Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
  rtc: max8925: Add function to work as wakeup source
  mfd: Add pm ops to max8925
  mfd: Convert aat2870 to dev_pm_ops
  mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
  mfd: Introduce missing kfree in 88pm860x probe routine
  mfd: Add S5M series configuration
  mfd: Add s5m series irq driver
  mfd: Add S5M core driver
  mfd: Improve mc13xxx dt binding document
  mfd: Fix stmpe section mismatch
  mfd: Fix stmpe build warning
  mfd: Fix STMPE I2c build failure
  mfd: Constify aat2870-core i2c_device_id table
  gpio: Add support for stmpe variant 801
  mfd: Add support for stmpe variant 801
  mfd: Add support for stmpe variant 610
  mfd: Add support for STMPE SPI interface
  mfd: Separate out STMPE controller and interface specific code
  misc: Remove max8997-muic sysfs attributes
  mfd: Remove unused wm831x_irq_data_to_mask_reg()
  ...

Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.

67 files changed, 2722 insertions, 532 deletions

diff --git a/drivers/gpio/gpio-stmpe.c b/drivers/gpio/gpio-stmpe.c
index 4c980b57332..87a68a896ab 100644
--- a/drivers/gpio/gpio-stmpe.c
+++ b/drivers/gpio/gpio-stmpe.c
@@ -65,7 +65,14 @@ static void stmpe_gpio_set(struct gpio_chip *chip, unsigned offset, int val)
 	u8 reg = stmpe->regs[which] - (offset / 8);
 	u8 mask = 1 << (offset % 8);
 
-	stmpe_reg_write(stmpe, reg, mask);
+	/*
+	 * Some variants have single register for gpio set/clear functionality.
+	 * For them we need to write 0 to clear and 1 to set.
+	 */
+	if (stmpe->regs[STMPE_IDX_GPSR_LSB] == stmpe->regs[STMPE_IDX_GPCR_LSB])
+		stmpe_set_bits(stmpe, reg, mask, val ? mask : 0);
+	else
+		stmpe_reg_write(stmpe, reg, mask);
 }
 
 static int stmpe_gpio_direction_output(struct gpio_chip *chip,
@@ -132,6 +139,10 @@ static int stmpe_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 	if (type == IRQ_TYPE_LEVEL_LOW || type == IRQ_TYPE_LEVEL_HIGH)
 		return -EINVAL;
 
+	/* STMPE801 doesn't have RE and FE registers */
+	if (stmpe_gpio->stmpe->partnum == STMPE801)
+		return 0;
+
 	if (type == IRQ_TYPE_EDGE_RISING)
 		stmpe_gpio->regs[REG_RE][regoffset] |= mask;
 	else
@@ -165,6 +176,11 @@ static void stmpe_gpio_irq_sync_unlock(struct irq_data *d)
 	int i, j;
 
 	for (i = 0; i < CACHE_NR_REGS; i++) {
+		/* STMPE801 doesn't have RE and FE registers */
+		if ((stmpe->partnum == STMPE801) &&
+				(i != REG_IE))
+			continue;
+
 		for (j = 0; j < num_banks; j++) {
 			u8 old = stmpe_gpio->oldregs[i][j];
 			u8 new = stmpe_gpio->regs[i][j];
@@ -241,8 +257,11 @@ static irqreturn_t stmpe_gpio_irq(int irq, void *dev)
 		}
 
 		stmpe_reg_write(stmpe, statmsbreg + i, status[i]);
-		stmpe_reg_write(stmpe, stmpe->regs[STMPE_IDX_GPEDR_MSB] + i,
-				status[i]);
+
+		/* Edge detect register is not present on 801 */
+		if (stmpe->partnum != STMPE801)
+			stmpe_reg_write(stmpe, stmpe->regs[STMPE_IDX_GPEDR_MSB]
+					+ i, status[i]);
 	}
 
 	return IRQ_HANDLED;
diff --git a/drivers/input/misc/ab8500-ponkey.c b/drivers/input/misc/ab8500-ponkey.c
index 79d90163363..350fd0c385d 100644
--- a/drivers/input/misc/ab8500-ponkey.c
+++ b/drivers/input/misc/ab8500-ponkey.c
@@ -12,7 +12,7 @@
 #include <linux/platform_device.h>
 #include <linux/input.h>
 #include <linux/interrupt.h>
-#include <linux/mfd/ab8500.h>
+#include <linux/mfd/abx500/ab8500.h>
 #include <linux/slab.h>
 
 /**
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 897a77dfa9d..c957c344233 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -396,6 +396,13 @@ config LEDS_TCA6507
 	  LED driver chips accessed via the I2C bus.
 	  Driver support brightness control and hardware-assisted blinking.
 
+config LEDS_MAX8997
+	tristate "LED support for MAX8997 PMIC"
+	depends on LEDS_CLASS && MFD_MAX8997
+	help
+	  This option enables support for on-chip LED drivers on
+	  MAXIM MAX8997 PMIC.
+
 config LEDS_TRIGGERS
 	bool "LED Trigger support"
 	depends on LEDS_CLASS
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index 5c9dc4b000d..b8a9723477f 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -44,6 +44,7 @@ obj-$(CONFIG_LEDS_NS2)			+= leds-ns2.o
 obj-$(CONFIG_LEDS_NETXBIG)		+= leds-netxbig.o
 obj-$(CONFIG_LEDS_ASIC3)		+= leds-asic3.o
 obj-$(CONFIG_LEDS_RENESAS_TPU)		+= leds-renesas-tpu.o
+obj-$(CONFIG_LEDS_MAX8997)		+= leds-max8997.o
 
 # LED SPI Drivers
 obj-$(CONFIG_LEDS_DAC124S085)		+= leds-dac124s085.o
diff --git a/drivers/leds/leds-max8997.c b/drivers/leds/leds-max8997.c
new file mode 100644
index 00000000000..f4c0e37fad1
--- /dev/null
+++ b/drivers/leds/leds-max8997.c
@@ -0,0 +1,372 @@
+/*
+ * leds-max8997.c - LED class driver for MAX8997 LEDs.
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ * Donggeun Kim <dg77.kim@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/workqueue.h>
+#include <linux/leds.h>
+#include <linux/mfd/max8997.h>
+#include <linux/mfd/max8997-private.h>
+#include <linux/platform_device.h>
+
+#define MAX8997_LED_FLASH_SHIFT			3
+#define MAX8997_LED_FLASH_CUR_MASK		0xf8
+#define MAX8997_LED_MOVIE_SHIFT			4
+#define MAX8997_LED_MOVIE_CUR_MASK		0xf0
+
+#define MAX8997_LED_FLASH_MAX_BRIGHTNESS	0x1f
+#define MAX8997_LED_MOVIE_MAX_BRIGHTNESS	0xf
+#define MAX8997_LED_NONE_MAX_BRIGHTNESS		0
+
+#define MAX8997_LED0_FLASH_MASK			0x1
+#define MAX8997_LED0_FLASH_PIN_MASK		0x5
+#define MAX8997_LED0_MOVIE_MASK			0x8
+#define MAX8997_LED0_MOVIE_PIN_MASK		0x28
+
+#define MAX8997_LED1_FLASH_MASK			0x2
+#define MAX8997_LED1_FLASH_PIN_MASK		0x6
+#define MAX8997_LED1_MOVIE_MASK			0x10
+#define MAX8997_LED1_MOVIE_PIN_MASK		0x30
+
+#define MAX8997_LED_BOOST_ENABLE_MASK		(1 << 6)
+
+struct max8997_led {
+	struct max8997_dev *iodev;
+	struct led_classdev cdev;
+	bool enabled;
+	int id;
+	enum max8997_led_mode led_mode;
+	struct mutex mutex;
+};
+
+static void max8997_led_clear_mode(struct max8997_led *led,
+			enum max8997_led_mode mode)
+{
+	struct i2c_client *client = led->iodev->i2c;
+	u8 val = 0, mask = 0;
+	int ret;
+
+	switch (mode) {
+	case MAX8997_FLASH_MODE:
+		mask = led->id ?
+		      MAX8997_LED1_FLASH_MASK : MAX8997_LED0_FLASH_MASK;
+		break;
+	case MAX8997_MOVIE_MODE:
+		mask = led->id ?
+		      MAX8997_LED1_MOVIE_MASK : MAX8997_LED0_MOVIE_MASK;
+		break;
+	case MAX8997_FLASH_PIN_CONTROL_MODE:
+		mask = led->id ?
+		      MAX8997_LED1_FLASH_PIN_MASK : MAX8997_LED0_FLASH_PIN_MASK;
+		break;
+	case MAX8997_MOVIE_PIN_CONTROL_MODE:
+		mask = led->id ?
+		      MAX8997_LED1_MOVIE_PIN_MASK : MAX8997_LED0_MOVIE_PIN_MASK;
+		break;
+	default:
+		break;
+	}
+
+	if (mask) {
+		ret = max8997_update_reg(client,
+				MAX8997_REG_LEN_CNTL, val, mask);
+		if (ret)
+			dev_err(led->iodev->dev,
+				"failed to update register(%d)\n", ret);
+	}
+}
+
+static void max8997_led_set_mode(struct max8997_led *led,
+			enum max8997_led_mode mode)
+{
+	int ret;
+	struct i2c_client *client = led->iodev->i2c;
+	u8 mask = 0;
+
+	/* First, clear the previous mode */
+	max8997_led_clear_mode(led, led->led_mode);
+
+	switch (mode) {
+	case MAX8997_FLASH_MODE:
+		mask = led->id ?
+		      MAX8997_LED1_FLASH_MASK : MAX8997_LED0_FLASH_MASK;
+		led->cdev.max_brightness = MAX8997_LED_FLASH_MAX_BRIGHTNESS;
+		break;
+	case MAX8997_MOVIE_MODE:
+		mask = led->id ?
+		      MAX8997_LED1_MOVIE_MASK : MAX8997_LED0_MOVIE_MASK;
+		led->cdev.max_brightness = MAX8997_LED_MOVIE_MAX_BRIGHTNESS;
+		break;
+	case MAX8997_FLASH_PIN_CONTROL_MODE:
+		mask = led->id ?
+		      MAX8997_LED1_FLASH_PIN_MASK : MAX8997_LED0_FLASH_PIN_MASK;
+		led->cdev.max_brightness = MAX8997_LED_FLASH_MAX_BRIGHTNESS;
+		break;
+	case MAX8997_MOVIE_PIN_CONTROL_MODE:
+		mask = led->id ?
+		      MAX8997_LED1_MOVIE_PIN_MASK : MAX8997_LED0_MOVIE_PIN_MASK;
+		led->cdev.max_brightness = MAX8997_LED_MOVIE_MAX_BRIGHTNESS;
+		break;
+	default:
+		led->cdev.max_brightness = MAX8997_LED_NONE_MAX_BRIGHTNESS;
+		break;
+	}
+
+	if (mask) {
+		ret = max8997_update_reg(client,
+				MAX8997_REG_LEN_CNTL, mask, mask);
+		if (ret)
+			dev_err(led->iodev->dev,
+				"failed to update register(%d)\n", ret);
+	}
+
+	led->led_mode = mode;
+}
+
+static void max8997_led_enable(struct max8997_led *led, bool enable)
+{
+	int ret;
+	struct i2c_client *client = led->iodev->i2c;
+	u8 val = 0, mask = MAX8997_LED_BOOST_ENABLE_MASK;
+
+	if (led->enabled == enable)
+		return;
+
+	val = enable ? MAX8997_LED_BOOST_ENABLE_MASK : 0;
+
+	ret = max8997_update_reg(client, MAX8997_REG_BOOST_CNTL, val, mask);
+	if (ret)
+		dev_err(led->iodev->dev,
+			"failed to update register(%d)\n", ret);
+
+	led->enabled = enable;
+}
+
+static void max8997_led_set_current(struct max8997_led *led,
+				enum led_brightness value)
+{
+	int ret;
+	struct i2c_client *client = led->iodev->i2c;
+	u8 val = 0, mask = 0, reg = 0;
+
+	switch (led->led_mode) {
+	case MAX8997_FLASH_MODE:
+	case MAX8997_FLASH_PIN_CONTROL_MODE:
+		val = value << MAX8997_LED_FLASH_SHIFT;
+		mask = MAX8997_LED_FLASH_CUR_MASK;
+		reg = led->id ? MAX8997_REG_FLASH2_CUR : MAX8997_REG_FLASH1_CUR;
+		break;
+	case MAX8997_MOVIE_MODE:
+	case MAX8997_MOVIE_PIN_CONTROL_MODE:
+		val = value << MAX8997_LED_MOVIE_SHIFT;
+		mask = MAX8997_LED_MOVIE_CUR_MASK;
+		reg = MAX8997_REG_MOVIE_CUR;
+		break;
+	default:
+		break;
+	}
+
+	if (mask) {
+		ret = max8997_update_reg(client, reg, val, mask);
+		if (ret)
+			dev_err(led->iodev->dev,
+				"failed to update register(%d)\n", ret);
+	}
+}
+
+static void max8997_led_brightness_set(struct led_classdev *led_cdev,
+				enum led_brightness value)
+{
+	struct max8997_led *led =
+			container_of(led_cdev, struct max8997_led, cdev);
+
+	if (value) {
+		max8997_led_set_current(led, value);
+		max8997_led_enable(led, true);
+	} else {
+		max8997_led_set_current(led, value);
+		max8997_led_enable(led, false);
+	}
+}
+
+static ssize_t max8997_led_show_mode(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct led_classdev *led_cdev = dev_get_drvdata(dev);
+	struct max8997_led *led =
+			container_of(led_cdev, struct max8997_led, cdev);
+	ssize_t ret = 0;
+
+	mutex_lock(&led->mutex);
+
+	switch (led->led_mode) {
+	case MAX8997_FLASH_MODE:
+		ret += sprintf(buf, "FLASH\n");
+		break;
+	case MAX8997_MOVIE_MODE:
+		ret += sprintf(buf, "MOVIE\n");
+		break;
+	case MAX8997_FLASH_PIN_CONTROL_MODE:
+		ret += sprintf(buf, "FLASH_PIN_CONTROL\n");
+		break;
+	case MAX8997_MOVIE_PIN_CONTROL_MODE:
+		ret += sprintf(buf, "MOVIE_PIN_CONTROL\n");
+		break;
+	default:
+		ret += sprintf(buf, "NONE\n");
+		break;
+	}
+
+	mutex_unlock(&led->mutex);
+
+	return ret;
+}
+
+static ssize_t max8997_led_store_mode(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t size)
+{
+	struct led_classdev *led_cdev = dev_get_drvdata(dev);
+	struct max8997_led *led =
+			container_of(led_cdev, struct max8997_led, cdev);
+	enum max8997_led_mode mode;
+
+	mutex_lock(&led->mutex);
+
+	if (!strncmp(buf, "FLASH_PIN_CONTROL", 17))
+		mode = MAX8997_FLASH_PIN_CONTROL_MODE;
+	else if (!strncmp(buf, "MOVIE_PIN_CONTROL", 17))
+		mode = MAX8997_MOVIE_PIN_CONTROL_MODE;
+	else if (!strncmp(buf, "FLASH", 5))
+		mode = MAX8997_FLASH_MODE;
+	else if (!strncmp(buf, "MOVIE", 5))
+		mode = MAX8997_MOVIE_MODE;
+	else
+		mode = MAX8997_NONE;
+
+	max8997_led_set_mode(led, mode);
+
+	mutex_unlock(&led->mutex);
+
+	return size;
+}
+
+static DEVICE_ATTR(mode, 0644, max8997_led_show_mode, max8997_led_store_mode);
+
+static int __devinit max8997_led_probe(struct platform_device *pdev)
+{
+	struct max8997_dev *iodev = dev_get_drvdata(pdev->dev.parent);
+	struct max8997_platform_data *pdata = dev_get_platdata(iodev->dev);
+	struct max8997_led *led;
+	char name[20];
+	int ret = 0;
+
+	if (pdata == NULL) {
+		dev_err(&pdev->dev, "no platform data\n");
+		return -ENODEV;
+	}
+
+	led = kzalloc(sizeof(*led), GFP_KERNEL);
+	if (led == NULL) {
+		ret = -ENOMEM;
+		goto err_mem;
+	}
+
+	led->id = pdev->id;
+	snprintf(name, sizeof(name), "max8997-led%d", pdev->id);
+
+	led->cdev.name = name;
+	led->cdev.brightness_set = max8997_led_brightness_set;
+	led->cdev.flags |= LED_CORE_SUSPENDRESUME;
+	led->cdev.brightness = 0;
+	led->iodev = iodev;
+
+	/* initialize mode and brightness according to platform_data */
+	if (pdata->led_pdata) {
+		u8 mode = 0, brightness = 0;
+
+		mode = pdata->led_pdata->mode[led->id];
+		brightness = pdata->led_pdata->brightness[led->id];
+
+		max8997_led_set_mode(led, pdata->led_pdata->mode[led->id]);
+
+		if (brightness > led->cdev.max_brightness)
+			brightness = led->cdev.max_brightness;
+		max8997_led_set_current(led, brightness);
+		led->cdev.brightness = brightness;
+	} else {
+		max8997_led_set_mode(led, MAX8997_NONE);
+		max8997_led_set_current(led, 0);
+	}
+
+	mutex_init(&led->mutex);
+
+	platform_set_drvdata(pdev, led);
+
+	ret = led_classdev_register(&pdev->dev, &led->cdev);
+	if (ret < 0)
+		goto err_led;
+
+	ret = device_create_file(led->cdev.dev, &dev_attr_mode);
+	if (ret != 0) {
+		dev_err(&pdev->dev,
+			"failed to create file: %d\n", ret);
+		goto err_file;
+	}
+
+	return 0;
+
+err_file:
+	led_classdev_unregister(&led->cdev);
+err_led:
+	kfree(led);
+err_mem:
+	return ret;
+}
+
+static int __devexit max8997_led_remove(struct platform_device *pdev)
+{
+	struct max8997_led *led = platform_get_drvdata(pdev);
+
+	device_remove_file(led->cdev.dev, &dev_attr_mode);
+	led_classdev_unregister(&led->cdev);
+	kfree(led);
+
+	return 0;
+}
+
+static struct platform_driver max8997_led_driver = {
+	.driver = {
+		.name  = "max8997-led",
+		.owner = THIS_MODULE,
+	},
+	.probe  = max8997_led_probe,
+	.remove = __devexit_p(max8997_led_remove),
+};
+
+static int __init max8997_led_init(void)
+{
+	return platform_driver_register(&max8997_led_driver);
+}
+module_init(max8997_led_init);
+
+static void __exit max8997_led_exit(void)
+{
+	platform_driver_unregister(&max8997_led_driver);
+}
+module_exit(max8997_led_exit);
+
+MODULE_AUTHOR("Donggeun Kim <dg77.kim@samsung.com>");
+MODULE_DESCRIPTION("MAX8997 LED driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:max8997-led");
diff --git a/drivers/mfd/88pm860x-i2c.c b/drivers/mfd/88pm860x-i2c.c
index e017dc88622..f93dd9571c3 100644
--- a/drivers/mfd/88pm860x-i2c.c
+++ b/drivers/mfd/88pm860x-i2c.c
@@ -12,51 +12,20 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/i2c.h>
+#include <linux/err.h>
+#include <linux/regmap.h>
 #include <linux/mfd/88pm860x.h>
 #include <linux/slab.h>
 
-static inline int pm860x_read_device(struct i2c_client *i2c,
-				     int reg, int bytes, void *dest)
-{
-	unsigned char data;
-	int ret;
-
-	data = (unsigned char)reg;
-	ret = i2c_master_send(i2c, &data, 1);
-	if (ret < 0)
-		return ret;
-
-	ret = i2c_master_recv(i2c, dest, bytes);
-	if (ret < 0)
-		return ret;
-	return 0;
-}
-
-static inline int pm860x_write_device(struct i2c_client *i2c,
-				      int reg, int bytes, void *src)
-{
-	unsigned char buf[bytes + 1];
-	int ret;
-
-	buf[0] = (unsigned char)reg;
-	memcpy(&buf[1], src, bytes);
-
-	ret = i2c_master_send(i2c, buf, bytes + 1);
-	if (ret < 0)
-		return ret;
-	return 0;
-}
-
 int pm860x_reg_read(struct i2c_client *i2c, int reg)
 {
 	struct pm860x_chip *chip = i2c_get_clientdata(i2c);
-	unsigned char data;
+	struct regmap *map = (i2c == chip->client) ? chip->regmap
+				: chip->regmap_companion;
+	unsigned int data;
 	int ret;
 
-	mutex_lock(&chip->io_lock);
-	ret = pm860x_read_device(i2c, reg, 1, &data);
-	mutex_unlock(&chip->io_lock);
-
+	ret = regmap_read(map, reg, &data);
 	if (ret < 0)
 		return ret;
 	else
@@ -68,12 +37,11 @@ int pm860x_reg_write(struct i2c_client *i2c, int reg,
 		     unsigned char data)
 {
 	struct pm860x_chip *chip = i2c_get_clientdata(i2c);
+	struct regmap *map = (i2c == chip->client) ? chip->regmap
+				: chip->regmap_companion;
 	int ret;
 
-	mutex_lock(&chip->io_lock);
-	ret = pm860x_write_device(i2c, reg, 1, &data);
-	mutex_unlock(&chip->io_lock);
-
+	ret = regmap_write(map, reg, data);
 	return ret;
 }
 EXPORT_SYMBOL(pm860x_reg_write);
@@ -82,12 +50,11 @@ int pm860x_bulk_read(struct i2c_client *i2c, int reg,
 		     int count, unsigned char *buf)
 {
 	struct pm860x_chip *chip = i2c_get_clientdata(i2c);
+	struct regmap *map = (i2c == chip->client) ? chip->regmap
+				: chip->regmap_companion;
 	int ret;
 
-	mutex_lock(&chip->io_lock);
-	ret = pm860x_read_device(i2c, reg, count, buf);
-	mutex_unlock(&chip->io_lock);
-
+	ret = regmap_raw_read(map, reg, buf, count);
 	return ret;
 }
 EXPORT_SYMBOL(pm860x_bulk_read);
@@ -96,12 +63,11 @@ int pm860x_bulk_write(struct i2c_client *i2c, int reg,
 		      int count, unsigned char *buf)
 {
 	struct pm860x_chip *chip = i2c_get_clientdata(i2c);
+	struct regmap *map = (i2c == chip->client) ? chip->regmap
+				: chip->regmap_companion;