[ARM] Remove EPXA10DB machine support

EPXA10DB seems to be uncared for:
- the "PLD" code has never been merged
- no one has reported that this platform has been broken since
  at least 2.6.10
- interest seems to have dried up around March 2003.

Therefore, remove EPXA10DB support.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

9 files changed, 0 insertions, 2025 deletions

diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
index b9b77cf39a1..7abd7fee0dd 100644
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -473,14 +473,6 @@ config MTD_IXP2000
 	  IXDP425 and Coyote. If you have an IXP2000 based board and
 	  would like to use the flash chips on it, say 'Y'.
 
-config MTD_EPXA10DB
-	tristate "CFI Flash device mapped on Epxa10db"
-	depends on MTD_CFI && MTD_PARTITIONS && ARCH_CAMELOT
-	help
-	  This enables support for the flash devices on the Altera
-	  Excalibur XA10 Development Board. If you are building a kernel
-	  for on of these boards then you should say 'Y' otherwise say 'N'.
-
 config MTD_FORTUNET
 	tristate "CFI Flash device mapped on the FortuNet board"
 	depends on MTD_CFI && MTD_PARTITIONS && SA1100_FORTUNET
diff --git a/drivers/mtd/maps/Makefile b/drivers/mtd/maps/Makefile
index 2f7e254912f..ab71f172eb7 100644
--- a/drivers/mtd/maps/Makefile
+++ b/drivers/mtd/maps/Makefile
@@ -15,7 +15,6 @@ obj-$(CONFIG_MTD_CFI_FLAGADM)	+= cfi_flagadm.o
 obj-$(CONFIG_MTD_CSTM_MIPS_IXX)	+= cstm_mips_ixx.o
 obj-$(CONFIG_MTD_DC21285)	+= dc21285.o
 obj-$(CONFIG_MTD_DILNETPC)	+= dilnetpc.o
-obj-$(CONFIG_MTD_EPXA10DB)	+= epxa10db-flash.o
 obj-$(CONFIG_MTD_IQ80310)	+= iq80310.o
 obj-$(CONFIG_MTD_L440GX)	+= l440gx.o
 obj-$(CONFIG_MTD_AMD76XROM)	+= amd76xrom.o
diff --git a/drivers/mtd/maps/epxa10db-flash.c b/drivers/mtd/maps/epxa10db-flash.c
deleted file mode 100644
index 265b079fe93..00000000000
--- a/drivers/mtd/maps/epxa10db-flash.c
+++ /dev/null
@@ -1,179 +0,0 @@
-/*
- * Flash memory access on EPXA based devices
- *
- * (C) 2000 Nicolas Pitre <nico@cam.org>
- *  Copyright (C) 2001 Altera Corporation
- *  Copyright (C) 2001 Red Hat, Inc.
- *
- * $Id: epxa10db-flash.c,v 1.15 2005/11/07 11:14:27 gleixner Exp $
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/map.h>
-#include <linux/mtd/partitions.h>
-
-#include <asm/io.h>
-#include <asm/hardware.h>
-
-#ifdef CONFIG_EPXA10DB
-#define BOARD_NAME "EPXA10DB"
-#else
-#define BOARD_NAME "EPXA1DB"
-#endif
-
-static int nr_parts = 0;
-static struct mtd_partition *parts;
-
-static struct mtd_info *mymtd;
-
-static int epxa_default_partitions(struct mtd_info *master, struct mtd_partition **pparts);
-
-
-static struct map_info epxa_map = {
-	.name =		"EPXA flash",
-	.size =		FLASH_SIZE,
-	.bankwidth =	2,
-	.phys =		FLASH_START,
-};
-
-static const char *probes[] = { "RedBoot", "afs", NULL };
-
-static int __init epxa_mtd_init(void)
-{
-	int i;
-
-	printk(KERN_NOTICE "%s flash device: 0x%x at 0x%x\n", BOARD_NAME, FLASH_SIZE, FLASH_START);
-
-	epxa_map.virt = ioremap(FLASH_START, FLASH_SIZE);
-	if (!epxa_map.virt) {
-		printk("Failed to ioremap %s flash\n",BOARD_NAME);
-		return -EIO;
-	}
-	simple_map_init(&epxa_map);
-
-	mymtd = do_map_probe("cfi_probe", &epxa_map);
-	if (!mymtd) {
-		iounmap((void *)epxa_map.virt);
-		return -ENXIO;
-	}
-
-	mymtd->owner = THIS_MODULE;
-
-	/* Unlock the flash device. */
-	if(mymtd->unlock){
-		for (i=0; i<mymtd->numeraseregions;i++){
-			int j;
-			for(j=0;j<mymtd->eraseregions[i].numblocks;j++){
-				mymtd->unlock(mymtd,mymtd->eraseregions[i].offset + j * mymtd->eraseregions[i].erasesize,mymtd->eraseregions[i].erasesize);
-			}
-		}
-	}
-
-#ifdef CONFIG_MTD_PARTITIONS
-	nr_parts = parse_mtd_partitions(mymtd, probes, &parts, 0);
-
-	if (nr_parts > 0) {
-		add_mtd_partitions(mymtd, parts, nr_parts);
-		return 0;
-	}
-#endif
-	/* No recognised partitioning schemes found - use defaults */
-	nr_parts = epxa_default_partitions(mymtd, &parts);
-	if (nr_parts > 0) {
-		add_mtd_partitions(mymtd, parts, nr_parts);
-		return 0;
-	}
-
-	/* If all else fails... */
-	add_mtd_device(mymtd);
-	return 0;
-}
-
-static void __exit epxa_mtd_cleanup(void)
-{
-	if (mymtd) {
-		if (nr_parts)
-			del_mtd_partitions(mymtd);
-		else
-			del_mtd_device(mymtd);
-		map_destroy(mymtd);
-	}
-	if (epxa_map.virt) {
-		iounmap((void *)epxa_map.virt);
-		epxa_map.virt = 0;
-	}
-}
-
-
-/*
- * This will do for now, once we decide which bootldr we're finally
- * going to use then we'll remove this function and do it properly
- *
- * Partions are currently (as offsets from base of flash):
- * 0x00000000 - 0x003FFFFF - bootloader (!)
- * 0x00400000 - 0x00FFFFFF - Flashdisk
- */
-
-static int __init epxa_default_partitions(struct mtd_info *master, struct mtd_partition **pparts)
-{
-	struct mtd_partition *parts;
-	int ret, i;
-	int npartitions = 0;
-	char *names;
-	const char *name = "jffs";
-
-	printk("Using default partitions for %s\n",BOARD_NAME);
-	npartitions=1;
-	parts = kmalloc(npartitions*sizeof(*parts)+strlen(name), GFP_KERNEL);
-	memzero(parts,npartitions*sizeof(*parts)+strlen(name));
-	if (!parts) {
-		ret = -ENOMEM;
-		goto out;
-	}
-	i=0;
-	names = (char *)&parts[npartitions];
-	parts[i].name = names;
-	names += strlen(name) + 1;
-	strcpy(parts[i].name, name);
-
-#ifdef CONFIG_EPXA10DB
-	parts[i].size = FLASH_SIZE-0x00400000;
-	parts[i].offset = 0x00400000;
-#else
-	parts[i].size = FLASH_SIZE-0x00180000;
-	parts[i].offset = 0x00180000;
-#endif
-
- out:
-	*pparts = parts;
-	return npartitions;
-}
-
-
-module_init(epxa_mtd_init);
-module_exit(epxa_mtd_cleanup);
-
-MODULE_AUTHOR("Clive Davies");
-MODULE_DESCRIPTION("Altera epxa mtd flash map");
-MODULE_LICENSE("GPL");
diff --git a/drivers/net/arm/Kconfig b/drivers/net/arm/Kconfig
index 470364deded..625184b65e3 100644
--- a/drivers/net/arm/Kconfig
+++ b/drivers/net/arm/Kconfig
@@ -31,16 +31,3 @@ config ARM_ETHERH
 	help
 	  If you have an Acorn system with one of these network cards, you
 	  should say Y to this option if you wish to use it with Linux.
-
-config ARM_ETHER00
-	tristate "Altera Ether00 support"
-	depends on NET_ETHERNET && ARM && ARCH_CAMELOT
-	help
-	  This is the driver for Altera's ether00 ethernet mac IP core. Say
-	  Y here if you want to build support for this into the kernel. It
-	  is also available as a module (say M here) that can be inserted/
-	  removed from the kernel at the same time as the PLD is configured.
-	  If this driver is running on an epxa10 development board then it
-	  will generate a suitable hw address based on the board serial
-	  number (MTD support is required for this). Otherwise you will
-	  need to set a suitable hw address using ifconfig.
diff --git a/drivers/net/arm/Makefile b/drivers/net/arm/Makefile
index b0d706834d8..bc263edf06a 100644
--- a/drivers/net/arm/Makefile
+++ b/drivers/net/arm/Makefile
@@ -4,7 +4,6 @@
 #
 
 obj-$(CONFIG_ARM_AM79C961A)	+= am79c961a.o
-obj-$(CONFIG_ARM_ETHER00)	+= ether00.o
 obj-$(CONFIG_ARM_ETHERH)	+= etherh.o
 obj-$(CONFIG_ARM_ETHER3)	+= ether3.o
 obj-$(CONFIG_ARM_ETHER1)	+= ether1.o
diff --git a/drivers/net/arm/ether00.c b/drivers/net/arm/ether00.c
deleted file mode 100644
index 4f1f4e31bda..00000000000
--- a/drivers/net/arm/ether00.c
+++ /dev/null
@@ -1,1017 +0,0 @@
-/*
- *  drivers/net/ether00.c
- *
- *  Copyright (C) 2001 Altera Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-/* includes */
-#include <linux/config.h>
-#include <linux/pci.h>
-#include <linux/sched.h>
-#include <linux/netdevice.h>
-#include <linux/skbuff.h>
-#include <linux/etherdevice.h>
-#include <linux/module.h>
-#include <linux/tqueue.h>
-#include <linux/mtd/mtd.h>
-#include <linux/pld/pld_hotswap.h>
-#include <asm/arch/excalibur.h>
-#include <asm/arch/hardware.h>
-#include <asm/irq.h>
-#include <asm/io.h>
-#include <asm/sizes.h>
-
-#include <asm/arch/ether00.h>
-#include <asm/arch/tdkphy.h>
-
-
-MODULE_AUTHOR("Clive Davies");
-MODULE_DESCRIPTION("Altera Ether00 IP core driver");
-MODULE_LICENSE("GPL");
-
-#define PKT_BUF_SZ 1540 /* Size of each rx buffer */
-#define ETH_NR 4 /* Number of MACs this driver supports */
-
-#define DEBUG(x)
-
-#define __dma_va(x) (unsigned int)((unsigned int)priv->dma_data+(((unsigned int)(x))&(EXC_SPSRAM_BLOCK0_SIZE-1)))
-#define __dma_pa(x) (unsigned int)(EXC_SPSRAM_BLOCK0_BASE+(((unsigned int)(x))-(unsigned int)priv->dma_data))
-
-#define ETHER00_BASE	0
-#define	ETHER00_TYPE
-#define ETHER00_NAME "ether00"
-#define MAC_REG_SIZE 0x400 /* size of MAC register area */
-
-
-
-/* typedefs */
-
-/* The definition of the driver control structure */
-
-#define RX_NUM_BUFF     10
-#define RX_NUM_FDESC    10
-#define TX_NUM_FDESC    10
-
-struct tx_fda_ent{
-	FDA_DESC  fd;
-	BUF_DESC  bd;
-	BUF_DESC  pad;
-};
-struct rx_fda_ent{
-	FDA_DESC  fd;
-	BUF_DESC  bd;
-	BUF_DESC  pad;
-};
-struct rx_blist_ent{
-	FDA_DESC  fd;
-	BUF_DESC  bd;
-	BUF_DESC  pad;
-};
-struct net_priv
-{
-	struct net_device_stats stats;
-	struct sk_buff* skb;
-	void* dma_data;
-	struct rx_blist_ent*  rx_blist_vp;
-	struct rx_fda_ent* rx_fda_ptr;
-	struct tx_fda_ent* tx_fdalist_vp;
-	struct tq_struct  tq_memupdate;
-	unsigned char   memupdate_scheduled;
-	unsigned char   rx_disabled;
-	unsigned char   queue_stopped;
-	spinlock_t rx_lock;
-};
-
-static const char vendor_id[2]={0x07,0xed};
-
-#ifdef ETHER00_DEBUG
-
-/* Dump (most) registers for debugging puposes */
-
-static void dump_regs(struct net_device *dev){
-	struct net_priv* priv=dev->priv;
-	unsigned int* i;
-
-	printk("\n RX free descriptor area:\n");
-
-	for(i=(unsigned int*)priv->rx_fda_ptr;
-	    i<((unsigned int*)(priv->rx_fda_ptr+RX_NUM_FDESC));){
-		printk("%#8x %#8x %#8x %#8x\n",*i,*(i+1),*(i+2),*(i+3));
-		i+=4;
-	}
-
-	printk("\n RX buffer list:\n");
-
-	for(i=(unsigned int*)priv->rx_blist_vp;
-	    i<((unsigned int*)(priv->rx_blist_vp+RX_NUM_BUFF));){
-		printk("%#8x %#8x %#8x %#8x\n",*i,*(i+1),*(i+2),*(i+3));
-		i+=4;
-	}
-
-	printk("\n TX frame descriptor list:\n");
-
-	for(i=(unsigned int*)priv->tx_fdalist_vp;
-	    i<((unsigned int*)(priv->tx_fdalist_vp+TX_NUM_FDESC));){
-		printk("%#8x %#8x %#8x %#8x\n",*i,*(i+1),*(i+2),*(i+3));
-		i+=4;
-	}
-
-	printk("\ndma ctl=%#x\n",readw(ETHER_DMA_CTL(dev->base_addr)));
-	printk("txfrmptr=%#x\n",readw(ETHER_TXFRMPTR(dev->base_addr)));
-	printk("txthrsh=%#x\n",readw(ETHER_TXTHRSH(dev->base_addr)));
-	printk("txpollctr=%#x\n",readw(ETHER_TXPOLLCTR(dev->base_addr)));
-	printk("blfrmptr=%#x\n",readw(ETHER_BLFRMPTR(dev->base_addr)));
-	printk("rxfragsize=%#x\n",readw(ETHER_RXFRAGSIZE(dev->base_addr)));
-	printk("tx_int_en=%#x\n",readw(ETHER_INT_EN(dev->base_addr)));
-	printk("fda_bas=%#x\n",readw(ETHER_FDA_BAS(dev->base_addr)));
-	printk("fda_lim=%#x\n",readw(ETHER_FDA_LIM(dev->base_addr)));
-	printk("int_src=%#x\n",readw(ETHER_INT_SRC(dev->base_addr)));
-	printk("pausecnt=%#x\n",readw(ETHER_PAUSECNT(dev->base_addr)));
-	printk("rempaucnt=%#x\n",readw(ETHER_REMPAUCNT(dev->base_addr)));
-	printk("txconfrmstat=%#x\n",readw(ETHER_TXCONFRMSTAT(dev->base_addr)));
-	printk("mac_ctl=%#x\n",readw(ETHER_MAC_CTL(dev->base_addr)));
-	printk("arc_ctl=%#x\n",readw(ETHER_ARC_CTL(dev->base_addr)));
-	printk("tx_ctl=%#x\n",readw(ETHER_TX_CTL(dev->base_addr)));
-}
-#endif /* ETHER00_DEBUG */
-
-
-static int ether00_write_phy(struct net_device *dev, short address, short value)
-{
-	volatile int count = 1024;
-	writew(value,ETHER_MD_DATA(dev->base_addr));
-	writew( ETHER_MD_CA_BUSY_MSK |
-		ETHER_MD_CA_WR_MSK |
-		(address & ETHER_MD_CA_ADDR_MSK),
-		ETHER_MD_CA(dev->base_addr));
-
-	/* Wait for the command to complete */
-	while((readw(ETHER_MD_CA(dev->base_addr)) & ETHER_MD_CA_BUSY_MSK)&&count){
-		count--;
-	}
-	if (!count){
-		printk("Write to phy failed, addr=%#x, data=%#x\n",address, value);
-		return -EIO;
-	}
-	return 0;
-}
-
-static int ether00_read_phy(struct net_device *dev, short address)
-{
-	volatile int count = 1024;
-	writew( ETHER_MD_CA_BUSY_MSK |
-		(address & ETHER_MD_CA_ADDR_MSK),
-		ETHER_MD_CA(dev->base_addr));
-
-	/* Wait for the command to complete */
-	while((readw(ETHER_MD_CA(dev->base_addr)) & ETHER_MD_CA_BUSY_MSK)&&count){
-		count--;
-	}
-	if (!count){
-		printk(KERN_WARNING "Read from phy timed out\n");
-		return -EIO;
-	}
-	return readw(ETHER_MD_DATA(dev->base_addr));
-}
-
-static void ether00_phy_int(int irq_num, void* dev_id, struct pt_regs* regs)
-{
-	struct net_device* dev=dev_id;
-	int irq_status;
-
-	irq_status=ether00_read_phy(dev, PHY_IRQ_CONTROL);
-
-	if(irq_status & PHY_IRQ_CONTROL_ANEG_COMP_INT_MSK){
-		/*
-		 * Autonegotiation complete on epxa10db. The mac doesn't
-		 * twig if we're in full duplex so we need to check the
-		 * phy status register and configure the mac accordingly
-		 */
-		if(ether00_read_phy(dev, PHY_STATUS)&(PHY_STATUS_10T_F_MSK|PHY_STATUS_100_X_F_MSK)){
-			int tmp;
-			tmp=readl(ETHER_MAC_CTL(dev->base_addr));
-			writel(tmp|ETHER_MAC_CTL_FULLDUP_MSK,ETHER_MAC_CTL(dev->base_addr));
-		}
-	}
-
-	if(irq_status&PHY_IRQ_CONTROL_LS_CHG_INT_MSK){
-
-		if(ether00_read_phy(dev, PHY_STATUS)& PHY_STATUS_LINK_MSK){
-			/* Link is up */
-			netif_carrier_on(dev);
-			//printk("Carrier on\n");
-		}else{
-			netif_carrier_off(dev);
-			//printk("Carrier off\n");
-
-		}
-	}
-
-}
-
-static void setup_blist_entry(struct sk_buff* skb,struct rx_blist_ent* blist_ent_ptr){
-	/* Make the buffer consistent with the cache as the mac is going to write
-	 * directly into it*/
-	blist_ent_ptr->fd.FDSystem=(unsigned int)skb;
-	blist_ent_ptr->bd.BuffData=(char*)__pa(skb->data);
-	consistent_sync(skb->data,PKT_BUF_SZ,PCI_DMA_FROMDEVICE);
-        /* align IP on 16 Byte (DMA_CTL set to skip 2 bytes) */
-	skb_reserve(skb,2);
-	blist_ent_ptr->bd.BuffLength=PKT_BUF_SZ-2;
-	blist_ent_ptr->fd.FDLength=1;
-	blist_ent_ptr->fd.FDCtl=FDCTL_COWNSFD_MSK;
-	blist_ent_ptr->bd.BDCtl=BDCTL_COWNSBD_MSK;
-}
-
-
-static int ether00_mem_init(struct net_device* dev)
-{
-	struct net_priv* priv=dev->priv;
-	struct tx_fda_ent *tx_fd_ptr,*tx_end_ptr;
-	struct rx_blist_ent* blist_ent_ptr;
-	int i;
-
-	/*
-	 * Grab a block of on chip SRAM to contain the control stuctures for
-	 * the ethernet MAC. This uncached becuase it needs to be accesses by both
-	 * bus masters (cpu + mac). However, it shouldn't matter too much in terms
-	 * of speed as its on chip memory
-	 */
-	priv->dma_data=ioremap_nocache(EXC_SPSRAM_BLOCK0_BASE,EXC_SPSRAM_BLOCK0_SIZE );
-	if (!priv->dma_data)
-		return -ENOMEM;
-
-	priv->rx_fda_ptr=(struct rx_fda_ent*)priv->dma_data;
-	/*
-	 * Now share it out amongst the Frame descriptors and the buffer list
-	 */
-	priv->rx_blist_vp=(struct rx_blist_ent*)((unsigned int)priv->dma_data+RX_NUM_FDESC*sizeof(struct rx_fda_ent));
-
-	/*
-	 *Initalise the FDA list
-	 */
-	/* set ownership to the controller */
-	memset(priv->rx_fda_ptr,0x80,RX_NUM_FDESC*sizeof(struct rx_fda_ent));
-
-	/*
-	 *Initialise the buffer list
-	 */
-	blist_ent_ptr=priv->rx_blist_vp;
-	i=0;
-	while(blist_ent_ptr<(priv->rx_blist_vp+RX_NUM_BUFF)){
-		struct sk_buff *skb;
-		blist_ent_ptr->fd.FDLength=1;
-		skb=dev_alloc_skb(PKT_BUF_SZ);
-		if(skb){
-			setup_blist_entry(skb,blist_ent_ptr);
-			blist_ent_ptr->fd.FDNext=(FDA_DESC*)__dma_pa(blist_ent_ptr+1);
-			blist_ent_ptr->bd.BDStat=i++;
-			blist_ent_ptr++;
-		}
-		else
-		{
-			printk("Failed to initalise buffer list\n");
-		}
-
-	}
-	blist_ent_ptr--;
-	blist_ent_ptr->fd.FDNext=(FDA_DESC*)__dma_pa(priv->rx_blist_vp);
-
-	priv->tx_fdalist_vp=(struct tx_fda_ent*)(priv->rx_blist_vp+RX_NUM_BUFF);
-
-	/* Initialise the buffers to be a circular list. The mac will then go poll
-	 * the list until it finds a frame ready to transmit */
-	tx_end_ptr=priv->tx_fdalist_vp+TX_NUM_FDESC;
-	for(tx_fd_ptr=priv->tx_fdalist_vp;tx_fd_ptr<tx_end_ptr;tx_fd_ptr++){
-		tx_fd_ptr->fd.FDNext=(FDA_DESC*)__dma_pa((tx_fd_ptr+1));
-		tx_fd_ptr->fd.FDCtl=1;
-		tx_fd_ptr->fd.FDStat=0;
-		tx_fd_ptr->fd.FDLength=1;
-
-	}
-	/* Change the last FDNext pointer to make a circular list */
-	tx_fd_ptr--;
-	tx_fd_ptr->fd.FDNext=(FDA_DESC*)__dma_pa(priv->tx_fdalist_vp);
-
-	/* Point the device at the chain of Rx and Tx Buffers */
-	writel((unsigned int)__dma_pa(priv->rx_fda_ptr),ETHER_FDA_BAS(dev->base_addr));
-	writel((RX_NUM_FDESC-1)*sizeof(struct rx_fda_ent),ETHER_FDA_LIM(dev->base_addr));
-	writel((unsigned int)__dma_pa(priv->rx_blist_vp),ETHER_BLFRMPTR(dev->base_addr));
-
-	writel((unsigned int)__dma_pa(priv->tx_fdalist_vp),ETHER_TXFRMPTR(dev->base_addr));
-
-	return 0;
-}
-
-
-void ether00_mem_update(void* dev_id)
-{
-	struct net_device* dev=dev_id;
-	struct net_priv* priv=dev->priv;
-	struct sk_buff* skb;
-	struct tx_fda_ent *fda_ptr=priv->tx_fdalist_vp;
-	struct rx_blist_ent* blist_ent_ptr;
-	unsigned long flags;
-
-	priv->tq_memupdate.sync=0;
-	//priv->tq_memupdate.list=
-	priv->memupdate_scheduled=0;
-
-	/* Transmit interrupt */
-	while(fda_ptr<(priv->tx_fdalist_vp+TX_NUM_FDESC)){
-		if(!(FDCTL_COWNSFD_MSK&fda_ptr->fd.FDCtl) && (ETHER_TX_STAT_COMP_MSK&fda_ptr->fd.FDStat)){
-			priv->stats.tx_packets++;
-			priv->stats.tx_bytes+=fda_ptr->bd.BuffLength;
-			skb=(struct sk_buff*)fda_ptr->fd.FDSystem;
-			//printk("%d:txcln:fda=%#x skb=%#x\n",jiffies,fda_ptr,skb);
-			dev_kfree_skb(skb);
-			fda_ptr->fd.FDSystem=0;
-			fda_ptr->fd.FDStat=0;
-			fda_ptr->fd.FDCtl=0;
-		}
-		fda_ptr++;
-	}
-	/* Fill in any missing buffers from the received queue */
-	spin_lock_irqsave(&priv->rx_lock,flags);
-	blist_ent_ptr=priv->rx_blist_vp;
-	while(blist_ent_ptr<(priv->rx_blist_vp+RX_NUM_BUFF)){
-		/* fd.FDSystem of 0 indicates we failed to allocate the buffer in the ISR */
-		if(!blist_ent_ptr->fd.FDSystem){
-			struct sk_buff *skb;
-			skb=dev_alloc_skb(PKT_BUF_SZ);
-			blist_ent_ptr->fd.FDSystem=(unsigned int)skb;
-			if(skb){
-				setup_blist_entry(skb,blist_ent_ptr);
-			}
-			else
-			{
-				break;
-			}
-		}
-		blist_ent_ptr++;
-	}
-	spin_unlock_irqrestore(&priv->rx_lock,flags);
-	if(priv->queue_stopped){
-		//printk("%d:cln:start q\n",jiffies);
-		netif_start_queue(dev);
-	}
-	if(priv->rx_disabled){
-		//printk("%d:enable_irq\n",jiffies);
-		priv->rx_disabled=0;
-		writel(ETHER_RX_CTL_RXEN_MSK,ETHER_RX_CTL(dev->base_addr));
-
-	}
-}
-
-
-static void ether00_int( int irq_num, void* dev_id, struct pt_regs* regs)
-{
-	struct net_device* dev=dev_id;
-	struct net_priv* priv=dev->priv;
-
-	unsigned int   interruptValue;
-
-	interruptValue=readl(ETHER_INT_SRC(dev->base_addr));
-
-	//printk("INT_SRC=%x\n",interruptValue);
-
-	if(!(readl(ETHER_INT_SRC(dev->base_addr)) & ETHER_INT_SRC_IRQ_MSK))
-	{
-		return;		/* Interrupt wasn't caused by us!! */
-	}
-
-	if(readl(ETHER_INT_SRC(dev->base_addr))&
-	   (ETHER_INT_SRC_INTMACRX_MSK |
-	    ETHER_INT_SRC_FDAEX_MSK |
-	    ETHER_INT_SRC_BLEX_MSK)) {
-		struct rx_blist_ent* blist_ent_ptr;
-		struct rx_fda_ent* fda_ent_ptr;
-		struct sk_buff* skb;
-
-		fda_ent_ptr=priv->rx_fda_ptr;
-		spin_lock(&priv->rx_lock);
-		while(fda_ent_ptr<(priv->rx_fda_ptr+RX_NUM_FDESC)){
-			int result;
-
-			if(!(fda_ent_ptr->fd.FDCtl&FDCTL_COWNSFD_MSK))
-			{
-				/* This frame is ready for processing */
-				/*find the corresponding buffer in the bufferlist */
-				blist_ent_ptr=priv->rx_blist_vp+fda_ent_ptr->bd.BDStat;
-				skb=(struct sk_buff*)blist_ent_ptr->fd.FDSystem;
-
-				/* Pass this skb up the stack */
-				skb->dev=dev;
-				skb_put(skb,fda_ent_ptr->fd.FDLength);
-				skb->protocol=eth_type_trans(skb,dev);
-				skb->ip_summed=CHECKSUM_UNNECESSARY;
-				result=netif_rx(skb);
-				/* Update statistics */
-				priv->stats.rx_packets++;
-				priv->stats.rx_bytes+=fda_ent_ptr->fd.FDLength;
-
-				/* Free the FDA entry */
-				fda_ent_ptr->bd.BDStat=0xff;
-				fda_ent_ptr->fd.FDCtl=FDCTL_COWNSFD_MSK;
-
-				/* Allocate a new skb and point the bd entry to it */
-				blist_ent_ptr->fd.FDSystem=0;
-				skb=dev_alloc_skb(PKT_BUF_SZ);
-				//printk("allocskb=%#x\n",skb);
-				if(skb){
-					setup_blist_entry(skb,blist_ent_ptr);
-
-				}
-				else if(!priv->memupdate_scheduled){
-					int tmp;
-					/* There are no buffers at the moment, so schedule */
-					/* the background task to sort this out */
-					schedule_task(&priv->tq_memupdate);
-					priv->memupdate_scheduled=1;
-					printk(KERN_DEBUG "%s:No buffers",dev->name);
-					/* If this interrupt was due to a lack of buffers then
-					 * we'd better stop the receiver too */
-					if(interruptValue&ETHER_INT_SRC_BLEX_MSK){
-						priv->rx_disabled=1;
-						tmp=readl(ETHER_INT_SRC(dev->base_addr));
-						writel(tmp&~ETHER_RX_CTL_RXEN_MSK,ETHER_RX_CTL(dev->base_addr));
-						printk(KERN_DEBUG "%s:Halting rx",dev->name);
-					}
-
-				}
-
-			}
-			fda_ent_ptr++;
-		}
-		spin_unlock(&priv->rx_lock);
-
-		/* Clear the  interrupts */
-		writel(ETHER_INT_SRC_INTMACRX_MSK | ETHER_INT_SRC_FDAEX_MSK
-		       | ETHER_INT_SRC_BLEX_MSK,ETHER_INT_SRC(dev->base_addr));
-
-	}
-
-	if(readl(ETHER_INT_SRC(dev->base_addr))&ETHER_INT_SRC_INTMACTX_MSK){
-
-		if(!priv->memupdate_scheduled){
-			schedule_task(&priv->tq_memupdate);
-			priv->memupdate_scheduled=1;
-		}
-		/* Clear the interrupt */
-		writel(ETHER_INT_SRC_INTMACTX_MSK,ETHER_INT_SRC(dev->base_addr));
-	}
-
-	if (readl(ETHER_INT_SRC(dev->base_addr)) & (ETHER_INT_SRC_SWINT_MSK|
-						    ETHER_INT_SRC_INTEARNOT_MSK|
-						    ETHER_INT_SRC_INTLINK_MSK|
-						    ETHER_INT_SRC_INTEXBD_MSK|
-						    ETHER_INT_SRC_INTTXCTLCMP_MSK))
-	{
-		/*
-		 *	Not using any of these so they shouldn't happen
-		 *
-		 *	In the cased of INTEXBD - if you allocate more
-		 *      than 28 decsriptors you may need to think about this
-		 */
-		printk("Not using this interrupt\n");
-	}
-
-	if (readl(ETHER_INT_SRC(dev->base_addr)) &
-	    (ETHER_INT_SRC_INTSBUS_MSK |
-	     ETHER_INT_SRC_INTNRABT_MSK
-	     |ETHER_INT_SRC_DMPARERR_MSK))
-	{
-		/*
-		 * Hardware errors, we can either ignore them and hope they go away
-		 *or reset the device, I'll try the first for now to see if they happen
-		 */
-		printk("Hardware error\n");
-	}
-}
-
-static void ether00_setup_ethernet_address(struct net_device* dev)
-{
-	int tmp;
-
-	dev->addr_len=6;
-	writew(0,ETHER_ARC_ADR(dev->base_addr));
-	writel((dev->dev_addr[0]<<24) |
-		(dev->dev_addr[1]<<16) |
-		(dev->dev_addr[2]<<8) |
-		dev->dev_addr[3],
-		ETHER_ARC_DATA(dev->base_addr));
-
-	writew(4,ETHER_ARC_ADR(dev->base_addr));
-	tmp=readl(ETHER_ARC_DATA(dev->base_addr));
-	tmp&=0xffff;
-	tmp|=(dev->dev_addr[4]<<24) | (dev->dev_addr[5]<<16);
-	writel(tmp, ETHER_ARC_DATA(dev->base_addr));
-	/* Enable this entry in the ARC */
-
-	writel(1,ETHER_ARC_ENA(dev->base_addr));
-
-	return;
-}
-
-
-static void ether00_reset(struct net_device *dev)
-{
-	/* reset the controller */
-	writew(ETHER_MAC_CTL_RESET_MSK,ETHER_MAC_CTL(dev->base_addr));
-
-	/*
-	 * Make sure we're not going to send anything
-	 */
-
-	writew(ETHER_TX_CTL_TXHALT_MSK,ETHER_TX_CTL(dev->base_addr));
-
-	/*
-	 * Make sure we're not going to receive anything
-	 */
-	writew(ETHER_RX_CTL_RXHALT_MSK,ETHER_RX_CTL(dev->base_addr));
-
-	/*
-	 * Disable Interrupts for now, and set the burst size to 8 bytes
-	 */
-
-	writel(ETHER_DMA_CTL_INTMASK_MSK |
-	       ((8 << ETHER_DMA_CTL_DMBURST_OFST) & ETHER_DMA_CTL_DMBURST_MSK)
-	       |(2<<ETHER_DMA_CTL_RXALIGN_OFST),
-	       ETHER_DMA_CTL(dev->base_addr));
-
-
-	/*
-	 * Set TxThrsh - start transmitting a packet after 1514
-	 * bytes or when a packet is complete, whichever comes first
-	 */
-	 writew(1514,ETHER_TXTHRSH(dev->base_addr));
-
-	/*
-	 * Set TxPollCtr.  Each cycle is
-	 * 61.44 microseconds with a 33 MHz bus
-	 */
-	 writew(1,ETHER_TXPOLLCTR(dev->base_addr));
-
-	/*
-	 * Set Rx_Ctl - Turn off reception and let RxData turn it
-	 * on later
-	 */
-	 writew(ETHER_RX_CTL_RXHALT_MSK,ETHER_RX_CTL(dev->base_addr));
-
-}
-
-
-static void ether00_set_multicast(struct net_device* dev)
-{
-	int count=dev->mc_count;
-
-	/* Set promiscuous mode if it's asked for. */
-
-	if (dev->flags&IFF_PROMISC){
-
-		writew( ETHER_ARC_CTL_COMPEN_MSK |
-			ETHER_ARC_CTL_BROADACC_MSK |
-			ETHER_ARC_CTL_GROUPACC_MSK |
-			ETHER_ARC_CTL_STATIONACC_MSK,
-			ETHER_ARC_CTL(dev->base_addr));
-		return;
-	}
-
-	/*
-	 * Get all multicast packets if required, or if there are too
-	 * many addresses to fit in hardware
-	 */
-	if (dev->flags & IFF_ALLMULTI){
-		writew( ETHER_ARC_CTL_COMPEN_MSK |
-			ETHER_ARC_CTL_GROUPACC_MSK |
-			ETHER_ARC_CTL_BROADACC_MSK,
-			ETHER_ARC_CTL(dev->base_addr));
-		return;
-	}
-	if (dev->mc_count > (ETHER_ARC_SIZE - 1)){
-
-		printk(KERN_WARNING "Too many multicast addresses for hardware to filter - receiving all multicast packets\n");
-		writew( ETHER_ARC_CTL_COMPEN_MSK |
-			ETHER_ARC_CTL_GROUPACC_MSK |
-			ETHER_ARC_CTL_BROADACC_MSK,
-			ETHER_ARC_CTL(dev->base_addr));
-		return;
-	}
-
-	if(dev->mc_count){
-		struct dev_mc_list *mc_list_ent=dev->mc_list;
-		unsigned int temp,i;
-		DEBUG(printk("mc_count=%d mc_list=%#x\n",dev-> mc_count, dev->mc_list));
-		DEBUG(printk("mc addr=%02#x%02x%02x%02x%02x%02x\n",
-			     mc_list_ent->dmi_addr[5],
-			     mc_list_ent->dmi_addr[4],
-			     mc_list_ent->dmi_addr[3],
-			     mc_list_ent->dmi_addr[2],
-			     mc_list_ent->dmi_addr[1],
-			     mc_list_ent->dmi_addr[0]);)
-
-		/*
-		 * The first 6 bytes are the MAC address, so
-		 * don't change them!
-		 */
-		writew(4,ETHER_ARC_ADR(dev->base_addr));
-		temp=readl(ETHER_ARC_DATA(dev->base_addr));
-		temp&=0xffff0000;
-
-		/* Disable the current multicast stuff */
-		writel(1,ETHER_ARC_ENA(dev->base_addr));
-
-		for(;;){
-			temp|=mc_list_ent->dmi_addr[1] |
-				mc_list_ent->dmi_addr[0]<<8;
-			writel(temp,ETHER_ARC_DATA(dev->base_addr));
-
-			i=readl(ETHER_ARC_ADR(dev->base_addr));
-			writew(i+4,ETHER_ARC_ADR(dev->base_addr));
-
-			temp=mc_list_ent->dmi_addr[5]|
-				mc_list_ent->dmi_addr[4]<<8 |
-				mc_list_ent->dmi_addr[3]<<16 |
-				mc_list_ent->dmi_addr[2]<<24;
-			writel(temp,ETHER_ARC_DATA(dev->base_addr));
-
-			count--;
-			if(!mc_list_ent->next || !count){
-				break;
-			}
-			DEBUG(printk("mc_list_next=%#x\n",mc_list_ent->next);)
-			mc_list_ent=mc_list_ent->next;
-
-
-			i=readl(ETHER_ARC_ADR(dev->base_addr));
-			writel(i+4,ETHER_ARC_ADR(dev->base_addr));
-
-			temp=mc_list_ent->dmi_addr[3]|
-				mc_list_ent->dmi_addr[2]<<8 |
-				mc_list_ent->dmi_addr[1]<<16 |
-				mc_list_ent->dmi_addr[0]<<24;
-			writel(temp,ETHER_ARC_DATA(dev->base_addr));
-
-			i=readl(ETHER_ARC_ADR(dev->base_addr));
-			writel(i+4,ETHER_ARC_ADR(dev->base_addr));
-
-			temp=mc_list_ent->dmi_addr[4]<<16 |
-				mc_list_ent->dmi_addr[5]<<24;
-
-			writel(temp,ETHER_ARC_DATA(dev->base_addr));
-
-			count--;
-			if(!mc_list_ent->next || !count){
-				break;
-			}
-			mc_list_ent=mc_list_ent->next;
-		}
-
-
-		if(count)
-			printk(KERN_WARNING "Multicast list size error\n");
-
-
-		writew( ETHER_ARC_CTL_BROADACC_MSK|
-			ETHER_ARC_CTL_COMPEN_MSK,
-			ETHER_ARC_CTL(dev->base_addr));
-
-	}
-
-	/* enable the active ARC enties */
-	writew((1<<(count+2))-1,ETHER_ARC_ENA(dev->base_addr));
-}
-
-
-static int ether00_open(struct net_device* dev)
-{
-	int result,tmp;
-	struct net_priv* priv;
-
-	if (!is_valid_ether_addr(dev->dev_addr))
-		return -EINVAL;
-
-	/* Install interrupt handlers */
-	result=request_irq(dev->irq,ether00_int,0,"ether00",dev);
-	if(result)
-		goto open_err1;
-
-	result=request_irq(2,ether00_phy_int,0,"ether00_phy",dev);
-	if(result)
-		goto open_err2;
-
-	ether00_reset(dev);
-	result=ether00_mem_init(dev);
-	if(result)
-		goto open_err3;
-
-
-	ether00_setup_ethernet_address(dev);
-
-	ether00_set_multicast(dev);
-
-	result=ether00_write_phy(dev,PHY_CONTROL, PHY_CONTROL_ANEGEN_MSK | PHY_CONTROL_RANEG_MSK);
-	if(result)
-		goto open_err4;
-	result=ether00_write_phy(dev,PHY_IRQ_CONTROL, PHY_IRQ_CONTROL_LS_CHG_IE_MSK |
-				 PHY_IRQ_CONTROL_ANEG_COMP_IE_MSK);
-	if(result)
-		goto open_err4;
-
-	/* Start the device enable interrupts */
-	writew(ETHER_RX_CTL_RXEN_MSK
-//	       | ETHER_RX_CTL_STRIPCRC_MSK
-	       | ETHER_RX_CTL_ENGOOD_MSK
-	       | ETHER_RX_CTL_ENRXPAR_MSK| ETHER_RX_CTL_ENLONGERR_MSK
-	       | ETHER_RX_CTL_ENOVER_MSK| ETHER_RX_CTL_ENCRCERR_MSK,
-	       ETHER_RX_CTL(dev->base_addr));
-
-	writew(ETHER_TX_CTL_TXEN_MSK|
-	       ETHER_TX_CTL_ENEXDEFER_MSK|
-	       ETHER_TX_CTL_ENLCARR_MSK|
-	       ETHER_TX_CTL_ENEXCOLL_MSK|
-	       ETHER_TX_CTL_ENLATECOLL_MSK|
-	       ETHER_TX_CTL_ENTXPAR_MSK|
-	       ETHER_TX_CTL_ENCOMP_MSK,
-	       ETHER_TX_CTL(dev->base_addr));
-
-	tmp=readl(ETHER_DMA_CTL(dev->base_addr));
-	writel(tmp&~ETHER_DMA_CTL_INTMASK_MSK,ETHER_DMA_CTL(dev->base_addr));
-
-	return 0;
-
- open_err4:
-	ether00_reset(dev);
- open_err3:
-	free_irq(2,dev);
- open_err2:
-	free_irq(dev->irq,dev);
- open_err1:
-	return result;
-
-}
-
-
-static int ether00_tx(struct sk_buff* skb, struct net_device* dev)
-{
-	struct net_priv *priv=dev->priv;
-	struct tx_fda_ent *fda_ptr;
-	int i;
-
-
-	/*
-	 *	Find an empty slot in which to stick the frame
-	 */
-	fda_ptr=(struct tx_fda_ent*)__dma_va(readl(ETHER_TXFRMPTR(dev->base_addr)));
-	i=0;
-	while(i<TX_NUM_FDESC){
-		if (fda_ptr->fd.FDStat||(fda_ptr->fd.FDCtl & FDCTL_COWNSFD_MSK)){
-			fda_ptr =(struct tx_fda_ent*) __dma_va((struct tx_fda_ent*)fda_ptr->fd.FDNext);
-		}
-		else {
-			break;
-		}
-		i++;
-	}
-
-	/* Write the skb data from the cache*/
-	consistent_sync(skb->data,skb->len,PCI_DMA_TODEVICE);
-	fda_ptr->bd.BuffData=(char*)__pa(skb->data);
-	fda_ptr->bd.BuffLength=(unsigned short)skb->len;
-	/* Save the pointer to the skb for freeing later */
-	fda_ptr->fd.FDSystem=(unsigned int)skb;
-	fda_ptr->fd.FDStat=0;
-	/* Pass