Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ahci: redo stopping DMA engines on empty ports
  sata_sil24: fix kernel panic on ARM caused by unaligned access in sata_sil24
  ahci: add pci quirk for JMB362
  sata_via: explain the magic fix

4 files changed, 29 insertions, 27 deletions

diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c
index 1984a6e89e8..261f86d102e 100644
--- a/drivers/ata/libahci.c
+++ b/drivers/ata/libahci.c
@@ -541,29 +541,11 @@ static int ahci_scr_write(struct ata_link *link, unsigned int sc_reg, u32 val)
 	return -EINVAL;
 }
 
-static int ahci_is_device_present(void __iomem *port_mmio)
-{
-	u8 status = readl(port_mmio + PORT_TFDATA) & 0xff;
-
-	/* Make sure PxTFD.STS.BSY and PxTFD.STS.DRQ are 0 */
-	if (status & (ATA_BUSY | ATA_DRQ))
-		return 0;
-
-	/* Make sure PxSSTS.DET is 3h */
-	status = readl(port_mmio + PORT_SCR_STAT) & 0xf;
-	if (status != 3)
-		return 0;
-	return 1;
-}
-
 void ahci_start_engine(struct ata_port *ap)
 {
 	void __iomem *port_mmio = ahci_port_base(ap);
 	u32 tmp;
 
-	if (!ahci_is_device_present(port_mmio))
-		return;
-
 	/* start DMA */
 	tmp = readl(port_mmio + PORT_CMD);
 	tmp |= PORT_CMD_START;
@@ -1892,6 +1874,9 @@ static void ahci_error_handler(struct ata_port *ap)
 	}
 
 	sata_pmp_error_handler(ap);
+
+	if (!ata_dev_enabled(ap->link.device))
+		ahci_stop_engine(ap);
 }
 
 static void ahci_post_internal_cmd(struct ata_queued_cmd *qc)
diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c
index e9250514734..70b58fe9e5b 100644
--- a/drivers/ata/sata_sil24.c
+++ b/drivers/ata/sata_sil24.c
@@ -539,12 +539,12 @@ static void sil24_config_port(struct ata_port *ap)
 		writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_CLR);
 
 	/* zero error counters. */
-	writel(0x8000, port + PORT_DECODE_ERR_THRESH);
-	writel(0x8000, port + PORT_CRC_ERR_THRESH);
-	writel(0x8000, port + PORT_HSHK_ERR_THRESH);
-	writel(0x0000, port + PORT_DECODE_ERR_CNT);
-	writel(0x0000, port + PORT_CRC_ERR_CNT);
-	writel(0x0000, port + PORT_HSHK_ERR_CNT);
+	writew(0x8000, port + PORT_DECODE_ERR_THRESH);
+	writew(0x8000, port + PORT_CRC_ERR_THRESH);
+	writew(0x8000, port + PORT_HSHK_ERR_THRESH);
+	writew(0x0000, port + PORT_DECODE_ERR_CNT);
+	writew(0x0000, port + PORT_CRC_ERR_CNT);
+	writew(0x0000, port + PORT_HSHK_ERR_CNT);
 
 	/* always use 64bit activation */
 	writel(PORT_CS_32BIT_ACTV, port + PORT_CTRL_CLR);
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index 0ecd0f6aa2c..4730c42a5ee 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -578,10 +578,24 @@ static void svia_configure(struct pci_dev *pdev)
 
 	/*
 	 * vt6421 has problems talking to some drives.  The following
-	 * is the magic fix from Joseph Chan <JosephChan@via.com.tw>.
-	 * Please add proper documentation if possible.
+	 * is the fix from Joseph Chan <JosephChan@via.com.tw>.
+	 *
+	 * When host issues HOLD, device may send up to 20DW of data
+	 * before acknowledging it with HOLDA and the host should be
+	 * able to buffer them in FIFO.  Unfortunately, some WD drives
+	 * send upto 40DW before acknowledging HOLD and, in the
+	 * default configuration, this ends up overflowing vt6421's
+	 * FIFO, making the controller abort the transaction with
+	 * R_ERR.
+	 *
+	 * Rx52[2] is the internal 128DW FIFO Flow control watermark
+	 * adjusting mechanism enable bit and the default value 0
+	 * means host will issue HOLD to device when the left FIFO
+	 * size goes below 32DW.  Setting it to 1 makes the watermark
+	 * 64DW.
 	 *
 	 * https://bugzilla.kernel.org/show_bug.cgi?id=15173
+	 * http://article.gmane.org/gmane.linux.ide/46352
 	 */
 	if (pdev->device == 0x3249) {
 		pci_read_config_byte(pdev, 0x52, &tmp8);
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index b7512cf08c5..477345d4164 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -1457,7 +1457,8 @@ static void quirk_jmicron_ata(struct pci_dev *pdev)
 	conf5 &= ~(1 << 24);  /* Clear bit 24 */
 
 	switch (pdev->device) {
-	case PCI_DEVICE_ID_JMICRON_JMB360:
+	case PCI_DEVICE_ID_JMICRON_JMB360: /* SATA single port */
+	case PCI_DEVICE_ID_JMICRON_JMB362: /* SATA dual ports */
 		/* The controller should be in single function ahci mode */
 		conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */
 		break;
@@ -1493,12 +1494,14 @@ static void quirk_jmicron_ata(struct pci_dev *pdev)
 }
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata);
 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata);
 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata);
+DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata);
 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata);
 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata);
 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata);