[SSB]: add Sonics Silicon Backplane bus support

SSB is an SoC bus used in a number of embedded devices.  The most
well-known of these devices is probably the Linksys WRT54G, but there
are others as well.  The bus is also used internally on the BCM43xx
and BCM44xx devices from Broadcom.

This patch also includes support for SSB ID tables in modules, so
that SSB drivers can be loaded automatically.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

7 files changed, 1483 insertions, 0 deletions

diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
index 4dc5fa8be78..0c522e6b091 100644
--- a/include/linux/mod_devicetable.h
+++ b/include/linux/mod_devicetable.h
@@ -340,4 +340,19 @@ struct parisc_device_id {
 #define PA_HVERSION_ANY_ID	0xffff
 #define PA_SVERSION_ANY_ID	0xffffffff
 
+/* SSB core, see drivers/ssb/ */
+struct ssb_device_id {
+	__u16	vendor;
+	__u16	coreid;
+	__u8	revision;
+};
+#define SSB_DEVICE(_vendor, _coreid, _revision)  \
+	{ .vendor = _vendor, .coreid = _coreid, .revision = _revision, }
+#define SSB_DEVTABLE_END  \
+	{ 0, },
+
+#define SSB_ANY_VENDOR		0xFFFF
+#define SSB_ANY_ID		0xFFFF
+#define SSB_ANY_REV		0xFF
+
 #endif /* LINUX_MOD_DEVICETABLE_H */
diff --git a/include/linux/ssb/ssb.h b/include/linux/ssb/ssb.h
new file mode 100644
index 00000000000..2b5c312c496
--- /dev/null
+++ b/include/linux/ssb/ssb.h
@@ -0,0 +1,424 @@
+#ifndef LINUX_SSB_H_
+#define LINUX_SSB_H_
+
+#include <linux/device.h>
+#include <linux/list.h>
+#include <linux/types.h>
+#include <linux/spinlock.h>
+#include <linux/pci.h>
+#include <linux/mod_devicetable.h>
+
+#include <linux/ssb/ssb_regs.h>
+
+
+struct pcmcia_device;
+struct ssb_bus;
+struct ssb_driver;
+
+
+struct ssb_sprom_r1 {
+	u16 pci_spid;		/* Subsystem Product ID for PCI */
+	u16 pci_svid;		/* Subsystem Vendor ID for PCI */
+	u16 pci_pid;		/* Product ID for PCI */
+	u8 il0mac[6];		/* MAC address for 802.11b/g */
+	u8 et0mac[6];		/* MAC address for Ethernet */
+	u8 et1mac[6];		/* MAC address for 802.11a */
+	u8 et0phyaddr:5;	/* MII address for enet0 */
+	u8 et1phyaddr:5;	/* MII address for enet1 */
+	u8 et0mdcport:1;	/* MDIO for enet0 */
+	u8 et1mdcport:1;	/* MDIO for enet1 */
+	u8 board_rev;		/* Board revision */
+	u8 country_code:4;	/* Country Code */
+	u8 antenna_a:2;		/* Antenna 0/1 available for A-PHY */
+	u8 antenna_bg:2;	/* Antenna 0/1 available for B-PHY and G-PHY */
+	u16 pa0b0;
+	u16 pa0b1;
+	u16 pa0b2;
+	u16 pa1b0;
+	u16 pa1b1;
+	u16 pa1b2;
+	u8 gpio0;		/* GPIO pin 0 */
+	u8 gpio1;		/* GPIO pin 1 */
+	u8 gpio2;		/* GPIO pin 2 */
+	u8 gpio3;		/* GPIO pin 3 */
+	u16 maxpwr_a;		/* A-PHY Power Amplifier Max Power (in dBm Q5.2) */
+	u16 maxpwr_bg;		/* B/G-PHY Power Amplifier Max Power (in dBm Q5.2) */
+	u8 itssi_a;		/* Idle TSSI Target for A-PHY */
+	u8 itssi_bg;		/* Idle TSSI Target for B/G-PHY */
+	u16 boardflags_lo;	/* Boardflags (low 16 bits) */
+	u8 antenna_gain_a;	/* A-PHY Antenna gain (in dBm Q5.2) */
+	u8 antenna_gain_bg;	/* B/G-PHY Antenna gain (in dBm Q5.2) */
+	u8 oem[8];		/* OEM string (rev 1 only) */
+};
+
+struct ssb_sprom_r2 {
+	u16 boardflags_hi;	/* Boardflags (high 16 bits) */
+	u8 maxpwr_a_lo;		/* A-PHY Max Power Low */
+	u8 maxpwr_a_hi;		/* A-PHY Max Power High */
+	u16 pa1lob0;		/* A-PHY PA Low Settings */
+	u16 pa1lob1;		/* A-PHY PA Low Settings */
+	u16 pa1lob2;		/* A-PHY PA Low Settings */
+	u16 pa1hib0;		/* A-PHY PA High Settings */
+	u16 pa1hib1;		/* A-PHY PA High Settings */
+	u16 pa1hib2;		/* A-PHY PA High Settings */
+	u8 ofdm_pwr_off;	/* OFDM Power Offset from CCK Level */
+	u8 country_str[2];	/* Two char Country Code */
+};
+
+struct ssb_sprom_r3 {
+	u32 ofdmapo;		/* A-PHY OFDM Mid Power Offset */
+	u32 ofdmalpo;		/* A-PHY OFDM Low Power Offset */
+	u32 ofdmahpo;		/* A-PHY OFDM High Power Offset */
+	u8 gpioldc_on_cnt;	/* GPIO LED Powersave Duty Cycle ON count */
+	u8 gpioldc_off_cnt;	/* GPIO LED Powersave Duty Cycle OFF count */
+	u8 cckpo_1M:4;		/* CCK Power Offset for Rate 1M */
+	u8 cckpo_2M:4;		/* CCK Power Offset for Rate 2M */
+	u8 cckpo_55M:4;		/* CCK Power Offset for Rate 5.5M */
+	u8 cckpo_11M:4;		/* CCK Power Offset for Rate 11M */
+	u32 ofdmgpo;		/* G-PHY OFDM Power Offset */
+};
+
+struct ssb_sprom_r4 {
+	/* TODO */
+};
+
+struct ssb_sprom {
+	u8 revision;
+	u8 crc;
+	/* The valid r# fields are selected by the "revision".
+	 * Revision 3 and lower inherit from lower revisions.
+	 */
+	union {
+		struct {
+			struct ssb_sprom_r1 r1;
+			struct ssb_sprom_r2 r2;
+			struct ssb_sprom_r3 r3;
+		};
+		struct ssb_sprom_r4 r4;
+	};
+};
+
+/* Information about the PCB the circuitry is soldered on. */
+struct ssb_boardinfo {
+	u16 vendor;
+	u16 type;
+	u16 rev;
+};
+
+
+struct ssb_device;
+/* Lowlevel read/write operations on the device MMIO.
+ * Internal, don't use that outside of ssb. */
+struct ssb_bus_ops {
+	u16 (*read16)(struct ssb_device *dev, u16 offset);
+	u32 (*read32)(struct ssb_device *dev, u16 offset);
+	void (*write16)(struct ssb_device *dev, u16 offset, u16 value);
+	void (*write32)(struct ssb_device *dev, u16 offset, u32 value);
+};
+
+
+/* Core-ID values. */
+#define SSB_DEV_CHIPCOMMON	0x800
+#define SSB_DEV_ILINE20		0x801
+#define SSB_DEV_SDRAM		0x803
+#define SSB_DEV_PCI		0x804
+#define SSB_DEV_MIPS		0x805
+#define SSB_DEV_ETHERNET	0x806
+#define SSB_DEV_V90		0x807
+#define SSB_DEV_USB11_HOSTDEV	0x808
+#define SSB_DEV_ADSL		0x809
+#define SSB_DEV_ILINE100	0x80A
+#define SSB_DEV_IPSEC		0x80B
+#define SSB_DEV_PCMCIA		0x80D
+#define SSB_DEV_INTERNAL_MEM	0x80E
+#define SSB_DEV_MEMC_SDRAM	0x80F
+#define SSB_DEV_EXTIF		0x811
+#define SSB_DEV_80211		0x812
+#define SSB_DEV_MIPS_3302	0x816
+#define SSB_DEV_USB11_HOST	0x817
+#define SSB_DEV_USB11_DEV	0x818
+#define SSB_DEV_USB20_HOST	0x819
+#define SSB_DEV_USB20_DEV	0x81A
+#define SSB_DEV_SDIO_HOST	0x81B
+#define SSB_DEV_ROBOSWITCH	0x81C
+#define SSB_DEV_PARA_ATA	0x81D
+#define SSB_DEV_SATA_XORDMA	0x81E
+#define SSB_DEV_ETHERNET_GBIT	0x81F
+#define SSB_DEV_PCIE		0x820
+#define SSB_DEV_MIMO_PHY	0x821
+#define SSB_DEV_SRAM_CTRLR	0x822
+#define SSB_DEV_MINI_MACPHY	0x823
+#define SSB_DEV_ARM_1176	0x824
+#define SSB_DEV_ARM_7TDMI	0x825
+
+/* Vendor-ID values */
+#define SSB_VENDOR_BROADCOM	0x4243
+
+/* Some kernel subsystems poke with dev->drvdata, so we must use the
+ * following ugly workaround to get from struct device to struct ssb_device */
+struct __ssb_dev_wrapper {
+	struct device dev;
+	struct ssb_device *sdev;
+};
+
+struct ssb_device {
+	/* Having a copy of the ops pointer in each dev struct
+	 * is an optimization. */
+	const struct ssb_bus_ops *ops;
+
+	struct device *dev;
+	struct ssb_bus *bus;
+	struct ssb_device_id id;
+
+	u8 core_index;
+	unsigned int irq;
+
+	/* Internal-only stuff follows. */
+	void *drvdata;		/* Per-device data */
+	void *devtypedata;	/* Per-devicetype (eg 802.11) data */
+};
+
+/* Go from struct device to struct ssb_device. */
+static inline
+struct ssb_device * dev_to_ssb_dev(struct device *dev)
+{
+	struct __ssb_dev_wrapper *wrap;
+	wrap = container_of(dev, struct __ssb_dev_wrapper, dev);
+	return wrap->sdev;
+}
+
+/* Device specific user data */
+static inline
+void ssb_set_drvdata(struct ssb_device *dev, void *data)
+{
+	dev->drvdata = data;
+}
+static inline
+void * ssb_get_drvdata(struct ssb_device *dev)
+{
+	return dev->drvdata;
+}
+
+/* Devicetype specific user data. This is per device-type (not per device) */
+void ssb_set_devtypedata(struct ssb_device *dev, void *data);
+static inline
+void * ssb_get_devtypedata(struct ssb_device *dev)
+{
+	return dev->devtypedata;
+}
+
+
+struct ssb_driver {
+	const char *name;
+	const struct ssb_device_id *id_table;
+
+	int (*probe)(struct ssb_device *dev, const struct ssb_device_id *id);
+	void (*remove)(struct ssb_device *dev);
+	int (*suspend)(struct ssb_device *dev, pm_message_t state);
+	int (*resume)(struct ssb_device *dev);
+	void (*shutdown)(struct ssb_device *dev);
+
+	struct device_driver drv;
+};
+#define drv_to_ssb_drv(_drv) container_of(_drv, struct ssb_driver, drv)
+
+extern int __ssb_driver_register(struct ssb_driver *drv, struct module *owner);
+static inline int ssb_driver_register(struct ssb_driver *drv)
+{
+	return __ssb_driver_register(drv, THIS_MODULE);
+}
+extern void ssb_driver_unregister(struct ssb_driver *drv);
+
+
+
+
+enum ssb_bustype {
+	SSB_BUSTYPE_SSB,	/* This SSB bus is the system bus */
+	SSB_BUSTYPE_PCI,	/* SSB is connected to PCI bus */
+	SSB_BUSTYPE_PCMCIA,	/* SSB is connected to PCMCIA bus */
+};
+
+/* board_vendor */
+#define SSB_BOARDVENDOR_BCM	0x14E4	/* Broadcom */
+#define SSB_BOARDVENDOR_DELL	0x1028	/* Dell */
+#define SSB_BOARDVENDOR_HP	0x0E11	/* HP */
+/* board_type */
+#define SSB_BOARD_BCM94306MP	0x0418
+#define SSB_BOARD_BCM4309G	0x0421
+#define SSB_BOARD_BCM4306CB	0x0417
+#define SSB_BOARD_BCM4309MP	0x040C
+#define SSB_BOARD_MP4318	0x044A
+#define SSB_BOARD_BU4306	0x0416
+#define SSB_BOARD_BU4309	0x040A
+/* chip_package */
+#define SSB_CHIPPACK_BCM4712S	1	/* Small 200pin 4712 */
+#define SSB_CHIPPACK_BCM4712M	2	/* Medium 225pin 4712 */
+#define SSB_CHIPPACK_BCM4712L	0	/* Large 340pin 4712 */
+
+#include <linux/ssb/ssb_driver_chipcommon.h>
+#include <linux/ssb/ssb_driver_mips.h>
+#include <linux/ssb/ssb_driver_extif.h>
+#include <linux/ssb/ssb_driver_pci.h>
+
+struct ssb_bus {
+	/* The MMIO area. */
+	void __iomem *mmio;
+
+	const struct ssb_bus_ops *ops;
+
+	/* The core in the basic address register window. (PCI bus only) */
+	struct ssb_device *mapped_device;
+	/* Currently mapped PCMCIA segment. (bustype == SSB_BUSTYPE_PCMCIA only) */
+	u8 mapped_pcmcia_seg;
+	/* Lock for core and segment switching. */
+	spinlock_t bar_lock;
+
+	/* The bus this backplane is running on. */
+	enum ssb_bustype bustype;
+	/* Pointer to the PCI bus (only valid if bustype == SSB_BUSTYPE_PCI). */
+	struct pci_dev *host_pci;
+	/* Pointer to the PCMCIA device (only if bustype == SSB_BUSTYPE_PCMCIA). */
+	struct pcmcia_device *host_pcmcia;
+
+#ifdef CONFIG_SSB_PCIHOST
+	/* Mutex to protect the SPROM writing. */
+	struct mutex pci_sprom_mutex;
+#endif
+
+	/* ID information about the Chip. */
+	u16 chip_id;
+	u16 chip_rev;
+	u8 chip_package;
+
+	/* List of devices (cores) on the backplane. */
+	struct ssb_device devices[SSB_MAX_NR_CORES];
+	u8 nr_devices;
+
+	/* Reference count. Number of suspended devices. */
+	u8 suspend_cnt;
+
+	/* Software ID number for this bus. */
+	unsigned int busnumber;
+
+	/* The ChipCommon device (if available). */
+	struct ssb_chipcommon chipco;
+	/* The PCI-core device (if available). */
+	struct ssb_pcicore pcicore;
+	/* The MIPS-core device (if available). */
+	struct ssb_mipscore mipscore;
+	/* The EXTif-core device (if available). */
+	struct ssb_extif extif;
+
+	/* The following structure elements are not available in early
+	 * SSB initialization. Though, they are available for regular
+	 * registered drivers at any stage. So be careful when
+	 * using them in the ssb core code. */
+
+	/* ID information about the PCB. */
+	struct ssb_boardinfo boardinfo;
+	/* Contents of the SPROM. */
+	struct ssb_sprom sprom;
+
+	/* Internal-only stuff follows. Do not touch. */
+	struct list_head list;
+#ifdef CONFIG_SSB_DEBUG
+	/* Is the bus already powered up? */
+	bool powered_up;
+	int power_warn_count;
+#endif /* DEBUG */
+};
+
+/* The initialization-invariants. */
+struct ssb_init_invariants {
+	struct ssb_boardinfo boardinfo;
+	struct ssb_sprom sprom;
+};
+/* Type of function to fetch the invariants. */
+typedef int (*ssb_invariants_func_t)(struct ssb_bus *bus,
+				     struct ssb_init_invariants *iv);
+
+/* Register a SSB system bus. get_invariants() is called after the
+ * basic system devices are initialized.
+ * The invariants are usually fetched from some NVRAM.
+ * Put the invariants into the struct pointed to by iv. */
+extern int ssb_bus_ssbbus_register(struct ssb_bus *bus,
+				   unsigned long baseaddr,
+				   ssb_invariants_func_t get_invariants);
+#ifdef CONFIG_SSB_PCIHOST
+extern int ssb_bus_pcibus_register(struct ssb_bus *bus,
+				   struct pci_dev *host_pci);
+#endif /* CONFIG_SSB_PCIHOST */
+#ifdef CONFIG_SSB_PCMCIAHOST
+extern int ssb_bus_pcmciabus_register(struct ssb_bus *bus,
+				      struct pcmcia_device *pcmcia_dev,
+				      unsigned long baseaddr);
+#endif /* CONFIG_SSB_PCMCIAHOST */
+
+extern void ssb_bus_unregister(struct ssb_bus *bus);
+
+extern u32 ssb_clockspeed(struct ssb_bus *bus);
+
+/* Is the device enabled in hardware? */
+int ssb_device_is_enabled(struct ssb_device *dev);
+/* Enable a device and pass device-specific SSB_TMSLOW flags.
+ * If no device-specific flags are available, use 0. */
+void ssb_device_enable(struct ssb_device *dev, u32 core_specific_flags);
+/* Disable a device in hardware and pass SSB_TMSLOW flags (if any). */
+void ssb_device_disable(struct ssb_device *dev, u32 core_specific_flags);
+
+
+/* Device MMIO register read/write functions. */
+static inline u16 ssb_read16(struct ssb_device *dev, u16 offset)
+{
+	return dev->ops->read16(dev, offset);
+}
+static inline u32 ssb_read32(struct ssb_device *dev, u16 offset)
+{
+	return dev->ops->read32(dev, offset);
+}
+static inline void ssb_write16(struct ssb_device *dev, u16 offset, u16 value)
+{
+	dev->ops->write16(dev, offset, value);
+}
+static inline void ssb_write32(struct ssb_device *dev, u16 offset, u32 value)
+{
+	dev->ops->write32(dev, offset, value);
+}
+
+
+/* Translation (routing) bits that need to be ORed to DMA
+ * addresses before they are given to a device. */
+extern u32 ssb_dma_translation(struct ssb_device *dev);
+#define SSB_DMA_TRANSLATION_MASK	0xC0000000
+#define SSB_DMA_TRANSLATION_SHIFT	30
+
+extern int ssb_dma_set_mask(struct ssb_device *ssb_dev, u64 mask);
+
+
+#ifdef CONFIG_SSB_PCIHOST
+/* PCI-host wrapper driver */
+extern int ssb_pcihost_register(struct pci_driver *driver);
+static inline void ssb_pcihost_unregister(struct pci_driver *driver)
+{
+	pci_unregister_driver(driver);
+}
+#endif /* CONFIG_SSB_PCIHOST */
+
+
+/* If a driver is shutdown or suspended, call this to signal
+ * that the bus may be completely powered down. SSB will decide,
+ * if it's really time to power down the bus, based on if there
+ * are other devices that want to run. */
+extern int ssb_bus_may_powerdown(struct ssb_bus *bus);
+/* Before initializing and enabling a device, call this to power-up the bus.
+ * If you want to allow use of dynamic-power-control, pass the flag.
+ * Otherwise static always-on powercontrol will be used. */
+extern int ssb_bus_powerup(struct ssb_bus *bus, bool dynamic_pctl);
+
+
+/* Various helper functions */
+extern u32 ssb_admatch_base(u32 adm);
+extern u32 ssb_admatch_size(u32 adm);
+
+
+#endif /* LINUX_SSB_H_ */
diff --git a/include/linux/ssb/ssb_driver_chipcommon.h b/include/linux/ssb/ssb_driver_chipcommon.h
new file mode 100644
index 00000000000..4cb99549466
--- /dev/null
+++ b/include/linux/ssb/ssb_driver_chipcommon.h
@@ -0,0 +1,396 @@
+#ifndef LINUX_SSB_CHIPCO_H_
+#define LINUX_SSB_CHIPCO_H_
+
+/* SonicsSiliconBackplane CHIPCOMMON core hardware definitions
+ *
+ * The chipcommon core provides chip identification, SB control,
+ * jtag, 0/1/2 uarts, clock frequency control, a watchdog interrupt timer,
+ * gpio interface, extbus, and support for serial and parallel flashes.
+ *
+ * Copyright 2005, Broadcom Corporation
+ * Copyright 2006, Michael Buesch <mb@bu3sch.de>
+ *
+ * Licensed under the GPL version 2. See COPYING for details.
+ */
+
+/** ChipCommon core registers. **/
+
+#define SSB_CHIPCO_CHIPID		0x0000
+#define  SSB_CHIPCO_IDMASK		0x0000FFFF
+#define  SSB_CHIPCO_REVMASK		0x000F0000
+#define  SSB_CHIPCO_REVSHIFT		16
+#define  SSB_CHIPCO_PACKMASK		0x00F00000
+#define  SSB_CHIPCO_PACKSHIFT		20
+#define  SSB_CHIPCO_NRCORESMASK		0x0F000000
+#define  SSB_CHIPCO_NRCORESSHIFT	24
+#define SSB_CHIPCO_CAP	 		0x0004		/* Capabilities */
+#define  SSB_CHIPCO_CAP_NRUART		0x00000003	/* # of UARTs */
+#define  SSB_CHIPCO_CAP_MIPSEB		0x00000004	/* MIPS in BigEndian Mode */
+#define  SSB_CHIPCO_CAP_UARTCLK		0x00000018	/* UART clock select */
+#define   SSB_CHIPCO_CAP_UARTCLK_INT	0x00000008	/* UARTs are driven by internal divided clock */
+#define  SSB_CHIPCO_CAP_UARTGPIO	0x00000020	/* UARTs on GPIO 15-12 */
+#define  SSB_CHIPCO_CAP_EXTBUS		0x000000C0	/* External buses present */
+#define  SSB_CHIPCO_CAP_FLASHT		0x00000700	/* Flash Type */
+#define   SSB_CHIPCO_FLASHT_NONE	0x00000000	/* No flash */
+#define   SSB_CHIPCO_FLASHT_STSER	0x00000100	/* ST serial flash */
+#define   SSB_CHIPCO_FLASHT_ATSER	0x00000200	/* Atmel serial flash */
+#define	  SSB_CHIPCO_FLASHT_PARA	0x00000700	/* Parallel flash */
+#define  SSB_CHIPCO_CAP_PLLT		0x00038000	/* PLL Type */
+#define   SSB_PLLTYPE_NONE		0x00000000
+#define   SSB_PLLTYPE_1			0x00010000	/* 48Mhz base, 3 dividers */
+#define   SSB_PLLTYPE_2			0x00020000	/* 48Mhz, 4 dividers */
+#define   SSB_PLLTYPE_3			0x00030000	/* 25Mhz, 2 dividers */
+#define   SSB_PLLTYPE_4			0x00008000	/* 48Mhz, 4 dividers */
+#define   SSB_PLLTYPE_5			0x00018000	/* 25Mhz, 4 dividers */
+#define   SSB_PLLTYPE_6			0x00028000	/* 100/200 or 120/240 only */
+#define   SSB_PLLTYPE_7			0x00038000	/* 25Mhz, 4 dividers */
+#define  SSB_CHIPCO_CAP_PCTL		0x00040000	/* Power Control */
+#define  SSB_CHIPCO_CAP_OTPS		0x00380000	/* OTP size */
+#define  SSB_CHIPCO_CAP_OTPS_SHIFT	19
+#define  SSB_CHIPCO_CAP_OTPS_BASE	5
+#define  SSB_CHIPCO_CAP_JTAGM		0x00400000	/* JTAG master present */
+#define  SSB_CHIPCO_CAP_BROM		0x00800000	/* Internal boot ROM active */
+#define  SSB_CHIPCO_CAP_64BIT		0x08000000	/* 64-bit Backplane */
+#define SSB_CHIPCO_CORECTL		0x0008
+#define  SSB_CHIPCO_CORECTL_UARTCLK0	0x00000001	/* Drive UART with internal clock */
+#define	 SSB_CHIPCO_CORECTL_SE		0x00000002	/* sync clk out enable (corerev >= 3) */
+#define SSB_CHIPCO_BIST			0x000C
+#define SSB_CHIPCO_OTPS			0x0010		/* OTP status */
+#define	 SSB_CHIPCO_OTPS_PROGFAIL	0x80000000
+#define	 SSB_CHIPCO_OTPS_PROTECT	0x00000007
+#define	 SSB_CHIPCO_OTPS_HW_PROTECT	0x00000001
+#define	 SSB_CHIPCO_OTPS_SW_PROTECT	0x00000002
+#define	 SSB_CHIPCO_OTPS_CID_PROTECT	0x00000004
+#define SSB_CHIPCO_OTPC			0x0014		/* OTP control */
+#define	 SSB_CHIPCO_OTPC_RECWAIT	0xFF000000
+#define	 SSB_CHIPCO_OTPC_PROGWAIT	0x00FFFF00
+#define	 SSB_CHIPCO_OTPC_PRW_SHIFT	8
+#define	 SSB_CHIPCO_OTPC_MAXFAIL	0x00000038
+#define	 SSB_CHIPCO_OTPC_VSEL		0x00000006
+#define	 SSB_CHIPCO_OTPC_SELVL		0x00000001
+#define SSB_CHIPCO_OTPP			0x0018		/* OTP prog */
+#define	 SSB_CHIPCO_OTPP_COL		0x000000FF
+#define	 SSB_CHIPCO_OTPP_ROW		0x0000FF00
+#define	 SSB_CHIPCO_OTPP_ROW_SHIFT	8
+#define	 SSB_CHIPCO_OTPP_READERR	0x10000000
+#define	 SSB_CHIPCO_OTPP_VALUE		0x20000000
+#define	 SSB_CHIPCO_OTPP_READ		0x40000000
+#define	 SSB_CHIPCO_OTPP_START		0x80000000
+#define	 SSB_CHIPCO_OTPP_BUSY		0x80000000
+#define SSB_CHIPCO_IRQSTAT		0x0020
+#define SSB_CHIPCO_IRQMASK		0x0024
+#define	 SSB_CHIPCO_IRQ_GPIO		0x00000001	/* gpio intr */
+#define	 SSB_CHIPCO_IRQ_EXT		0x00000002	/* ro: ext intr pin (corerev >= 3) */
+#define	 SSB_CHIPCO_IRQ_WDRESET		0x80000000	/* watchdog reset occurred */
+#define SSB_CHIPCO_CHIPCTL		0x0028		/* Rev >= 11 only */
+#define SSB_CHIPCO_CHIPSTAT		0x002C		/* Rev >= 11 only */
+#define SSB_CHIPCO_JCMD			0x0030		/* Rev >= 10 only */
+#define  SSB_CHIPCO_JCMD_START		0x80000000
+#define  SSB_CHIPCO_JCMD_BUSY		0x80000000
+#define  SSB_CHIPCO_JCMD_PAUSE		0x40000000
+#define  SSB_CHIPCO_JCMD0_ACC_MASK	0x0000F000
+#define  SSB_CHIPCO_JCMD0_ACC_IRDR	0x00000000
+#define  SSB_CHIPCO_JCMD0_ACC_DR	0x00001000
+#define  SSB_CHIPCO_JCMD0_ACC_IR	0x00002000
+#define  SSB_CHIPCO_JCMD0_ACC_RESET	0x00003000
+#define  SSB_CHIPCO_JCMD0_ACC_IRPDR	0x00004000
+#define  SSB_CHIPCO_JCMD0_ACC_PDR	0x00005000
+#define  SSB_CHIPCO_JCMD0_IRW_MASK	0x00000F00
+#define  SSB_CHIPCO_JCMD_ACC_MASK	0x000F0000	/* Changes for corerev 11 */
+#define  SSB_CHIPCO_JCMD_ACC_IRDR	0x00000000
+#define  SSB_CHIPCO_JCMD_ACC_DR		0x00010000
+#define  SSB_CHIPCO_JCMD_ACC_IR		0x00020000
+#define  SSB_CHIPCO_JCMD_ACC_RESET	0x00030000
+#define  SSB_CHIPCO_JCMD_ACC_IRPDR	0x00040000
+#define  SSB_CHIPCO_JCMD_ACC_PDR	0x00050000
+#define  SSB_CHIPCO_JCMD_IRW_MASK	0x00001F00
+#define  SSB_CHIPCO_JCMD_IRW_SHIFT	8
+#define  SSB_CHIPCO_JCMD_DRW_MASK	0x0000003F
+#define SSB_CHIPCO_JIR			0x0034		/* Rev >= 10 only */
+#define SSB_CHIPCO_JDR			0x0038		/* Rev >= 10 only */
+#define SSB_CHIPCO_JCTL			0x003C		/* Rev >= 10 only */
+#define  SSB_CHIPCO_JCTL_FORCE_CLK	4		/* Force clock */
+#define  SSB_CHIPCO_JCTL_EXT_EN		2		/* Enable external targets */
+#define  SSB_CHIPCO_JCTL_EN		1		/* Enable Jtag master */
+#define SSB_CHIPCO_FLASHCTL		0x0040
+#define  SSB_CHIPCO_FLASHCTL_START	0x80000000
+#define  SSB_CHIPCO_FLASHCTL_BUSY	SSB_CHIPCO_FLASHCTL_START
+#define SSB_CHIPCO_FLASHADDR		0x0044
+#define SSB_CHIPCO_FLASHDATA		0x0048
+#define SSB_CHIPCO_BCAST_ADDR		0x0050
+#define SSB_CHIPCO_BCAST_DATA		0x0054
+#define SSB_CHIPCO_GPIOIN		0x0060
+#define SSB_CHIPCO_GPIOOUT		0x0064
+#define SSB_CHIPCO_GPIOOUTEN		0x0068
+#define SSB_CHIPCO_GPIOCTL		0x006C
+#define SSB_CHIPCO_GPIOPOL		0x0070
+#define SSB_CHIPCO_GPIOIRQ		0x0074
+#define SSB_CHIPCO_WATCHDOG		0x0080
+#define SSB_CHIPCO_GPIOTIMER		0x0088		/* LED powersave (corerev >= 16) */
+#define  SSB_CHIPCO_GPIOTIMER_ONTIME_SHIFT	16
+#define SSB_CHIPCO_GPIOTOUTM		0x008C		/* LED powersave (corerev >= 16) */
+#define SSB_CHIPCO_CLOCK_N		0x0090
+#define SSB_CHIPCO_CLOCK_SB		0x0094
+#define SSB_CHIPCO_CLOCK_PCI		0x0098
+#define SSB_CHIPCO_CLOCK_M2		0x009C
+#define SSB_CHIPCO_CLOCK_MIPS		0x00A0
+#define SSB_CHIPCO_CLKDIV		0x00A4		/* Rev >= 3 only */
+#define	 SSB_CHIPCO_CLKDIV_SFLASH	0x0F000000
+#define	 SSB_CHIPCO_CLKDIV_SFLASH_SHIFT	24
+#define	 SSB_CHIPCO_CLKDIV_OTP		0x000F0000
+#define	 SSB_CHIPCO_CLKDIV_OTP_SHIFT	16
+#define	 SSB_CHIPCO_CLKDIV_JTAG		0x00000F00
+#define	 SSB_CHIPCO_CLKDIV_JTAG_SHIFT	8
+#define	 SSB_CHIPCO_CLKDIV_UART		0x000000FF
+#define SSB_CHIPCO_PLLONDELAY		0x00B0		/* Rev >= 4 only */
+#define SSB_CHIPCO_FREFSELDELAY		0x00B4		/* Rev >= 4 only */
+#define SSB_CHIPCO_SLOWCLKCTL		0x00B8		/* 6 <= Rev <= 9 only */
+#define  SSB_CHIPCO_SLOWCLKCTL_SRC	0x00000007	/* slow clock source mask */
+#define	  SSB_CHIPCO_SLOWCLKCTL_SRC_LPO		0x00000000	/* source of slow clock is LPO */
+#define   SSB_CHIPCO_SLOWCLKCTL_SRC_XTAL	0x00000001	/* source of slow clock is crystal */
+#define	  SSB_CHIPCO_SLOECLKCTL_SRC_PCI		0x00000002	/* source of slow clock is PCI */
+#define  SSB_CHIPCO_SLOWCLKCTL_LPOFREQ	0x00000200	/* LPOFreqSel, 1: 160Khz, 0: 32KHz */
+#define  SSB_CHIPCO_SLOWCLKCTL_LPOPD	0x00000400	/* LPOPowerDown, 1: LPO is disabled, 0: LPO is enabled */
+#define  SSB_CHIPCO_SLOWCLKCTL_FSLOW	0x00000800	/* ForceSlowClk, 1: sb/cores running on slow clock, 0: power logic control */
+#define  SSB_CHIPCO_SLOWCLKCTL_IPLL	0x00001000	/* IgnorePllOffReq, 1/0: power logic ignores/honors PLL clock disable requests from core */
+#define  SSB_CHIPCO_SLOWCLKCTL_ENXTAL	0x00002000	/* XtalControlEn, 1/0: power logic does/doesn't disable crystal when appropriate */
+#define  SSB_CHIPCO_SLOWCLKCTL_XTALPU	0x00004000	/* XtalPU (RO), 1/0: crystal running/disabled */
+#define  SSB_CHIPCO_SLOWCLKCTL_CLKDIV	0xFFFF0000	/* ClockDivider (SlowClk = 1/(4+divisor)) */
+#define  SSB_CHIPCO_SLOWCLKCTL_CLKDIV_SHIFT	16
+#define SSB_CHIPCO_SYSCLKCTL		0x00C0		/* Rev >= 3 only */
+#define	 SSB_CHIPCO_SYSCLKCTL_IDLPEN	0x00000001	/* ILPen: Enable Idle Low Power */
+#define	 SSB_CHIPCO_SYSCLKCTL_ALPEN	0x00000002	/* ALPen: Enable Active Low Power */
+#define	 SSB_CHIPCO_SYSCLKCTL_PLLEN	0x00000004	/* ForcePLLOn */
+#define	 SSB_CHIPCO_SYSCLKCTL_FORCEALP	0x00000008	/* Force ALP (or HT if ALPen is not set */
+#define	 SSB_CHIPCO_SYSCLKCTL_FORCEHT	0x00000010	/* Force HT */
+#define  SSB_CHIPCO_SYSCLKCTL_CLKDIV	0xFFFF0000	/* ClkDiv  (ILP = 1/(4+divisor)) */
+#define  SSB_CHIPCO_SYSCLKCTL_CLKDIV_SHIFT	16
+#define SSB_CHIPCO_CLKSTSTR		0x00C4		/* Rev >= 3 only */
+#define SSB_CHIPCO_PCMCIA_CFG		0x0100
+#define SSB_CHIPCO_PCMCIA_MEMWAIT	0x0104
+#define SSB_CHIPCO_PCMCIA_ATTRWAIT	0x0108
+#define SSB_CHIPCO_PCMCIA_IOWAIT	0x010C
+#define SSB_CHIPCO_IDE_CFG		0x0110
+#define SSB_CHIPCO_IDE_MEMWAIT		0x0114
+#define SSB_CHIPCO_IDE_ATTRWAIT		0x0118
+#define SSB_CHIPCO_IDE_IOWAIT		0x011C
+#define SSB_CHIPCO_PROG_CFG		0x0120
+#define SSB_CHIPCO_PROG_WAITCNT		0x0124
+#define SSB_CHIPCO_FLASH_CFG		0x0128
+#define SSB_CHIPCO_FLASH_WAITCNT	0x012C
+#define SSB_CHIPCO_UART0_DATA		0x0300
+#define SSB_CHIPCO_UART0_IMR		0x0304
+#define SSB_CHIPCO_UART0_FCR		0x0308
+#define SSB_CHIPCO_UART0_LCR		0x030C
+#define SSB_CHIPCO_UART0_MCR		0x0310
+#define SSB_CHIPCO_UART0_LSR		0x0314
+#define SSB_CHIPCO_UART0_MSR		0x0318
+#define SSB_CHIPCO_UART0_SCRATCH	0x031C
+#define SSB_CHIPCO_UART1_DATA		0x0400
+#define SSB_CHIPCO_UART1_IMR		0x0404
+#define SSB_CHIPCO_UART1_FCR		0x0408
+#define SSB_CHIPCO_UART1_LCR		0x040C
+#define SSB_CHIPCO_UART1_MCR		0x0410
+#define SSB_CHIPCO_UART1_LSR		0x0414
+#define SSB_CHIPCO_UART1_MSR		0x0418
+#define SSB_CHIPCO_UART1_SCRATCH	0x041C
+
+
+
+/** Clockcontrol masks and values **/
+
+/* SSB_CHIPCO_CLOCK_N */
+#define	SSB_CHIPCO_CLK_N1		0x0000003F	/* n1 control */
+#define	SSB_CHIPCO_CLK_N2		0x00003F00	/* n2 control */
+#define	SSB_CHIPCO_CLK_N2_SHIFT		8
+#define	SSB_CHIPCO_CLK_PLLC		0x000F0000	/* pll control */
+#define	SSB_CHIPCO_CLK_PLLC_SHIFT	16
+
+/* SSB_CHIPCO_CLOCK_SB/PCI/UART */
+#define	SSB_CHIPCO_CLK_M1		0x0000003F	/* m1 control */
+#define	SSB_CHIPCO_CLK_M2		0x00003F00	/* m2 control */
+#define	SSB_CHIPCO_CLK_M2_SHIFT		8
+#define	SSB_CHIPCO_CLK_M3		0x003F0000	/* m3 control */
+#define	SSB_CHIPCO_CLK_M3_SHIFT		16
+#define	SSB_CHIPCO_CLK_MC		0x1F000000	/* mux control */
+#define	SSB_CHIPCO_CLK_MC_SHIFT		24
+
+/* N3M Clock control magic field values */
+#define	SSB_CHIPCO_CLK_F6_2		0x02		/* A factor of 2 in */
+#define	SSB_CHIPCO_CLK_F6_3		0x03		/* 6-bit fields like */
+#define	SSB_CHIPCO_CLK_F6_4		0x05		/* N1, M1 or M3 */
+#define	SSB_CHIPCO_CLK_F6_5		0x09
+#define	SSB_CHIPCO_CLK_F6_6		0x11
+#define	SSB_CHIPCO_CLK_F6_7		0x21
+
+#define	SSB_CHIPCO_CLK_F5_BIAS		5		/* 5-bit fields get this added */
+
+#define	SSB_CHIPCO_CLK_MC_BYPASS	0x08
+#define	SSB_CHIPCO_CLK_MC_M1		0x04
+#define	SSB_CHIPCO_CLK_MC_M1M2		0x02
+#define	SSB_CHIPCO_CLK_MC_M1M2M3	0x01
+#define	SSB_CHIPCO_CLK_MC_M1M3		0x11
+
+/* Type 2 Clock control magic field values */
+#define	SSB_CHIPCO_CLK_T2_BIAS		2		/* n1, n2, m1 & m3 bias */
+#define	SSB_CHIPCO_CLK_T2M2_BIAS	3		/* m2 bias */
+
+#define	SSB_CHIPCO_CLK_T2MC_M1BYP	1
+#define	SSB_CHIPCO_CLK_T2MC_M2BYP	2
+#define	SSB_CHIPCO_CLK_T2MC_M3BYP	4
+
+/* Type 6 Clock control magic field values */
+#define	SSB_CHIPCO_CLK_T6_MMASK		1		/* bits of interest in m */
+#define	SSB_CHIPCO_CLK_T6_M0		120000000	/* sb clock for m = 0 */
+#define	SSB_CHIPCO_CLK_T6_M1		100000000	/* sb clock for m = 1 */
+#define	SSB_CHIPCO_CLK_SB2MIPS_T6(sb)	(2 * (sb))
+
+/* Common clock base */
+#define	SSB_CHIPCO_CLK_BASE1		24000000	/* Half the clock freq */
+#define SSB_CHIPCO_CLK_BASE2		12500000	/* Alternate crystal on some PLL's */
+
+/* Clock control values for 200Mhz in 5350 */
+#define	SSB_CHIPCO_CLK_5350_N		0x0311
+#define	SSB_CHIPCO_CLK_5350_M		0x04020009
+
+
+/** Bits in the config registers **/
+
+#define	SSB_CHIPCO_CFG_EN		0x0001		/* Enable */
+#define	SSB_CHIPCO_CFG_EXTM		0x000E		/* Extif Mode */
+#define	 SSB_CHIPCO_CFG_EXTM_ASYNC	0x0002		/* Async/Parallel flash */
+#define	 SSB_CHIPCO_CFG_EXTM_SYNC	0x0004		/* Synchronous */
+#define	 SSB_CHIPCO_CFG_EXTM_PCMCIA	0x0008		/* PCMCIA */
+#define	 SSB_CHIPCO_CFG_EXTM_IDE	0x000A		/* IDE */
+#define	SSB_CHIPCO_CFG_DS16		0x0010		/* Data size, 0=8bit, 1=16bit */
+#define	SSB_CHIPCO_CFG_CLKDIV		0x0060		/* Sync: Clock divisor */
+#define	SSB_CHIPCO_CFG_CLKEN		0x0080		/* Sync: Clock enable */
+#define	SSB_CHIPCO_CFG_BSTRO		0x0100		/* Sync: Size/Bytestrobe */
+
+
+/** Flash-specific control/status values */
+
+/* flashcontrol opcodes for ST flashes */
+#define SSB_CHIPCO_FLASHCTL_ST_WREN	0x0006		/* Write Enable */
+#define SSB_CHIPCO_FLASHCTL_ST_WRDIS	0x0004		/* Write Disable */
+#define SSB_CHIPCO_FLASHCTL_ST_RDSR	0x0105		/* Read Status Register */
+#define SSB_CHIPCO_FLASHCTL_ST_WRSR	0x0101		/* Write Status Register */
+#define SSB_CHIPCO_FLASHCTL_ST_READ	0x0303		/* Read Data Bytes */
+#define SSB_CHIPCO_FLASHCTL_ST_PP	0x0302		/* Page Program */
+#define SSB_CHIPCO_FLASHCTL_ST_SE	0x02D8		/* Sector Erase */
+#define SSB_CHIPCO_FLASHCTL_ST_BE	0x00C7		/* Bulk Erase */
+#define SSB_CHIPCO_FLASHCTL_ST_DP	0x00B9		/* Deep Power-down */
+#define SSB_CHIPCO_FLASHCTL_ST_RSIG	0x03AB		/* Read Electronic Signature */
+
+/* Status register bits for ST flashes */
+#define SSB_CHIPCO_FLASHSTA_ST_WIP	0x01		/* Write In Progress */
+#define SSB_CHIPCO_FLASHSTA_ST_WEL	0x02		/* Write Enable Latch */
+#define SSB_CHIPCO_FLASHSTA_ST_BP	0x1C		/* Block Protect */
+#define SSB_CHIPCO_FLASHSTA_ST_BP_SHIFT	2
+#define SSB_CHIPCO_FLASHSTA_ST_SRWD	0x80		/* Status Register Write Disable */
+
+/* flashcontrol opcodes for Atmel flashes */
+#define SSB_CHIPCO_FLASHCTL_AT_READ		0x07E8
+#define SSB_CHIPCO_FLASHCTL_AT_PAGE_READ	0x07D2
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_READ	/* FIXME */
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_READ	/* FIXME */
+#define SSB_CHIPCO_FLASHCTL_AT_STATUS		0x01D7
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRITE	0x0384
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRITE	0x0387
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_ERASE_PRGM	0x0283	/* Erase program */
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_ERASE_PRGM	0x0286	/* Erase program */
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_PROGRAM	0x0288
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_PROGRAM	0x0289
+#define SSB_CHIPCO_FLASHCTL_AT_PAGE_ERASE	0x0281
+#define SSB_CHIPCO_FLASHCTL_AT_BLOCK_ERASE	0x0250
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRER_PRGM	0x0382	/* Write erase program */
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRER_PRGM	0x0385	/* Write erase program */
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_LOAD	0x0253
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_LOAD	0x0255
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_COMPARE	0x0260
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_COMPARE	0x0261
+#define SSB_CHIPCO_FLASHCTL_AT_BUF1_REPROGRAM	0x0258
+#define SSB_CHIPCO_FLASHCTL_AT_BUF2_REPROGRAM	0x0259
+
+/* Status register bits for Atmel flashes */
+#define SSB_CHIPCO_FLASHSTA_AT_READY	0x80
+#define SSB_CHIPCO_FLASHSTA_AT_MISMATCH	0x40
+#define SSB_CHIPCO_FLASHSTA_AT_ID	0x38
+#define SSB_CHIPCO_FLASHSTA_AT_ID_SHIFT	3
+
+
+/** OTP **/
+
+/* OTP regions */
+#define	SSB_CHIPCO_OTP_HW_REGION	SSB_CHIPCO_OTPS_HW_PROTECT
+#define	SSB_CHIPCO_OTP_SW_REGION	SSB_CHIPCO_OTPS_SW_PROTECT
+#define	SSB_CHIPCO_OTP_CID_REGION	SSB_CHIPCO_OTPS_CID_PROTECT
+
+/* OTP regions (Byte offsets from otp size) */
+#define	SSB_CHIPCO_OTP_SWLIM_OFF	(-8)
+#define	SSB_CHIPCO_OTP_CIDBASE_OFF	0
+#define	SSB_CHIPCO_OTP_CIDLIM_OFF	8
+
+/* Predefined OTP words (Word offset from otp size) */
+#define	SSB_CHIPCO_OTP_BOUNDARY_OFF	(-4)
+#define	SSB_CHIPCO_OTP_HWSIGN_OFF	(-3)
+#define	SSB_CHIPCO_OTP_SWSIGN_OFF	(-2)
+#define	SSB_CHIPCO_OTP_CIDSIGN_OFF	(-1)
+
+#define	SSB_CHIPCO_OTP_CID_OFF		0
+#define	SSB_CHIPCO_OTP_PKG_OFF		1
+#define	SSB_CHIPCO_OTP_FID_OFF		2
+#define	SSB_CHIPCO_OTP_RSV_OFF		3
+#define	SSB_CHIPCO_OTP_LIM_OFF		4
+
+#define	SSB_CHIPCO_OTP_SIGNATURE	0x578A
+#define	SSB_CHIPCO_OTP_MAGIC		0x4E56
+
+
+struct ssb_device;
+struct ssb_serial_port;
+
+struct ssb_chipcommon {
+	struct ssb_device *dev;
+	u32 capabilities;
+	/* Fast Powerup Delay constant */
+	u16 fast_pwrup_delay;
+};
+
+extern void ssb_chipcommon_init(struct ssb_chipcommon *cc);
+
+#include <linux/pm.h>
+extern void ssb_chipco_suspend(struct ssb_chipcommon *cc, pm_message_t state);
+extern void ssb_chipco_resume(struct ssb_chipcommon *cc);
+
+extern void ssb_chipco_get_clockcpu(struct ssb_chipcommon *cc,
+                                    u32 *plltype, u32 *n, u32 *m);
+extern void ssb_chipco_get_clockcontrol(struct ssb_chipcommon *cc,
+					u32 *plltype, u32 *n, u32 *m);
+extern void ssb_chipco_timing_init(struct ssb_chipcommon *cc,
+				   unsigned long ns_per_cycle);
+
+enum ssb_clkmode {
+	SSB_CLKMODE_SLOW,
+	SSB_CLKMODE_FAST,
+	SSB_CLKMODE_DYNAMIC,
+};
+
+extern void ssb_chipco_set_clockmode(struct ssb_chipcommon *cc,
+				     enum ssb_clkmode mode);
+
+extern void ssb_chipco_watchdog_timer_set(struct ssb_chipcommon *cc,
+					  u32 ticks);
+
+u32 ssb_chipco_gpio_in(struct ssb_chipcommon *cc, u32 mask);
+
+void ssb_chipco_gpio_out(struct ssb_chipcommon *cc, u32 mask, u32 value);
+
+void ssb_chipco_gpio_outen(struct ssb_chipcommon *cc, u32 mask, u32 value);
+
+#ifdef CONFIG_SSB_SERIAL
+extern int ssb_chipco_serial_init(struct ssb_chipcommon *cc,
+				  struct ssb_serial_port *ports);
+#endif /* CONFIG_SSB_SERIAL */
+
+#endif /* LINUX_SSB_CHIPCO_H_ */
diff --git a/include/linux/ssb/ssb_driver_extif.h b/include/linux/ssb/ssb_driver_extif.h
new file mode 100644
index 00000000000..a9164357b5a
--- /dev/null
+++ b/include/linux/ssb/ssb_driver_extif.h
@@ -0,0 +1,204 @@
+/*
+ * Hardware-specific External Interface I/O core definitions
+ * for the BCM47xx family of SiliconBackplane-based chips.
+ *
+ * The External Interface core supports a total of three external chip selects
+ * supporting external interfaces. One of the external chip selects is
+ * used for Flash, one is used for PCMCIA, and the other may be
+ * programmed to support either a synchronous interface or an
+ * asynchronous interface. The asynchronous interface can be used to
+ * support external devices such as UARTs and the BCM2019 Bluetooth
+ * baseband processor.
+ * The external interface core also contains 2 on-chip 16550 UARTs, clock
+ * frequency control, a watchdog interrupt timer, and a GPIO interface.
+ *
+ * Copyright 2005, Broadcom Corporation
+ * Copyright 2006, Michael Buesch
+ *
+ * Licensed under the GPL version 2. See COPYING for details.
+ */
+#ifndef LINUX_SSB_EXTIFCORE_H_
+#define LINUX_SSB_EXTIFCORE_H_
+
+/* external interface address space */
+#define	SSB_EXTIF_PCMCIA_MEMBASE(x)	(x)
+#define	SSB_EXTIF_PCMCIA_IOBASE(x)	((x) + 0x100000)
+#define	SSB_EXTIF_PCMCIA_CFGBASE(x)	((x) + 0x200000)
+#define	SSB_EXTIF_CFGIF_BASE(x)		((x) + 0x800000)
+#define	SSB_EXTIF_FLASH_BASE(x)		((x) + 0xc00000)
+
+#define SSB_EXTIF_NR_GPIOOUT		5
+/* GPIO NOTE:
+ * The multiple instances of output and output enable registers
+ * are present to allow driver software for multiple cores to control
+ * gpio outputs without needing to share a single register pair.
+ * Use the following helper macro to get a register offset value.
+ */
+#define SSB_EXTIF_GPIO_OUT(index)	({		\
+	BUILD_BUG_ON(index >= SSB_EXTIF_NR_GPIOOUT);	\
+	SSB_EXTIF_GPIO_OUT_BASE + ((index) * 8);	\
+					})
+#define SSB_EXTIF_GPIO_OUTEN(index)	({		\
+	BUILD_BUG_ON(index >= SSB_EXTIF_NR_GPIOOUT);	\
+	SSB_EXTIF_GPIO_OUTEN_BASE + ((index) * 8);	\
+					})
+
+/** EXTIF core registers **/
+
+#define SSB_EXTIF_CTL			0x0000
+#define  SSB_EXTIF_CTL_UARTEN		(1 << 0) /* UART enable */
+#define SSB_EXTIF_EXTSTAT		0x0004
+#define  SSB_EXTIF_EXTSTAT_EMODE	(1 << 0) /* Endian mode (ro) */
+#define  SSB_EXTIF_EXTSTAT_EIRQPIN	(1 << 1) /* External interrupt pin (ro) */
+#define  SSB_EXTIF_EXTSTAT_GPIOIRQPIN	(1 << 2) /* GPIO interrupt pin (ro) */
+#define SSB_EXTIF_PCMCIA_CFG		0x0010
+#define SSB_EXTIF_PCMCIA_MEMWAIT	0x0014
+#define SSB_EXTIF_PCMCIA_ATTRWAIT	0x0018
+#define SSB_EXTIF_PCMCIA_IOWAIT		0x001C
+#define SSB_EXTIF_PROG_CFG		0x0020
+#define SSB_EXTIF_PROG_WAITCNT		0x0024
+#define SSB_EXTIF_FLASH_CFG		0x0028
+#define SSB_EXTIF_FLASH_WAITCNT		0x002C
+#define SSB_EXTIF_WATCHDOG		0x0040
+#define SSB_EXTIF_CLOCK_N		0x0044
+#define SSB_EXTIF_CLOCK_SB		0x0048
+#define SSB_EXTIF_CLOCK_PCI		0x004C
+#define SSB_EXTIF_CLOCK_MII		0x0050
+#define SSB_EXTIF_GPIO_IN		0x0060
+#define SSB_EXTIF_GPIO_OUT_BASE		0x0064
+#define SSB_EXTIF_GPIO_OUTEN_BASE	0x0068
+