diff options
| -rw-r--r-- | Documentation/i2c/chips/pcf8575 | 69 | ||||
| -rw-r--r-- | drivers/i2c/chips/Kconfig | 18 | ||||
| -rw-r--r-- | drivers/i2c/chips/Makefile | 1 | ||||
| -rw-r--r-- | drivers/i2c/chips/pcf8575.c | 198 |
4 files changed, 0 insertions, 286 deletions
diff --git a/Documentation/i2c/chips/pcf8575 b/Documentation/i2c/chips/pcf8575 deleted file mode 100644 index 40b268eb276..00000000000 --- a/Documentation/i2c/chips/pcf8575 +++ /dev/null @@ -1,69 +0,0 @@ -About the PCF8575 chip and the pcf8575 kernel driver -==================================================== - -The PCF8575 chip is produced by the following manufacturers: - - * Philips NXP - http://www.nxp.com/#/pip/cb=[type=product,path=50807/41735/41850,final=PCF8575_3]|pip=[pip=PCF8575_3][0] - - * Texas Instruments - http://focus.ti.com/docs/prod/folders/print/pcf8575.html - - -Some vendors sell small PCB's with the PCF8575 mounted on it. You can connect -such a board to a Linux host via e.g. an USB to I2C interface. Examples of -PCB boards with a PCF8575: - - * SFE Breakout Board for PCF8575 I2C Expander by RobotShop - http://www.robotshop.ca/home/products/robot-parts/electronics/adapters-converters/sfe-pcf8575-i2c-expander-board.html - - * Breakout Board for PCF8575 I2C Expander by Spark Fun Electronics - http://www.sparkfun.com/commerce/product_info.php?products_id=8130 - - -Description ------------ -The PCF8575 chip is a 16-bit I/O expander for the I2C bus. Up to eight of -these chips can be connected to the same I2C bus. You can find this -chip on some custom designed hardware, but you won't find it on PC -motherboards. - -The PCF8575 chip consists of a 16-bit quasi-bidirectional port and an I2C-bus -interface. Each of the sixteen I/O's can be independently used as an input or -an output. To set up an I/O pin as an input, you have to write a 1 to the -corresponding output. - -For more information please see the datasheet. - - -Detection ---------- - -There is no method known to detect whether a chip on a given I2C address is -a PCF8575 or whether it is any other I2C device, so you have to pass the I2C -bus and address of the installed PCF8575 devices explicitly to the driver at -load time via the force=... parameter. - -/sys interface --------------- - -For each address on which a PCF8575 chip was found or forced the following -files will be created under /sys: -* /sys/bus/i2c/devices/<bus>-<address>/read -* /sys/bus/i2c/devices/<bus>-<address>/write -where bus is the I2C bus number (0, 1, ...) and address is the four-digit -hexadecimal representation of the 7-bit I2C address of the PCF8575 -(0020 .. 0027). - -The read file is read-only. Reading it will trigger an I2C read and will hence -report the current input state for the pins configured as inputs, and the -current output value for the pins configured as outputs. - -The write file is read-write. Writing a value to it will configure all pins -as output for which the corresponding bit is zero. Reading the write file will -return the value last written, or -EAGAIN if no value has yet been written to -the write file. - -On module initialization the configuration of the chip is not changed -- the -chip is left in the state it was already configured in through either power-up -or through previous I2C write actions. diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig index 02d746c9c47..1b5455ec290 100644 --- a/drivers/i2c/chips/Kconfig +++ b/drivers/i2c/chips/Kconfig @@ -33,24 +33,6 @@ config SENSORS_PCF8574 These devices are hard to detect and rarely found on mainstream hardware. If unsure, say N. -config PCF8575 - tristate "Philips PCF8575 (DEPRECATED)" - default n - depends on GPIO_PCF857X = "n" - help - If you say yes here you get support for Philips PCF8575 chip. - This chip is a 16-bit I/O expander for the I2C bus. Several other - chip manufacturers sell equivalent chips, e.g. Texas Instruments. - - This driver can also be built as a module. If so, the module - will be called pcf8575. - - This driver is deprecated and will be dropped soon. Use - drivers/gpio/pcf857x.c instead. - - This device is hard to detect and is rarely found on mainstream - hardware. If unsure, say N. - config SENSORS_PCA9539 tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)" depends on EXPERIMENTAL && GPIO_PCA953X = "n" diff --git a/drivers/i2c/chips/Makefile b/drivers/i2c/chips/Makefile index f4680d16ee3..fceb377f528 100644 --- a/drivers/i2c/chips/Makefile +++ b/drivers/i2c/chips/Makefile @@ -13,7 +13,6 @@ obj-$(CONFIG_DS1682) += ds1682.o obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o -obj-$(CONFIG_PCF8575) += pcf8575.o obj-$(CONFIG_SENSORS_TSL2550) += tsl2550.o ifeq ($(CONFIG_I2C_DEBUG_CHIP),y) diff --git a/drivers/i2c/chips/pcf8575.c b/drivers/i2c/chips/pcf8575.c deleted file mode 100644 index 07fd7cb3c57..00000000000 --- a/drivers/i2c/chips/pcf8575.c +++ /dev/null @@ -1,198 +0,0 @@ -/* - pcf8575.c - - About the PCF8575 chip: the PCF8575 is a 16-bit I/O expander for the I2C bus - produced by a.o. Philips Semiconductors. - - Copyright (C) 2006 Michael Hennerich, Analog Devices Inc. - <hennerich@blackfin.uclinux.org> - Based on pcf8574.c. - - Copyright (c) 2007 Bart Van Assche <bart.vanassche@gmail.com>. - Ported this driver from ucLinux to the mainstream Linux kernel. - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -*/ - -#include <linux/module.h> -#include <linux/init.h> -#include <linux/i2c.h> -#include <linux/slab.h> /* kzalloc() */ -#include <linux/sysfs.h> /* sysfs_create_group() */ - -/* Addresses to scan: none, device can't be detected */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD; - - -/* Each client has this additional data */ -struct pcf8575_data { - int write; /* last written value, or error code */ -}; - -/* following are the sysfs callback functions */ -static ssize_t show_read(struct device *dev, struct device_attribute *attr, - char *buf) -{ - struct i2c_client *client = to_i2c_client(dev); - u16 val; - u8 iopin_state[2]; - - i2c_master_recv(client, iopin_state, 2); - - val = iopin_state[0]; - val |= iopin_state[1] << 8; - - return sprintf(buf, "%u\n", val); -} - -static DEVICE_ATTR(read, S_IRUGO, show_read, NULL); - -static ssize_t show_write(struct device *dev, struct device_attribute *attr, - char *buf) -{ - struct pcf8575_data *data = dev_get_drvdata(dev); - if (data->write < 0) - return data->write; - return sprintf(buf, "%d\n", data->write); -} - -static ssize_t set_write(struct device *dev, struct device_attribute *attr, - const char *buf, size_t count) -{ - struct i2c_client *client = to_i2c_client(dev); - struct pcf8575_data *data = i2c_get_clientdata(client); - unsigned long val = simple_strtoul(buf, NULL, 10); - u8 iopin_state[2]; - - if (val > 0xffff) - return -EINVAL; - - data->write = val; - - iopin_state[0] = val & 0xFF; - iopin_state[1] = val >> 8; - - i2c_master_send(client, iopin_state, 2); - - return count; -} - -static DEVICE_ATTR(write, S_IWUSR | S_IRUGO, show_write, set_write); - -static struct attribute *pcf8575_attributes[] = { - &dev_attr_read.attr, - &dev_attr_write.attr, - NULL -}; - -static const struct attribute_group pcf8575_attr_group = { - .attrs = pcf8575_attributes, -}; - -/* - * Real code - */ - -/* Return 0 if detection is successful, -ENODEV otherwise */ -static int pcf8575_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - - if (!i2c_check_functionality(adapter, I2C_FUNC_I2C)) - return -ENODEV; - - /* This is the place to detect whether the chip at the specified - address really is a PCF8575 chip. However, there is no method known - to detect whether an I2C chip is a PCF8575 or any other I2C chip. */ - - strlcpy(info->type, "pcf8575", I2C_NAME_SIZE); - - return 0; -} - -static int pcf8575_probe(struct i2c_client *client, - const struct i2c_device_id *id) -{ - struct pcf8575_data *data; - int err; - - data = kzalloc(sizeof(struct pcf8575_data), GFP_KERNEL); - if (!data) { - err = -ENOMEM; - goto exit; - } - - i2c_set_clientdata(client, data); - data->write = -EAGAIN; - - /* Register sysfs hooks */ - err = sysfs_create_group(&client->dev.kobj, &pcf8575_attr_group); - if (err) - goto exit_free; - - return 0; - -exit_free: - kfree(data); -exit: - return err; -} - -static int pcf8575_remove(struct i2c_client *client) -{ - sysfs_remove_group(&client->dev.kobj, &pcf8575_attr_group); - kfree(i2c_get_clientdata(client)); - return 0; -} - -static const struct i2c_device_id pcf8575_id[] = { - { "pcf8575", 0 }, - { } -}; - -static struct i2c_driver pcf8575_driver = { - .driver = { - .owner = THIS_MODULE, - .name = "pcf8575", - }, - .probe = pcf8575_probe, - .remove = pcf8575_remove, - .id_table = pcf8575_id, - - .detect = pcf8575_detect, - .address_data = &addr_data, -}; - -static int __init pcf8575_init(void) -{ - return i2c_add_driver(&pcf8575_driver); -} - -static void __exit pcf8575_exit(void) -{ - i2c_del_driver(&pcf8575_driver); -} - -MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>, " - "Bart Van Assche <bart.vanassche@gmail.com>"); -MODULE_DESCRIPTION("pcf8575 driver"); -MODULE_LICENSE("GPL"); - -module_init(pcf8575_init); -module_exit(pcf8575_exit); |