diff options
author | David S. Miller <davem@davemloft.net> | 2008-02-29 13:41:25 -0800 |
---|---|---|
committer | David S. Miller <davem@davemloft.net> | 2008-02-29 13:41:25 -0800 |
commit | 4a80f2788952055a627f2093a0174537d70aec1b (patch) | |
tree | 411c8ec555fe85cf9faa9da90e62ab781b33661c /include | |
parent | 03a64c93b68e1eff299b9bbbb0d13105171cddc4 (diff) | |
parent | e4861829072c61883114c64a3af61f305a789ff0 (diff) |
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/linville/wireless-2.6.26
Diffstat (limited to 'include')
-rw-r--r-- | include/linux/nl80211.h | 99 | ||||
-rw-r--r-- | include/linux/ssb/ssb.h | 10 | ||||
-rw-r--r-- | include/linux/ssb/ssb_driver_chipcommon.h | 4 | ||||
-rw-r--r-- | include/net/cfg80211.h | 24 | ||||
-rw-r--r-- | include/net/mac80211.h | 384 | ||||
-rw-r--r-- | include/net/wireless.h | 168 |
6 files changed, 497 insertions, 192 deletions
diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h index 9fecf902419..a9f0b93324a 100644 --- a/include/linux/nl80211.h +++ b/include/linux/nl80211.h @@ -161,6 +161,12 @@ enum nl80211_commands { * given for %NL80211_CMD_GET_STATION, nested attribute containing * info as possible, see &enum nl80211_sta_stats. * + * @NL80211_ATTR_WIPHY_BANDS: Information about an operating bands, + * consisting of a nested array. + * + * @NL80211_ATTR_MNTR_FLAGS: flags, nested element with NLA_FLAG attributes of + * &enum nl80211_mntr_flags. + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ @@ -195,6 +201,10 @@ enum nl80211_attrs { NL80211_ATTR_STA_VLAN, NL80211_ATTR_STA_STATS, + NL80211_ATTR_WIPHY_BANDS, + + NL80211_ATTR_MNTR_FLAGS, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -280,4 +290,93 @@ enum nl80211_sta_stats { NL80211_STA_STAT_MAX = __NL80211_STA_STAT_AFTER_LAST - 1 }; +/** + * enum nl80211_band_attr - band attributes + * @__NL80211_BAND_ATTR_INVALID: attribute number 0 is reserved + * @NL80211_BAND_ATTR_FREQS: supported frequencies in this band, + * an array of nested frequency attributes + * @NL80211_BAND_ATTR_RATES: supported bitrates in this band, + * an array of nested bitrate attributes + */ +enum nl80211_band_attr { + __NL80211_BAND_ATTR_INVALID, + NL80211_BAND_ATTR_FREQS, + NL80211_BAND_ATTR_RATES, + + /* keep last */ + __NL80211_BAND_ATTR_AFTER_LAST, + NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1 +}; + +/** + * enum nl80211_frequency_attr - frequency attributes + * @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz + * @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current + * regulatory domain. + * @NL80211_FREQUENCY_ATTR_PASSIVE_SCAN: Only passive scanning is + * permitted on this channel in current regulatory domain. + * @NL80211_FREQUENCY_ATTR_NO_IBSS: IBSS networks are not permitted + * on this channel in current regulatory domain. + * @NL80211_FREQUENCY_ATTR_RADAR: Radar detection is mandatory + * on this channel in current regulatory domain. + */ +enum nl80211_frequency_attr { + __NL80211_FREQUENCY_ATTR_INVALID, + NL80211_FREQUENCY_ATTR_FREQ, + NL80211_FREQUENCY_ATTR_DISABLED, + NL80211_FREQUENCY_ATTR_PASSIVE_SCAN, + NL80211_FREQUENCY_ATTR_NO_IBSS, + NL80211_FREQUENCY_ATTR_RADAR, + + /* keep last */ + __NL80211_FREQUENCY_ATTR_AFTER_LAST, + NL80211_FREQUENCY_ATTR_MAX = __NL80211_FREQUENCY_ATTR_AFTER_LAST - 1 +}; + +/** + * enum nl80211_bitrate_attr - bitrate attributes + * @NL80211_BITRATE_ATTR_RATE: Bitrate in units of 100 kbps + * @NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE: Short preamble supported + * in 2.4 GHz band. + */ +enum nl80211_bitrate_attr { + __NL80211_BITRATE_ATTR_INVALID, + NL80211_BITRATE_ATTR_RATE, + NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE, + + /* keep last */ + __NL80211_BITRATE_ATTR_AFTER_LAST, + NL80211_BITRATE_ATTR_MAX = __NL80211_BITRATE_ATTR_AFTER_LAST - 1 +}; + +/** + * enum nl80211_mntr_flags - monitor configuration flags + * + * Monitor configuration flags. + * + * @__NL80211_MNTR_FLAG_INVALID: reserved + * + * @NL80211_MNTR_FLAG_FCSFAIL: pass frames with bad FCS + * @NL80211_MNTR_FLAG_PLCPFAIL: pass frames with bad PLCP + * @NL80211_MNTR_FLAG_CONTROL: pass control frames + * @NL80211_MNTR_FLAG_OTHER_BSS: disable BSSID filtering + * @NL80211_MNTR_FLAG_COOK_FRAMES: report frames after processing. + * overrides all other flags. + * + * @__NL80211_MNTR_FLAG_AFTER_LAST: internal use + * @NL80211_MNTR_FLAG_MAX: highest possible monitor flag + */ +enum nl80211_mntr_flags { + __NL80211_MNTR_FLAG_INVALID, + NL80211_MNTR_FLAG_FCSFAIL, + NL80211_MNTR_FLAG_PLCPFAIL, + NL80211_MNTR_FLAG_CONTROL, + NL80211_MNTR_FLAG_OTHER_BSS, + NL80211_MNTR_FLAG_COOK_FRAMES, + + /* keep last */ + __NL80211_MNTR_FLAG_AFTER_LAST, + NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1 +}; + #endif /* __LINUX_NL80211_H */ diff --git a/include/linux/ssb/ssb.h b/include/linux/ssb/ssb.h index 20add65215a..860d28c6d14 100644 --- a/include/linux/ssb/ssb.h +++ b/include/linux/ssb/ssb.h @@ -72,8 +72,10 @@ struct ssb_device; /* Lowlevel read/write operations on the device MMIO. * Internal, don't use that outside of ssb. */ struct ssb_bus_ops { + u8 (*read8)(struct ssb_device *dev, u16 offset); u16 (*read16)(struct ssb_device *dev, u16 offset); u32 (*read32)(struct ssb_device *dev, u16 offset); + void (*write8)(struct ssb_device *dev, u16 offset, u8 value); void (*write16)(struct ssb_device *dev, u16 offset, u16 value); void (*write32)(struct ssb_device *dev, u16 offset, u32 value); }; @@ -344,6 +346,10 @@ void ssb_device_disable(struct ssb_device *dev, u32 core_specific_flags); /* Device MMIO register read/write functions. */ +static inline u8 ssb_read8(struct ssb_device *dev, u16 offset) +{ + return dev->ops->read8(dev, offset); +} static inline u16 ssb_read16(struct ssb_device *dev, u16 offset) { return dev->ops->read16(dev, offset); @@ -352,6 +358,10 @@ static inline u32 ssb_read32(struct ssb_device *dev, u16 offset) { return dev->ops->read32(dev, offset); } +static inline void ssb_write8(struct ssb_device *dev, u16 offset, u8 value) +{ + dev->ops->write8(dev, offset, value); +} static inline void ssb_write16(struct ssb_device *dev, u16 offset, u16 value) { dev->ops->write16(dev, offset, value); diff --git a/include/linux/ssb/ssb_driver_chipcommon.h b/include/linux/ssb/ssb_driver_chipcommon.h index 536851b946f..b548a54ff1f 100644 --- a/include/linux/ssb/ssb_driver_chipcommon.h +++ b/include/linux/ssb/ssb_driver_chipcommon.h @@ -390,6 +390,10 @@ extern void ssb_chipco_set_clockmode(struct ssb_chipcommon *cc, extern void ssb_chipco_watchdog_timer_set(struct ssb_chipcommon *cc, u32 ticks); +void ssb_chipco_irq_mask(struct ssb_chipcommon *cc, u32 mask, u32 value); + +u32 ssb_chipco_irq_status(struct ssb_chipcommon *cc, u32 mask); + /* Chipcommon GPIO pin access. */ u32 ssb_chipco_gpio_in(struct ssb_chipcommon *cc, u32 mask); u32 ssb_chipco_gpio_out(struct ssb_chipcommon *cc, u32 mask, u32 value); diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index bcc480b8892..ab4caf63954 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -163,6 +163,26 @@ struct station_stats { u32 tx_bytes; }; +/** + * enum monitor_flags - monitor flags + * + * Monitor interface configuration flags. Note that these must be the bits + * according to the nl80211 flags. + * + * @MONITOR_FLAG_FCSFAIL: pass frames with bad FCS + * @MONITOR_FLAG_PLCPFAIL: pass frames with bad PLCP + * @MONITOR_FLAG_CONTROL: pass control frames + * @MONITOR_FLAG_OTHER_BSS: disable BSSID filtering + * @MONITOR_FLAG_COOK_FRAMES: report frames after processing + */ +enum monitor_flags { + MONITOR_FLAG_FCSFAIL = 1<<NL80211_MNTR_FLAG_FCSFAIL, + MONITOR_FLAG_PLCPFAIL = 1<<NL80211_MNTR_FLAG_PLCPFAIL, + MONITOR_FLAG_CONTROL = 1<<NL80211_MNTR_FLAG_CONTROL, + MONITOR_FLAG_OTHER_BSS = 1<<NL80211_MNTR_FLAG_OTHER_BSS, + MONITOR_FLAG_COOK_FRAMES = 1<<NL80211_MNTR_FLAG_COOK_FRAMES, +}; + /* from net/wireless.h */ struct wiphy; @@ -213,10 +233,10 @@ struct wiphy; */ struct cfg80211_ops { int (*add_virtual_intf)(struct wiphy *wiphy, char *name, - enum nl80211_iftype type); + enum nl80211_iftype type, u32 *flags); int (*del_virtual_intf)(struct wiphy *wiphy, int ifindex); int (*change_virtual_intf)(struct wiphy *wiphy, int ifindex, - enum nl80211_iftype type); + enum nl80211_iftype type, u32 *flags); int (*add_key)(struct wiphy *wiphy, struct net_device *netdev, u8 key_index, u8 *mac_addr, diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 9083bafb63c..7a80c398123 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -38,7 +38,11 @@ * called in hardware interrupt context. The low-level driver must not call any * other functions in hardware interrupt context. If there is a need for such * call, the low-level driver should first ACK the interrupt and perform the - * IEEE 802.11 code call after this, e.g. from a scheduled workqueue function. + * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even + * tasklet function. + * + * NOTE: If the driver opts to use the _irqsafe() functions, it may not also + * use the non-irqsafe functions! */ /** @@ -69,95 +73,6 @@ * not do so then mac80211 may add this under certain circumstances. */ -#define IEEE80211_CHAN_W_SCAN 0x00000001 -#define IEEE80211_CHAN_W_ACTIVE_SCAN 0x00000002 -#define IEEE80211_CHAN_W_IBSS 0x00000004 - -/* Channel information structure. Low-level driver is expected to fill in chan, - * freq, and val fields. Other fields will be filled in by 80211.o based on - * hostapd information and low-level driver does not need to use them. The - * limits for each channel will be provided in 'struct ieee80211_conf' when - * configuring the low-level driver with hw->config callback. If a device has - * a default regulatory domain, IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED - * can be set to let the driver configure all fields */ -struct ieee80211_channel { - short chan; /* channel number (IEEE 802.11) */ - short freq; /* frequency in MHz */ - int val; /* hw specific value for the channel */ - int flag; /* flag for hostapd use (IEEE80211_CHAN_*) */ - unsigned char power_level; - unsigned char antenna_max; -}; - -#define IEEE80211_RATE_ERP 0x00000001 -#define IEEE80211_RATE_BASIC 0x00000002 -#define IEEE80211_RATE_PREAMBLE2 0x00000004 -#define IEEE80211_RATE_SUPPORTED 0x00000010 -#define IEEE80211_RATE_OFDM 0x00000020 -#define IEEE80211_RATE_CCK 0x00000040 -#define IEEE80211_RATE_MANDATORY 0x00000100 - -#define IEEE80211_RATE_CCK_2 (IEEE80211_RATE_CCK | IEEE80211_RATE_PREAMBLE2) -#define IEEE80211_RATE_MODULATION(f) \ - (f & (IEEE80211_RATE_CCK | IEEE80211_RATE_OFDM)) - -/* Low-level driver should set PREAMBLE2, OFDM and CCK flags. - * BASIC, SUPPORTED, ERP, and MANDATORY flags are set in 80211.o based on the - * configuration. */ -struct ieee80211_rate { - int rate; /* rate in 100 kbps */ - int val; /* hw specific value for the rate */ - int flags; /* IEEE80211_RATE_ flags */ - int val2; /* hw specific value for the rate when using short preamble - * (only when IEEE80211_RATE_PREAMBLE2 flag is set, i.e., for - * 2, 5.5, and 11 Mbps) */ - signed char min_rssi_ack; - unsigned char min_rssi_ack_delta; - - /* following fields are set by 80211.o and need not be filled by the - * low-level driver */ - int rate_inv; /* inverse of the rate (LCM(all rates) / rate) for - * optimizing channel utilization estimates */ -}; - -/** - * enum ieee80211_phymode - PHY modes - * - * @MODE_IEEE80211A: 5GHz as defined by 802.11a/802.11h - * @MODE_IEEE80211B: 2.4 GHz as defined by 802.11b - * @MODE_IEEE80211G: 2.4 GHz as defined by 802.11g (with OFDM), - * backwards compatible with 11b mode - * @NUM_IEEE80211_MODES: internal - */ -enum ieee80211_phymode { - MODE_IEEE80211A, - MODE_IEEE80211B, - MODE_IEEE80211G, - - /* keep last */ - NUM_IEEE80211_MODES -}; - -/** - * struct ieee80211_ht_info - describing STA's HT capabilities - * - * This structure describes most essential parameters needed - * to describe 802.11n HT capabilities for an STA. - * - * @ht_supported: is HT supported by STA, 0: no, 1: yes - * @cap: HT capabilities map as described in 802.11n spec - * @ampdu_factor: Maximum A-MPDU length factor - * @ampdu_density: Minimum A-MPDU spacing - * @supp_mcs_set: Supported MCS set as described in 802.11n spec - */ -struct ieee80211_ht_info { - u8 ht_supported; - u16 cap; /* use IEEE80211_HT_CAP_ */ - u8 ampdu_factor; - u8 ampdu_density; - u8 supp_mcs_set[16]; -}; - /** * struct ieee80211_ht_bss_info - describing BSS's HT characteristics * @@ -175,46 +90,22 @@ struct ieee80211_ht_bss_info { }; /** - * struct ieee80211_hw_mode - PHY mode definition - * - * This structure describes the capabilities supported by the device - * in a single PHY mode. - * - * @list: internal - * @channels: pointer to array of supported channels - * @rates: pointer to array of supported bitrates - * @mode: the PHY mode for this definition - * @num_channels: number of supported channels - * @num_rates: number of supported bitrates - * @ht_info: PHY's 802.11n HT abilities for this mode - */ -struct ieee80211_hw_mode { - struct list_head list; - struct ieee80211_channel *channels; - struct ieee80211_rate *rates; - enum ieee80211_phymode mode; - int num_channels; - int num_rates; - struct ieee80211_ht_info ht_info; -}; - -/** * struct ieee80211_tx_queue_params - transmit queue configuration * * The information provided in this structure is required for QoS - * transmit queue configuration. + * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29. * * @aifs: arbitration interface space [0..255, -1: use default] * @cw_min: minimum contention window [will be a value of the form * 2^n-1 in the range 1..1023; 0: use default] * @cw_max: maximum contention window [like @cw_min] - * @burst_time: maximum burst time in units of 0.1ms, 0 meaning disabled + * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled */ struct ieee80211_tx_queue_params { - int aifs; - int cw_min; - int cw_max; - int burst_time; + s16 aifs; + u16 cw_min; + u16 cw_max; + u16 txop; }; /** @@ -246,6 +137,7 @@ struct ieee80211_tx_queue_stats_data { * @IEEE80211_TX_QUEUE_AFTER_BEACON: transmit queue for frames to be * sent after a beacon * @IEEE80211_TX_QUEUE_BEACON: transmit queue for beacon frames + * @NUM_TX_DATA_QUEUES_AMPDU: adding more queues for A-MPDU */ enum ieee80211_tx_queue { IEEE80211_TX_QUEUE_DATA0, @@ -261,11 +153,12 @@ enum ieee80211_tx_queue { * this struct need to have fixed values. As soon as it is removed, we can * fix these entries. */ IEEE80211_TX_QUEUE_AFTER_BEACON = 6, - IEEE80211_TX_QUEUE_BEACON = 7 + IEEE80211_TX_QUEUE_BEACON = 7, + NUM_TX_DATA_QUEUES_AMPDU = 16 }; struct ieee80211_tx_queue_stats { - struct ieee80211_tx_queue_stats_data data[NUM_TX_DATA_QUEUES]; + struct ieee80211_tx_queue_stats_data data[NUM_TX_DATA_QUEUES_AMPDU]; }; struct ieee80211_low_level_stats { @@ -318,11 +211,13 @@ struct ieee80211_bss_conf { struct ieee80211_tx_control { struct ieee80211_vif *vif; - int tx_rate; /* Transmit rate, given as the hw specific value for the - * rate (from struct ieee80211_rate) */ - int rts_cts_rate; /* Transmit rate for RTS/CTS frame, given as the hw - * specific value for the rate (from - * struct ieee80211_rate) */ + struct ieee80211_rate *tx_rate; + + /* Transmit rate for RTS/CTS frame */ + struct ieee80211_rate *rts_cts_rate; + + /* retry rate for the last retries */ + struct ieee80211_rate *alt_retry_rate; #define IEEE80211_TXCTL_REQ_TX_STATUS (1<<0)/* request TX status callback for * this frame */ @@ -337,10 +232,12 @@ struct ieee80211_tx_control { #define IEEE80211_TXCTL_NO_ACK (1<<4) /* tell the low level not to * wait for an ack */ #define IEEE80211_TXCTL_RATE_CTRL_PROBE (1<<5) -#define IEEE80211_TXCTL_CLEAR_DST_MASK (1<<6) +#define IEEE80211_TXCTL_CLEAR_PS_FILT (1<<6) /* clear powersave filter + * for destination station */ #define IEEE80211_TXCTL_REQUEUE (1<<7) #define IEEE80211_TXCTL_FIRST_FRAGMENT (1<<8) /* this is a first fragment of * the frame */ +#define IEEE80211_TXCTL_SHORT_PREAMBLE (1<<9) #define IEEE80211_TXCTL_LONG_RETRY_LIMIT (1<<10) /* this frame should be send * using the through * set_retry_limit configured @@ -348,6 +245,8 @@ struct ieee80211_tx_control { #define IEEE80211_TXCTL_EAPOL_FRAME (1<<11) /* internal to mac80211 */ #define IEEE80211_TXCTL_SEND_AFTER_DTIM (1<<12) /* send this frame after DTIM * beacon */ +#define IEEE80211_TXCTL_AMPDU (1<<13) /* this frame should be sent + * as part of an A-MPDU */ u32 flags; /* tx control flags defined * above */ u8 key_idx; /* keyidx from hw->set_key(), undefined if @@ -355,20 +254,11 @@ struct ieee80211_tx_control { u8 retry_limit; /* 1 = only first attempt, 2 = one retry, .. * This could be used when set_retry_limit * is not implemented by the driver */ - u8 power_level; /* per-packet transmit power level, in dBm */ u8 antenna_sel_tx; /* 0 = default/diversity, 1 = Ant0, 2 = Ant1 */ u8 icv_len; /* length of the ICV/MIC field in octets */ u8 iv_len; /* length of the IV field in octets */ u8 queue; /* hardware queue to use for this frame; * 0 = highest, hw->queues-1 = lowest */ - struct ieee80211_rate *rate; /* internal 80211.o rate */ - struct ieee80211_rate *rts_rate; /* internal 80211.o rate - * for RTS/CTS */ - int alt_retry_rate; /* retry rate for the last retries, given as the - * hw specific value for the rate (from - * struct ieee80211_rate). To be used to limit - * packet dropping when probing higher rates, if hw - * supports multiple retry rates. -1 = not used */ int type; /* internal */ }; @@ -391,7 +281,8 @@ struct ieee80211_tx_control { * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on * the frame. * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field) - * is valid. + * is valid. This is useful in monitor mode and necessary for beacon frames + * to enable IBSS merging. */ enum mac80211_rx_flags { RX_FLAG_MMIC_ERROR = 1<<0, @@ -410,27 +301,26 @@ enum mac80211_rx_flags { * The low-level driver should provide this information (the subset * supported by hardware) to the 802.11 code with each received * frame. - * @mactime: MAC timestamp as defined by 802.11 + * @mactime: value in microseconds of the 64-bit Time Synchronization Function + * (TSF) timer when the first data symbol (MPDU) arrived at the hardware. + * @band: the active band when this frame was received * @freq: frequency the radio was tuned to when receiving this frame, in MHz - * @channel: channel the radio was tuned to - * @phymode: active PHY mode * @ssi: signal strength when receiving this frame * @signal: used as 'qual' in statistics reporting * @noise: PHY noise when receiving this frame * @antenna: antenna used - * @rate: data rate + * @rate_idx: index of data rate into band's supported rates * @flag: %RX_FLAG_* */ struct ieee80211_rx_status { u64 mactime; + enum ieee80211_band band; int freq; - int channel; - enum ieee80211_phymode phymode; int ssi; int signal; int noise; int antenna; - int rate; + int rate_idx; int flag; }; @@ -441,12 +331,14 @@ struct ieee80211_rx_status { * * @IEEE80211_TX_STATUS_TX_FILTERED: The frame was not transmitted * because the destination STA was in powersave mode. - * * @IEEE80211_TX_STATUS_ACK: Frame was acknowledged + * @IEEE80211_TX_STATUS_AMPDU: The frame was aggregated, so status + * is for the whole aggregation. */ enum ieee80211_tx_status_flags { IEEE80211_TX_STATUS_TX_FILTERED = 1<<0, IEEE80211_TX_STATUS_ACK = 1<<1, + IEEE80211_TX_STATUS_AMPDU = 1<<2, }; /** @@ -457,24 +349,25 @@ enum ieee80211_tx_status_flags { * * @control: a copy of the &struct ieee80211_tx_control passed to the driver * in the tx() callback. - * * @flags: transmit status flags, defined above - * - * @ack_signal: signal strength of the ACK frame - * + * @retry_count: number of retries * @excessive_retries: set to 1 if the frame was retried many times * but not acknowledged - * - * @retry_count: number of retries - * + * @ampdu_ack_len: number of aggregated frames. + * relevant only if IEEE80211_TX_STATUS_AMPDU was set. + * @ampdu_ack_map: block ack bit map for the aggregation. + * relevant only if IEEE80211_TX_STATUS_AMPDU was set. + * @ack_signal: signal strength of the ACK frame * @queue_length: ?? REMOVE * @queue_number: ?? REMOVE */ struct ieee80211_tx_status { struct ieee80211_tx_control control; u8 flags; - bool excessive_retries; u8 retry_count; + bool excessive_retries; + u8 ampdu_ack_len; + u64 ampdu_ack_map; int ack_signal; int queue_length; int queue_number; @@ -502,41 +395,30 @@ enum ieee80211_conf_flags { * * @radio_enabled: when zero, driver is required to switch off the radio. * TODO make a flag - * @channel: IEEE 802.11 channel number - * @freq: frequency in MHz - * @channel_val: hardware specific channel value for the channel - * @phymode: PHY mode to activate (REMOVE) - * @chan: channel to switch to, pointer to the channel information - * @mode: pointer to mode definition - * @regulatory_domain: ?? * @beacon_int: beacon interval (TODO make interface config) * @flags: configuration flags defined above - * @power_level: transmit power limit for current regulatory domain in dBm - * @antenna_max: maximum antenna gain + * @power_level: requested transmit power (in dBm) + * @max_antenna_gain: maximum antenna gain (in dBi) * @antenna_sel_tx: transmit antenna selection, 0: default/diversity, * 1/2: antenna 0/1 * @antenna_sel_rx: receive antenna selection, like @antenna_sel_tx * @ht_conf: describes current self configuration of 802.11n HT capabilies * @ht_bss_conf: describes current BSS configuration of 802.11n HT parameters + * @channel: the channel to tune to */ struct ieee80211_conf { - int channel; /* IEEE 802.11 channel number */ - int freq; /* MHz */ - int channel_val; /* hw specific value for the channel */ - - enum ieee80211_phymode phymode; - struct ieee80211_channel *chan; - struct ieee80211_hw_mode *mode; unsigned int regulatory_domain; int radio_enabled; int beacon_int; u32 flags; - u8 power_level; - u8 antenna_max; + int power_level; + int max_antenna_gain; u8 antenna_sel_tx; u8 antenna_sel_rx; + struct ieee80211_channel *channel; + struct ieee80211_ht_info ht_conf; struct ieee80211_ht_bss_info ht_bss_conf; }; @@ -757,15 +639,19 @@ enum sta_notify_cmd { * %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because * otherwise the stack will not know when the DTIM beacon was sent. * - * @IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED: - * Channels are already configured to the default regulatory domain - * specified in the device's EEPROM + * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE: + * Hardware is not capable of short slot operation on the 2.4 GHz band. + * + * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE: + * Hardware is not capable of receiving frames with short preamble on + * the 2.4 GHz band. */ enum ieee80211_hw_flags { IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE = 1<<0, IEEE80211_HW_RX_INCLUDES_FCS = 1<<1, IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2, - IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED = 1<<3, + IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3, + IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4, }; /** @@ -777,7 +663,8 @@ enum ieee80211_hw_flags { * @wiphy: This points to the &struct wiphy allocated for this * 802.11 PHY. You must fill in the @perm_addr and @dev * members of this structure using SET_IEEE80211_DEV() - * and SET_IEEE80211_PERM_ADDR(). + * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported + * bands (with channels, bitrates) are registered here. * * @conf: &struct ieee80211_conf, device configuration, don't use. * @@ -913,8 +800,18 @@ static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr) * parameter to see whether multicast frames should be accepted * or dropped. * - * All unsupported flags in @total_flags must be cleared, i.e. you - * should clear all bits except those you honoured. + * All unsupported flags in @total_flags must be cleared. + * Hardware does not support a flag if it is incapable of _passing_ + * the frame to the stack. Otherwise the driver must ignore + * the flag, but not clear it. + * You must _only_ clear the flag (announce no support for the + * flag to mac80211) if you are not able to pass the packet type + * to the stack (so the hardware always filters it). + * So for example, you should clear @FIF_CONTROL, if your hardware + * always filters control frames. If your hardware always passes + * control frames to the kernel and is incapable of filtering them, + * you do _not_ clear the @FIF_CONTROL flag. + * This rule applies to all other FIF flags as well. */ /** @@ -967,10 +864,14 @@ enum ieee80211_filter_flags { * &struct ieee80211_ops to indicate which action is needed. * @IEEE80211_AMPDU_RX_START: start Rx aggregation * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation + * @IEEE80211_AMPDU_TX_START: start Tx aggregation + * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation */ enum ieee80211_ampdu_mlme_action { IEEE80211_AMPDU_RX_START, IEEE80211_AMPDU_RX_STOP, + IEEE80211_AMPDU_TX_START, + IEEE80211_AMPDU_TX_STOP, }; /** @@ -1051,7 +952,9 @@ enum ieee80211_ampdu_mlme_action { * given local_address is enabled. * * @hw_scan: Ask the hardware to service the scan request, no need to start - * the scan state machine in stack. + * the scan state machine in stack. The scan must honour the channel + * configuration done by the regulatory agent in the wiphy's registered + * bands. * * @get_stats: return low-level statistics * @@ -1111,7 +1014,8 @@ enum ieee80211_ampdu_mlme_action { * The RA/TID combination determines the destination and TID we want * the ampdu action to be performed for. The action is defined through * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn) - * is the first frame we expect to perform the action on. + * is the first frame we expect to perform the action on. notice + * that TX/RX_STOP can pass NULL for this parameter. */ struct ieee80211_ops { int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb, @@ -1162,7 +1066,7 @@ struct ieee80211_ops { int (*conf_ht)(struct ieee80211_hw *hw, struct ieee80211_conf *conf); int (*ampdu_action)(struct ieee80211_hw *hw, enum ieee80211_ampdu_mlme_action action, - const u8 *ra, u16 tid, u16 ssn); + const u8 *addr, u16 tid, u16 *ssn); }; /** @@ -1272,10 +1176,6 @@ static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) #endif } -/* Register a new hardware PHYMODE capability to the stack. */ -int ieee80211_register_hwmode(struct ieee80211_hw *hw, - struct ieee80211_hw_mode *mode); - /** * ieee80211_unregister_hw - Unregister a hardware device * @@ -1308,7 +1208,10 @@ void __ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb, * buffer in @skb must start with an IEEE 802.11 header or a radiotap * header if %RX_FLAG_RADIOTAP is set in the @status flags. * - * This function may not be called in IRQ context. + * This function may not be called in IRQ context. Calls to this function + * for a single hardware must be synchronized against each other. Calls + * to this function and ieee80211_rx_irqsafe() may not be mixed for a + * single hardware. * * @hw: the hardware this frame came in on * @skb: the buffer to receive, owned by mac80211 after this call @@ -1325,7 +1228,10 @@ static inline void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb, * ieee80211_rx_irqsafe - receive frame * * Like ieee80211_rx() but can be called in IRQ context - * (internally defers to a workqueue.) + * (internally defers to a tasklet.) + * + * Calls to this function and ieee80211_rx() may not be mixed for a + * single hardware. * * @hw: the hardware this frame came in on * @skb: the buffer to receive, owned by mac80211 after this call @@ -1344,6 +1250,11 @@ void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, * transmitted. It is permissible to not call this function for * multicast frames but this can affect statistics. * + * This function may not be called in IRQ context. Calls to this function + * for a single hardware must be synchronized against each other. Calls + * to this function and ieee80211_tx_status_irqsafe() may not be mixed + * for a single hardware. + * * @hw: the hardware the frame was transmitted by * @skb: the frame that was transmitted, owned by mac80211 after this call * @status: status information for this frame; the status pointer need not @@ -1353,6 +1264,22 @@ void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, void ieee80211_tx_status(struct ieee80211_hw *hw, struct sk_buff *skb, struct ieee80211_tx_status *status); + +/** + * ieee80211_tx_status_irqsafe - irq-safe transmit status callback + * + * Like ieee80211_tx_status() but can be called in IRQ context + * (internally defers to a tasklet.) + * + * Calls to this function and ieee80211_tx_status() may not be mixed for a + * single hardware. + * + * @hw: the hardware the frame was transmitted by + * @skb: the frame that was transmitted, owned by mac80211 after this call + * @status: status information for this frame; the status pointer need not + * be valid after this function returns and is not freed by mac80211, + * it is recommended that it points to a stack area + */ void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb, struct ieee80211_tx_status *status); @@ -1449,7 +1376,7 @@ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, * @hw: pointer obtained from ieee80211_alloc_hw(). * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. * @frame_len: the length of the frame. - * @rate: the rate (in 100kbps) at which the frame is going to be transmitted. + * @rate: the rate at which the frame is going to be transmitted. * * Calculate the duration field of some generic frame, given its * length and transmission rate (in 100kbps). @@ -1457,7 +1384,7 @@ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, struct ieee80211_vif *vif, size_t frame_len, - int rate); + struct ieee80211_rate *rate); /** * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames @@ -1574,4 +1501,81 @@ void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, struct ieee80211_vif *vif), void *data); +/** + * ieee80211_start_tx_ba_session - Start a tx Block Ack session. + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * @ra: receiver address of the BA session recipient + * @tid: the TID to BA on. + * @return: success if addBA request was sent, failure otherwise + * + * Although mac80211/low level driver/user space application can estimate + * the need to start aggregation on a certain RA/TID, the session level + * will be managed by the mac80211. + */ +int ieee80211_start_tx_ba_session(struct ieee80211_hw *hw, u8 *ra, u16 tid); + +/** + * ieee80211_start_tx_ba_cb - low level driver ready to aggregate. + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * @ra: receiver address of the BA session recipient. + * @tid: the TID to BA on. + * + * This function must be called by low level driver once it has + * finished with preparations for the BA session. + */ +void ieee80211_start_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u16 tid); + +/** + * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate. + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * @ra: receiver address of the BA session recipient. + * @tid: the TID to BA on. + * + * This function must be called by low level driver once it has + * finished with preparations for the BA session. + * This version of the function is irq safe. + */ +void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra, + u16 tid); + +/** + * ieee80211_stop_tx_ba_session - Stop a Block Ack session. + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * @ra: receiver address of the BA session recipient + * @tid: the TID to stop BA. + * @initiator: if indicates initiator DELBA frame will be sent. + * @return: error if no sta with matching da found, success otherwise + * + * Although mac80211/low level driver/user space application can estimate + * the need to stop aggregation on a certain RA/TID, the session level + * will be managed by the mac80211. + */ +int ieee80211_stop_tx_ba_session(struct ieee80211_hw *hw, + u8 *ra, u16 tid, + enum ieee80211_back_parties initiator); + +/** + * ieee80211_stop_tx_ba_cb - low level driver ready to stop aggregate. + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * @ra: receiver address of the BA session recipient. + * @tid: the desired TID to BA on. + * + * This function must be called by low level driver once it has + * finished with preparations for the BA session tear down. + */ +void ieee80211_stop_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u8 tid); + +/** + * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate. + * @hw: pointer as obtained from ieee80211_alloc_hw(). + * @ra: receiver address of the BA session recipient. + * @tid: the desired TID to BA on. + * + * This function must be called by low level driver once it has + * finished with preparations for the BA session tear down. + * This version of the function is irq safe. + */ +void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra, + u16 tid); + #endif /* MAC80211_H */ diff --git a/include/net/wireless.h b/include/net/wireless.h index d30c4ba8fd9..c7f805ee554 100644 --- a/include/net/wireless.h +++ b/include/net/wireless.h @@ -13,6 +13,162 @@ #include <net/cfg80211.h> /** + * enum ieee80211_band - supported frequency bands + * + * The bands are assigned this way because the supported + * bitrates differ in these bands. + * + * @IEEE80211_BAND_2GHZ: 2.4GHz ISM band + * @IEEE80211_BAND_5GHZ: around 5GHz band (4.9-5.7) + */ +enum ieee80211_band { + IEEE80211_BAND_2GHZ, + IEEE80211_BAND_5GHZ, + + /* keep last */ + IEEE80211_NUM_BANDS +}; + +/** + * enum ieee80211_channel_flags - channel flags + * + * Channel flags set by the regulatory control code. + * + * @IEEE80211_CHAN_DISABLED: This channel is disabled. + * @IEEE80211_CHAN_PASSIVE_SCAN: Only passive scanning is permitted + * on this channel. + * @IEEE80211_CHAN_NO_IBSS: IBSS is not allowed on this channel. + * @IEEE80211_CHAN_RADAR: Radar detection is required on this channel. + */ +enum ieee80211_channel_flags { + IEEE80211_CHAN_DISABLED = 1<<0, + IEEE80211_CHAN_PASSIVE_SCAN = 1<<1, + IEEE80211_CHAN_NO_IBSS = 1<<2, + IEEE80211_CHAN_RADAR = 1<<3, +}; + +/** + * struct ieee80211_channel - channel definition + * + * This structure describes a single channel for use + * with cfg80211. + * + * @center_freq: center frequency in MHz + * @hw_value: hardware-specific value for the channel + * @flags: channel flags from &enum ieee80211_channel_flags. + * @orig_flags: channel flags at registration time, used by regulatory + * code to support devices with additional restrictions + * @band: band this channel belongs to. + * @max_antenna_gain: maximum antenna gain in dBi + * @max_power: maximum transmission power (in dBm) + * @orig_mag: internal use + * @orig_mpwr: internal use + */ +struct ieee80211_channel { + enum ieee80211_band band; + u16 center_freq; + u16 hw_value; + u32 flags; + int max_antenna_gain; + int max_power; + u32 orig_flags; + int orig_mag, orig_mpwr; +}; + +/** + * enum ieee80211_rate_flags - rate flags + * + * Hardware/specification flags for rates. These are structured + * in a way that allows using the same bitrate structure for + * different bands/PHY modes. + * + * @IEEE80211_RATE_SHORT_PREAMBLE: Hardware can send with short + * preamble on this bitrate; only relevant in 2.4GHz band and + * with CCK rates. + * @IEEE80211_RATE_MANDATORY_A: This bitrate is a mandatory rate + * when used with 802.11a (on the 5 GHz band); filled by the + * core code when registering the wiphy. + * @IEEE80211_RATE_MANDATORY_B: This bitrate is a mandatory rate + * when used with 802.11b (on the 2.4 GHz band); filled by the + * core code when registering the wiphy. + * @IEEE80211_RATE_MANDATORY_G: This bitrate is a mandatory rate + * when used with 802.11g (on the 2.4 GHz band); filled by the + * core code when registering the wiphy. + * @IEEE80211_RATE_ERP_G: This is an ERP rate in 802.11g mode. + */ +enum ieee80211_rate_flags { + IEEE80211_RATE_SHORT_PREAMBLE = 1<<0, + IEEE80211_RATE_MANDATORY_A = 1<<1, + IEEE80211_RATE_MANDATORY_B = 1<<2, + IEEE80211_RATE_MANDATORY_G = 1<<3, + IEEE80211_RATE_ERP_G = 1<<4, +}; + +/** + * struct ieee80211_rate - bitrate definition + * + * This structure describes a bitrate that an 802.11 PHY can + * operate with. The two values @hw_value and @hw_value_short + * are only for driver use when pointers to this structure are + * passed around. + * + * @flags: rate-specific flags + * @bitrate: bitrate in units of 100 Kbps + * @hw_value: driver/hardware value for this rate + * @hw_value_short: driver/hardware value for this rate when + * short preamble is used + */ +struct ieee80211_rate { + u32 flags; + u16 bitrate; + u16 hw_value, hw_value_short; +}; + +/** + * struct ieee80211_ht_info - describing STA's HT capabilities + * + * This structure describes most essential parameters needed + * to describe 802.11n HT capabilities for an STA. + * + * @ht_supported: is HT supported by STA, 0: no, 1: yes + * @cap: HT capabilities map as described in 802.11n spec + * @ampdu_factor: Maximum A-MPDU length factor + * @ampdu_density: Minimum A-MPDU spacing + * @supp_mcs_set: Supported MCS set as described in 802.11n spec + */ +struct ieee80211_ht_info { + u16 cap; /* use IEEE80211_HT_CAP_ */ + u8 ht_supported; + u8 ampdu_factor; + u8 ampdu_density; + u8 supp_mcs_set[16]; +}; + +/** + * struct ieee80211_supported_band - frequency band definition + * + * This structure describes a frequency band a wiphy + * is able to operate in. + * + * @channels: Array of channels the hardware can operate in + * in this band. + * @band: the band this structure represents + * @n_channels: Number of channels in @channels + * @bitrates: Array of bitrates the hardware can operate with + * in this band. Must be sorted to give a valid "supported + * rates" IE, i.e. CCK rates first, then OFDM. + * @n_bitrates: Number of bitrates in @bitrates + */ +struct ieee80211_supported_band { + struct ieee80211_channel *channels; + struct ieee80211_rate *bitrates; + enum ieee80211_band band; + int n_channels; + int n_bitrates; + struct ieee80211_ht_info ht_info; +}; + +/** * struct wiphy - wireless hardware description * @idx: the wiphy index assigned to this item * @class_dev: the class device representing /sys/class/ieee80211/<wiphy-name> @@ -30,6 +186,8 @@ struct wiphy { * help determine whether you own this wiphy or not. */ void *privid; + struct ieee80211_supported_band *bands[IEEE80211_NUM_BANDS]; + /* fields below are read-only, assigned by cfg80211 */ /* the item in /sys/class/ieee80211/ points to this, @@ -136,4 +294,14 @@ extern void wiphy_unregister(struct wiphy *wiphy); */ extern void wiphy_free(struct wiphy *wiphy); +/** + * ieee80211_channel_to_frequency - convert channel number to frequency + */ +extern int ieee80211_channel_to_frequency(int chan); + +/** + * ieee80211_frequency_to_channel - convert frequency to channel number + */ +extern int ieee80211_frequency_to_channel(int freq); + #endif /* __NET_WIRELESS_H */ |