diff options
93 files changed, 1336 insertions, 2106 deletions
diff --git a/Documentation/ide/ide.txt b/Documentation/ide/ide.txt index 818676aad45..486c699f4ae 100644 --- a/Documentation/ide/ide.txt +++ b/Documentation/ide/ide.txt @@ -71,29 +71,6 @@ This driver automatically probes for most IDE interfaces (including all PCI ones), for the drives/geometries attached to those interfaces, and for the IRQ lines being used by the interfaces (normally 14, 15 for ide0/ide1). -For special cases, interfaces may be specified using kernel "command line" -options. For example, - - ide3=0x168,0x36e,10 /* ioports 0x168-0x16f,0x36e, irq 10 */ - -Normally the irq number need not be specified, as ide.c will probe for it: - - ide3=0x168,0x36e /* ioports 0x168-0x16f,0x36e */ - -The standard port, and irq values are these: - - ide0=0x1f0,0x3f6,14 - ide1=0x170,0x376,15 - ide2=0x1e8,0x3ee,11 - ide3=0x168,0x36e,10 - -Note that the first parameter reserves 8 contiguous ioports, whereas the -second value denotes a single ioport. If in doubt, do a 'cat /proc/ioports'. - -In all probability the device uses these ports and IRQs if it is attached -to the appropriate ide channel. Pass the parameter for the correct ide -channel to the kernel, as explained above. - Any number of interfaces may share a single IRQ if necessary, at a slight performance penalty, whether on separate cards or a single VLB card. The IDE driver automatically detects and handles this. However, this may @@ -184,13 +161,6 @@ provided it is mounted with the default block size of 1024 (as above). Please pass on any feedback on any of this stuff to the maintainer, whose address can be found in linux/MAINTAINERS. -Note that if BOTH hd.c and ide.c are configured into the kernel, -hd.c will normally be allowed to control the primary IDE interface. -This is useful for older hardware that may be incompatible with ide.c, -and still allows newer hardware to run on the 2nd/3rd/4th IDE ports -under control of ide.c. To have ide.c also "take over" the primary -IDE port in this situation, use the "command line" parameter: ide0=0x1f0 - The IDE driver is modularized. The high level disk/CD-ROM/tape/floppy drivers can always be compiled as loadable modules, the chipset drivers can only be compiled into the kernel, and the core code (ide.c) can be @@ -206,7 +176,7 @@ When ide.c is used as a module, you can pass command line parameters to the driver using the "options=" keyword to insmod, while replacing any ',' with ';'. For example: - insmod ide.o options="ide0=serialize ide1=serialize ide2=0x1e8;0x3ee;11" + insmod ide.o options="hda=nodma hdb=nodma" ================================================================================ @@ -247,21 +217,11 @@ Summary of ide driver parameters for kernel command line As for VLB, it is safest to not specify it. Bigger values are safer than smaller ones. - "idex=base" : probe for an interface at the addr specified, - where "base" is usually 0x1f0 or 0x170 - and "ctl" is assumed to be "base"+0x206 - - "idex=base,ctl" : specify both base and ctl - - "idex=base,ctl,irq" : specify base, ctl, and irq number - "idex=serialize" : do not overlap operations on idex. Please note that you will have to specify this option for both the respective primary and secondary channel to take effect. - "idex=four" : four drives on idex and ide(x^1) share same ports - "idex=reset" : reset interface after probe "idex=ata66" : informs the interface that it has an 80c cable @@ -269,8 +229,6 @@ Summary of ide driver parameters for kernel command line ability to bit test for detection is currently unknown. - "ide=reverse" : formerly called to pci sub-system, but now local. - "ide=doubler" : probe/support IDE doublers on Amiga There may be more options than shown -- use the source, Luke! @@ -290,6 +248,9 @@ Also for legacy CMD640 host driver (cmd640) you need to use "probe_vlb" kernel paremeter to enable probing for VLB version of the chipset (PCI ones are detected automatically). +You also need to use "probe" kernel parameter for ide-4drives driver +(support for IDE generic chipset with four drives on one port). + ================================================================================ Some Terminology diff --git a/Documentation/ide/warm-plug-howto.txt b/Documentation/ide/warm-plug-howto.txt new file mode 100644 index 00000000000..d5885468b07 --- /dev/null +++ b/Documentation/ide/warm-plug-howto.txt @@ -0,0 +1,13 @@ + +IDE warm-plug HOWTO +=================== + +To warm-plug devices on a port 'idex': + +# echo -n "1" > /sys/class/ide_port/idex/delete_devices + +unplug old device(s) and plug new device(s) + +# echo -n "1" > /sys/class/ide_port/idex/scan + +done diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index c867f506366..cd6f464b919 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -763,11 +763,11 @@ and is between 256 and 4096 characters. It is defined in the file Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]] ide= [HW] (E)IDE subsystem - Format: ide=nodma or ide=doubler or ide=reverse + Format: ide=nodma or ide=doubler See Documentation/ide/ide.txt. ide?= [HW] (E)IDE subsystem - Format: ide?=noprobe or chipset specific parameters. + Format: ide?=ata66 or chipset specific parameters. See Documentation/ide/ide.txt. idebus= [HW] (E)IDE subsystem - VLB/PCI bus speed diff --git a/arch/powerpc/kernel/setup_32.c b/arch/powerpc/kernel/setup_32.c index cd870a823d1..06d918d94dd 100644 --- a/arch/powerpc/kernel/setup_32.c +++ b/arch/powerpc/kernel/setup_32.c @@ -10,9 +10,6 @@ #include <linux/reboot.h> #include <linux/delay.h> #include <linux/initrd.h> -#if defined(CONFIG_IDE) || defined(CONFIG_IDE_MODULE) -#include <linux/ide.h> -#endif #include <linux/tty.h> #include <linux/bootmem.h> #include <linux/seq_file.h> @@ -51,11 +48,6 @@ extern void bootx_init(unsigned long r4, unsigned long phys); -#if defined(CONFIG_BLK_DEV_IDE) || defined(CONFIG_BLK_DEV_IDE_MODULE) -struct ide_machdep_calls ppc_ide_md; -EXPORT_SYMBOL(ppc_ide_md); -#endif - int boot_cpuid; EXPORT_SYMBOL_GPL(boot_cpuid); int boot_cpuid_phys; diff --git a/arch/powerpc/platforms/powermac/pci.c b/arch/powerpc/platforms/powermac/pci.c index 1c58db9d42c..bcf50d7056e 100644 --- a/arch/powerpc/platforms/powermac/pci.c +++ b/arch/powerpc/platforms/powermac/pci.c @@ -1144,28 +1144,6 @@ void __init pmac_pcibios_after_init(void) { struct device_node* nd; -#ifdef CONFIG_BLK_DEV_IDE - struct pci_dev *dev = NULL; - - /* OF fails to initialize IDE controllers on macs - * (and maybe other machines) - * - * Ideally, this should be moved to the IDE layer, but we need - * to check specifically with Andre Hedrick how to do it cleanly - * since the common IDE code seem to care about the fact that the - * BIOS may have disabled a controller. - * - * -- BenH - */ - for_each_pci_dev(dev) { - if ((dev->class >> 16) != PCI_BASE_CLASS_STORAGE) - continue; - if (pci_enable_device(dev)) - printk(KERN_WARNING - "pci: Failed to enable %s\n", pci_name(dev)); - } -#endif /* CONFIG_BLK_DEV_IDE */ - for_each_node_by_name(nd, "firewire") { if (nd->parent && (of_device_is_compatible(nd, "pci106b,18") || of_device_is_compatible(nd, "pci106b,30") || diff --git a/arch/powerpc/platforms/powermac/pmac.h b/arch/powerpc/platforms/powermac/pmac.h index b3abaaf61eb..3362e781b6a 100644 --- a/arch/powerpc/platforms/powermac/pmac.h +++ b/arch/powerpc/platforms/powermac/pmac.h @@ -2,7 +2,6 @@ #define __PMAC_H__ #include <linux/pci.h> -#include <linux/ide.h> #include <linux/irq.h> /* @@ -35,10 +34,6 @@ extern void pmac_check_ht_link(void); extern void pmac_setup_smp(void); -extern unsigned long pmac_ide_get_base(int index); -extern void pmac_ide_init_hwif_ports(hw_regs_t *hw, - unsigned long data_port, unsigned long ctrl_port, int *irq); - extern int pmac_nvram_init(void); extern void pmac_pic_init(void); diff --git a/arch/powerpc/platforms/powermac/setup.c b/arch/powerpc/platforms/powermac/setup.c index 36ff1b6b7fa..2693fc371ea 100644 --- a/arch/powerpc/platforms/powermac/setup.c +++ b/arch/powerpc/platforms/powermac/setup.c @@ -574,14 +574,6 @@ static int __init pmac_probe(void) ISA_DMA_THRESHOLD = ~0L; DMA_MODE_READ = 1; DMA_MODE_WRITE = 2; - -#if defined(CONFIG_BLK_DEV_IDE) || defined(CONFIG_BLK_DEV_IDE_MODULE) -#ifdef CONFIG_BLK_DEV_IDE_PMAC - ppc_ide_md.ide_init_hwif = pmac_ide_init_hwif_ports; - ppc_ide_md.default_io_base = pmac_ide_get_base; -#endif /* CONFIG_BLK_DEV_IDE_PMAC */ -#endif /* defined(CONFIG_BLK_DEV_IDE) || defined(CONFIG_BLK_DEV_IDE_MODULE) */ - #endif /* CONFIG_PPC32 */ #ifdef CONFIG_PMAC_SMU diff --git a/arch/ppc/configs/sandpoint_defconfig b/arch/ppc/configs/sandpoint_defconfig index fb493a67c60..9525e34138f 100644 --- a/arch/ppc/configs/sandpoint_defconfig +++ b/arch/ppc/configs/sandpoint_defconfig @@ -189,7 +189,7 @@ CONFIG_IDE_TASKFILE_IO=y # # IDE chipset support/bugfixes # -CONFIG_IDE_GENERIC=y +CONFIG_BLK_DEV_SL82C105=y # CONFIG_BLK_DEV_IDEPCI is not set # CONFIG_BLK_DEV_IDEDMA is not set # CONFIG_IDEDMA_AUTO is not set diff --git a/arch/ppc/kernel/ppc_ksyms.c b/arch/ppc/kernel/ppc_ksyms.c index c35350250cf..2ba659f401b 100644 --- a/arch/ppc/kernel/ppc_ksyms.c +++ b/arch/ppc/kernel/ppc_ksyms.c @@ -12,7 +12,6 @@ #include <linux/irq.h> #include <linux/pci.h> #include <linux/delay.h> -#include <linux/ide.h> #include <linux/pm.h> #include <linux/bitops.h> @@ -124,10 +123,6 @@ EXPORT_SYMBOL(__ioremap); EXPORT_SYMBOL(iounmap); EXPORT_SYMBOL(ioremap_bot); /* aka VMALLOC_END */ -#if defined(CONFIG_BLK_DEV_IDE) || defined(CONFIG_BLK_DEV_IDE_MODULE) -EXPORT_SYMBOL(ppc_ide_md); -#endif - #ifdef CONFIG_PCI EXPORT_SYMBOL(isa_io_base); EXPORT_SYMBOL(isa_mem_base); diff --git a/arch/ppc/kernel/setup.c b/arch/ppc/kernel/setup.c index 294055902f0..bfddfdee0b6 100644 --- a/arch/ppc/kernel/setup.c +++ b/arch/ppc/kernel/setup.c @@ -10,7 +10,6 @@ #include <linux/reboot.h> #include <linux/delay.h> #include <linux/initrd.h> -#include <linux/ide.h> #include <linux/screen_info.h> #include <linux/bootmem.h> #include <linux/seq_file.h> @@ -57,7 +56,6 @@ extern void ppc6xx_idle(void); extern void power4_idle(void); extern boot_infos_t *boot_infos; -struct ide_machdep_calls ppc_ide_md; /* Used with the BI_MEMSIZE bootinfo parameter to store the memory size value reported by the boot loader. */ diff --git a/arch/ppc/platforms/4xx/bamboo.c b/arch/ppc/platforms/4xx/bamboo.c index 017623c9bc4..01f20f4c14f 100644 --- a/arch/ppc/platforms/4xx/bamboo.c +++ b/arch/ppc/platforms/4xx/bamboo.c @@ -22,7 +22,6 @@ #include <linux/blkdev.h> #include <linux/console.h> #include <linux/delay.h> -#include <linux/ide.h> #include <linux/initrd.h> #include <linux/seq_file.h> #include <linux/root_dev.h> diff --git a/arch/ppc/platforms/4xx/ebony.c b/arch/ppc/platforms/4xx/ebony.c index 453643a0eee..8027a36fc5b 100644 --- a/arch/ppc/platforms/4xx/ebony.c +++ b/arch/ppc/platforms/4xx/ebony.c @@ -25,7 +25,6 @@ #include <linux/blkdev.h> #include <linux/console.h> #include <linux/delay.h> -#include <linux/ide.h> #include <linux/initrd.h> #include <linux/seq_file.h> #include <linux/root_dev.h> diff --git a/arch/ppc/platforms/4xx/luan.c b/arch/ppc/platforms/4xx/luan.c index b79ebb8a3e6..f6d8c2e8b6b 100644 --- a/arch/ppc/platforms/4xx/luan.c +++ b/arch/ppc/platforms/4xx/luan.c @@ -23,7 +23,6 @@ #include <linux/blkdev.h> #include <linux/console.h> #include <linux/de |