diff options
| -rw-r--r-- | drivers/net/bnx2x/bnx2x_hsi.h | 4 | ||||
| -rw-r--r-- | drivers/net/bnx2x/bnx2x_link.c | 42 |
2 files changed, 46 insertions, 0 deletions
diff --git a/drivers/net/bnx2x/bnx2x_hsi.h b/drivers/net/bnx2x/bnx2x_hsi.h index 6238d4f6398..548f5631c0d 100644 --- a/drivers/net/bnx2x/bnx2x_hsi.h +++ b/drivers/net/bnx2x/bnx2x_hsi.h @@ -352,6 +352,10 @@ struct port_hw_cfg { /* port 0: 0x12c port 1: 0x2bc */ #define PORT_HW_CFG_LANE_SWAP_CFG_31203120 0x0000d8d8 /* forced only */ #define PORT_HW_CFG_LANE_SWAP_CFG_32103210 0x0000e4e4 + /* Indicate whether to swap the external phy polarity */ +#define PORT_HW_CFG_SWAP_PHY_POLARITY_MASK 0x00010000 +#define PORT_HW_CFG_SWAP_PHY_POLARITY_DISABLED 0x00000000 +#define PORT_HW_CFG_SWAP_PHY_POLARITY_ENABLED 0x00010000 u32 external_phy_config; #define PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK 0xff000000 diff --git a/drivers/net/bnx2x/bnx2x_link.c b/drivers/net/bnx2x/bnx2x_link.c index 43b0de24f39..77f9eb193cb 100644 --- a/drivers/net/bnx2x/bnx2x_link.c +++ b/drivers/net/bnx2x/bnx2x_link.c @@ -4108,6 +4108,25 @@ static u8 bnx2x_8073_config_init(struct bnx2x_phy *phy, DP(NETIF_MSG_LINK, "Before rom RX_ALARM(port1): 0x%x\n", tmp1); + /** + * If this is forced speed, set to KR or KX (all other are not + * supported) + */ + /* Swap polarity if required - Must be done only in non-1G mode */ + if (params->lane_config & PORT_HW_CFG_SWAP_PHY_POLARITY_ENABLED) { + /* Configure the 8073 to swap _P and _N of the KR lines */ + DP(NETIF_MSG_LINK, "Swapping polarity for the 8073\n"); + /* 10G Rx/Tx and 1G Tx signal polarity swap */ + bnx2x_cl45_read(bp, phy, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_OPT_DIGITAL_CTRL, &val); + bnx2x_cl45_write(bp, phy, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_OPT_DIGITAL_CTRL, + (val | (3<<9))); + } + + /* Enable CL37 BAM */ if (REG_RD(bp, params->shmem_base + offsetof(struct shmem_region, dev_info. @@ -4314,6 +4333,29 @@ static u8 bnx2x_8073_read_status(struct bnx2x_phy *phy, } if (link_up) { + /* Swap polarity if required */ + if (params->lane_config & + PORT_HW_CFG_SWAP_PHY_POLARITY_ENABLED) { + /* Configure the 8073 to swap P and N of the KR lines */ + bnx2x_cl45_read(bp, phy, + MDIO_XS_DEVAD, + MDIO_XS_REG_8073_RX_CTRL_PCIE, &val1); + /** + * Set bit 3 to invert Rx in 1G mode and clear this bit + * when it`s in 10G mode. + */ + if (vars->line_speed == SPEED_1000) { + DP(NETIF_MSG_LINK, "Swapping 1G polarity for" + "the 8073\n"); + val1 |= (1<<3); + } else + val1 &= ~(1<<3); + + bnx2x_cl45_write(bp, phy, + MDIO_XS_DEVAD, + MDIO_XS_REG_8073_RX_CTRL_PCIE, + val1); + } bnx2x_ext_phy_10G_an_resolve(bp, phy, vars); bnx2x_8073_resolve_fc(phy, params, vars); } |