Bluetooth: Defer SCO setup if mode change is pending

Certain headsets such as the Motorola H350 will reject SCO and eSCO
connection requests while the ACL is transitioning from sniff mode
to active mode. Add synchronization so that SCO and eSCO connection
requests will wait until the ACL has fully transitioned to active mode.

< HCI Command: Exit Sniff Mode (0x02|0x0004) plen 2
    handle 12
> HCI Event: Command Status (0x0f) plen 4
    Exit Sniff Mode (0x02|0x0004) status 0x00 ncmd 1
< HCI Command:  Setup Synchronous Connection (0x01|0x0028) plen 17
    handle 12 voice setting 0x0040
> HCI Event: Command Status (0x0f) plen 4
    Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
> HCI Event: Number of Completed Packets (0x13) plen 5
    handle 12 packets 1
> HCI Event: Mode Change (0x14) plen 6
    status 0x00 handle 12 mode 0x00 interval 0
    Mode: Active
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
    status 0x10 handle 14 bdaddr 00:1A:0E:50:28:A4 type SCO
    Error: Connection Accept Timeout Exceeded

Signed-off-by: Ron Shaffer <rshaffer@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

1 files changed, 28 insertions, 4 deletions

diff --git a/net/bluetooth/hci_conn.c b/net/bluetooth/hci_conn.c
index e9fef83449f..0b1e460fe44 100644
--- a/net/bluetooth/hci_conn.c
+++ b/net/bluetooth/hci_conn.c
@@ -155,6 +155,27 @@ void hci_setup_sync(struct hci_conn *conn, __u16 handle)
 	hci_send_cmd(hdev, HCI_OP_SETUP_SYNC_CONN, sizeof(cp), &cp);
 }
 
+/* Device _must_ be locked */
+void hci_sco_setup(struct hci_conn *conn, __u8 status)
+{
+	struct hci_conn *sco = conn->link;
+
+	BT_DBG("%p", conn);
+
+	if (!sco)
+		return;
+
+	if (!status) {
+		if (lmp_esco_capable(conn->hdev))
+			hci_setup_sync(sco, conn->handle);
+		else
+			hci_add_sco(sco, conn->handle);
+	} else {
+		hci_proto_connect_cfm(sco, status);
+		hci_conn_del(sco);
+	}
+}
+
 static void hci_conn_timeout(unsigned long arg)
 {
 	struct hci_conn *conn = (void *) arg;
@@ -385,10 +406,13 @@ struct hci_conn *hci_connect(struct hci_dev *hdev, int type, bdaddr_t *dst, __u8
 		acl->power_save = 1;
 		hci_conn_enter_active_mode(acl);
 
-		if (lmp_esco_capable(hdev))
-			hci_setup_sync(sco, acl->handle);
-		else
-			hci_add_sco(sco, acl->handle);
+		if (test_bit(HCI_CONN_MODE_CHANGE_PEND, &acl->pend)) {
+			/* defer SCO setup until mode change completed */
+			set_bit(HCI_CONN_SCO_SETUP_PEND, &acl->pend);
+			return sco;
+		}
+
+		hci_sco_setup(acl, 0x00);
 	}
 
 	return sco;