aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--arch/arm/mach-lpc32xx/phy3250.c7
-rw-r--r--arch/arm/mach-u300/dummyspichip.c5
-rw-r--r--arch/arm/mach-u300/spi.c10
-rw-r--r--arch/arm/mach-ux500/board-mop500.c8
-rw-r--r--drivers/mfd/ab8500-spi.c5
-rw-r--r--drivers/spi/amba-pl022.c121
-rw-r--r--include/linux/amba/pl022.h6
7 files changed, 63 insertions, 99 deletions
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index bc9a42da214..0c936cf5675 100644
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -172,18 +172,12 @@ static void phy3250_spi_cs_set(u32 control)
}
static struct pl022_config_chip spi0_chip_info = {
- .lbm = LOOPBACK_DISABLED,
.com_mode = INTERRUPT_TRANSFER,
.iface = SSP_INTERFACE_MOTOROLA_SPI,
.hierarchy = SSP_MASTER,
.slave_tx_disable = 0,
- .endian_tx = SSP_TX_LSB,
- .endian_rx = SSP_RX_LSB,
- .data_size = SSP_DATA_BITS_8,
.rx_lev_trig = SSP_RX_4_OR_MORE_ELEM,
.tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC,
- .clk_phase = SSP_CLK_FIRST_EDGE,
- .clk_pol = SSP_CLK_POL_IDLE_LOW,
.ctrl_len = SSP_BITS_8,
.wait_state = SSP_MWIRE_WAIT_ZERO,
.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
@@ -239,6 +233,7 @@ static int __init phy3250_spi_board_register(void)
.max_speed_hz = 5000000,
.bus_num = 0,
.chip_select = 0,
+ .mode = SPI_MODE_0,
.platform_data = &eeprom,
.controller_data = &spi0_chip_info,
},
diff --git a/arch/arm/mach-u300/dummyspichip.c b/arch/arm/mach-u300/dummyspichip.c
index 5f55012b7c9..03f79361259 100644
--- a/arch/arm/mach-u300/dummyspichip.c
+++ b/arch/arm/mach-u300/dummyspichip.c
@@ -46,7 +46,6 @@ static ssize_t dummy_looptest(struct device *dev,
* struct, this is just used here to alter the behaviour of the chip
* in order to perform tests.
*/
- struct pl022_config_chip *chip_info = spi->controller_data;
int status;
u8 txbuf[14] = {0xDE, 0xAD, 0xBE, 0xEF, 0x2B, 0xAD,
0xCA, 0xFE, 0xBA, 0xBE, 0xB1, 0x05,
@@ -72,7 +71,7 @@ static ssize_t dummy_looptest(struct device *dev,
* Force chip to 8 bit mode
* WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
*/
- chip_info->data_size = SSP_DATA_BITS_8;
+ spi->bits_per_word = 8;
/* You should NOT DO THIS EITHER */
spi->master->setup(spi);
@@ -159,7 +158,7 @@ static ssize_t dummy_looptest(struct device *dev,
* Force chip to 16 bit mode
* WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
*/
- chip_info->data_size = SSP_DATA_BITS_16;
+ spi->bits_per_word = 16;
/* You should NOT DO THIS EITHER */
spi->master->setup(spi);
diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c
index f0e887bea30..edb2c0d255c 100644
--- a/arch/arm/mach-u300/spi.c
+++ b/arch/arm/mach-u300/spi.c
@@ -30,8 +30,6 @@ static void select_dummy_chip(u32 chipselect)
}
struct pl022_config_chip dummy_chip_info = {
- /* Nominally this is LOOPBACK_DISABLED, but this is our dummy chip! */
- .lbm = LOOPBACK_ENABLED,
/*
* available POLLING_TRANSFER and INTERRUPT_TRANSFER,
* DMA_TRANSFER does not work
@@ -42,14 +40,8 @@ struct pl022_config_chip dummy_chip_info = {
.hierarchy = SSP_MASTER,
/* 0 = drive TX even as slave, 1 = do not drive TX as slave */
.slave_tx_disable = 0,
- /* LSB first */
- .endian_tx = SSP_TX_LSB,
- .endian_rx = SSP_RX_LSB,
- .data_size = SSP_DATA_BITS_8, /* used to be 12 in some default */
.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
- .clk_phase = SSP_CLK_SECOND_EDGE,
- .clk_pol = SSP_CLK_POL_IDLE_LOW,
.ctrl_len = SSP_BITS_12,
.wait_state = SSP_MWIRE_WAIT_ZERO,
.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
@@ -75,7 +67,7 @@ static struct spi_board_info u300_spi_devices[] = {
.bus_num = 0, /* Only one bus on this chip */
.chip_select = 0,
/* Means SPI_CS_HIGH, change if e.g low CS */
- .mode = 0,
+ .mode = SPI_MODE_1 | SPI_LSB_FIRST | SPI_LOOP,
},
#endif
};
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index 0e8fd135a57..219ae0ca4ee 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -55,19 +55,13 @@ static void ab4500_spi_cs_control(u32 command)
}
struct pl022_config_chip ab4500_chip_info = {
- .lbm = LOOPBACK_DISABLED,
.com_mode = INTERRUPT_TRANSFER,
.iface = SSP_INTERFACE_MOTOROLA_SPI,
/* we can act as master only */
.hierarchy = SSP_MASTER,
.slave_tx_disable = 0,
- .endian_rx = SSP_RX_MSB,
- .endian_tx = SSP_TX_MSB,
- .data_size = SSP_DATA_BITS_24,
.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
- .clk_phase = SSP_CLK_SECOND_EDGE,
- .clk_pol = SSP_CLK_POL_IDLE_HIGH,
.cs_control = ab4500_spi_cs_control,
};
@@ -83,7 +77,7 @@ static struct spi_board_info u8500_spi_devices[] = {
.max_speed_hz = 12000000,
.bus_num = 0,
.chip_select = 0,
- .mode = SPI_MODE_0,
+ .mode = SPI_MODE_3,
.irq = IRQ_DB8500_AB8500,
},
};
diff --git a/drivers/mfd/ab8500-spi.c b/drivers/mfd/ab8500-spi.c
index e1c8b62b086..01b6d584442 100644
--- a/drivers/mfd/ab8500-spi.c
+++ b/drivers/mfd/ab8500-spi.c
@@ -83,6 +83,11 @@ static int __devinit ab8500_spi_probe(struct spi_device *spi)
struct ab8500 *ab8500;
int ret;
+ spi->bits_per_word = 24;
+ ret = spi_setup(spi);
+ if (ret < 0)
+ return ret;
+
ab8500 = kzalloc(sizeof *ab8500, GFP_KERNEL);
if (!ab8500)
return -ENOMEM;
diff --git a/drivers/spi/amba-pl022.c b/drivers/spi/amba-pl022.c
index db0c67908d2..59c90f3ccc2 100644
--- a/drivers/spi/amba-pl022.c
+++ b/drivers/spi/amba-pl022.c
@@ -1595,12 +1595,6 @@ static int destroy_queue(struct pl022 *pl022)
static int verify_controller_parameters(struct pl022 *pl022,
struct pl022_config_chip *chip_info)
{
- if ((chip_info->lbm != LOOPBACK_ENABLED)
- && (chip_info->lbm != LOOPBACK_DISABLED)) {
- dev_err(chip_info->dev,
- "loopback Mode is configured incorrectly\n");
- return -EINVAL;
- }
if ((chip_info->iface < SSP_INTERFACE_MOTOROLA_SPI)
|| (chip_info->iface > SSP_INTERFACE_UNIDIRECTIONAL)) {
dev_err(chip_info->dev,
@@ -1626,24 +1620,6 @@ static int verify_controller_parameters(struct pl022 *pl022,
"cpsdvsr is configured incorrectly\n");
return -EINVAL;
}
- if ((chip_info->endian_rx != SSP_RX_MSB)
- && (chip_info->endian_rx != SSP_RX_LSB)) {
- dev_err(chip_info->dev,
- "RX FIFO endianess is configured incorrectly\n");
- return -EINVAL;
- }
- if ((chip_info->endian_tx != SSP_TX_MSB)
- && (chip_info->endian_tx != SSP_TX_LSB)) {
- dev_err(chip_info->dev,
- "TX FIFO endianess is configured incorrectly\n");
- return -EINVAL;
- }
- if ((chip_info->data_size < SSP_DATA_BITS_4)
- || (chip_info->data_size > SSP_DATA_BITS_32)) {
- dev_err(chip_info->dev,
- "DATA Size is configured incorrectly\n");
- return -EINVAL;
- }
if ((chip_info->com_mode != INTERRUPT_TRANSFER)
&& (chip_info->com_mode != DMA_TRANSFER)
&& (chip_info->com_mode != POLLING_TRANSFER)) {
@@ -1663,20 +1639,6 @@ static int verify_controller_parameters(struct pl022 *pl022,
"TX FIFO Trigger Level is configured incorrectly\n");
return -EINVAL;
}
- if (chip_info->iface == SSP_INTERFACE_MOTOROLA_SPI) {
- if ((chip_info->clk_phase != SSP_CLK_FIRST_EDGE)
- && (chip_info->clk_phase != SSP_CLK_SECOND_EDGE)) {
- dev_err(chip_info->dev,
- "Clock Phase is configured incorrectly\n");
- return -EINVAL;
- }
- if ((chip_info->clk_pol != SSP_CLK_POL_IDLE_LOW)
- && (chip_info->clk_pol != SSP_CLK_POL_IDLE_HIGH)) {
- dev_err(chip_info->dev,
- "Clock Polarity is configured incorrectly\n");
- return -EINVAL;
- }
- }
if (chip_info->iface == SSP_INTERFACE_NATIONAL_MICROWIRE) {
if ((chip_info->ctrl_len < SSP_BITS_4)
|| (chip_info->ctrl_len > SSP_BITS_32)) {
@@ -1825,23 +1787,14 @@ static int calculate_effective_freq(struct pl022 *pl022,
* controller hardware here, that is not done until the actual transfer
* commence.
*/
-
-/* FIXME: JUST GUESSING the spi->mode bits understood by this driver */
-#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \
- | SPI_LSB_FIRST | SPI_LOOP)
-
static int pl022_setup(struct spi_device *spi)
{
struct pl022_config_chip *chip_info;
struct chip_data *chip;
int status = 0;
struct pl022 *pl022 = spi_master_get_devdata(spi->master);
-
- if (spi->mode & ~MODEBITS) {
- dev_dbg(&spi->dev, "unsupported mode bits %x\n",
- spi->mode & ~MODEBITS);
- return -EINVAL;
- }
+ unsigned int bits = spi->bits_per_word;
+ u32 tmp;
if (!spi->max_speed_hz)
return -EINVAL;
@@ -1884,18 +1837,12 @@ static int pl022_setup(struct spi_device *spi)
* Set controller data default values:
* Polling is supported by default
*/
- chip_info->lbm = LOOPBACK_DISABLED;
chip_info->com_mode = POLLING_TRANSFER;
chip_info->iface = SSP_INTERFACE_MOTOROLA_SPI;
chip_info->hierarchy = SSP_SLAVE;
chip_info->slave_tx_disable = DO_NOT_DRIVE_TX;
- chip_info->endian_tx = SSP_TX_LSB;
- chip_info->endian_rx = SSP_RX_LSB;
- chip_info->data_size = SSP_DATA_BITS_12;
chip_info->rx_lev_trig = SSP_RX_1_OR_MORE_ELEM;
chip_info->tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC;
- chip_info->clk_phase = SSP_CLK_SECOND_EDGE;
- chip_info->clk_pol = SSP_CLK_POL_IDLE_LOW;
chip_info->ctrl_len = SSP_BITS_8;
chip_info->wait_state = SSP_MWIRE_WAIT_ZERO;
chip_info->duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX;
@@ -1933,12 +1880,16 @@ static int pl022_setup(struct spi_device *spi)
chip->xfer_type = chip_info->com_mode;
chip->cs_control = chip_info->cs_control;
- if (chip_info->data_size <= 8) {
- dev_dbg(&spi->dev, "1 <= n <=8 bits per word\n");
+ if (bits <= 3) {
+ /* PL022 doesn't support less than 4-bits */
+ status = -ENOTSUPP;
+ goto err_config_params;
+ } else if (bits <= 8) {
+ dev_dbg(&spi->dev, "4 <= n <=8 bits per word\n");
chip->n_bytes = 1;
chip->read = READING_U8;
chip->write = WRITING_U8;
- } else if (chip_info->data_size <= 16) {
+ } else if (bits <= 16) {
dev_dbg(&spi->dev, "9 <= n <= 16 bits per word\n");
chip->n_bytes = 2;
chip->read = READING_U16;
@@ -1955,6 +1906,7 @@ static int pl022_setup(struct spi_device *spi)
dev_err(&spi->dev,
"a standard pl022 can only handle "
"1 <= n <= 16 bit words\n");
+ status = -ENOTSUPP;
goto err_config_params;
}
}
@@ -1987,6 +1939,8 @@ static int pl022_setup(struct spi_device *spi)
/* Special setup for the ST micro extended control registers */
if (pl022->vendor->extended_cr) {
+ u32 etx;
+
if (pl022->vendor->pl023) {
/* These bits are only in the PL023 */
SSP_WRITE_BITS(chip->cr1, chip_info->clkdelay,
@@ -2002,29 +1956,51 @@ static int pl022_setup(struct spi_device *spi)
SSP_WRITE_BITS(chip->cr1, chip_info->wait_state,
SSP_CR1_MASK_MWAIT_ST, 6);
}
- SSP_WRITE_BITS(chip->cr0, chip_info->data_size,
+ SSP_WRITE_BITS(chip->cr0, bits - 1,
SSP_CR0_MASK_DSS_ST, 0);
- SSP_WRITE_BITS(chip->cr1, chip_info->endian_rx,
- SSP_CR1_MASK_RENDN_ST, 4);
- SSP_WRITE_BITS(chip->cr1, chip_info->endian_tx,
- SSP_CR1_MASK_TENDN_ST, 5);
+
+ if (spi->mode & SPI_LSB_FIRST) {
+ tmp = SSP_RX_LSB;
+ etx = SSP_TX_LSB;
+ } else {
+ tmp = SSP_RX_MSB;
+ etx = SSP_TX_MSB;
+ }
+ SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_RENDN_ST, 4);
+ SSP_WRITE_BITS(chip->cr1, etx, SSP_CR1_MASK_TENDN_ST, 5);
SSP_WRITE_BITS(chip->cr1, chip_info->rx_lev_trig,
SSP_CR1_MASK_RXIFLSEL_ST, 7);
SSP_WRITE_BITS(chip->cr1, chip_info->tx_lev_trig,
SSP_CR1_MASK_TXIFLSEL_ST, 10);
} else {
- SSP_WRITE_BITS(chip->cr0, chip_info->data_size,
+ SSP_WRITE_BITS(chip->cr0, bits - 1,
SSP_CR0_MASK_DSS, 0);
SSP_WRITE_BITS(chip->cr0, chip_info->iface,
SSP_CR0_MASK_FRF, 4);
}
+
/* Stuff that is common for all versions */
- SSP_WRITE_BITS(chip->cr0, chip_info->clk_pol, SSP_CR0_MASK_SPO, 6);
- SSP_WRITE_BITS(chip->cr0, chip_info->clk_phase, SSP_CR0_MASK_SPH, 7);
+ if (spi->mode & SPI_CPOL)
+ tmp = SSP_CLK_POL_IDLE_HIGH;
+ else
+ tmp = SSP_CLK_POL_IDLE_LOW;
+ SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPO, 6);
+
+ if (spi->mode & SPI_CPHA)
+ tmp = SSP_CLK_SECOND_EDGE;
+ else
+ tmp = SSP_CLK_FIRST_EDGE;
+ SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPH, 7);
+
SSP_WRITE_BITS(chip->cr0, chip_info->clk_freq.scr, SSP_CR0_MASK_SCR, 8);
/* Loopback is available on all versions except PL023 */
- if (!pl022->vendor->pl023)
- SSP_WRITE_BITS(chip->cr1, chip_info->lbm, SSP_CR1_MASK_LBM, 0);
+ if (!pl022->vendor->pl023) {
+ if (spi->mode & SPI_LOOP)
+ tmp = LOOPBACK_ENABLED;
+ else
+ tmp = LOOPBACK_DISABLED;
+ SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_LBM, 0);
+ }
SSP_WRITE_BITS(chip->cr1, SSP_DISABLED, SSP_CR1_MASK_SSE, 1);
SSP_WRITE_BITS(chip->cr1, chip_info->hierarchy, SSP_CR1_MASK_MS, 2);
SSP_WRITE_BITS(chip->cr1, chip_info->slave_tx_disable, SSP_CR1_MASK_SOD, 3);
@@ -2033,6 +2009,7 @@ static int pl022_setup(struct spi_device *spi)
spi_set_ctldata(spi, chip);
return status;
err_config_params:
+ spi_set_ctldata(spi, NULL);
err_first_setup:
kfree(chip);
return status;
@@ -2095,6 +2072,14 @@ pl022_probe(struct amba_device *adev, struct amba_id *id)
master->setup = pl022_setup;
master->transfer = pl022_transfer;
+ /*
+ * Supports mode 0-3, loopback, and active low CS. Transfers are
+ * always MS bit first on the original pl022.
+ */
+ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
+ if (pl022->vendor->extended_cr)
+ master->mode_bits |= SPI_LSB_FIRST;
+
dev_dbg(&adev->dev, "BUSNO: %d\n", master->bus_num);
status = amba_request_regions(adev, NULL);
diff --git a/include/linux/amba/pl022.h b/include/linux/amba/pl022.h
index db6a191ddcf..bf143663df8 100644
--- a/include/linux/amba/pl022.h
+++ b/include/linux/amba/pl022.h
@@ -277,19 +277,13 @@ struct pl022_ssp_controller {
*/
struct pl022_config_chip {
struct device *dev;
- enum ssp_loopback lbm;
enum ssp_interface iface;
enum ssp_hierarchy hierarchy;
bool slave_tx_disable;
struct ssp_clock_params clk_freq;
- enum ssp_rx_endian endian_rx;
- enum ssp_tx_endian endian_tx;
- enum ssp_data_size data_size;
enum ssp_mode com_mode;
enum ssp_rx_level_trig rx_lev_trig;
enum ssp_tx_level_trig tx_lev_trig;
- enum ssp_spi_clk_phase clk_phase;
- enum ssp_spi_clk_pol clk_pol;
enum ssp_microwire_ctrl_len ctrl_len;
enum ssp_microwire_wait_state wait_state;
enum ssp_duplex duplex;
generated by cgit v1.2.3-18-g5258 (git 2.32.0) at 2024-12-14 12:45:35 +0000