Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
  qlcnic: adding co maintainer
  ixgbe: add support for active DA cables
  ixgbe: dcb, do not tag tc_prio_control frames
  ixgbe: fix ixgbe_tx_is_paused logic
  ixgbe: always enable vlan strip/insert when DCB is enabled
  ixgbe: remove some redundant code in setting FCoE FIP filter
  ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
  ixgbe: fix header len when unsplit packet overflows to data buffer
  ipv6: Never schedule DAD timer on dead address
  ipv6: Use POSTDAD state
  ipv6: Use state_lock to protect ifa state
  ipv6: Replace inet6_ifaddr->dead with state
  cxgb4: notify upper drivers if the device is already up when they load
  cxgb4: keep interrupts available when the ports are brought down
  cxgb4: fix initial addition of MAC address
  cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
  cnic: Convert cnic_local_flags to atomic ops.
  can: Fix SJA1000 command register writes on SMP systems
  bridge: fix build for CONFIG_SYSFS disabled
  ARCNET: Limit com20020 PCI ID matches for SOHARD cards
  ...

Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).

Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c

116 files changed, 3252 insertions, 739 deletions

diff --git a/include/linux/Kbuild b/include/linux/Kbuild
index e2ea0b2159c..2fc8e14cc24 100644
--- a/include/linux/Kbuild
+++ b/include/linux/Kbuild
@@ -94,6 +94,7 @@ header-y += if_ppp.h
 header-y += if_slip.h
 header-y += if_strip.h
 header-y += if_tun.h
+header-y += if_x25.h
 header-y += in_route.h
 header-y += ioctl.h
 header-y += ip6_tunnel.h
diff --git a/include/linux/caif/caif_socket.h b/include/linux/caif/caif_socket.h
new file mode 100644
index 00000000000..2a61eb1beb8
--- /dev/null
+++ b/include/linux/caif/caif_socket.h
@@ -0,0 +1,165 @@
+/* linux/caif_socket.h
+ * CAIF Definitions for CAIF socket and network layer
+ * Copyright (C) ST-Ericsson AB 2010
+ * Author:	 Sjur Brendeland/ sjur.brandeland@stericsson.com
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#ifndef _LINUX_CAIF_SOCKET_H
+#define _LINUX_CAIF_SOCKET_H
+
+#include <linux/types.h>
+
+#ifdef __KERNEL__
+#include <linux/socket.h>
+#else
+#include <sys/socket.h>
+#endif
+
+/**
+ * enum caif_link_selector -    Physical Link Selection.
+ * @CAIF_LINK_HIGH_BANDW:	Physical interface for high-bandwidth
+ *				traffic.
+ * @CAIF_LINK_LOW_LATENCY:	Physical interface for low-latency
+ *				traffic.
+ *
+ * CAIF Link Layers can register their link properties.
+ * This enum is used for choosing between CAIF Link Layers when
+ * setting up CAIF Channels when multiple CAIF Link Layers exists.
+ */
+enum caif_link_selector {
+	CAIF_LINK_HIGH_BANDW,
+	CAIF_LINK_LOW_LATENCY
+};
+
+/**
+ * enum caif_channel_priority - CAIF channel priorities.
+ *
+ * @CAIF_PRIO_MIN:	Min priority for a channel.
+ * @CAIF_PRIO_LOW:	Low-priority channel.
+ * @CAIF_PRIO_NORMAL:	Normal/default priority level.
+ * @CAIF_PRIO_HIGH:	High priority level
+ * @CAIF_PRIO_MAX:	Max priority for channel
+ *
+ * Priority can be set on CAIF Channels in order to
+ * prioritize between traffic on different CAIF Channels.
+ * These priority levels are recommended, but the priority value
+ * is not restricted to the values defined in this enum, any value
+ * between CAIF_PRIO_MIN and CAIF_PRIO_MAX could be used.
+ */
+enum caif_channel_priority {
+	CAIF_PRIO_MIN	 = 0x01,
+	CAIF_PRIO_LOW	 = 0x04,
+	CAIF_PRIO_NORMAL = 0x0f,
+	CAIF_PRIO_HIGH	 = 0x14,
+	CAIF_PRIO_MAX	 = 0x1F
+};
+
+/**
+ * enum caif_protocol_type  -	CAIF Channel type.
+ * @CAIFPROTO_AT:		Classic AT channel.
+ * @CAIFPROTO_DATAGRAM:	Datagram channel.
+ * @CAIFPROTO_DATAGRAM_LOOP:	Datagram loopback channel, used for testing.
+ * @CAIFPROTO_UTIL:		Utility (Psock) channel.
+ * @CAIFPROTO_RFM:		Remote File Manager
+ *
+ * This enum defines the CAIF Channel type to be used. This defines
+ * the service to connect to on the modem.
+ */
+enum caif_protocol_type {
+	CAIFPROTO_AT,
+	CAIFPROTO_DATAGRAM,
+	CAIFPROTO_DATAGRAM_LOOP,
+	CAIFPROTO_UTIL,
+	CAIFPROTO_RFM,
+	_CAIFPROTO_MAX
+};
+#define	CAIFPROTO_MAX _CAIFPROTO_MAX
+
+/**
+ * enum caif_at_type - AT Service Endpoint
+ * @CAIF_ATTYPE_PLAIN:	     Connects to a plain vanilla AT channel.
+ */
+enum caif_at_type {
+	CAIF_ATTYPE_PLAIN = 2
+};
+
+/**
+ * struct sockaddr_caif - the sockaddr structure for CAIF sockets.
+ * @family:		     Address family number, must be AF_CAIF.
+ * @u:			     Union of address data 'switched' by family.
+ * :
+ * @u.at:                    Applies when family = CAIFPROTO_AT.
+ *
+ * @u.at.type:               Type of AT link to set up (enum caif_at_type).
+ *
+ * @u.util:                  Applies when family = CAIFPROTO_UTIL
+ *
+ * @u.util.service:          Utility service name.
+ *
+ * @u.dgm:                   Applies when family = CAIFPROTO_DATAGRAM
+ *
+ * @u.dgm.connection_id:     Datagram connection id.
+ *
+ * @u.dgm.nsapi:             NSAPI of the PDP-Context.
+ *
+ * @u.rfm:                   Applies when family = CAIFPROTO_RFM
+ *
+ * @u.rfm.connection_id:     Connection ID for RFM.
+ *
+ * @u.rfm.volume:            Volume to mount.
+ *
+ * Description:
+ * This structure holds the connect parameters used for setting up a
+ * CAIF Channel. It defines the service to connect to on the modem.
+ */
+struct sockaddr_caif {
+	sa_family_t  family;
+	union {
+		struct {
+			__u8  type;		/* type: enum caif_at_type */
+		} at;				/* CAIFPROTO_AT */
+		struct {
+			char	  service[16];
+		} util;				/* CAIFPROTO_UTIL */
+		union {
+			__u32 connection_id;
+			__u8  nsapi;
+		} dgm;				/* CAIFPROTO_DATAGRAM(_LOOP)*/
+		struct {
+			__u32 connection_id;
+			char	  volume[16];
+		} rfm;				/* CAIFPROTO_RFM */
+	} u;
+};
+
+/**
+ * enum caif_socket_opts - CAIF option values for getsockopt and setsockopt.
+ *
+ * @CAIFSO_LINK_SELECT:		Selector used if multiple CAIF Link layers are
+ *				available. Either a high bandwidth
+ *				link can be selected (CAIF_LINK_HIGH_BANDW) or
+ *				or a low latency link (CAIF_LINK_LOW_LATENCY).
+ *                              This option is of type __u32.
+ *				Alternatively SO_BINDTODEVICE can be used.
+ *
+ * @CAIFSO_REQ_PARAM:		Used to set the request parameters for a
+ *				utility channel. (maximum 256 bytes). This
+ *				option must be s