diff options
| -rw-r--r-- | arch/arm/mach-at91/Kconfig | 6 | ||||
| -rw-r--r-- | arch/arm/mach-at91/Makefile | 1 | ||||
| -rw-r--r-- | arch/arm/mach-at91/board-foxg20.c | 274 |
3 files changed, 281 insertions, 0 deletions
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index c015b684b4f..06fb66d5320 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -362,6 +362,12 @@ config MACH_CPU9G20 Select this if you are using a Eukrea Electromatique's CPU9G20 Board <http://www.eukrea.com/> +config MACH_ACMENETUSFOXG20 + bool "Acme Systems srl FOX Board G20" + help + Select this if you are using Acme Systems + FOX Board G20 <http://www.acmesystems.it> + config MACH_PORTUXG20 bool "taskit PortuxG20" help diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index d13add71f72..5ef548ee58b 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -63,6 +63,7 @@ obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o # AT91SAM9G20 board-specific support obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o obj-$(CONFIG_MACH_CPU9G20) += board-cpu9krea.o +obj-$(CONFIG_MACH_ACMENETUSFOXG20) += board-foxg20.o obj-$(CONFIG_MACH_STAMP9G20) += board-stamp9g20.o obj-$(CONFIG_MACH_PORTUXG20) += board-stamp9g20.o obj-$(CONFIG_MACH_PCONTROL_G20) += board-pcontrol-g20.o board-stamp9g20.o diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c new file mode 100644 index 00000000000..dfc7dfe738e --- /dev/null +++ b/arch/arm/mach-at91/board-foxg20.c @@ -0,0 +1,274 @@ +/* + * Copyright (C) 2005 SAN People + * Copyright (C) 2008 Atmel + * Copyright (C) 2010 Lee McLoughlin - lee@lmmrtech.com + * Copyright (C) 2010 Sergio Tanzilli - tanzilli@acmesystems.it + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/spi/at73c213.h> +#include <linux/gpio.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> +#include <linux/clk.h> +#include <linux/w1-gpio.h> + +#include <mach/hardware.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <mach/board.h> +#include <mach/at91sam9_smc.h> + +#include "sam9_smc.h" +#include "generic.h" + +/* + * The FOX Board G20 hardware comes as the "Netus G20" board with + * just the cpu, ram, dataflash and two header connectors. + * This is plugged into the FOX Board which provides the ethernet, + * usb, rtc, leds, switch, ... + * + * For more info visit: http://www.acmesystems.it/foxg20 + */ + + +static void __init foxg20_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91sam9260_initialize(18432000); + + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, + ATMEL_UART_CTS + | ATMEL_UART_RTS + | ATMEL_UART_DTR + | ATMEL_UART_DSR + | ATMEL_UART_DCD + | ATMEL_UART_RI); + + /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US1, 2, + ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART2 on ttyS3. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US2, 3, 0); + + /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */ + at91_register_uart(AT91SAM9260_ID_US3, 4, + ATMEL_UART_CTS + | ATMEL_UART_RTS); + + /* USART4 on ttyS5. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US4, 5, 0); + + /* USART5 on ttyS6. (Rx & Tx only) */ + at91_register_uart(AT91SAM9260_ID_US5, 6, 0); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); + + /* Set the internal pull-up resistor on DRXD */ + at91_set_A_periph(AT91_PIN_PB14, 1); + +} + +static void __init foxg20_init_irq(void) +{ + at91sam9260_init_interrupts(NULL); +} + + +/* + * USB Host port + */ +static struct at91_usbh_data __initdata foxg20_usbh_data = { + .ports = 2, +}; + +/* + * USB Device port + */ +static struct at91_udc_data __initdata foxg20_udc_data = { + .vbus_pin = AT91_PIN_PC6, + .pullup_pin = 0, /* pull-up driven by UDC */ +}; + + +/* + * SPI devices. + */ +static struct spi_board_info foxg20_spi_devices[] = { +#if !defined(CONFIG_MMC_AT91) + { + .modalias = "mtd_dataflash", + .chip_select = 1, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +#endif +}; + + +/* + * MACB Ethernet device + */ +static struct at91_eth_data __initdata foxg20_macb_data = { + .phy_irq_pin = AT91_PIN_PA7, + .is_rmii = 1, +}; + +/* + * MCI (SD/MMC) + * det_pin, wp_pin and vcc_pin are not connected + */ +static struct at91_mmc_data __initdata foxg20_mmc_data = { + .slot_b = 1, + .wire4 = 1, +}; + + +/* + * LEDs + */ +static struct gpio_led foxg20_leds[] = { + { /* user led, red */ + .name = "user_led", + .gpio = AT91_PIN_PC7, + .active_low = 0, + .default_trigger = "heartbeat", + }, +}; + + +/* + * GPIO Buttons + */ +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +static struct gpio_keys_button foxg20_buttons[] = { + { + .gpio = AT91_PIN_PC4, + .code = BTN_1, + .desc = "Button 1", + .active_low = 1, + .wakeup = 1, + }, +}; + +static struct gpio_keys_platform_data foxg20_button_data = { + .buttons = foxg20_buttons, + .nbuttons = ARRAY_SIZE(foxg20_buttons), +}; + +static struct platform_device foxg20_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &foxg20_button_data, + } +}; + +static void __init foxg20_add_device_buttons(void) +{ + at91_set_gpio_input(AT91_PIN_PC4, 1); /* btn1 */ + at91_set_deglitch(AT91_PIN_PC4, 1); + + platform_device_register(&foxg20_button_device); +} +#else +static void __init foxg20_add_device_buttons(void) {} +#endif + + +#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE) +static struct w1_gpio_platform_data w1_gpio_pdata = { + /* If you choose to use a pin other than PB16 it needs to be 3.3V */ + .pin = AT91_PIN_PB16, + .is_open_drain = 1, +}; + +static struct platform_device w1_device = { + .name = "w1-gpio", + .id = -1, + .dev.platform_data = &w1_gpio_pdata, +}; + +static void __init at91_add_device_w1(void) +{ + at91_set_GPIO_periph(w1_gpio_pdata.pin, 1); + at91_set_multi_drive(w1_gpio_pdata.pin, 1); + platform_device_register(&w1_device); +} + +#endif + + +static struct i2c_board_info __initdata foxg20_i2c_devices[] = { + { + I2C_BOARD_INFO("24c512", 0x50), + }, +}; + + +static void __init foxg20_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* USB Host */ + at91_add_device_usbh(&foxg20_usbh_data); + /* USB Device */ + at91_add_device_udc(&foxg20_udc_data); + /* SPI */ + at91_add_device_spi(foxg20_spi_devices, ARRAY_SIZE(foxg20_spi_devices)); + /* Ethernet */ + at91_add_device_eth(&foxg20_macb_data); + /* MMC */ + at91_add_device_mmc(0, &foxg20_mmc_data); + /* I2C */ + at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices)); + /* LEDs */ + at91_gpio_leds(foxg20_leds, ARRAY_SIZE(foxg20_leds)); + /* Push Buttons */ + foxg20_add_device_buttons(); +#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE) + at91_add_device_w1(); +#endif +} + +MACHINE_START(ACMENETUSFOXG20, "Acme Systems srl FOX Board G20") + /* Maintainer: Sergio Tanzilli */ + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = foxg20_map_io, + .init_irq = foxg20_init_irq, + .init_machine = foxg20_board_init, +MACHINE_END |