[ARM] 4124/1: Rename mach-at91rm9200 and arch-at91rm9200 directories

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

1 files changed, 0 insertions, 121 deletions

diff --git a/include/asm-arm/arch-at91rm9200/board.h b/include/asm-arm/arch-at91rm9200/board.h
deleted file mode 100644
index f3a974ba3b5..00000000000
--- a/include/asm-arm/arch-at91rm9200/board.h
+++ /dev/null
@@ -1,121 +0,0 @@
-/*
- * include/asm-arm/arch-at91rm9200/board.h
- *
- *  Copyright (C) 2005 HP Labs
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-/*
- * These are data structures found in platform_device.dev.platform_data,
- * and describing board-specific data needed by drivers.  For example,
- * which pin is used for a given GPIO role.
- *
- * In 2.6, drivers should strongly avoid board-specific knowledge so
- * that supporting new boards normally won't require driver patches.
- * Most board-specific knowledge should be in arch/.../board-*.c files.
- */
-
-#ifndef __ASM_ARCH_BOARD_H
-#define __ASM_ARCH_BOARD_H
-
-#include <linux/mtd/partitions.h>
-#include <linux/device.h>
-#include <linux/spi/spi.h>
-
- /* USB Device */
-struct at91_udc_data {
-	u8	vbus_pin;		/* high == host powering us */
-	u8	pullup_pin;		/* high == D+ pulled up */
-};
-extern void __init at91_add_device_udc(struct at91_udc_data *data);
-
- /* Compact Flash */
-struct at91_cf_data {
-	u8	irq_pin;		/* I/O IRQ */
-	u8	det_pin;		/* Card detect */
-	u8	vcc_pin;		/* power switching */
-	u8	rst_pin;		/* card reset */
-	u8	chipselect;		/* EBI Chip Select number */
-};
-extern void __init at91_add_device_cf(struct at91_cf_data *data);
-
- /* MMC / SD */
-struct at91_mmc_data {
-	u8		det_pin;	/* card detect IRQ */
-	unsigned	slot_b:1;	/* uses Slot B */
-	unsigned	wire4:1;	/* (SD) supports DAT0..DAT3 */
-	u8		wp_pin;		/* (SD) writeprotect detect */
-	u8		vcc_pin;	/* power switching (high == on) */
-};
-extern void __init at91_add_device_mmc(struct at91_mmc_data *data);
-
- /* Ethernet */
-struct at91_eth_data {
-	u8		phy_irq_pin;	/* PHY IRQ */
-	u8		is_rmii;	/* using RMII interface? */
-};
-extern void __init at91_add_device_eth(struct at91_eth_data *data);
-
-#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263)
-#define eth_platform_data	at91_eth_data
-#endif
-
- /* USB Host */
-struct at91_usbh_data {
-	u8		ports;		/* number of ports on root hub */
-};
-extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
-
- /* NAND / SmartMedia */
-struct at91_nand_data {
-	u8		enable_pin;	/* chip enable */
-	u8		det_pin;	/* card detect */
-	u8		rdy_pin;	/* ready/busy */
-	u8		ale;		/* address line number connected to ALE */
-	u8		cle;		/* address line number connected to CLE */
-	u8		bus_width_16;	/* buswidth is 16 bit */
-	struct mtd_partition* (*partition_info)(int, int*);
-};
-extern void __init at91_add_device_nand(struct at91_nand_data *data);
-
- /* I2C*/
-extern void __init at91_add_device_i2c(void);
-
- /* SPI */
-extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
-
- /* Serial */
-struct at91_uart_config {
-	unsigned short	console_tty;	/* tty number of serial console */
-	unsigned short	nr_tty;		/* number of serial tty's */
-	short		tty_map[];	/* map UART to tty number */
-};
-extern struct platform_device *atmel_default_console_device;
-extern void __init at91_init_serial(struct at91_uart_config *config);
-
-struct atmel_uart_data {
-	short		use_dma_tx;	/* use transmit DMA? */
-	short		use_dma_rx;	/* use receive DMA? */
-	void __iomem	*regs;		/* virtual base address, if any */
-};
-extern void __init at91_add_device_serial(void);
-
- /* LEDs */
-extern u8 at91_leds_cpu;
-extern u8 at91_leds_timer;
-extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
-
-#endif