pb1100/board_setup.c b/arch/mips/au1000/pb1100/board_setup.c index 2d1533f116c..6bc1f8e1b60 100644 --- a/arch/mips/au1000/pb1100/board_setup.c +++ b/arch/mips/au1000/pb1100/board_setup.c @@ -47,8 +47,7 @@ void board_reset (void) void __init board_setup(void) { - u32 pin_func; - u32 sys_freqctrl, sys_clksrc; + volatile void __iomem * base = (volatile void __iomem *) 0xac000000UL; // set AUX clock to 12MHz * 8 = 96 MHz au_writel(8, SYS_AUXPLL); @@ -56,58 +55,62 @@ void __init board_setup(void) udelay(100); #ifdef CONFIG_USB_OHCI - // configure pins GPIO[14:9] as GPIO - pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x80); - - /* zero and disable FREQ2 */ - sys_freqctrl = au_readl(SYS_FREQCTRL0); - sys_freqctrl &= ~0xFFF00000; - au_writel(sys_freqctrl, SYS_FREQCTRL0); - - /* zero and disable USBH/USBD/IrDA clock */ - sys_clksrc = au_readl(SYS_CLKSRC); - sys_clksrc &= ~0x0000001F; - au_writel(sys_clksrc, SYS_CLKSRC); - - sys_freqctrl = au_readl(SYS_FREQCTRL0); - sys_freqctrl &= ~0xFFF00000; - - sys_clksrc = au_readl(SYS_CLKSRC); - sys_clksrc &= ~0x0000001F; - - // FREQ2 = aux/2 = 48 MHz - sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20)); - au_writel(sys_freqctrl, SYS_FREQCTRL0); - - /* - * Route 48MHz FREQ2 into USBH/USBD/IrDA - */ - sys_clksrc |= ((4<<2) | (0<<1) | 0 ); - au_writel(sys_clksrc, SYS_CLKSRC); - - /* setup the static bus controller */ - au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */ - au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */ - au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */ - - // get USB Functionality pin state (device vs host drive pins) - pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000); - // 2nd USB port is USB host - pin_func |= 0x8000; - au_writel(pin_func, SYS_PINFUNC); + { + u32 pin_func, sys_freqctrl, sys_clksrc; + + // configure pins GPIO[14:9] as GPIO + pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x80); + + /* zero and disable FREQ2 */ + sys_freqctrl = au_readl(SYS_FREQCTRL0); + sys_freqctrl &= ~0xFFF00000; + au_writel(sys_freqctrl, SYS_FREQCTRL0); + + /* zero and disable USBH/USBD/IrDA clock */ + sys_clksrc = au_readl(SYS_CLKSRC); + sys_clksrc &= ~0x0000001F; + au_writel(sys_clksrc, SYS_CLKSRC); + + sys_freqctrl = au_readl(SYS_FREQCTRL0); + sys_freqctrl &= ~0xFFF00000; + + sys_clksrc = au_readl(SYS_CLKSRC); + sys_clksrc &= ~0x0000001F; + + // FREQ2 = aux/2 = 48 MHz + sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20)); + au_writel(sys_freqctrl, SYS_FREQCTRL0); + + /* + * Route 48MHz FREQ2 into USBH/USBD/IrDA + */ + sys_clksrc |= ((4<<2) | (0<<1) | 0 ); + au_writel(sys_clksrc, SYS_CLKSRC); + + /* setup the static bus controller */ + au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */ + au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */ + au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */ + + // get USB Functionality pin state (device vs host drive pins) + pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000); + // 2nd USB port is USB host + pin_func |= 0x8000; + au_writel(pin_func, SYS_PINFUNC); + } #endif // defined (CONFIG_USB_OHCI) /* Enable sys bus clock divider when IDLE state or no bus activity. */ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL); // Enable the RTC if not already enabled - if (!(readb(0xac000028) & 0x20)) { - writeb(readb(0xac000028) | 0x20, 0xac000028); + if (!(readb(base + 0x28) & 0x20)) { + writeb(readb(base + 0x28) | 0x20, base + 0x28); au_sync(); } // Put the clock in BCD mode - if (readb(0xac00002C) & 0x4) { /* reg B */ - writeb(readb(0xac00002c) & ~0x4, 0xac00002c); + if (readb(base + 0x2C) & 0x4) { /* reg B */ + writeb(readb(base + 0x2c) & ~0x4, base + 0x2c); au_sync(); } } |