Merge branch 'from-linus'

73 files changed, 1104 insertions, 1846 deletions

diff --git a/drivers/acpi/Kconfig b/drivers/acpi/Kconfig
index 0cce28c4025..33e2ca847a2 100644
--- a/drivers/acpi/Kconfig
+++ b/drivers/acpi/Kconfig
@@ -247,7 +247,7 @@ config ACPI_CUSTOM_DSDT_FILE
 	  Enter the full path name to the file wich includes the AmlCode declaration.
 
 config ACPI_BLACKLIST_YEAR
-	int "Disable ACPI for systems before Jan 1st this year" if X86
+	int "Disable ACPI for systems before Jan 1st this year" if X86_32
 	default 0
 	help
 	  enter a 4-digit year, eg. 2001 to disable ACPI by default
@@ -285,9 +285,8 @@ config ACPI_SYSTEM
 	  dump your ACPI DSDT table using /proc/acpi/dsdt.
 
 config X86_PM_TIMER
-	bool "Power Management Timer Support"
+	bool "Power Management Timer Support" if EMBEDDED
 	depends on X86
-	depends on !X86_64
 	default y
 	help
 	  The Power Management Timer is available on all ACPI-capable,
@@ -298,9 +297,8 @@ config X86_PM_TIMER
 	  voltage scaling, unlike the commonly used Time Stamp Counter
 	  (TSC) timing source.
 
-	  So, if you see messages like 'Losing too many ticks!' in the
-	  kernel logs, and/or you are using this on a notebook which
-	  does not yet have an HPET, you should say "Y" here.
+	  You should nearly always say Y here because many modern
+	  systems require this timer. 
 
 config ACPI_CONTAINER
 	tristate "ACPI0004,PNP0A05 and PNP0A06 Container Driver (EXPERIMENTAL)"
diff --git a/drivers/acpi/resources/rscalc.c b/drivers/acpi/resources/rscalc.c
index 7d6481d9fbe..4038dbfa63a 100644
--- a/drivers/acpi/resources/rscalc.c
+++ b/drivers/acpi/resources/rscalc.c
@@ -391,8 +391,7 @@ acpi_rs_get_list_length(u8 * aml_buffer,
 			 * Ensure a 32-bit boundary for the structure
 			 */
 			extra_struct_bytes =
-			    ACPI_ROUND_UP_to_32_bITS(resource_length) -
-			    resource_length;
+			    ACPI_ROUND_UP_to_32_bITS(resource_length);
 			break;
 
 		case ACPI_RESOURCE_NAME_END_TAG:
@@ -408,8 +407,7 @@ acpi_rs_get_list_length(u8 * aml_buffer,
 			 * Add vendor data and ensure a 32-bit boundary for the structure
 			 */
 			extra_struct_bytes =
-			    ACPI_ROUND_UP_to_32_bITS(resource_length) -
-			    resource_length;
+			    ACPI_ROUND_UP_to_32_bITS(resource_length);
 			break;
 
 		case ACPI_RESOURCE_NAME_ADDRESS32:
diff --git a/drivers/block/pktcdvd.c b/drivers/block/pktcdvd.c
index 93e44d0292a..bc9b2bcd7db 100644
--- a/drivers/block/pktcdvd.c
+++ b/drivers/block/pktcdvd.c
@@ -58,6 +58,7 @@
 #include <linux/suspend.h>
 #include <scsi/scsi_cmnd.h>
 #include <scsi/scsi_ioctl.h>
+#include <scsi/scsi.h>
 
 #include <asm/uaccess.h>
 
@@ -380,6 +381,7 @@ static int pkt_generic_packet(struct pktcdvd_device *pd, struct packet_command *
 	memcpy(rq->cmd, cgc->cmd, CDROM_PACKET_SIZE);
 	if (sizeof(rq->cmd) > CDROM_PACKET_SIZE)
 		memset(rq->cmd + CDROM_PACKET_SIZE, 0, sizeof(rq->cmd) - CDROM_PACKET_SIZE);
+	rq->cmd_len = COMMAND_SIZE(rq->cmd[0]);
 
 	rq->ref_count++;
 	rq->flags |= REQ_NOMERGE;
@@ -1495,40 +1497,42 @@ static int pkt_set_write_settings(struct pktcdvd_device *pd)
 }
 
 /*
- * 0 -- we can write to this track, 1 -- we can't
+ * 1 -- we can write to this track, 0 -- we can't
  */
-static int pkt_good_track(track_information *ti)
+static int pkt_writable_track(struct pktcdvd_device *pd, track_information *ti)
 {
-	/*
-	 * only good for CD-RW at the moment, not DVD-RW
-	 */
+	switch (pd->mmc3_profile) {
+		case 0x1a: /* DVD+RW */
+		case 0x12: /* DVD-RAM */
+			/* The track is always writable on DVD+RW/DVD-RAM */
+			return 1;
+		default:
+			break;
+	}
 
-	/*
-	 * FIXME: only for FP
-	 */
-	if (ti->fp == 0)
+	if (!ti->packet || !ti->fp)
 		return 0;
 
 	/*
 	 * "good" settings as per Mt Fuji.
 	 */
-	if (ti->rt == 0 && ti->blank == 0 && ti->packet == 1)
-		return 0;
+	if (ti->rt == 0 && ti->blank == 0)
+		return 1;
 
-	if (ti->rt == 0 && ti->blank == 1 && ti->packet == 1)
-		return 0;
+	if (ti->rt == 0 && ti->blank == 1)
+		return 1;
 
-	if (ti->rt == 1 && ti->blank == 0 && ti->packet == 1)
-		return 0;
+	if (ti->rt == 1 && ti->blank == 0)
+		return 1;
 
 	printk("pktcdvd: bad state %d-%d-%d\n", ti->rt, ti->blank, ti->packet);
-	return 1;
+	return 0;
 }
 
 /*
- * 0 -- we can write to this disc, 1 -- we can't
+ * 1 -- we can write to this disc, 0 -- we can't
  */
-static int pkt_good_disc(struct pktcdvd_device *pd, disc_information *di)
+static int pkt_writable_disc(struct pktcdvd_device *pd, disc_information *di)
 {
 	switch (pd->mmc3_profile) {
 		case 0x0a: /* CD-RW */
@@ -1537,10 +1541,10 @@ static int pkt_good_disc(struct pktcdvd_device *pd, disc_information *di)
 		case 0x1a: /* DVD+RW */
 		case 0x13: /* DVD-RW */
 		case 0x12: /* DVD-RAM */
-			return 0;
+			return 1;
 		default:
 			VPRINTK("pktcdvd: Wrong disc profile (%x)\n", pd->mmc3_profile);
-			return 1;
+			return 0;
 	}
 
 	/*
@@ -1549,25 +1553,25 @@ static int pkt_good_disc(struct pktcdvd_device *pd, disc_information *di)
 	 */
 	if (di->disc_type == 0xff) {
 		printk("pktcdvd: Unknown disc. No track?\n");
-		return 1;
+		return 0;
 	}
 
 	if (di->disc_type != 0x20 && di->disc_type != 0) {
 		printk("pktcdvd: Wrong disc type (%x)\n", di->disc_type);
-		return 1;
+		return 0;
 	}
 
 	if (di->erasable == 0) {
 		printk("pktcdvd: Disc not erasable\n");
-		return 1;
+		return 0;
 	}
 
 	if (di->border_status == PACKET_SESSION_RESERVED) {
 		printk("pktcdvd: Can't write to last track (reserved)\n");
-		return 1;
+		return 0;
 	}
 
-	return 0;
+	return 1;
 }
 
 static int pkt_probe_settings(struct pktcdvd_device *pd)
@@ -1592,23 +1596,9 @@ static int pkt_probe_settings(struct pktcdvd_device *pd)
 		return ret;
 	}
 
-	if (pkt_good_disc(pd, &di))
-		return -ENXIO;
+	if (!pkt_writable_disc(pd, &di))
+		return -EROFS;
 
-	switch (pd->mmc3_profile) {
-		case 0x1a: /* DVD+RW */
-			printk("pktcdvd: inserted media is DVD+RW\n");
-			break;
-		case 0x13: /* DVD-RW */
-			printk("pktcdvd: inserted media is DVD-RW\n");
-			break;
-		case 0x12: /* DVD-RAM */
-			printk("pktcdvd: inserted media is DVD-RAM\n");
-			break;
-		default:
-			printk("pktcdvd: inserted media is CD-R%s\n", di.erasable ? "W" : "");
-			break;
-	}
 	pd->type = di.erasable ? PACKET_CDRW : PACKET_CDR;
 
 	track = 1; /* (di.last_track_msb << 8) | di.last_track_lsb; */
@@ -1617,9 +1607,9 @@ static int pkt_probe_settings(struct pktcdvd_device *pd)
 		return ret;
 	}
 
-	if (pkt_good_track(&ti)) {
+	if (!pkt_writable_track(pd, &ti)) {
 		printk("pktcdvd: can't write to this track\n");
-		return -ENXIO;
+		return -EROFS;
 	}
 
 	/*
@@ -1633,7 +1623,7 @@ static int pkt_probe_settings(struct pktcdvd_device *pd)
 	}
 	if (pd->settings.size > PACKET_MAX_SECTORS) {
 		printk("pktcdvd: packet size is too big\n");
-		return -ENXIO;
+		return -EROFS;
 	}
 	pd->settings.fp = ti.fp;
 	pd->offset = (be32_to_cpu(ti.track_start) << 2) & (pd->settings.size - 1);
@@ -1675,7 +1665,7 @@ static int pkt_probe_settings(struct pktcdvd_device *pd)
 			break;
 		default:
 			printk("pktcdvd: unknown data mode\n");
-			return 1;
+			return -EROFS;
 	}
 	return 0;
 }
@@ -1886,7 +1876,7 @@ static int pkt_open_write(struct pktcdvd_device *pd)
 
 	if ((ret = pkt_probe_settings(pd))) {
 		VPRINTK("pktcdvd: %s failed probe\n", pd->name);
-		return -EROFS;
+		return ret;
 	}
 
 	if ((ret = pkt_set_write_settings(pd))) {
diff --git a/drivers/char/agp/Kconfig b/drivers/char/agp/Kconfig
index 486ed8a11b5..a4d425d2dce 100644
--- a/drivers/char/agp/Kconfig
+++ b/drivers/char/agp/Kconfig
@@ -15,22 +15,23 @@ config AGP
 	  due to kernel allocation issues), you could use PCI accesses
 	  and have up to a couple gigs of texture space.
 
-	  Note that this is the only means to have XFree4/GLX use
+	  Note that this is the only means to have X/GLX use
 	  write-combining with MTRR support on the AGP bus. Without it, OpenGL
 	  direct rendering will be a lot slower but still faster than PIO.
 
-	  You should say Y here if you use XFree86 3.3.6 or 4.x and want to
-	  use GLX or DRI.  If unsure, say N.
-
 	  To compile this driver as a module, choose M here: the
 	  module will be called agpgart.
 
+	  You should say Y here if you want to use GLX or DRI.
+
+	  If unsure, say N.
+
 config AGP_ALI
 	tristate "ALI chipset support"
 	depends on AGP && X86_32
 	---help---
 	  This option gives you AGP support for the GLX component of
-	  XFree86 4.x on the following ALi chipsets.  The supported chipsets
+	  X on the following ALi chipsets.  The supported chipsets
 	  include M1541, M1621, M1631, M1632, M1641,M1647,and M1651.
 	  For the ALi-chipset question, ALi suggests you refer to
 	  <http://www.ali.com.tw/eng/support/index.shtml>.
@@ -40,28 +41,19 @@ config AGP_ALI
 	  timing issues, this chipset cannot do AGP 2x with the G200.
 	  This is a hardware limitation. AGP 1x seems to be fine, though.
 
-	  You should say Y here if you use XFree86 3.3.6 or 4.x and want to
-	  use GLX or DRI.  If unsure, say N.
-
 config AGP_ATI
 	tristate "ATI chipset support"
 	depends on AGP && X86_32
 	---help---
-      This option gives you AGP support for the GLX component of
-      XFree86 4.x on the ATI RadeonIGP family of chipsets.
-
-      You should say Y here if you use XFree86 3.3.6 or 4.x and want to
-      use GLX or DRI.  If unsure, say N.
+	  This option gives you AGP support for the GLX component of
+	  X on the ATI RadeonIGP family of chipsets.
 
 config AGP_AMD
 	tristate "AMD Irongate, 761, and 762 chipset support"
 	depends on AGP && X86_32
 	help
 	  This option gives you AGP support for the GLX component of
-	  XFree86 4.x on AMD Irongate, 761, and 762 chipsets.
-
-	  You should say Y here if you use XFree86 3.3.6 or 4.x and want to
-	  use GLX or DRI.  If unsure, say N.
+	  X on AMD Irongate, 761, and 762 chipsets.
 
 config AGP_AMD64
 	tristate "AMD Opteron/Athlon64 on-CPU GART support" if !GART_IOMMU
@@ -69,45 +61,38 @@ config AGP_AMD64
 	default y if GART_IOMMU
 	help
 	  This option gives you AGP support for the GLX component of
-	  XFree86 4.x using the on-CPU northbridge of the AMD Athlon64/Opteron CPUs.
+	  X using the on-CPU northbridge of the AMD Athlon64/Opteron CPUs.
 	  You still need an external AGP bridge like the AMD 8151, VIA
           K8T400M, SiS755. It may also support other AGP bridges when loaded
 	  with agp_try_unsupported=1.
-	  You should say Y here if you use XFree86 3.3.6 or 4.x and want to
-	  use GLX or DRI.  If unsure, say Y
 
 config AGP_INTEL
 	tristate "Intel 440LX/BX/GX, I8xx and E7x05 chipset support"
 	depends on AGP && X86
 	help
-	  This option gives you AGP support for the GLX component of XFree86 4.x
+	  This option gives you AGP support for the GLX component of X
 	  on Intel 440LX/BX/GX, 815, 820, 830, 840, 845, 850, 860, 875,
-	  E7205 and E7505 chipsets and full support for the 810, 815, 830M, 845G,
-	  852GM, 855GM, 865G and I915 integrated graphics chipsets.
+	  E7205 and E7505 chipsets and full support for the 810, 815, 830M,
+	  845G, 852GM, 855GM, 865G and I915 integrated graphics chipsets.
+
 
-	  You should say Y here if you use XFree86 3.3.6 or 4.x and want to
-	  use GLX or DRI, or if you have any Intel integrated graphics
-	  chipsets.  If unsure, say Y.
 
 config AGP_NVIDIA
 	tristate "NVIDIA nForce/nForce2 chipset support"
 	depends on AGP && X86_32
 	help
 	  This option gives you AGP support for the GLX component of
-	  XFree86 4.x on the following NVIDIA chipsets.  The supported chipsets
-	  include nForce and nForce2
+	  X on NVIDIA chipsets including nForce and nForce2
 
 config AGP_SIS
 	tristate "SiS chipset support"
 	depends on AGP && X86_32
 	help
 	  This option gives you AGP support for the GLX component of
-	  XFree86 4.x on Silicon Integrated Systems [SiS] chipsets.
+	  X on Silicon Integrated Systems [SiS] chipsets.
 
 	  Note that 5591/5592 AGP chipsets are NOT supported.
 
-	  You should say Y here if you use XFree86 3.3.6 or 4.x and want to
-	  use GLX or DRI.  If unsure, say N.
 
 config AGP_SWORKS
 	tristate "Serverworks LE/HE chipset support"
@@ -121,10 +106,7 @@ config AGP_VIA
 	depends on AGP && X86_32
 	help
 	  This option gives you AGP support for the GLX component of
-	  XFree86 4.x on VIA MVP3/Apollo Pro chipsets.
-
-	  You should say Y here if you use XFree86 3.3.6 or 4.x and want to
-	  use GLX or DRI.  If unsure, say N.
+	  X on VIA MVP3/Apollo Pro chipsets.
 
 config AGP_I460
 	tristate "Intel 460GX chipset support"
@@ -159,9 +141,6 @@ config AGP_EFFICEON
 	  This option gives you AGP support for the Transmeta Efficeon
 	  series processors with integrated northbridges.
 
-	  You should say Y here if you use XFree86 3.3.6 or 4.x and want to
-	  use GLX or DRI.  If unsure, say Y.
-
 config AGP_SGI_TIOCA
         tristate "SGI TIO chipset AGP support"
         depends on AGP && (IA64_SGI_SN2 || IA64_GENERIC)
diff --git a/drivers/char/agp/amd64-agp.c b/drivers/char/agp/amd64-agp.c
index 9964c508c11..1251b2515bb 100644
--- a/drivers/char/agp/amd64-agp.c
+++ b/drivers/char/agp/amd64-agp.c
@@ -516,8 +516,10 @@ static int __devinit nforce3_agp_init(struct pci_dev *pdev)
 	pci_read_config_dword (hammers[0], AMD64_GARTAPERTUREBASE, &apbase);
 
 	/* if x86-64 aperture base is beyond 4G, exit here */
-	if ( (apbase & 0x7fff) >> (32 - 25) )
-		 return -ENODEV;
+	if ( (apbase & 0x7fff) >> (32 - 25) ) {
+		printk(KERN_INFO PFX "aperture base > 4G\n");
+		return -ENODEV;
+	}
 
 	apbase = (apbase & 0x7fff) << 25;
 
diff --git a/drivers/char/agp/sworks-agp.c b/drivers/char/agp/sworks-agp.c
index 268f78d926d..efef9999f1c 100644
--- a/drivers/char/agp/sworks-agp.c
+++ b/drivers/char/agp/sworks-agp.c
@@ -468,9 +468,7 @@ static int __devinit agp_serverworks_probe(struct pci_dev *pdev,
 
 	switch (pdev->device) {
 	case 0x0006:
-		/* ServerWorks CNB20HE
-		Fail silently.*/
-		printk (KERN_ERR PFX "Detected ServerWorks CNB20HE chipset: No AGP present.\n");
+		printk (KERN_ERR PFX "ServerWorks CNB20HE is unsupported due to lack of documentation.\n");
 		return -ENODEV;
 
 	case PCI_DEVICE_ID_SERVERWORKS_HE:
diff --git a/drivers/char/drm/i915_irq.c b/drivers/char/drm/i915_irq.c
index a1381c61aa6..d3879ac9970 100644
--- a/drivers/char/drm/i915_irq.c
+++ b/drivers/char/drm/i915_irq.c
@@ -202,10 +202,15 @@ void i915_driver_irq_postinstall(drm_device_t * dev)
 void i915_driver_irq_uninstall(drm_device_t * dev)
 {
 	drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
+	u16 temp;
+
 	if (!dev_priv)
 		return;
 
 	I915_WRITE16(I915REG_HWSTAM, 0xffff);
 	I915_WRITE16(I915REG_INT_MASK_R, 0xffff);
 	I915_WRITE16(I915REG_INT_ENABLE_R, 0x0);
+
+	temp = I915_READ16(I915REG_INT_IDENTITY_R);
+	I915_WRITE16(I915REG_INT_IDENTITY_R, temp);
 }
diff --git a/drivers/char/drm/r300_cmdbuf.c b/drivers/char/drm/r300_cmdbuf.c
index 291dbf4c818..c08fa5076f0 100644
--- a/drivers/char/drm/r300_cmdbuf.c
+++ b/drivers/char/drm/r300_cmdbuf.c
@@ -161,6 +161,7 @@ void r300_init_reg_flags(void)
 	ADD_RANGE(R300_VAP_PVS_CNTL_1, 3);
 	ADD_RANGE(R300_GB_ENABLE, 1);
 	ADD_RANGE(R300_GB_MSPOS0, 5);
+	ADD_RANGE(R300_TX_CNTL, 1);
 	ADD_RANGE(R300_TX_ENABLE, 1);
 	ADD_RANGE(0x4200, 4);
 	ADD_RANGE(0x4214, 1);
@@ -489,6 +490,50 @@ static __inline__ int r300_emit_3d_load_vbpntr(drm_radeon_private_t *dev_priv,
 
 	return 0;
 }
+static __inline__ int r300_emit_bitblt_multi(drm_radeon_private_t *dev_priv,
+					     drm_radeon_kcmd_buffer_t *cmdbuf)
+{
+	u32 *cmd = (u32 *) cmdbuf->buf;
+	int count, ret;
+	RING_LOCALS;
+
+	count=(cmd[0]>>16) & 0x3fff;
+
+	if (cmd[0] & 0x8000) {
+		u32 offset;
+
+		if (cmd[1] & (RADEON_GMC_SRC_PITCH_OFFSET_CNTL 
+			      | RADEON_GMC_DST_PITCH_OFFSET_CNTL)) {
+			offset = cmd[2] << 10;
+			ret = r300_check_offset(dev_priv, offset);
+			if (ret) {
+				DRM_ERROR("Invalid bitblt first offset is %08X\n", offset);
+				return DRM_ERR(EINVAL);
+			}
+		}
+
+		if ((cmd[1] & RADEON_GMC_SRC_PITCH_OFFSET_CNTL) &&
+		    (cmd[1] & RADEON_GMC_DST_PITCH_OFFSET_CNTL)) {
+			offset = cmd[3] << 10;
+			ret = r300_check_offset(dev_priv, offset);
+			if (ret) {
+				DRM_ERROR("Invalid bitblt second offset is %08X\n", offset);
+				return DRM_ERR(EINVAL);
+			}
+			
+		}
+	}
+
+	BEGIN_RING(count+2);
+	OUT_RING(cmd[0]);
+	OUT_RING_TABLE((int *)(cmdbuf->buf + 4), count + 1);
+	ADVANCE_RING();
+
+	cmdbuf->buf += (count+2)*4;
+	cmdbuf->bufsz -= (count+2)*4;
+
+	return 0;
+}
 
 static __inline__ int r300_emit_raw_packet3(drm_radeon_private_t *dev_priv,
 					    drm_radeon_kcmd_buffer_t *cmdbuf)
@@ -527,6 +572,9 @@ static __inline__ int r300_emit_raw_packet3(drm_radeon_private_t *dev_priv,
 	case RADEON_3D_LOAD_VBPNTR:	/* load vertex array pointers */
 		return r300_emit_3d_load_vbpntr(dev_priv, cmdbuf, header);
 
+	case RADEON_CNTL_BITBLT_MULTI:
+		return r300_emit_bitblt_multi(dev_priv, cmdbuf);
+
 	case RADEON_CP_3D_DRAW_IMMD_2:	/* triggers drawing using in-packet vertex data */
 	case RADEON_CP_3D_DRAW_VBUF_2:	/* triggers drawing of vertex buffers setup elsewhere */
 	case RADEON_CP_3D_DRAW_INDX_2:	/* triggers drawing using indices to vertex buffer */
diff --git a/drivers/char/drm/r300_reg.h b/drivers/char/drm/r300_reg.h
index a0ed20e2522..d1e19954406 100644
--- a/drivers/char/drm/r300_reg.h
+++ b/drivers/char/drm/r300_reg.h
@@ -451,6 +451,9 @@ I am fairly certain that they are correct unless stated otherwise in comments.
 /* END */
 
 /* gap */
+/* Zero to flush caches. */
+#define R300_TX_CNTL                        0x4100
+
 /* The upper enable bits are guessed, based on fglrx reported limits. */
 #define R300_TX_ENABLE                      0x4104
 #       define R300_TX_ENABLE_0                  (1 << 0)
diff --git a/drivers/char/drm/radeon_drv.h b/drivers/char/drm/radeon_drv.h
index 498b19b1d64..1f7d2ab8c4f 100644
--- a/drivers/char/drm/radeon_drv.h
+++ b/drivers/char/drm/radeon_drv.h
@@ -90,9 +90,10 @@
  * 1.19- Add support for gart table in FB memory and PCIE r300
  * 1.20- Add support for r300 texrect
  * 1.21- Add support for card type getparam
+ * 1.22- Add support for texture cache flushes (R300_TX_CNTL)
  */
 #define DRIVER_MAJOR		1
-#define DRIVER_MINOR		21
+#define DRIVER_MINOR		22
 #define DRIVER_PATCHLEVEL	0
 
 /*
diff --git a/drivers/char/hvc_console.c b/drivers/char/hvc_console.c
index 1994a92d473..f65b2e14a48 100644
--- a/drivers/char/hvc_console.c
+++ b/drivers/char/hvc_console.c
@@ -335,6 +335,8 @@ static int hvc_open(struct tty_struct *tty, struct file * filp)
 	} /* else count == 0 */
 
 	tty->driver_data = hp;
+	tty->low_latency = 1; /* Makes flushes to ldisc synchronous. */
+
 	hp->tty = tty;
 	/* Save for request_irq outside of spin_lock. */
 	irq = hp->irq;
@@ -633,9 +635,6 @@ static int hvc_poll(struct hvc_struct *hp)
 			tty_insert_flip_char(tty, buf[i], 0);
 		}
 
-		if (count)
-			tty_schedule_flip(tty);
-
 		/*
 		 * Account for the total amount read in one loop, and if above
 		 * 64 bytes, we do a quick schedule loop to let the tty grok
@@ -656,6 +655,9 @@ static int hvc_poll(struct hvc_struct *hp)
  bail:
 	spin_unlock_irqrestore(&hp->lock, flags);
 
+	if (read_total)
+		tty_flip_buffer_push(tty);
+	
 	return poll_mask;
 }
 
diff --git a/drivers/char/sx.c b/drivers/char/sx.c
index c2490e270f1..a6b4f02bdce 100644
--- a/drivers/char/sx.c
+++ b/drivers/char/sx.c
@@ -1095,17 +1095,17 @@ static inline void sx_receive_chars (struct sx_port *port)
 
 		sx_dprintk (SX_DEBUG_RECEIVE, "rxop=%d, c = %d.\n", rx_op, c); 
 
+		/* Don't copy past the end of the hardware receive buffer */
+		if (rx_op + c > 0x100) c = 0x100 - rx_op;
+
+		sx_dprintk (SX_DEBUG_RECEIVE, "c = %d.\n", c);
+
 		/* Don't copy more bytes than there is room for in the buffer */
 
 		c = tty_prepare_flip_string(tty, &rp, c);
 
 		sx_dprintk (SX_DEBUG_RECEIVE, "c = %d.\n", c); 
 
-		/* Don't copy past the end of the hardware receive buffer */
-		if (rx_op + c > 0x100) c = 0x100 - rx_op;
-
-		sx_dprintk (SX_DEBUG_RECEIVE, "c = %d.\n", c);
-
 		/* If for one reason or another, we can't copy more data, we're done! */
 		if (c == 0) break;
 
@@ -2173,15 +2173,17 @@ static int probe_si (struct sx_board *board)
 	if ( IS_SI1_BOARD(board)) {
 		/* This should be an SI1 board, which has this
 		   location writable... */
-		if (read_sx_byte (board, SI2_ISA_ID_BASE) != 0x10)
+		if (read_sx_byte (board, SI2_ISA_ID_BASE) != 0x10) {
 			func_exit ();
 			return 0; 
+		}
 	} else {
 		/* This should be an SI2 board, which has the bottom
 		   3 bits non-writable... */
-		if (read_sx_byte (board, SI2_ISA_ID_BASE) == 0x10)
+		if (read_sx_byte (board, SI2_ISA_ID_BASE) == 0x10) {
 			func_exit ();
 			return 0; 
+		}
 	}
 
 	/* Now we're pretty much convinced that there is an SI board here, 
@@ -2192,15 +2194,17 @@ static int probe_si (struct sx_board *board)
 	if ( IS_SI1_BOARD(board)) {
 		/* This should be an SI1 board, which has this
 		   location writable... */
-		if (read_sx_byte (board, SI2_ISA_ID_BASE) != 0x10)
+		if (read_sx_byte (board, SI2_ISA_ID_BASE) != 0x10) {
 			func_exit();
 			return 0; 
+		}
 	} else {
 		/* This should be an SI2 board, which has the bottom
 		   3 bits non-writable... */
-		if (read_sx_byte (board, SI2_ISA_ID_BASE) == 0x10)
+		if (read_sx_byte (board, SI2_ISA_ID_BASE) == 0x10) {
 			func_exit ();
 			return 0; 
+		}
 	}
 
 	printheader ();
diff --git a/drivers/char/sysrq.c b/drivers/char/sysrq.c
index 5765f672e85..d58f8231885 100644
--- a/drivers/char/sysrq.c
+++ b/drivers/char/sysrq.c
@@ -243,7 +243,7 @@ static struct sysrq_key_op sysrq_term_op = {
 
 static void moom_callback(void *ignored)
 {
-	out_of_memory(GFP_KERNEL, 0);
+	out_of_memory(&NODE_DATA(0)->node_zonelists[ZONE_NORMAL], GFP_KERNEL, 0);
 }
 
 static DECLARE_WORK(moom_work, moom_callback, NULL);
diff --git a/drivers/char/tpm/tpm_infineon.c b/drivers/char/tpm/tpm_infineon.c
index ec7590951af..24095f6ee6d 100644
--- a/drivers/char/tpm/tpm_infineon.c
+++ b/drivers/char/tpm/tpm_infineon.c
@@ -33,6 +33,7 @@
 static int TPM_INF_DATA;
 static int TPM_INF_ADDR;
 static int TPM_INF_BASE;
+static int TPM_INF_ADDR_LEN;
 static int TPM_INF_PORT_LEN;
 
 /* TPM header definitions */
@@ -195,6 +196,7 @@ static int tpm_inf_recv(struct tpm_chip *chip, u8 * buf, size_t count)
 	int i;
 	int ret;
 	u32 size = 0;
+	number_of_wtx = 0;
 
 recv_begin:
 	/* start receiving header */
@@ -378,24 +380,35 @@ static int __devinit tpm_inf_pnp_probe(struct pnp_dev *dev,
 	if (pnp_port_valid(dev, 0) && pnp_port_valid(dev, 1) &&
 	    !(pnp_port_flags(dev, 0) & IORESOURCE_DISABLED)) {
 		TPM_INF_ADDR = pnp_port_start(dev, 0);
+		TPM_INF_ADDR_LEN = pnp_port_len(dev, 0);
 		TPM_INF_DATA = (TPM_INF_ADDR + 1);
 		TPM_INF_BASE = pnp_port_start(dev, 1);
 		TPM_INF_PORT_LEN = pnp_port_len(dev, 1);
-		if (!TPM_INF_PORT_LEN)
-			return -EINVAL;
+		if ((TPM_INF_PORT_LEN < 4) || (TPM_INF_ADDR_LEN < 2)) {
+			rc = -EINVAL;
+			goto err_last;
+		}
 		dev_info(&dev->dev, "Found %s with ID %s\n",
 			 dev->name, dev_id->id);
-		if (!((TPM_INF_BASE >> 8) & 0xff))
-			return -EINVAL;
+		if (!((TPM_INF_BASE >> 8) & 0xff)) {
+			rc = -EINVAL;
+			goto err_last;
+		}
 		/* publish my base address and request region */
 		tpm_inf.base = TPM_INF_BASE;
 		if (request_region
 		    (tpm_inf.base, TPM_INF_PORT_LEN, "tpm_infineon0") == NULL) {
-			release_region(tpm_inf.base, TPM_INF_PORT_LEN);
-			return -EINVAL;
+			rc = -EINVAL;
+			goto err_last;
+		}
+		if (request_region(TPM_INF_ADDR, TPM_INF_ADDR_LEN,
+				"tpm_infineon0") == NULL) {
+			rc = -EINVAL;
+			goto err_last;
 		}
 	} else {
-		return -EINVAL;
+		rc = -EINVAL;
+		goto err_last;
 	}
 
 	/* query chip for its vendor, its version number a.s.o. */
@@ -443,8 +456,8 @@ static int __devinit tpm_inf_pnp_probe(struct pnp_dev *dev,
 			dev_err(&dev->dev,
 				"Could not set IO-ports to 0x%lx\n",
 				tpm_inf.base);
-			release_region(tpm_inf.base, TPM_INF_PORT_LEN);
-			return -EIO;
+			rc = -EIO;
+			goto err_release_region;
 		}
 
 		/* activate register */
@@ -471,14 +484,21 @@ static int __devinit tpm_inf_pnp_probe(struct pnp_dev *dev,
 
 		rc = tpm_register_hardware(&dev->dev, &tpm_inf);
 		if (rc < 0) {
-			release_region(tpm_inf.base, TPM_INF_PORT_LEN);
-			return -ENODEV;
+			rc = -ENODEV;
+			goto err_release_region;
 		}
 		return 0;
 	} else {
-		dev_info(&dev->dev, "No Infineon TPM found!\n");
-		return -ENODEV;
+		rc = -ENODEV;
+		goto err_release_region;
 	}
+
+err_release_region:
+	release_region(tpm_inf.base, TPM_INF_PORT_LEN);
+	release_region(TPM_INF_ADDR, TPM_INF_ADDR_LEN);
+
+err_last:
+	return rc;
 }
 
 static __devexit void tpm_inf_pnp_remove(struct pnp_dev *dev)
@@ -518,5 +538,5 @@ module_exit(cleanup_inf);
 
 MODULE_AUTHOR("Marcel Selhorst <selhorst@crypto.rub.de>");
 MODULE_DESCRIPTION("Driver for Infineon TPM SLD 9630 TT 1.1 / SLB 9635 TT 1.2");
-MODULE_VERSION("1.6");
+MODULE_VERSION("1.7");
 MODULE_LICENSE("GPL");
diff --git a/drivers/crypto/padlock-aes.c b/drivers/crypto/padlock-aes.c
index 64819aa7cac..0c08c58252b 100644
--- a/drivers/crypto/padlock-aes.c
+++ b/drivers/crypto/padlock-aes.c
@@ -348,10 +348,10 @@ aes_set_key(void *ctx_arg, const uint8_t *in_key, unsigned int key_len, uint32_t
 		break;
 
 	case 32:
-		E_KEY[4] = le32_to_cpu(in_key[4]);
-		E_KEY[5] = le32_to_cpu(in_key[5]);
-		E_KEY[6] = le32_to_cpu(in_key[6]);
-		t = E_KEY[7] = le32_to_cpu(in_key[7]);
+		E_KEY[4] = le32_to_cpu(key[4]);
+		E_KEY[5] = le32_to_cpu(key[5]);
+		E_KEY[6] = le32_to_cpu(key[6]);
+		t = E_KEY[7] = le32_to_cpu(key[7]);
 		for (i = 0; i < 7; ++i)
 			loop8 (i);
 		break;
diff --git a/drivers/fc4/fc.c b/drivers/fc4/fc.c
index 5c8943509cc..66d03f242d3 100644
--- a/drivers/fc4/fc.c
+++ b/drivers/fc4/fc.c
@@ -1053,7 +1053,7 @@ static int fc_do_els(fc_channel *fc, unsigned int alpa, void *data, int len)
 	int i;
 
 	fcmd = &_fcmd;
-	memset(fcmd, 0, sizeof(fcmd));
+	memset(fcmd, 0, sizeof(fcp_cmnd));
 	FCD(("PLOGI SID %d DID %d\n", fc->sid, alpa))
 	fch = &fcmd->fch;
 	FILL_FCHDR_RCTL_DID(fch, R_CTL_ELS_REQ, alpa);
diff --git a/drivers/ide/pci/sgiioc4.c b/drivers/ide/pci/sgiioc4.c
index 2b286e86516..43b96e29836 100644
--- a/drivers/ide/pci/sgiioc4.c
+++ b/drivers/ide/pci/sgiioc4.c
@@ -13,11 +13,6 @@
  * License along with this program; if not, write the Free Software
  * Foundation, Inc., 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
  *
- * Contact information:  Silicon Graphics, Inc., 1600 Amphitheatre Pkwy,
- * Mountain View, CA  94043, or:
- *
- * http://www.sgi.com
- *
  * For further information regarding this notice, see:
  *
  * http://oss.sgi.com/projects/GenInfo/NoticeExplan
diff --git a/drivers/ieee1394/sbp2.c b/drivers/ieee1394/sbp2.c
index 18d7eda3885..eca92eb475a 100644
--- a/drivers/ieee1394/sbp2.c
+++ b/drivers/ieee1394/sbp2.c
@@ -137,15 +137,15 @@ MODULE_PARM_DESC(exclusive_login, "Exclusive login to sbp2 device (default = 1)"
 /*
  * SCSI inquiry hack for really badly behaved sbp2 devices. Turn this on
  * if your sbp2 device is not properly handling the SCSI inquiry command.
- * This hack makes the inquiry look more like a typical MS Windows
- * inquiry.
+ * This hack makes the inquiry look more like a typical MS Windows inquiry
+ * by enforcing 36 byte inquiry and avoiding access to mode_sense page 8.
  *
  * If force_inquiry_hack=1 is required for your device to work,
  * please submit the logged sbp2_firmware_revision value of this device to
  * the linux1394-devel mailing list.
  */
 static int force_inquiry_hack;
-module_param(force_inquiry_hack, int, 0444);
+module_param(force_inquiry_hack, int, 0644);
 MODULE_PARM_DESC(force_inquiry_hack, "Force SCSI inquiry hack (default = 0)");
 
 /*
@@ -264,18 +264,17 @@ static struct hpsb_protocol_driver sbp2_driver = {
 	},
 };
 
-
-/* List of device firmware's that require a forced 36 byte inquiry.  */
+/*
+ * List of device firmwares that require the inquiry hack.
+ * Yields a few false positives but did not break other devices so far.
+ */
 static u32 sbp2_broken_inquiry_list[] = {
-	0x00002800,	/* Stefan Richter <richtest@bauwesen.tu-cottbus.de> */
+	0x00002800,	/* Stefan Richter <stefanr@s5r6.in-berlin.de> */
 			/* DViCO Momobay CX-1 */
 	0x00000200	/* Andreas Plesch <plesch@fas.harvard.edu> */
 			/* QPS Fire DVDBurner */
 };
 
-#define NUM_BROKEN_INQUIRY_DEVS \
-	(sizeof(sbp2_broken_inquiry_list)/sizeof(*sbp2_broken_inquiry_list))
-
 /**************************************
  * General utility functions
  **************************************/
@@ -643,9 +642,15 @@ static int sbp2_remove(struct device *dev)
 	if (!scsi_id)
 		return 0;
 
-	/* Trigger shutdown functions in scsi's highlevel. */
-	if (scsi_id->scsi_host)
+	if (scsi_id->scsi_host) {
+		/* Get rid of enqueued commands if there is no chance to
+		 * send them. */
+		if (!sbp2util_node_is_available(scsi_id))
+			sbp2scsi_complete_all_commands(scsi_id, DID_NO_CONNECT);
+		/* scsi_remove_device() will trigger shutdown functions of SCSI
+		 * highlevel drivers which would deadlock if blocked. */
 		scsi_unblock_requests(scsi_id->scsi_host);
+	}
 	sdev = scsi_id->sdev;
 	if (sdev) {
 		scsi_id->sdev = NULL;
@@ -742,11 +747,6 @@ static struct scsi_id_instance_data *sbp2_alloc_device(struct unit_directory *ud
 		hi->host = ud->ne->host;
 		INIT_LIST_HEAD(&hi->scsi_ids);
 
-		/* Register our sbp2 status address space... */
-		hpsb_register_addrspace(&sbp2_highlevel, ud->ne->host, &sbp2_ops,
-					SBP2_STATUS_FIFO_ADDRESS,
-					SBP2_STATUS_FIFO_ADDRESS +
-					SBP2_STATUS_FIFO_ENTRY_TO_OFFSET(SBP2_MAX_UDS_PER_NODE+1));
 #ifdef CONFIG_IEEE1394_SBP2_PHYS_DMA
 		/* Handle data movement if physical dma is not
 		 * enabled/supportedon host controller */
@@ -759,6 +759,18 @@ static struct scsi_id_instance_data *sbp2_alloc_device(struct unit_directory *ud
 
 	list_add_tail(&scsi_id->scsi_list, &hi->scsi_ids);
 
+	/* Register the status FIFO address range. We could use the same FIFO
+	 * for targets at different nodes. However we need different FIFOs per
+	 * target in order to support multi-unit devices. */
+	scsi_id->status_fifo_addr = hpsb_allocate_and_register_addrspace(
+			&sbp2_highlevel, ud->ne->host, &sbp2_ops,
+			sizeof(struct sbp2_status_block), sizeof(quadlet_t),
+			~0ULL, ~0ULL);
+	if (!scsi_id->status_fifo_addr) {
+		SBP2_ERR("failed to allocate status FIFO address range");
+		goto failed_alloc;
+	}
+
 	/* Register our host with the SCSI stack. */
 	scsi_host = scsi_host_alloc(&scsi_driver_template,
 				    sizeof(unsigned long));
@@ -997,6 +1009,10 @@ static void sbp2_remove_device(struct scsi_id_instance_data *scsi_id)
 		SBP2_DMA_FREE("single query logins data");
 	}
 
+	if (scsi_id->status_fifo_addr)
+		hpsb_unregister_addrspace(&sbp2_highlevel, hi->host,
+			scsi_id->status_fifo_addr);
+
 	scsi_id->ud->device.driver_data = NULL;
 
 	SBP2_DEBUG("SBP-2 device removed, SCSI ID = %d", scsi_id->ud->id);
@@ -1075,11 +1091,10 @@ static int sbp2_query_logins(struct scsi_id_instance_data *scsi_id)
 		ORB_SET_QUERY_LOGINS_RESP_LENGTH(sizeof(struct sbp2_query_logins_response));
 	SBP2_DEBUG("sbp2_query_logins: reserved_resp_length initialized");
 
-	scsi_id->query_logins_orb->status_FIFO_lo = SBP2_STATUS_FIFO_ADDRESS_LO +
-						    SBP2_STATUS_FIFO_ENTRY_TO_OFFSET(scsi_id->ud->id);
-	scsi_id->query_logins_orb->status_FIFO_hi = (ORB_SET_NODE_ID(hi->host->node_id) |
-						     SBP2_STATUS_FIFO_ADDRESS_HI);
-	SBP2_DEBUG("sbp2_query_logins: status FIFO initialized");
+	scsi_id->query_logins_orb->status_fifo_hi =
+		ORB_SET_STATUS_FIFO_HI(scsi_id->status_fifo_addr, hi->host->node_id);
+	scsi_id->query_logins_orb->status_fifo_lo =
+		ORB_SET_STATUS_FIFO_LO(scsi_id->status_fifo_addr);
 
 	sbp2util_cpu_to_be32_buffer(scsi_id->query_logins_orb, sizeof(struct sbp2_query_logins_orb));
 
@@ -1184,11 +1199,10 @@ static int sbp2_login_device(struct scsi_id_instance_data *scsi_id)
 		ORB_SET_LOGIN_RESP_LENGTH(sizeof(struct sbp2_login_response));
 	SBP2_DEBUG("sbp2_login_device: passwd_resp_lengths initialized");
 
-	scsi_id->login_orb->status_FIFO_lo = SBP2_STATUS_FIFO_ADDRESS_LO +
-					     SBP2_STATUS_FIFO_ENTRY_TO_OFFSET(scsi_id->ud->id);
-	scsi_id->login_orb->status_FIFO_hi = (ORB_SET_NODE_ID(hi->host->node_id) |
-					      SBP2_STATUS_FIFO_ADDRESS_HI);
-	SBP2_DEBUG("sbp2_login_device: status FIFO initialized");
+	scsi_id->login_orb->status_fifo_hi =
+		ORB_SET_STATUS_FIFO_HI(scsi_id->status_fifo_addr, hi->host->node_id);
+	scsi_id->login_orb->status_fifo_lo =
+		ORB_SET_STATUS_FIFO_LO(scsi_id->status_fifo_addr);
 
 	/*
 	 * Byte swap ORB if necessary
@@ -1301,10 +1315,10 @@ static int sbp2_logout_device(struct scsi_id_instance_data *scsi_id)
 	scsi_id->logout_orb->login_ID_misc |= ORB_SET_NOTIFY(1);
 
 	scsi_id->logout_orb->reserved5 = 0x0;
-	scsi_id->logout_orb->status_FIFO_lo = SBP2_STATUS_FIFO_ADDRESS_LO +
-					      SBP2_STATUS_FIFO_ENTRY_TO_OFFSET(scsi_id->ud->id);
-	scsi_id->logout_orb->status_FIFO_hi = (ORB_SET_NODE_ID(hi->host->node_id) |
-					       SBP2_STATUS_FIFO_ADDRESS_HI);
+	scsi_id->logout_orb->status_fifo_hi =
+		ORB_SET_STATUS_FIFO_HI(scsi_id->status_fifo_addr, hi->host->node_id);
+	scsi_id->logout_orb->status_fifo_lo =
+		ORB_SET_STATUS_FIFO_LO(scsi_id->status_fifo_addr);
 
 	/*
 	 * Byte swap ORB if necessary
@@ -1366,10 +1380,10 @@ static int sbp2_reconnect_device(struct scsi_id_instance_data *scsi_id)
 	scsi_id->reconnect_orb->login_ID_misc |= ORB_SET_NOTIFY(1);
 
 	scsi_id->reconnect_orb->reserved5 = 0x0;
-	scsi_id->reconnect_orb->status_FIFO_lo = SBP2_STATUS_FIFO_ADDRESS_LO +
-						 SBP2_STATUS_FIFO_ENTRY_TO_OFFSET(scsi_id->ud->id);
-	scsi_id->reconnect_orb->status_FIFO_hi =
-		(ORB_SET_NODE_ID(hi->host->node_id) | SBP2_STATUS_FIFO_ADDRESS_HI);
+	scsi_id->reconnect_orb->status_fifo_hi =
+		ORB_SET_STATUS_FIFO_HI(scsi_id->status_fifo_addr, hi->host->node_id);
+	scsi_id->reconnect_orb->status_fifo_lo =
+		ORB_SET_STATUS_FIFO_LO(scsi_id->status_fifo_addr);
 
 	/*
 	 * Byte swap ORB if necessary
@@ -1560,7 +1574,7 @@ static void sbp2_parse_unit_directory(struct scsi_id_instance_data *scsi_id,
 	/* Check for a blacklisted set of devices that require us to force
 	 * a 36 byte host inquiry. This can be overriden as a module param
 	 * (to force all hosts).  */
-	for (i = 0; i < NUM_BROKEN_INQUIRY_DEVS; i++) {
+	for (i = 0; i < ARRAY_SIZE(sbp2_broken_inquiry_list); i++) {
 		if ((firmware_revision & 0xffff00) ==
 				sbp2_broken_inquiry_list[i]) {
 			SBP2_WARN("Node " NODE_BUS_FMT ": Using 36byte inquiry workaround",
@@ -2007,18 +2021,6 @@ static int sbp2_send_command(struct scsi_id_instance_data *scsi_id,
 	}
 
 	/*
-	 * The scsi stack sends down a request_bufflen which does not match the
-	 * length field in the scsi cdb. This causes some sbp2 devices to
-	 * reject this inquiry command. Fix the request_bufflen.
-	 */
-	if (*cmd == INQUIRY) {
-		if (force_inquiry_hack || scsi_id->workarounds & SBP2_BREAKAGE_INQUIRY_HACK)
-			request_bufflen = cmd[4] = 0x24;
-		else
-			request_bufflen = cmd[4];
-	}
-
-	/*
 	 * Now actually fill in the comamnd orb and sbp2 s/g list
 	 */
 	sbp2_create_command_orb(scsi_id, command, cmd, SCpnt->use_sg,
@@ -2082,9 +2084,7 @@ static void sbp2_check_sbp2_response(struct scsi_id_instance_data *scsi_id,
 
 	SBP2_DEBUG("sbp2_check_sbp2_response");
 
-	switch (SCpnt->cmnd[0]) {
-
-	case INQUIRY:
+	if (SCpnt->cmnd[0] == INQUIRY && (SCpnt->cmnd[1] & 3) == 0) {
 		/*
 		 * Make sure data length is ok. Minimum length is 36 bytes
 		 */
@@ -2097,13 +2097,7 @@ static void sbp2_check_sbp2_response(struct scsi_id_instance_data *scsi_id,
 		 */
 		scsi_buf[2] |= 2;
 		scsi_buf[3] = (scsi_buf[3] & 0xf0) | 2;
-
-		break;
-
-	default:
-		break;
 	}
-	return;
 }
 
 /*
@@ -2114,7 +2108,6 @@ static int sbp2_handle_status_write(struct hpsb_host *host, int nodeid, int dest
 {
 	struct sbp2scsi_host_info *hi;
 	struct scsi_id_instance_data *scsi_id = NULL, *scsi_id_tmp;
-	u32 id;
 	struct scsi_cmnd *SCpnt = NULL;
 	u32 scsi_status = SBP2_SCSI_STATUS_GOOD;
 	struct sbp2_command_info *command;
@@ -2137,12 +2130,12 @@ static int sbp2_handle_status_write(struct hpsb_host *host, int nodeid, int dest
 	}
 
 	/*
-	 * Find our scsi_id structure by looking at the status fifo address written to by
-	 * the sbp2 device.
+	 * Find our scsi_id structure by looking at the status fifo address
+	 * written to by the sbp2 device.
 	 */
-	id = SBP2_STATUS_FIFO_OFFSET_TO_ENTRY((u32)(addr - SBP2_STATUS_FIFO_ADDRESS));
 	list_for_each_entry(scsi_id_tmp, &hi->scsi_ids, scsi_list) {
-		if (scsi_id_tmp->ne->nodeid == nodeid && scsi_id_tmp->ud->id == id) {
+		if (scsi_id_tmp->ne->nodeid == nodeid &&
+		    scsi_id_tmp->status_fifo_addr == addr) {
 			scsi_id = scsi_id_tmp;
 			break;
 		}
@@ -2483,7 +2476,16 @@ static void sbp2scsi_complete_command(struct scsi_id_instance_data *scsi_id,
 
 static int sbp2scsi_slave_alloc(struct scsi_device *sdev)
 {
-	((struct scsi_id_instance_data *)sdev->host->hostdata[0])->sdev = sdev;
+	struct scsi_id_instance_data *scsi_id =
+		(struct scsi_id_instance_data *)sdev->host->hostdata[0];
+
+	scsi_id->sdev = sdev;
+
+	if (force_inquiry_hack ||
+	    scsi_id->workarounds & SBP2_BREAKAGE_INQUIRY_HACK) {
+		sdev->inquiry_len = 36;
+		sdev->skip_ms_page_8 = 1;
+	}
 	return 0;
 }
 
diff --git a/drivers/ieee1394/sbp2.h b/drivers/ieee1394/sbp2.h
index 900ea1d25e7..e2d357a9ea3 100644
--- a/drivers/ieee1394/sbp2.h
+++ b/drivers/ieee1394/sbp2.h
@@ -33,15 +33,17 @@
 #define ORB_DIRECTION_NO_DATA_TRANSFER  0x2
 
 #define ORB_SET_NULL_PTR(value)			((value & 0x1) << 31)
-#define ORB_SET_NOTIFY(value)                   ((value & 0x1) << 31)
-#define ORB_SET_RQ_FMT(value)                   ((value & 0x3) << 29)	/* unused ? */
+#define ORB_SET_NOTIFY(value)			((value & 0x1) << 31)
+#define ORB_SET_RQ_FMT(value)			((value & 0x3) << 29)	/* unused ? */
 #define ORB_SET_NODE_ID(value)			((value & 0xffff) << 16)
-#define ORB_SET_DATA_SIZE(value)                (value & 0xffff)
-#define ORB_SET_PAGE_SIZE(value)                ((value & 0x7) << 16)
-#define ORB_SET_PAGE_TABLE_PRESENT(value)       ((value & 0x1) << 19)
-#define ORB_SET_MAX_PAYLOAD(value)              ((value & 0xf) << 20)
-#define ORB_SET_SPEED(value)                    ((value & 0x7) << 24)
-#define ORB_SET_DIRECTION(value)                ((value & 0x1) << 27)
+#define ORB_SET_STATUS_FIFO_HI(value, id)	(value >> 32 | ORB_SET_NODE_ID(id))
+#define ORB_SET_STATUS_FIFO_LO(value)		(value & 0xffffffff)
+#define ORB_SET_DATA_SIZE(value)		(value & 0xffff)
+#define ORB_SET_PAGE_SIZE(value)		((value & 0x7) << 16)
+#define ORB_SET_PAGE_TABLE_PRESENT(value)	((value & 0x1) << 19)
+#define ORB_SET_MAX_PAYLOAD(value)		((value & 0xf) << 20)
+#define ORB_SET_SPEED(value)			((value & 0x7) << 24)
+#define ORB_SET_DIRECTION(value)		((value & 0x1) << 27)
 
 struct sbp2_command_orb {
 	volatile u32 next_ORB_hi;
@@ -76,8 +78,8 @@ struct sbp2_login_orb {
 	u32 login_response_lo;
 	u32 lun_misc;
 	u32 passwd_resp_lengths;
-	u32 status_FIFO_hi;
-	u32 status_FIFO_lo;
+	u32 status_fifo_hi;
+	u32 status_fifo_lo;
 };
 
 #define RESPONSE_GET_LOGIN_ID(value)            (value & 0xffff)
@@ -102,8 +104,8 @@ struct sbp2_query_logins_orb {
 	u32 query_response_lo;
 	u32 lun_misc;
 	u32 reserved_resp_length;
-	u32 status_FIFO_hi;
-	u32 status_FIFO_lo;
+	u32 status_fifo_hi;
+	u32 status_fifo_lo;
 };
 
 #define RESPONSE_GET_MAX_LOGINS(value)          (value & 0xffff)
@@ -123,8 +125,8 @@ struct sbp2_reconnect_orb {
 	u32 reserved4;
 	u32 login_ID_misc;
 	u32 reserved5;
-	u32 status_FIFO_hi;
-	u32 status_FIFO_lo;
+	u32 status_fifo_hi;
+	u32 status_fifo_lo;
 };
 
 struct sbp2_logout_orb {
@@ -134,8 +136,8 @@ struct sbp2_logout_orb {
 	u32 reserved4;
 	u32 login_ID_misc;
 	u32 reserved5;
-	u32 status_FIFO_hi;
-	u32 status_FIFO_lo;
+	u32 status_fifo_hi;
+	u32 status_fifo_lo;
 };
 
 #define PAGE_TABLE_SET_SEGMENT_BASE_HI(value)   (value & 0xffff)
@@ -195,30 +197,6 @@ struct sbp2_status_block {
  * Miscellaneous SBP2 related config rom defines
  */
 
-/* The status fifo address definition below is used as a base for each
- * node, which a chunk seperately assigned to each unit directory in the
- * node.  For example, 0xfffe00000000ULL is used for the first sbp2 device
- * detected on node 0, 0xfffe00000020ULL for the next sbp2 device on node
- * 0, and so on.
- *
- * Note: We could use a single status fifo address for all sbp2 devices,
- * and figure out which sbp2 device the status belongs to by looking at
- * the source node id of the status write... but, using separate addresses
- * for each sbp2 unit directory allows for better code and the ability to
- * support multiple luns within a single 1394 node.
- *
- * Also note that we choose the address range below as it is a region
- * specified for write posting, where the ohci controller will
- * automatically send an ack_complete when the status is written by the
- * sbp2 device... saving a split transaction.   =)
- */
-#define SBP2_STATUS_FIFO_ADDRESS				0xfffe00000000ULL
-#define SBP2_STATUS_FIFO_ADDRESS_HI                             0xfffe
-#define SBP2_STATUS_FIFO_ADDRESS_LO                             0x0
-
-#define SBP2_STATUS_FIFO_ENTRY_TO_OFFSET(entry)			((entry) << 5)
-#define SBP2_STATUS_FIFO_OFFSET_TO_ENTRY(offset)		((offset) >> 5)
-
 #define SBP2_UNIT_DIRECTORY_OFFSET_KEY				0xd1
 #define SBP2_CSR_OFFSET_KEY					0x54
 #define SBP2_UNIT_SPEC_ID_KEY					0x12
@@ -258,7 +236,6 @@ struct sbp2_status_block {
  */
 
 #define SBP2_MAX_SG_ELEMENT_LENGTH	0xf000
-#define SBP2_MAX_UDS_PER_NODE		16	/* Maximum scsi devices per node */
 #define SBP2_MAX_SECTORS		255	/* Max sectors supported */
 #define SBP2_MAX_CMDS			8	/* This should be safe */
 
@@ -338,6 +315,11 @@ struct scsi_id_instance_data {
 	u32 sbp2_firmware_revision;
 
 	/*
+	 * Address for the device to write status blocks to
+	 */
+	u64 status_fifo_addr;
+
+	/*
 	 * Variable used for logins, reconnects, logouts, query logins
 	 */
 	atomic_t sbp2_login_complete;
diff --git a/drivers/macintosh/windfarm_smu_sat.c b/drivers/macintosh/windfarm_smu_sat.c
index 3a32c59494f..24e51d5e97f 100644
--- a/drivers/macintosh/windfarm_smu_sat.c
+++ b/drivers/macintosh/windfarm_smu_sat.c
@@ -151,6 +151,7 @@ struct smu_sdbp_header *smu_sat_get_sdb_partition(unsigned int sat_id, int id,
 	kfree(buf);
 	return NULL;
 }
+EXPORT_SYMBOL_GPL(smu_sat_get_sdb_partition);
 
 /* refresh the cache */
 static int wf_sat_read_cache(struct wf_sat *sat)
diff --git a/drivers/md/dm.c b/drivers/md/dm.c
index e9adeb9d172..745ca1f67b1 100644
--- a/drivers/md/dm.c
+++ b/drivers/md/dm.c
@@ -849,10 +849,16 @@ static struct mapped_device *alloc_dev(unsigned int minor, int persistent)
 
 static void free_dev(struct mapped_device *md)
 {
-	free_minor(md->disk->first_minor);
+	unsigned int minor = md->disk->first_minor;
+
+	if (md->suspended_bdev) {
+		thaw_bdev(md->suspended_bdev, NULL);
+		bdput(md->suspended_bdev);
+	}
 	mempool_destroy(md->tio_pool);
 	mempool_destroy(md->io_pool);
 	del_gendisk(md->disk);
+	free_minor(minor);
 	put_disk(md->disk);
 	blk_put_queue(md->queue);
 	kfree(md);
diff --git a/drivers/mmc/mmci.c b/drivers/mmc/mmci.c
index 37ee7f8dc82..9fef29d978b 100644
--- a/drivers/mmc/mmci.c
+++ b/drivers/mmc/mmci.c
@@ -97,6 +97,13 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
 	if (data->flags & MMC_DATA_READ) {
 		datactrl |= MCI_DPSM_DIRECTION;
 		irqmask = MCI_RXFIFOHALFFULLMASK;
+
+		/*
+		 * If we have less than a FIFOSIZE of bytes to transfer,
+		 * trigger a PIO interrupt as soon as any data is available.
+		 */
+		if (host->size < MCI_FIFOSIZE)
+			irqmask |= MCI_RXDATAAVLBLMASK;
 	} else {
 		/*
 		 * We don't actually need to include "FIFO empty" here
diff --git a/drivers/mtd/chips/cfi_cmdset_0001.c b/drivers/mtd/chips/cfi_cmdset_0001.c
index 69c04945591..1c074d63ff3 100644
--- a/drivers/mtd/chips/cfi_cmdset_0001.c
+++ b/drivers/mtd/chips/cfi_cmdset_0001.c
@@ -408,6 +408,7 @@ struct mtd_info *cfi_cmdset_0001(struct map_info *map, int primary)
 		cfi->chips[i].buffer_write_time = 1<<cfi->cfiq->BufWriteTimeoutTyp;
 		cfi->chips[i].erase_time = 1<<cfi->cfiq->BlockEraseTimeoutTyp;
 		cfi->chips[i].ref_point_counter = 0;
+		init_waitqueue_head(&(cfi->chips[i].wq));
 	}
 
 	map->fldrv = &cfi_intelext_chipdrv;
@@ -1019,8 +1020,8 @@ static void __xipram xip_udelay(struct map_info *map, struct flchip *chip,
 #define XIP_INVAL_CACHED_RANGE(map, from, size)  \
 	INVALIDATE_CACHED_RANGE(map, from, size)
 
-#define INVALIDATE_CACHE_UDELAY(map, chip, adr, len, usec)  \
-	UDELAY(map, chip, adr, usec)
+#define INVALIDATE_CACHE_UDELAY(map, chip, cmd_adr, adr, len, usec)  \
+	UDELAY(map, chip, cmd_adr, usec)
 
 /*
  * Extra notes:
@@ -1052,7 +1053,7 @@ do {  \
 	spin_lock(chip->mutex);  \
 } while (0)
 
-#define INVALIDATE_CACHE_UDELAY(map, chip, adr, len, usec)  \
+#define INVALIDATE_CACHE_UDELAY(map, chip, cmd_adr, adr, len, usec)  \
 do {  \
 	spin_unlock(chip->mutex);  \
 	INVALIDATE_CACHED_RANGE(map, adr, len);  \
@@ -1284,7 +1285,7 @@ static int __xipram do_write_oneword(struct map_info *map, struct flchip *chip,
 	map_write(map, datum, adr);
 	chip->state = mode;
 
-	INVALIDATE_CACHE_UDELAY(map, chip,
+	INVALIDATE_CACHE_UDELAY(map, chip, adr,
 				adr, map_bankwidth(map),
 				chip->word_write_time);
 
@@ -1572,8 +1573,8 @@ static int __xipram do_write_buffer(struct map_info *map, struct flchip *chip,
 	map_write(map, CMD(0xd0), cmd_adr);
 	chip->state = FL_WRITING;
 
-	INVALIDATE_CACHE_UDELAY(map, chip,
-				cmd_adr, len,
+	INVALIDATE_CACHE_UDELAY(map, chip, cmd_adr,
+				adr, len,
 				chip->buffer_write_time);
 
 	timeo = jiffies + (HZ/2);
@@ -1744,7 +1745,7 @@ static int __xipram do_erase_oneblock(struct map_info *map, struct flchip *chip,
 	chip->state = FL_ERASING;
 	chip->erase_suspended = 0;
 
-	INVALIDATE_CACHE_UDELAY(map, chip,
+	INVALIDATE_CACHE_UDELAY(map, chip, adr,
 				adr, len,
 				chip->erase_time*1000/2);
 
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 2610cedd55c..840bfed312f 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2020,8 +2020,8 @@ config SIS190
 	  will be called sis190.  This is recommended.
 
 config SKGE
-	tristate "New SysKonnect GigaEthernet support (EXPERIMENTAL)"
-	depends on PCI && EXPERIMENTAL
+	tristate "New SysKonnect GigaEthernet support"
+	depends on PCI
 	select CRC32
 	---help---
 	  This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
@@ -2082,7 +2082,6 @@ config SK98LIN
 	    - Allied Telesyn AT-2971SX Gigabit Ethernet Adapter
 	    - Allied Telesyn AT-2971T Gigabit Ethernet Adapter
 	    - Belkin Gigabit Desktop Card 10/100/1000Base-T Adapter, Copper RJ-45
-	    - DGE-530T Gigabit Ethernet Adapter
 	    - EG1032 v2 Instant Gigabit Network Adapter
 	    - EG1064 v2 Instant Gigabit Network Adapter
 	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Abit)
diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
index e0f51afec77..bcf9f17daf0 100644
--- a/drivers/net/bonding/bond_main.c
+++ b/drivers/net/bonding/bond_main.c
@@ -1581,6 +1581,7 @@ int bond_release(struct net_device *bond_dev, struct net_device *slave_dev)
 		printk(KERN_INFO DRV_NAME
 		       ": %s: %s not enslaved\n",
 		       bond_dev->name, slave_dev->name);
+		write_unlock_bh(&bond->lock);
 		return -EINVAL;
 	}
 
diff --git a/drivers/net/ifb.c b/drivers/net/ifb.c
index 1b699259b4e..31fb2d75dc4 100644
--- a/drivers/net/ifb.c
+++ b/drivers/net/ifb.c
@@ -57,7 +57,7 @@ struct ifb_private {
 	struct sk_buff_head     tq;
 };
 
-static int numifbs = 1;
+static int numifbs = 2;
 
 static void ri_tasklet(unsigned long dev);
 static int ifb_xmit(struct sk_buff *skb, struct net_device *dev);
diff --git a/drivers/net/irda/irda-usb.c b/drivers/net/irda/irda-usb.c
index fa176ffb4ad..8936058a3cc 100644
--- a/drivers/net/irda/irda-usb.c
+++ b/drivers/net/irda/irda-usb.c
@@ -108,6 +108,7 @@ static void irda_usb_close(struct irda_usb_cb *self);
 static void speed_bulk_callback(struct urb *urb, struct pt_regs *regs);
 static void write_bulk_callback(struct urb *urb, struct pt_regs *regs);
 static void irda_usb_receive(struct urb *urb, struct pt_regs *regs);
+static void irda_usb_rx_defer_expired(unsigned long data);
 static int irda_usb_net_open(struct net_device *dev);
 static int irda_usb_net_close(struct net_device *dev);
 static int irda_usb_net_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
@@ -677,6 +678,12 @@ static void irda_usb_net_timeout(struct net_device *netdev)
  * on the interrupt pipe and hang the Rx URB only when an interrupt is
  * received.
  * Jean II
+ *
+ * Note : don't read the above as what we are currently doing, but as
+ * something we could do with KC dongle. Also don't forget that the
+ * interrupt pipe is not part of the original standard, so this would
+ * need to be optional...
+ * Jean II
  */
 
 /*------------------------------------------------------------------*/
@@ -704,10 +711,8 @@ static void irda_usb_submit(struct irda_usb_cb *self, struct sk_buff *skb, struc
 	/* Reinitialize URB */
 	usb_fill_bulk_urb(urb, self->usbdev, 
 		      usb_rcvbulkpipe(self->usbdev, self->bulk_in_ep), 
-		      skb->data, skb->truesize,
+		      skb->data, IRDA_SKB_MAX_MTU,
                       irda_usb_receive, skb);
-	/* Note : unlink *must* be synchronous because of the code in 
-	 * irda_usb_net_close() -> free the skb - Jean II */
 	urb->status = 0;
 
 	/* Can be called from irda_usb_receive (irq handler) -> GFP_ATOMIC */
@@ -734,6 +739,7 @@ static void irda_usb_receive(struct urb *urb, struct pt_regs *regs)
 	struct irda_skb_cb *cb;
 	struct sk_buff *newskb;
 	struct sk_buff *dataskb;
+	struct urb *next_urb;
 	int		docopy;
 
 	IRDA_DEBUG(2, "%s(), len=%d\n", __FUNCTION__, urb->actual_length);
@@ -755,20 +761,37 @@ static void irda_usb_receive(struct urb *urb, struct pt_regs *regs)
 	if (urb->status != 0) {
 		switch (urb->status) {
 		case -EILSEQ:
-			self->stats.rx_errors++;
 			self->stats.rx_crc_errors++;	
-			break;
+			/* Also precursor to a hot-unplug on UHCI. */
+			/* Fallthrough... */
 		case -ECONNRESET:		/* -104 */
-			IRDA_DEBUG(0, "%s(), Connection Reset (-104), transfer_flags 0x%04X \n", __FUNCTION__, urb->transfer_flags);
+			/* Random error, if I remember correctly */
 			/* uhci_cleanup_unlink() is going to kill the Rx
 			 * URB just after we return. No problem, at this
 			 * point the URB will be idle ;-) - Jean II */
-			break;
+		case -ESHUTDOWN:		/* -108 */
+			/* That's usually a hot-unplug. Submit will fail... */
+		case -ETIMEDOUT:		/* -110 */
+			/* Usually precursor to a hot-unplug on OHCI. */
 		default:
-			IRDA_DEBUG(0, "%s(), RX status %d,transfer_flags 0x%04X \n", __FUNCTION__, urb->status, urb->transfer_flags);
+			self->stats.rx_errors++;
+			IRDA_DEBUG(0, "%s(), RX status %d, transfer_flags 0x%04X \n", __FUNCTION__, urb->status, urb->transfer_flags);
 			break;
 		}
-		goto done;
+		/* If we received an error, we don't want to resubmit the
+		 * Rx URB straight away but to give the USB layer a little
+		 * bit of breathing room.
+		 * We are in the USB thread context, therefore there is a
+		 * danger of recursion (new URB we submit fails, we come
+		 * back here).
+		 * With recent USB stack (2.6.15+), I'm seeing that on
+		 * hot unplug of the dongle...
+		 * Lowest effective timer is 10ms...
+		 * Jean II */
+		self->rx_defer_timer.function = &irda_usb_rx_defer_expired;
+		self->rx_defer_timer.data = (unsigned long) urb;
+		mod_timer(&self->rx_defer_timer, jiffies + (10 * HZ / 1000));
+		return;
 	}
 	
 	/* Check for empty frames */
@@ -845,13 +868,45 @@ done:
 	 * idle slot....
 	 * Jean II */
 	/* Note : with this scheme, we could submit the idle URB before
-	 * processing the Rx URB. Another time... Jean II */
+	 * processing the Rx URB. I don't think it would buy us anything as
+	 * we are running in the USB thread context. Jean II */
+	next_urb = self->idle_rx_urb;
 
-	/* Submit the idle URB to replace the URB we've just received */
-	irda_usb_submit(self, skb, self->idle_rx_urb);
 	/* Recycle Rx URB : Now, the idle URB is the present one */
 	urb->context = NULL;
 	self->idle_rx_urb = urb;
+
+	/* Submit the idle URB to replace the URB we've just received.
+	 * Do it last to avoid race conditions... Jean II */
+	irda_usb_submit(self, skb, next_urb);
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * In case of errors, we want the USB layer to have time to recover.
+ * Now, it is time to resubmit ouur Rx URB...
+ */
+static void irda_usb_rx_defer_expired(unsigned long data)
+{
+	struct urb *urb = (struct urb *) data;
+	struct sk_buff *skb = (struct sk_buff *) urb->context;
+	struct irda_usb_cb *self; 
+	struct irda_skb_cb *cb;
+	struct urb *next_urb;
+
+	IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+
+	/* Find ourselves */
+	cb = (struct irda_skb_cb *) skb->cb;
+	IRDA_ASSERT(cb != NULL, return;);
+	self = (struct irda_usb_cb *) cb->context;
+	IRDA_ASSERT(self != NULL, return;);
+
+	/* Same stuff as when Rx is done, see above... */
+	next_urb = self->idle_rx_urb;
+	urb->context = NULL;
+	self->idle_rx_urb = urb;
+	irda_usb_submit(self, skb, next_urb);
 }
 
 /*------------------------------------------------------------------*/
@@ -990,6 +1045,9 @@ static int irda_usb_net_close(struct net_device *netdev)
 	/* Stop network Tx queue */
 	netif_stop_queue(netdev);
 
+	/* Kill defered Rx URB */
+	del_timer(&self->rx_defer_timer);
+
 	/* Deallocate all the Rx path buffers (URBs and skb) */
 	for (i = 0; i < IU_MAX_RX_URBS; i++) {
 		struct urb *urb = self->rx_urb[i];
@@ -1365,6 +1423,7 @@ static int irda_usb_probe(struct usb_interface *intf,
 	self = net->priv;
 	self->netdev = net;
 	spin_lock_init(&self->lock);
+	init_timer(&self->rx_defer_timer);
 
 	/* Create all of the needed urbs */
 	for (i = 0; i < IU_MAX_RX_URBS; i++) {
@@ -1498,6 +1557,9 @@ static void irda_usb_disconnect(struct usb_interface *intf)
 	 * This will stop/desactivate the Tx path. - Jean II */
 	self->present = 0;
 
+	/* Kill defered Rx URB */
+	del_timer(&self->rx_defer_timer);
+
 	/* We need to have irq enabled to unlink the URBs. That's OK,
 	 * at this point the Tx path is gone - Jean II */
 	spin_unlock_irqrestore(&self->lock, flags);
@@ -1507,11 +1569,11 @@ static void irda_usb_disconnect(struct usb_interface *intf)
 		/* Accept no more transmissions */
 		/*netif_device_detach(self->netdev);*/
 		netif_stop_queue(self->netdev);
-		/* Stop all the receive URBs */
+		/* Stop all the receive URBs. Must be synchronous. */
 		for (i = 0; i < IU_MAX_RX_URBS; i++)
 			usb_kill_urb(self->rx_urb[i]);
 		/* Cancel Tx and speed URB.
-		 * Toggle flags to make sure it's synchronous. */
+		 * Make sure it's synchronous to avoid races. */
 		usb_kill_urb(self->tx_urb);
 		usb_kill_urb(self->speed_urb);
 	}
diff --git a/drivers/net/irda/irda-usb.h b/drivers/net/irda/irda-usb.h
index bd8f6654232..4026af42dd4 100644
--- a/drivers/net/irda/irda-usb.h
+++ b/drivers/net/irda/irda-usb.h
@@ -136,8 +136,6 @@ struct irda_usb_cb {
 	__u16 bulk_out_mtu;		/* Max Tx packet size in bytes */
 	__u8  bulk_int_ep;		/* Interrupt Endpoint assignments */
 
-	wait_queue_head_t wait_q;	/* for timeouts */
-
 	struct urb *rx_urb[IU_MAX_RX_URBS];	/* URBs used to receive data frames */
 	struct urb *idle_rx_urb;	/* Pointer to idle URB in Rx path */
 	struct urb *tx_urb;		/* URB used to send data frames */
@@ -147,17 +145,18 @@ struct irda_usb_cb {
 	struct net_device_stats stats;
 	struct irlap_cb   *irlap;	/* The link layer we are binded to */
 	struct qos_info qos;
-	hashbin_t *tx_list;		/* Queued transmit skb's */
 	char *speed_buff;		/* Buffer for speed changes */
 
 	struct timeval stamp;
 	struct timeval now;
 
-	spinlock_t lock;		/* For serializing operations */
+	spinlock_t lock;		/* For serializing Tx operations */
 
 	__u16 xbofs;			/* Current xbofs setting */
 	__s16 new_xbofs;		/* xbofs we need to set */
 	__u32 speed;			/* Current speed */
 	__s32 new_speed;		/* speed we need to set */
+
+	struct timer_list rx_defer_timer;	/* Wait for Rx error to clear */
 };
 
diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c
index 6e1018448ee..8cc0d0bbdf5 100644
--- a/drivers/net/r8169.c
+++ b/drivers/net/r8169.c
@@ -287,6 +287,20 @@ enum RTL8169_register_content {
 	TxInterFrameGapShift = 24,
 	TxDMAShift = 8,	/* DMA burst value (0-7) is shift this many bits */
 
+	/* Config1 register p.24 */
+	PMEnable	= (1 << 0),	/* Power Management Enable */
+
+	/* Config3 register p.25 */
+	MagicPacket	= (1 << 5),	/* Wake up when receives a Magic Packet */
+	LinkUp		= (1 << 4),	/* Wake up when the cable connection is re-established */
+
+	/* Config5 register p.27 */
+	BWF		= (1 << 6),	/* Accept Broadcast wakeup frame */
+	MWF		= (1 << 5),	/* Accept Multicast wakeup frame */
+	UWF		= (1 << 4),	/* Accept Unicast wakeup frame */
+	LanWake		= (1 << 1),	/* LanWake enable/disable */
+	PMEStatus	= (1 << 0),	/* PME status can be reset by PCI RST# */
+
 	/* TBICSR p.28 */
 	TBIReset	= 0x80000000,
 	TBILoopback	= 0x40000000,
@@ -433,6 +447,7 @@ struct rtl8169_private {
 	unsigned int (*phy_reset_pending)(void __iomem *);
 	unsigned int (*link_ok)(void __iomem *);
 	struct work_struct task;
+	unsigned wol_enabled : 1;
 };
 
 MODULE_AUTHOR("Realtek and the Linux r8169 crew <netdev@vger.kernel.org>");
@@ -607,6 +622,80 @@ static void rtl8169_link_option(int idx, u8 *autoneg, u16 *speed, u8 *duplex)
 	*duplex = p->duplex;
 }
 
+static void rtl8169_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+	struct rtl8169_private *tp = netdev_priv(dev);
+	void __iomem *ioaddr = tp->mmio_addr;
+	u8 options;
+
+	wol->wolopts = 0;
+
+#define WAKE_ANY (WAKE_PHY | WAKE_MAGIC | WAKE_UCAST | WAKE_BCAST | WAKE_MCAST)
+	wol->supported = WAKE_ANY;
+
+	spin_lock_irq(&tp->lock);
+
+	options = RTL_R8(Config1);
+	if (!(options & PMEnable))
+		goto out_unlock;
+
+	options = RTL_R8(Config3);
+	if (options & LinkUp)
+		wol->wolopts |= WAKE_PHY;
+	if (options & MagicPacket)
+		wol->wolopts |= WAKE_MAGIC;
+
+	options = RTL_R8(Config5);
+	if (options & UWF)
+		wol->wolopts |= WAKE_UCAST;
+	if (options & BWF)
+	        wol->wolopts |= WAKE_BCAST;
+	if (options & MWF)
+	        wol->wolopts |= WAKE_MCAST;
+
+out_unlock:
+	spin_unlock_irq(&tp->lock);
+}
+
+static int rtl8169_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+	struct rtl8169_private *tp = netdev_priv(dev);
+	void __iomem *ioaddr = tp->mmio_addr;
+	int i;
+	static struct {
+		u32 opt;
+		u16 reg;
+		u8  mask;
+	} cfg[] = {
+		{ WAKE_ANY,   Config1, PMEnable },
+		{ WAKE_PHY,   Config3, LinkUp },
+		{ WAKE_MAGIC, Config3, MagicPacket },
+		{ WAKE_UCAST, Config5, UWF },
+		{ WAKE_BCAST, Config5, BWF },
+		{ WAKE_MCAST, Config5, MWF },
+		{ WAKE_ANY,   Config5, LanWake }
+	};
+
+	spin_lock_irq(&tp->lock);
+
+	RTL_W8(Cfg9346, Cfg9346_Unlock);
+
+	for (i = 0; i < ARRAY_SIZE(cfg); i++) {
+		u8 options = RTL_R8(cfg[i].reg) & ~cfg[i].mask;
+		if (wol->wolopts & cfg[i].opt)
+			options |= cfg[i].mask;
+		RTL_W8(cfg[i].reg, options);
+	}
+
+	RTL_W8(Cfg9346, Cfg9346_Lock);
+
+	tp->wol_enabled = (wol->wolopts) ? 1 : 0;
+
+	spin_unlock_irq(&tp->lock);
+
+	return 0;
+}
+
 static void rtl8169_get_drvinfo(struct net_device *dev,
 				struct ethtool_drvinfo *info)
 {
@@ -1025,6 +1114,8 @@ static struct ethtool_ops rtl8169_ethtool_ops = {
 	.get_tso		= ethtool_op_get_tso,
 	.set_tso		= ethtool_op_set_tso,
 	.get_regs		= rtl8169_get_regs,
+	.get_wol		= rtl8169_get_wol,
+	.set_wol		= rtl8169_set_wol,
 	.get_strings		= rtl8169_get_strings,
 	.get_stats_count	= rtl8169_get_stats_count,
 	.get_ethtool_stats	= rtl8169_get_ethtool_stats,
@@ -1442,6 +1533,11 @@ rtl8169_init_board(struct pci_dev *pdev, struct net_device **dev_out,
 	}
 	tp->chipset = i;
 
+	RTL_W8(Cfg9346, Cfg9346_Unlock);
+	RTL_W8(Config1, RTL_R8(Config1) | PMEnable);
+	RTL_W8(Config5, RTL_R8(Config5) & PMEStatus);
+	RTL_W8(Cfg9346, Cfg9346_Lock);
+
 	*ioaddr_out = ioaddr;
 	*dev_out = dev;
 out:
@@ -1612,49 +1708,6 @@ rtl8169_remove_one(struct pci_dev *pdev)
 	pci_set_drvdata(pdev, NULL);
 }
 
-#ifdef CONFIG_PM
-
-static int rtl8169_suspend(struct pci_dev *pdev, pm_message_t state)
-{
-	struct net_device *dev = pci_get_drvdata(pdev);
-	struct rtl8169_private *tp = netdev_priv(dev);
-	void __iomem *ioaddr = tp->mmio_addr;
-	unsigned long flags;
-
-	if (!netif_running(dev))
-		return 0;
-	
-	netif_device_detach(dev);
-	netif_stop_queue(dev);
-	spin_lock_irqsave(&tp->lock, flags);
-
-	/* Disable interrupts, stop Rx and Tx */
-	RTL_W16(IntrMask, 0);
-	RTL_W8(ChipCmd, 0);
-		
-	/* Update the error counts. */
-	tp->stats.rx_missed_errors += RTL_R32(RxMissed);
-	RTL_W32(RxMissed, 0);
-	spin_unlock_irqrestore(&tp->lock, flags);
-	
-	return 0;
-}
-
-static int rtl8169_resume(struct pci_dev *pdev)
-{
-	struct net_device *dev = pci_get_drvdata(pdev);
-
-	if (!netif_running(dev))
-	    return 0;
-
-	netif_device_attach(dev);
-	rtl8169_hw_start(dev);
-
-	return 0;
-}
-                                                                                
-#endif /* CONFIG_PM */
-
 static void rtl8169_set_rxbufsize(struct rtl8169_private *tp,
 				  struct net_device *dev)
 {
@@ -2700,6 +2753,56 @@ static struct net_device_stats *rtl8169_get_stats(struct net_device *dev)
 	return &tp->stats;
 }
 
+#ifdef CONFIG_PM
+
+static int rtl8169_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+	struct net_device *dev = pci_get_drvdata(pdev);
+	struct rtl8169_private *tp = netdev_priv(dev);
+	void __iomem *ioaddr = tp->mmio_addr;
+
+	if (!netif_running(dev))
+		goto out;
+
+	netif_device_detach(dev);
+	netif_stop_queue(dev);
+
+	spin_lock_irq(&tp->lock);
+
+	rtl8169_asic_down(ioaddr);
+
+	tp->stats.rx_missed_errors += RTL_R32(RxMissed);
+	RTL_W32(RxMissed, 0);
+
+	spin_unlock_irq(&tp->lock);
+
+	pci_save_state(pdev);
+	pci_enable_wake(pdev, pci_choose_state(pdev, state), tp->wol_enabled);
+	pci_set_power_state(pdev, pci_choose_state(pdev, state));
+out:
+	return 0;
+}
+
+static int rtl8169_resume(struct pci_dev *pdev)
+{
+	struct net_device *dev = pci_get_drvdata(pdev);
+
+	if (!netif_running(dev))
+		goto out;
+
+	netif_device_attach(dev);
+
+	pci_set_power_state(pdev, PCI_D0);
+	pci_restore_state(pdev);
+	pci_enable_wake(pdev, PCI_D0, 0);
+
+	rtl8169_schedule_work(dev, rtl8169_reset_task);
+out:
+	return 0;
+}
+
+#endif /* CONFIG_PM */
+
 static struct pci_driver rtl8169_pci_driver = {
 	.name		= MODULENAME,
 	.id_table	= rtl8169_pci_tbl,
diff --git a/drivers/net/sis190.c b/drivers/net/sis190.c
index b420182eec4..ed4bc91638d 100644
--- a/drivers/net/sis190.c
+++ b/drivers/net/sis190.c
@@ -1791,6 +1791,8 @@ static int __devinit sis190_init_one(struct pci_dev *pdev,
 		goto out;
 	}
 
+	pci_set_drvdata(pdev, dev);
+
 	tp = netdev_priv(dev);
 	ioaddr = tp->mmio_addr;
 
@@ -1827,8 +1829,6 @@ static int __devinit sis190_init_one(struct pci_dev *pdev,
 	if (rc < 0)
 		goto err_remove_mii;
 
-	pci_set_drvdata(pdev, dev);
-
 	net_probe(tp, KERN_INFO "%s: %s at %p (IRQ: %d), "
 	       "%2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2x\n",
 	       pci_name(pdev), sis_chip_info[ent->driver_data].name,
diff --git a/drivers/net/sis900.c b/drivers/net/sis900.c
index 3d95fa20cd8..7a952fe60be 100644
--- a/drivers/net/sis900.c
+++ b/drivers/net/sis900.c
@@ -540,7 +540,7 @@ static int __devinit sis900_probe(struct pci_dev *pci_dev,
 	printk("%2.2x.\n", net_dev->dev_addr[i]);
 
 	/* Detect Wake on Lan support */
-	ret = inl(CFGPMC & PMESP);
+	ret = (inl(net_dev->base_addr + CFGPMC) & PMESP) >> 27;
 	if (netif_msg_probe(sis_priv) && (ret & PME_D3C) == 0)
 		printk(KERN_INFO "%s: Wake on LAN only available from suspend to RAM.", net_dev->name);
 
@@ -2040,7 +2040,7 @@ static int sis900_set_wol(struct net_device *net_dev, struct ethtool_wolinfo *wo
 
 	if (wol->wolopts == 0) {
 		pci_read_config_dword(sis_priv->pci_dev, CFGPMCSR, &cfgpmcsr);
-		cfgpmcsr |= ~PME_EN;
+		cfgpmcsr &= ~PME_EN;
 		pci_write_config_dword(sis_priv->pci_dev, CFGPMCSR, cfgpmcsr);
 		outl(pmctrl_bits, pmctrl_addr);
 		if (netif_msg_wol(sis_priv))
diff --git a/drivers/net/skge.c b/drivers/net/skge.c
index bf55a4cfb3d..25e028b7ce4 100644
--- a/drivers/net/skge.c
+++ b/drivers/net/skge.c
@@ -879,13 +879,12 @@ static int __xm_phy_read(struct skge_hw *hw, int port, u16 reg, u16 *val)
 	int i;
 
 	xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr);
-	xm_read16(hw, port, XM_PHY_DATA);
+	*val = xm_read16(hw, port, XM_PHY_DATA);
 
-	/* Need to wait for external PHY */
 	for (i = 0; i < PHY_RETRIES; i++) {
-		udelay(1);
 		if (xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_RDY)
 			goto ready;
+		udelay(1);
 	}
 
 	return -ETIMEDOUT;
@@ -918,7 +917,12 @@ static int xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
 
  ready:
 	xm_write16(hw, port, XM_PHY_DATA, val);
-	return 0;
+	for (i = 0; i < PHY_RETRIES; i++) {
+		if (!(xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY))
+			return 0;
+		udelay(1);
+	}
+	return -ETIMEDOUT;
 }
 
 static void genesis_init(struct skge_hw *hw)
@@ -1168,13 +1172,17 @@ static void genesis_mac_init(struct skge_hw *hw, int port)
 	u32 r;
 	const u8 zero[6]  = { 0 };
 
-	/* Clear MIB counters */
-	xm_write16(hw, port, XM_STAT_CMD,
-			XM_SC_CLR_RXC | XM_SC_CLR_TXC);
-	/* Clear two times according to Errata #3 */
-	xm_write16(hw, port, XM_STAT_CMD,
-			XM_SC_CLR_RXC | XM_SC_CLR_TXC);
+	for (i = 0; i < 10; i++) {
+		skge_write16(hw, SK_REG(port, TX_MFF_CTRL1),
+			     MFF_SET_MAC_RST);
+		if (skge_read16(hw, SK_REG(port, TX_MFF_CTRL1)) & MFF_SET_MAC_RST)
+			goto reset_ok;
+		udelay(1);
+	}
 
+	printk(KERN_WARNING PFX "%s: genesis reset failed\n", dev->name);
+
+ reset_ok:
 	/* Unreset the XMAC. */
 	skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_CLR_MAC_RST);
 
@@ -1191,7 +1199,7 @@ static void genesis_mac_init(struct skge_hw *hw, int port)
 		r |= GP_DIR_2|GP_IO_2;
 
 	skge_write32(hw, B2_GP_IO, r);
-	skge_read32(hw, B2_GP_IO);
+
 
 	/* Enable GMII interface */
 	xm_write16(hw, port, XM_HW_CFG, XM_HW_GMII_MD);
@@ -1205,6 +1213,13 @@ static void genesis_mac_init(struct skge_hw *hw, int port)
 	for (i = 1; i < 16; i++)
 		xm_outaddr(hw, port, XM_EXM(i), zero);
 
+	/* Clear MIB counters */
+	xm_write16(hw, port, XM_STAT_CMD,
+			XM_SC_CLR_RXC | XM_SC_CLR_TXC);
+	/* Clear two times according to Errata #3 */
+	xm_write16(hw, port, XM_STAT_CMD,
+			XM_SC_CLR_RXC | XM_SC_CLR_TXC);
+
 	/* configure Rx High Water Mark (XM_RX_HI_WM) */
 	xm_write16(hw, port, XM_RX_HI_WM, 1450);
 
@@ -1697,6 +1712,7 @@ static void yukon_mac_init(struct skge_hw *hw, int port)
 	skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_SET);
 	skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_CLR);
 	skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON | GMC_RST_CLR);
+
 	if (skge->autoneg == AUTONEG_DISABLE) {
 		reg = GM_GPCR_AU_ALL_DIS;
 		gma_write16(hw, port, GM_GP_CTRL,
@@ -1704,16 +1720,23 @@ static void yukon_mac_init(struct skge_hw *hw, int port)
 
 		switch (skge->speed) {
 		case SPEED_1000:
+			reg &= ~GM_GPCR_SPEED_100;
 			reg |= GM_GPCR_SPEED_1000;
-			/* fallthru */
+			break;
 		case SPEED_100:
+			reg &= ~GM_GPCR_SPEED_1000;
 			reg |= GM_GPCR_SPEED_100;
+			break;
+		case SPEED_10:
+			reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
+			break;
 		}
 
 		if (skge->duplex == DUPLEX_FULL)
 			reg |= GM_GPCR_DUP_FULL;
 	} else
 		reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL;
+
 	switch (skge->flow_control) {
 	case FLOW_MODE_NONE:
 		skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
@@ -2162,8 +2185,10 @@ static int skge_up(struct net_device *dev)
 	skge->tx_avail = skge->tx_ring.count - 1;
 
 	/* Enable IRQ from port */
+	spin_lock_irq(&hw->hw_lock);
 	hw->intr_mask |= portirqmask[port];
 	skge_write32(hw, B0_IMSK, hw->intr_mask);
+	spin_unlock_irq(&hw->hw_lock);
 
 	/* Initialize MAC */
 	spin_lock_bh(&hw->phy_lock);
@@ -2221,8 +2246,10 @@ static int skge_down(struct net_device *dev)
 	else
 		yukon_stop(skge);
 
+	spin_lock_irq(&hw->hw_lock);
 	hw->intr_mask &= ~portirqmask[skge->port];
 	skge_write32(hw, B0_IMSK, hw->intr_mask);
+	spin_unlock_irq(&hw->hw_lock);
 
 	/* Stop transmitter */
 	skge_write8(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_STOP);
@@ -2670,8 +2697,7 @@ static int skge_poll(struct net_device *dev, int *budget)
 
 	/* restart receiver */
 	wmb();
-	skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR),
-		    CSR_START | CSR_IRQ_CL_F);
+	skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR), CSR_START);
 
 	*budget -= work_done;
 	dev->quota -= work_done;
@@ -2679,10 +2705,11 @@ static int skge_poll(struct net_device *dev, int *budget)
 	if (work_done >=  to_do)
 		return 1; /* not done */
 
-	netif_rx_complete(dev);
-	hw->intr_mask |= portirqmask[skge->port];
-	skge_write32(hw, B0_IMSK, hw->intr_mask);
-	skge_read32(hw, B0_IMSK);
+	spin_lock_irq(&hw->hw_lock);
+	__netif_rx_complete(dev);
+  	hw->intr_mask |= portirqmask[skge->port];
+  	skge_write32(hw, B0_IMSK, hw->intr_mask);
+ 	spin_unlock_irq(&hw->hw_lock);
 
 	return 0;
 }
@@ -2842,18 +2869,10 @@ static void skge_extirq(unsigned long data)
 	}
 	spin_unlock(&hw->phy_lock);
 
-	local_irq_disable();
+	spin_lock_irq(&hw->hw_lock);
 	hw->intr_mask |= IS_EXT_REG;
 	skge_write32(hw, B0_IMSK, hw->intr_mask);
-	local_irq_enable();
-}
-
-static inline void skge_wakeup(struct net_device *dev)
-{
-	struct skge_port *skge = netdev_priv(dev);
-
-	prefetch(skge->rx_ring.to_clean);
-	netif_rx_schedule(dev);
+	spin_unlock_irq(&hw->hw_lock);
 }
 
 static irqreturn_t skge_intr(int irq, void *dev_id, struct pt_regs *regs)
@@ -2864,15 +2883,17 @@ static irqreturn_t skge_intr(int irq, void *dev_id, struct pt_regs *regs)
 	if (status == 0 || status == ~0) /* hotplug or shared irq */
 		return IRQ_NONE;
 
-	status &= hw->intr_mask;
+	spin_lock(&hw->hw_lock);
 	if (status & IS_R1_F) {
+		skge_write8(hw, Q_ADDR(Q_R1, Q_CSR), CSR_IRQ_CL_F);
 		hw->intr_mask &= ~IS_R1_F;
-		skge_wakeup(hw->dev[0]);
+		netif_rx_schedule(hw->dev[0]);
 	}
 
 	if (status & IS_R2_F) {
+		skge_write8(hw, Q_ADDR(Q_R2, Q_CSR), CSR_IRQ_CL_F);
 		hw->intr_mask &= ~IS_R2_F;
-		skge_wakeup(hw->dev[1]);
+		netif_rx_schedule(hw->dev[1]);
 	}
 
 	if (status & IS_XA1_F)
@@ -2914,6 +2935,7 @@ static irqreturn_t skge_intr(int irq, void *dev_id, struct pt_regs *regs)
 	}
 
 	skge_write32(hw, B0_IMSK, hw->intr_mask);
+	spin_unlock(&hw->hw_lock);
 
 	return IRQ_HANDLED;
 }
@@ -3282,6 +3304,7 @@ static int __devinit skge_probe(struct pci_dev *pdev,
 
 	hw->pdev = pdev;
 	spin_lock_init(&hw->phy_lock);
+	spin_lock_init(&hw->hw_lock);
 	tasklet_init(&hw->ext_tasklet, skge_extirq, (unsigned long) hw);
 
 	hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
diff --git a/drivers/net/skge.h b/drivers/net/skge.h
index 2efdacc290e..941f12a333b 100644
--- a/drivers/net/skge.h
+++ b/drivers/net/skge.h
@@ -2402,6 +2402,7 @@ struct skge_hw {
 
 	struct tasklet_struct ext_tasklet;
 	spinlock_t	     phy_lock;
+	spinlock_t	     hw_lock;
 };
 
 enum {
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index cae2edf2300..ca8160d6822 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -195,11 +195,11 @@ static int sky2_set_power_state(struct sky2_hw *hw, pci_power_t state)
 	pr_debug("sky2_set_power_state %d\n", state);
 	sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
 
-	pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_PMC, &power_control);
+	power_control = sky2_pci_read16(hw, hw->pm_cap + PCI_PM_PMC);
 	vaux = (sky2_read16(hw, B0_CTST) & Y2_VAUX_AVAIL) &&
 		(power_control & PCI_PM_CAP_PME_D3cold);
 
-	pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_CTRL, &power_control);
+	power_control = sky2_pci_read16(hw, hw->pm_cap + PCI_PM_CTRL);
 
 	power_control |= PCI_PM_CTRL_PME_STATUS;
 	power_control &= ~(PCI_PM_CTRL_STATE_MASK);
@@ -223,7 +223,7 @@ static int sky2_set_power_state(struct sky2_hw *hw, pci_power_t state)
 			sky2_write8(hw, B2_Y2_CLK_GATE, 0);
 
 		/* Turn off phy power saving */
-		pci_read_config_dword(hw->pdev, PCI_DEV_REG1, &reg1);
+		reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
 		reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
 
 		/* looks like this XL is back asswards .. */
@@ -232,18 +232,28 @@ static int sky2_set_power_state(struct sky2_hw *hw, pci_power_t state)
 			if (hw->ports > 1)
 				reg1 |= PCI_Y2_PHY2_COMA;
 		}
-		pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
+
+		if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+			sky2_pci_write32(hw, PCI_DEV_REG3, 0);
+			reg1 = sky2_pci_read32(hw, PCI_DEV_REG4);
+			reg1 &= P_ASPM_CONTROL_MSK;
+			sky2_pci_write32(hw, PCI_DEV_REG4, reg1);
+			sky2_pci_write32(hw, PCI_DEV_REG5, 0);
+		}
+
+		sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
+
 		break;
 
 	case PCI_D3hot:
 	case PCI_D3cold:
 		/* Turn on phy power saving */
-		pci_read_config_dword(hw->pdev, PCI_DEV_REG1, &reg1);
+		reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
 		if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
 			reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
 		else
 			reg1 |= (PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
-		pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
+		sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
 
 		if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
 			sky2_write8(hw, B2_Y2_CLK_GATE, 0);
@@ -265,7 +275,7 @@ static int sky2_set_power_state(struct sky2_hw *hw, pci_power_t state)
 		ret = -1;
 	}
 
-	pci_write_config_byte(hw->pdev, hw->pm_cap + PCI_PM_CTRL, power_control);
+	sky2_pci_write16(hw, hw->pm_cap + PCI_PM_CTRL, power_control);
 	sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
 	return ret;
 }
@@ -463,16 +473,31 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
 		ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
 	}
 
-	gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
+	if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
+		/* apply fixes in PHY AFE */
+		gm_phy_write(hw, port, 22, 255);
+		/* increase differential signal amplitude in 10BASE-T */
+		gm_phy_write(hw, port, 24, 0xaa99);
+		gm_phy_write(hw, port, 23, 0x2011);
 
-	if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
-		/* turn on 100 Mbps LED (LED_LINK100) */
-		ledover |= PHY_M_LED_MO_100(MO_LED_ON);
-	}
+		/* fix for IEEE A/B Symmetry failure in 1000BASE-T */
+		gm_phy_write(hw, port, 24, 0xa204);
+		gm_phy_write(hw, port, 23, 0x2002);
 
-	if (ledover)
-		gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
+		/* set page register to 0 */
+		gm_phy_write(hw, port, 22, 0);
+	} else {
+		gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
+
+		if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
+			/* turn on 100 Mbps LED (LED_LINK100) */
+			ledover |= PHY_M_LED_MO_100(MO_LED_ON);
+		}
+
+		if (ledover)
+			gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
 
+	}
 	/* Enable phy interrupt on auto-negotiation complete (or link up) */
 	if (sky2->autoneg == AUTONEG_ENABLE)
 		gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
@@ -520,10 +545,16 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port)
 
 		switch (sky2->speed) {
 		case SPEED_1000:
+			reg &= ~GM_GPCR_SPEED_100;
 			reg |= GM_GPCR_SPEED_1000;
-			/* fallthru */
+			break;
 		case SPEED_100:
+			reg &= ~GM_GPCR_SPEED_1000;
 			reg |= GM_GPCR_SPEED_100;
+			break;
+		case SPEED_10:
+			reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
+			break;
 		}
 
 		if (sky2->duplex == DUPLEX_FULL)
@@ -947,6 +978,12 @@ static int sky2_rx_start(struct sky2_port *sky2)
 
 	sky2->rx_put = sky2->rx_next = 0;
 	sky2_qset(hw, rxq);
+
+	if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
+		/* MAC Rx RAM Read is controlled by hardware */
+		sky2_write32(hw, Q_ADDR(rxq, Q_F), F_M_RX_RAM_DIS);
+	}
+
 	sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
 
 	rx_set_checksum(sky2);
@@ -1029,9 +1066,10 @@ static int sky2_up(struct net_device *dev)
 		    RB_RST_SET);
 
 	sky2_qset(hw, txqaddr[port]);
-	if (hw->chip_id == CHIP_ID_YUKON_EC_U)
-		sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
 
+	/* Set almost empty threshold */
+	if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == 1)
+		sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
 
 	sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
 			   TX_RING_SIZE - 1);
@@ -1041,8 +1079,10 @@ static int sky2_up(struct net_device *dev)
 		goto err_out;
 
 	/* Enable interrupts from phy/mac for port */
+	spin_lock_irq(&hw->hw_lock);
 	hw->intr_mask |= (port == 0) ? Y2_IS_PORT_1 : Y2_IS_PORT_2;
 	sky2_write32(hw, B0_IMSK, hw->intr_mask);
+	spin_unlock_irq(&hw->hw_lock);
 	return 0;
 
 err_out:
@@ -1342,10 +1382,10 @@ static int sky2_down(struct net_device *dev)
 	netif_stop_queue(dev);
 
 	/* Disable port IRQ */
-	local_irq_disable();
+	spin_lock_irq(&hw->hw_lock);
 	hw->intr_mask &= ~((sky2->port == 0) ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2);
 	sky2_write32(hw, B0_IMSK, hw->intr_mask);
-	local_irq_enable();
+	spin_unlock_irq(&hw->hw_lock);
 
 	flush_scheduled_work();
 
@@ -1446,6 +1486,29 @@ static void sky2_link_up(struct sky2_port *sky2)
 	sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
 
 	reg = gma_read16(hw, port, GM_GP_CTRL);
+	if (sky2->autoneg == AUTONEG_DISABLE) {
+		reg |= GM_GPCR_AU_ALL_DIS;
+
+		/* Is write/read necessary?  Copied from sky2_mac_init */
+		gma_write16(hw, port, GM_GP_CTRL, reg);
+		gma_read16(hw, port, GM_GP_CTRL);
+
+		switch (sky2->speed) {
+		case SPEED_1000:
+			reg &= ~GM_GPCR_SPEED_100;
+			reg |= GM_GPCR_SPEED_1000;
+			break;
+		case SPEED_100:
+			reg &= ~GM_GPCR_SPEED_1000;
+			reg |= GM_GPCR_SPEED_100;
+			break;
+		case SPEED_10:
+			reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
+			break;
+		}
+	} else
+		reg &= ~GM_GPCR_AU_ALL_DIS;
+
 	if (sky2->duplex == DUPLEX_FULL || sky2->autoneg == AUTONEG_ENABLE)
 		reg |= GM_GPCR_DUP_FULL;
 
@@ -1604,10 +1667,10 @@ static void sky2_phy_task(void *arg)
 out:
 	up(&sky2->phy_sema);
 
-	local_irq_disable();
+	spin_lock_irq(&hw->hw_lock);
 	hw->intr_mask |= (sky2->port == 0) ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2;
 	sky2_write32(hw, B0_IMSK, hw->intr_mask);
-	local_irq_enable();
+	spin_unlock_irq(&hw->hw_lock);
 }
 
 
@@ -1834,6 +1897,17 @@ static int sky2_poll(struct net_device *dev0, int *budget)
 
 	sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
 
+	/*
+	 * Kick the STAT_LEV_TIMER_CTRL timer.
+	 * This fixes my hangs on Yukon-EC (0xb6) rev 1.
+	 * The if clause is there to start the timer only if it has been
+	 * configured correctly and not been disabled via ethtool.
+	 */
+	if (sky2_read8(hw, STAT_LEV_TIMER_CTRL) == TIM_START) {
+		sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_STOP);
+		sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START);
+	}
+
 	hwidx = sky2_read16(hw, STAT_PUT_IDX);
 	BUG_ON(hwidx >= STATUS_RING_SIZE);
 	rmb();
@@ -1916,16 +1990,19 @@ exit_loop:
 	sky2_tx_check(hw, 0, tx_done[0]);
 	sky2_tx_check(hw, 1, tx_done[1]);
 
+	if (sky2_read8(hw, STAT_TX_TIMER_CTRL) == TIM_START) {
+		sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
+		sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
+	}
+
 	if (likely(work_done < to_do)) {
-		/* need to restart TX timer */
-		if (is_ec_a1(hw)) {
-			sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
-			sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
-		}
+		spin_lock_irq(&hw->hw_lock);
+		__netif_rx_complete(dev0);
 
-		netif_rx_complete(dev0);
 		hw->intr_mask |= Y2_IS_STAT_BMU;
 		sky2_write32(hw, B0_IMSK, hw->intr_mask);
+		spin_unlock_irq(&hw->hw_lock);
+
 		return 0;
 	} else {
 		*budget -= work_done;
@@ -1988,13 +2065,13 @@ static void sky2_hw_intr(struct sky2_hw *hw)
 	if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) {
 		u16 pci_err;
 
-		pci_read_config_word(hw->pdev, PCI_STATUS, &pci_err);
+		pci_err = sky2_pci_read16(hw, PCI_STATUS);
 		if (net_ratelimit())
 			printk(KERN_ERR PFX "%s: pci hw error (0x%x)\n",
 			       pci_name(hw->pdev), pci_err);
 
 		sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
-		pci_write_config_word(hw->pdev, PCI_STATUS,
+		sky2_pci_write16(hw, PCI_STATUS,
 				      pci_err | PCI_STATUS_ERROR_BITS);
 		sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
 	}
@@ -2003,7 +2080,7 @@ static void sky2_hw_intr(struct sky2_hw *hw)
 		/* PCI-Express uncorrectable Error occurred */
 		u32 pex_err;
 
-		pci_read_config_dword(hw->pdev, PEX_UNC_ERR_STAT, &pex_err);
+		pex_err = sky2_pci_read32(hw, PEX_UNC_ERR_STAT);
 
 		if (net_ratelimit())
 			printk(KERN_ERR PFX "%s: pci express error (0x%x)\n",
@@ -2011,7 +2088,7 @@ static void sky2_hw_intr(struct sky2_hw *hw)
 
 		/* clear the interrupt */
 		sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
-		pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
+		sky2_pci_write32(hw, PEX_UNC_ERR_STAT,
 				       0xffffffffUL);
 		sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
 
@@ -2057,6 +2134,7 @@ static void sky2_phy_intr(struct sky2_hw *hw, unsigned port)
 
 	hw->intr_mask &= ~(port == 0 ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2);
 	sky2_write32(hw, B0_IMSK, hw->intr_mask);
+
 	schedule_work(&sky2->phy_task);
 }
 
@@ -2070,6 +2148,7 @@ static irqreturn_t sky2_intr(int irq, void *dev_id, struct pt_regs *regs)
 	if (status == 0 || status == ~0)
 		return IRQ_NONE;
 
+	spin_lock(&hw->hw_lock);
 	if (status & Y2_IS_HW_ERR)
 		sky2_hw_intr(hw);
 
@@ -2098,7 +2177,7 @@ static irqreturn_t sky2_intr(int irq, void *dev_id, struct pt_regs *regs)
 
 	sky2_write32(hw, B0_Y2_SP_ICR, 2);
 
-	sky2_read32(hw, B0_IMSK);
+	spin_unlock(&hw->hw_lock);
 
 	return IRQ_HANDLED;
 }
@@ -2141,7 +2220,7 @@ static int sky2_reset(struct sky2_hw *hw)
 {
 	u16 status;
 	u8 t8, pmd_type;
-	int i, err;
+	int i;
 
 	sky2_write8(hw, B0_CTST, CS_RST_CLR);
 
@@ -2163,25 +2242,18 @@ static int sky2_reset(struct sky2_hw *hw)
 	sky2_write8(hw, B0_CTST, CS_RST_CLR);
 
 	/* clear PCI errors, if any */
-	err = pci_read_config_word(hw->pdev, PCI_STATUS, &status);
-	if (err)
-		goto pci_err;
+	status = sky2_pci_read16(hw, PCI_STATUS);
 
 	sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
-	err = pci_write_config_word(hw->pdev, PCI_STATUS,
-				    status | PCI_STATUS_ERROR_BITS);
-	if (err)
-		goto pci_err;
+	sky2_pci_write16(hw, PCI_STATUS, status | PCI_STATUS_ERROR_BITS);
+
 
 	sky2_write8(hw, B0_CTST, CS_MRST_CLR);
 
 	/* clear any PEX errors */
-	if (pci_find_capability(hw->pdev, PCI_CAP_ID_EXP)) {
-		err = pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
-						 0xffffffffUL);
-		if (err)
-			goto pci_err;
-	}
+	if (pci_find_capability(hw->pdev, PCI_CAP_ID_EXP)) 
+		sky2_pci_write32(hw, PEX_UNC_ERR_STAT, 0xffffffffUL);
+
 
 	pmd_type = sky2_read8(hw, B2_PMD_TYP);
 	hw->copper = !(pmd_type == 'L' || pmd_type == 'S');
@@ -2280,8 +2352,7 @@ static int sky2_reset(struct sky2_hw *hw)
 			sky2_write8(hw, STAT_FIFO_ISR_WM, 16);
 
 		sky2_write32(hw, STAT_TX_TIMER_INI, sky2_us2clk(hw, 1000));
-		sky2_write32(hw, STAT_LEV_TIMER_INI, sky2_us2clk(hw, 100));
-		sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, 20));
+		sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, 7));
 	}
 
 	/* enable status unit */
@@ -2292,14 +2363,6 @@ static int sky2_reset(struct sky2_hw *hw)
 	sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START);
 
 	return 0;
-
-pci_err:
-	/* This is to catch a BIOS bug workaround where
-	 * mmconfig table doesn't have other buses.
-	 */
-	printk(KERN_ERR PFX "%s: can't access PCI config space\n",
-	       pci_name(hw->pdev));
-	return err;
 }
 
 static u32 sky2_supported_modes(const struct sky2_hw *hw)
@@ -2823,11 +2886,11 @@ static int sky2_set_coalesce(struct net_device *dev,
 	    (ecmd->rx_coalesce_usecs_irq < tmin || ecmd->rx_coalesce_usecs_irq > tmax))
 		return -EINVAL;
 
-	if (ecmd->tx_max_coalesced_frames > 0xffff)
+	if (ecmd->tx_max_coalesced_frames >= TX_RING_SIZE-1)
 		return -EINVAL;
-	if (ecmd->rx_max_coalesced_frames > 0xff)
+	if (ecmd->rx_max_coalesced_frames > RX_MAX_PENDING)
 		return -EINVAL;
-	if (ecmd->rx_max_coalesced_frames_irq > 0xff)
+	if (ecmd->rx_max_coalesced_frames_irq >RX_MAX_PENDING)
 		return -EINVAL;
 
 	if (ecmd->tx_coalesce_usecs == 0)
@@ -3169,17 +3232,6 @@ static int __devinit sky2_probe(struct pci_dev *pdev,
 		}
 	}
 
-#ifdef __BIG_ENDIAN
-	/* byte swap descriptors in hardware */
-	{
-		u32 reg;
-
-		pci_read_config_dword(pdev, PCI_DEV_REG2, &reg);
-		reg |= PCI_REV_DESC;
-		pci_write_config_dword(pdev, PCI_DEV_REG2, reg);
-	}
-#endif
-
 	err = -ENOMEM;
 	hw = kzalloc(sizeof(*hw), GFP_KERNEL);
 	if (!hw) {
@@ -3197,6 +3249,18 @@ static int __devinit sky2_probe(struct pci_dev *pdev,
 		goto err_out_free_hw;
 	}
 	hw->pm_cap = pm_cap;
+	spin_lock_init(&hw->hw_lock);
+
+#ifdef __BIG_ENDIAN
+	/* byte swap descriptors in hardware */
+	{
+		u32 reg;
+
+		reg = sky2_pci_read32(hw, PCI_DEV_REG2);
+		reg |= PCI_REV_DESC;
+		sky2_pci_write32(hw, PCI_DEV_REG2, reg);
+	}
+#endif
 
 	/* ring for status responses */
 	hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES,
diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index fd12c289a23..3edb98075e0 100644
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -5,14 +5,22 @@
 #define _SKY2_H
 
 /* PCI config registers */
-#define PCI_DEV_REG1	0x40
-#define PCI_DEV_REG2	0x44
-#define PCI_DEV_STATUS  0x7c
-#define PCI_OS_PCI_X    (1<<26)
+enum {
+	PCI_DEV_REG1	= 0x40,
+	PCI_DEV_REG2	= 0x44,
+	PCI_DEV_STATUS  = 0x7c,
+	PCI_DEV_REG3	= 0x80,
+	PCI_DEV_REG4	= 0x84,
+	PCI_DEV_REG5    = 0x88,
+};
 
-#define PEX_LNK_STAT	0xf2
-#define PEX_UNC_ERR_STAT 0x104
-#define PEX_DEV_CTRL	0xe8
+enum {
+	PEX_DEV_CAP	= 0xe4,
+	PEX_DEV_CTRL	= 0xe8,
+	PEX_DEV_STA	= 0xea,
+	PEX_LNK_STAT	= 0xf2,
+	PEX_UNC_ERR_STAT= 0x104,
+};
 
 /* Yukon-2 */
 enum pci_dev_reg_1 {
@@ -37,6 +45,25 @@ enum pci_dev_reg_2 {
 	PCI_USEDATA64	= 1<<0,		/* Use 64Bit Data bus ext */
 };
 
+/*	PCI_OUR_REG_4		32 bit	Our Register 4 (Yukon-ECU only) */
+enum pci_dev_reg_4 {
+					/* (Link Training & Status State Machine) */
+	P_TIMER_VALUE_MSK	= 0xffL<<16,	/* Bit 23..16:	Timer Value Mask */
+					/* (Active State Power Management) */
+	P_FORCE_ASPM_REQUEST	= 1<<15, /* Force ASPM Request (A1 only) */
+	P_ASPM_GPHY_LINK_DOWN	= 1<<14, /* GPHY Link Down (A1 only) */
+	P_ASPM_INT_FIFO_EMPTY	= 1<<13, /* Internal FIFO Empty (A1 only) */
+	P_ASPM_CLKRUN_REQUEST	= 1<<12, /* CLKRUN Request (A1 only) */
+
+	P_ASPM_FORCE_CLKREQ_ENA	= 1<<4,	/* Force CLKREQ Enable (A1b only) */
+	P_ASPM_CLKREQ_PAD_CTL	= 1<<3,	/* CLKREQ PAD Control (A1 only) */
+	P_ASPM_A1_MODE_SELECT	= 1<<2,	/* A1 Mode Select (A1 only) */
+	P_CLK_GATE_PEX_UNIT_ENA	= 1<<1,	/* Enable Gate PEX Unit Clock */
+	P_CLK_GATE_ROOT_COR_ENA	= 1<<0,	/* Enable Gate Root Core Clock */
+	P_ASPM_CONTROL_MSK	= P_FORCE_ASPM_REQUEST | P_ASPM_GPHY_LINK_DOWN
+				  | P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY,
+};
+
 
 #define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
 			       PCI_STATUS_SIG_SYSTEM_ERROR | \
@@ -507,6 +534,16 @@ enum {
 };
 #define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
 
+/*	Q_F				32 bit	Flag Register */
+enum {
+	F_ALM_FULL	= 1<<27, /* Rx FIFO: almost full */
+	F_EMPTY		= 1<<27, /* Tx FIFO: empty flag */
+	F_FIFO_EOF	= 1<<26, /* Tag (EOF Flag) bit in FIFO */
+	F_WM_REACHED	= 1<<25, /* Watermark reached */
+	F_M_RX_RAM_DIS	= 1<<24, /* MAC Rx RAM Read Port disable */
+	F_FIFO_LEVEL	= 0x1fL<<16, /* Bit 23..16:	# of Qwords in FIFO */
+	F_WATER_MARK	= 0x0007ffL, /* Bit 10.. 0:	Watermark */
+};
 
 /* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
 enum {
@@ -909,10 +946,12 @@ enum {
 	PHY_BCOM_ID1_C0	= 0x6044,
 	PHY_BCOM_ID1_C5	= 0x6047,
 
-	PHY_MARV_ID1_B0	= 0x0C23, /* Yukon (PHY 88E1011) */
+	PHY_MARV_ID1_B0	= 0x0C23, /* Yukon 	(PHY 88E1011) */
 	PHY_MARV_ID1_B2	= 0x0C25, /* Yukon-Plus (PHY 88E1011) */
-	PHY_MARV_ID1_C2	= 0x0CC2, /* Yukon-EC (PHY 88E1111) */
-	PHY_MARV_ID1_Y2	= 0x0C91, /* Yukon-2 (PHY 88E1112) */
+	PHY_MARV_ID1_C2	= 0x0CC2, /* Yukon-EC	(PHY 88E1111) */
+	PHY_MARV_ID1_Y2	= 0x0C91, /* Yukon-2	(PHY 88E1112) */
+	PHY_MARV_ID1_FE = 0x0C83, /* Yukon-FE   (PHY 88E3082 Rev.A1) */
+	PHY_MARV_ID1_ECU= 0x0CB0, /* Yukon-ECU  (PHY 88E1149 Rev.B2?) */
 };
 
 /* Advertisement register bits */
@@ -1837,8 +1876,9 @@ struct sky2_port {
 struct sky2_hw {
 	void __iomem  	     *regs;
 	struct pci_dev	     *pdev;
-	u32		     intr_mask;
 	struct net_device    *dev[2];
+	spinlock_t	     hw_lock;
+	u32		     intr_mask;
 
 	int		     pm_cap;
 	int		     msi;
@@ -1912,4 +1952,25 @@ static inline void gma_set_addr(struct sky2_hw *hw, unsigned port, unsigned reg,
 	gma_write16(hw, port, reg+4,(u16) addr[2] | ((u16) addr[3] << 8));
 	gma_write16(hw, port, reg+8,(u16) addr[4] | ((u16) addr[5] << 8));
 }
+
+/* PCI config space access */
+static inline u32 sky2_pci_read32(const struct sky2_hw *hw, unsigned reg)
+{
+	return sky2_read32(hw, Y2_CFG_SPC + reg);
+}
+
+static inline u16 sky2_pci_read16(const struct sky2_hw *hw, unsigned reg)
+{
+	return sky2_read16(hw, Y2_CFG_SPC + reg);
+}
+
+static inline void sky2_pci_write32(struct sky2_hw *hw, unsigned reg, u32 val)
+{
+	sky2_write32(hw, Y2_CFG_SPC + reg, val);
+}
+
+static inline void sky2_pci_write16(struct sky2_hw *hw, unsigned reg, u16 val)
+{
+	sky2_write16(hw, Y2_CFG_SPC + reg, val);
+}
 #endif
diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c
index e7dc653d5bd..e8e92c853e8 100644
--- a/drivers/net/tg3.c
+++ b/drivers/net/tg3.c
@@ -9408,6 +9408,15 @@ static int __devinit tg3_is_sun_570X(struct tg3 *tp)
 			return 0;
 		if (venid == PCI_VENDOR_ID_SUN)
 			return 1;
+
+		/* TG3 chips onboard the SunBlade-2500 don't have the
+		 * subsystem-vendor-id set to PCI_VENDOR_ID_SUN but they
+		 * are distinguishable from non-Sun variants by being
+		 * named "network" by the firmware.  Non-Sun cards will
+		 * show up as being named "ethernet".
+		 */
+		if (!strcmp(pcp->prom_name, "network"))
+			return 1;
 	}
 	return 0;
 }
diff --git a/drivers/net/tlan.c b/drivers/net/tlan.c
index c2506b56a18..12076f8f942 100644
--- a/drivers/net/tlan.c
+++ b/drivers/net/tlan.c
@@ -536,6 +536,7 @@ static int __devinit TLan_probe1(struct pci_dev *pdev,
 	u16		   device_id;
 	int		   reg, rc = -ENODEV;
 
+#ifdef CONFIG_PCI
 	if (pdev) {
 		rc = pci_enable_device(pdev);
 		if (rc)
@@ -547,6 +548,7 @@ static int __devinit TLan_probe1(struct pci_dev *pdev,
 			goto err_out;
 		}
 	}
+#endif  /*  CONFIG_PCI  */
 
 	dev = alloc_etherdev(sizeof(TLanPrivateInfo));
 	if (dev == NULL) {
diff --git a/drivers/net/tokenring/smctr.h b/drivers/net/tokenring/smctr.h
index b306c7e4c79..88dfa2e01d6 100644
--- a/drivers/net/tokenring/smctr.h
+++ b/drivers/net/tokenring/smctr.h
@@ -1042,7 +1042,7 @@ typedef struct net_local {
         __u16            functional_address[2];
         __u16            bitwise_group_address[2];
 
-	__u8            *ptr_ucode;
+	const __u8       *ptr_ucode;
 
 	__u8		cleanup;
 
diff --git a/drivers/net/wireless/ipw2200.c b/drivers/net/wireless/ipw2200.c
index 30b13a6e6fd..ed37141319e 100644
--- a/drivers/net/wireless/ipw2200.c
+++ b/drivers/net/wireless/ipw2200.c
@@ -4636,9 +4636,9 @@ static void ipw_rx_notification(struct ipw_priv *priv,
 		}
 
 	default:
-		IPW_ERROR("Unknown notification: "
-			  "subtype=%d,flags=0x%2x,size=%d\n",
-			  notif->subtype, notif->flags, notif->size);
+		IPW_DEBUG_NOTIF("Unknown notification: "
+				"subtype=%d,flags=0x%2x,size=%d\n",
+				notif->subtype, notif->flags, notif->size);
 	}
 }
 
diff --git a/drivers/net/wireless/wavelan_cs.c b/drivers/net/wireless/wavelan_cs.c
index cf373625fc7..98122f3a4bc 100644
--- a/drivers/net/wireless/wavelan_cs.c
+++ b/drivers/net/wireless/wavelan_cs.c
@@ -950,16 +950,8 @@ wv_82593_cmd(struct net_device *	dev,
 static inline int
 wv_diag(struct net_device *	dev)
 {
-  int		ret = FALSE;
-
-  if(wv_82593_cmd(dev, "wv_diag(): diagnose",
-		  OP0_DIAGNOSE, SR0_DIAGNOSE_PASSED))
-    ret = TRUE;
-
-#ifdef DEBUG_CONFIG_ERRORS
-  printk(KERN_INFO "wavelan_cs: i82593 Self Test failed!\n");
-#endif
-  return(ret);
+  return(wv_82593_cmd(dev, "wv_diag(): diagnose",
+		      OP0_DIAGNOSE, SR0_DIAGNOSE_PASSED));
 } /* wv_diag */
 
 /*------------------------------------------------------------------*/
@@ -3604,8 +3596,8 @@ wv_82593_config(struct net_device *	dev)
   cfblk.lin_prio = 0;   	/* conform to 802.3 backoff algoritm */
   cfblk.exp_prio = 5;	        /* conform to 802.3 backoff algoritm */
   cfblk.bof_met = 1;	        /* conform to 802.3 backoff algoritm */
-  cfblk.ifrm_spc = 0x20;	/* 32 bit times interframe spacing */
-  cfblk.slottim_low = 0x20;	/* 32 bit times slot time */
+  cfblk.ifrm_spc = 0x20 >> 4;	/* 32 bit times interframe spacing */
+  cfblk.slottim_low = 0x20 >> 5;	/* 32 bit times slot time */
   cfblk.slottim_hi = 0x0;
   cfblk.max_retr = 15;
   cfblk.prmisc = ((lp->promiscuous) ? TRUE: FALSE);	/* Promiscuous mode */
diff --git a/drivers/s390/block/Kconfig b/drivers/s390/block/Kconfig
index 6912399d093..6f50cc9323d 100644
--- a/drivers/s390/block/Kconfig
+++ b/drivers/s390/block/Kconfig
@@ -55,21 +55,13 @@ config DASD_DIAG
 	  Disks under VM.  If you are not running under VM or unsure what it is,
 	  say "N".
 
-config DASD_EER
-	tristate "Extended error reporting (EER)"
-	depends on DASD
-	help
-	  This driver provides a character device interface to the
-          DASD extended error reporting. This is only needed if you want to
-          use applications written for the EER facility.
-
 config DASD_CMB
 	tristate "Compatibility interface for DASD channel measurement blocks"
 	depends on DASD
 	help
-	  This driver provides an additional interface to the channel
-          measurement facility, which is normally accessed though sysfs, with
-          a set of ioctl functions specific to the dasd driver.
+	  This driver provides an additional interface to the channel measurement
+	  facility, which is normally accessed though sysfs, with a set of
+	  ioctl functions specific to the dasd driver.
 	  This is only needed if you want to use applications written for
 	  linux-2.4 dasd channel measurement facility interface.
 
diff --git a/drivers/s390/block/Makefile b/drivers/s390/block/Makefile
index 0c0d871e8f5..58c6780134f 100644
--- a/drivers/s390/block/Makefile
+++ b/drivers/s390/block/Makefile
@@ -5,7 +5,6 @@
 dasd_eckd_mod-objs := dasd_eckd.o dasd_3990_erp.o dasd_9343_erp.o
 dasd_fba_mod-objs  := dasd_fba.o dasd_3370_erp.o dasd_9336_erp.o
 dasd_diag_mod-objs := dasd_diag.o
-dasd_eer_mod-objs := dasd_eer.o
 dasd_mod-objs      := dasd.o dasd_ioctl.o dasd_proc.o dasd_devmap.o \
 			dasd_genhd.o dasd_erp.o
 
@@ -14,6 +13,5 @@ obj-$(CONFIG_DASD_DIAG) += dasd_diag_mod.o
 obj-$(CONFIG_DASD_ECKD) += dasd_eckd_mod.o
 obj-$(CONFIG_DASD_FBA)  += dasd_fba_mod.o
 obj-$(CONFIG_DASD_CMB)  += dasd_cmb.o
-obj-$(CONFIG_DASD_EER)  += dasd_eer.o
 obj-$(CONFIG_BLK_DEV_XPRAM) += xpram.o
 obj-$(CONFIG_DCSSBLK) += dcssblk.o
diff --git a/drivers/s390/block/dasd.c b/drivers/s390/block/dasd.c
index 08c88fcd896..af1d5b404ce 100644
--- a/drivers/s390/block/dasd.c
+++ b/drivers/s390/block/dasd.c
@@ -18,7 +18,6 @@
 #include <linux/slab.h>
 #include <linux/buffer_head.h>
 #include <linux/hdreg.h>
-#include <linux/notifier.h>
 
 #include <asm/ccwdev.h>
 #include <asm/ebcdic.h>
@@ -58,7 +57,6 @@ static void dasd_int_handler(struct ccw_device *, unsigned long, struct irb *);
 static void dasd_flush_ccw_queue(struct dasd_device *, int);
 static void dasd_tasklet(struct dasd_device *);
 static void do_kick_device(void *data);
-static void dasd_disable_eer(struct dasd_device *device);
 
 /*
  * SECTION: Operations on the device structure.
@@ -153,10 +151,13 @@ dasd_state_new_to_known(struct dasd_device *device)
 static inline void
 dasd_state_known_to_new(struct dasd_device * device)
 {
-	/* disable extended error reporting for this device */
-	dasd_disable_eer(device);
 	/* Forget the discipline information. */
+	if (device->discipline)
+		module_put(device->discipline->owner);
 	device->discipline = NULL;
+	if (device->base_discipline)
+		module_put(device->base_discipline->owner);
+	device->base_discipline = NULL;
 	device->state = DASD_STATE_NEW;
 
 	dasd_free_queue(device);
@@ -871,9 +872,6 @@ dasd_handle_state_change_pending(struct dasd_device *device)
 	struct dasd_ccw_req *cqr;
 	struct list_head *l, *n;
 
-	/* first of all call extended error reporting */
-	dasd_write_eer_trigger(DASD_EER_STATECHANGE, device, NULL);
-
 	device->stopped &= ~DASD_STOPPED_PENDING;
 
         /* restart all 'running' IO on queue */
@@ -1093,19 +1091,6 @@ restart:
 			}
 			goto restart;
 		}
-
-		/* first of all call extended error reporting */
-		if (device->eer && cqr->status == DASD_CQR_FAILED) {
-			dasd_write_eer_trigger(DASD_EER_FATALERROR,
-					       device, cqr);
-
-			/* restart request  */
-			cqr->status = DASD_CQR_QUEUED;
-			cqr->retries = 255;
-			device->stopped |= DASD_STOPPED_QUIESCE;
-			goto restart;
-		}
-
 		/* Process finished ERP request. */
 		if (cqr->refers) {
 			__dasd_process_erp(device, cqr);
@@ -1243,8 +1228,7 @@ __dasd_start_head(struct dasd_device * device)
 	cqr = list_entry(device->ccw_queue.next, struct dasd_ccw_req, list);
         /* check FAILFAST */
 	if (device->stopped & ~DASD_STOPPED_PENDING &&
-	    test_bit(DASD_CQR_FLAGS_FAILFAST, &cqr->flags) &&
-	    (!device->eer)) {
+	    test_bit(DASD_CQR_FLAGS_FAILFAST, &cqr->flags)) {
 		cqr->status = DASD_CQR_FAILED;
 		dasd_schedule_bh(device);
 	}
@@ -1880,9 +1864,10 @@ dasd_generic_remove (struct ccw_device *cdev)
  */
 int
 dasd_generic_set_online (struct ccw_device *cdev,
-			 struct dasd_discipline *discipline)
+			 struct dasd_discipline *base_discipline)
 
 {
+	struct dasd_discipline *discipline;
 	struct dasd_device *device;
 	int rc;
 
@@ -1890,6 +1875,7 @@ dasd_generic_set_online (struct ccw_device *cdev,
 	if (IS_ERR(device))
 		return PTR_ERR(device);
 
+	discipline = base_discipline;
 	if (device->features & DASD_FEATURE_USEDIAG) {
 	  	if (!dasd_diag_discipline_pointer) {
 		        printk (KERN_WARNING
@@ -1901,6 +1887,16 @@ dasd_generic_set_online (struct ccw_device *cdev,
 		}
 		discipline = dasd_diag_discipline_pointer;
 	}
+	if (!try_module_get(base_discipline->owner)) {
+		dasd_delete_device(device);
+		return -EINVAL;
+	}
+	if (!try_module_get(discipline->owner)) {
+		module_put(base_discipline->owner);
+		dasd_delete_device(device);
+		return -EINVAL;
+	}
+	device->base_discipline = base_discipline;
 	device->discipline = discipline;
 
 	rc = discipline->check_device(device);
@@ -1909,6 +1905,8 @@ dasd_generic_set_online (struct ccw_device *cdev,
 			"dasd_generic couldn't online device %s "
 			"with discipline %s rc=%i\n",
 			cdev->dev.bus_id, discipline->name, rc);
+		module_put(discipline->owner);
+		module_put(base_discipline->owner);
 		dasd_delete_device(device);
 		return rc;
 	}
@@ -1986,9 +1984,6 @@ dasd_generic_notify(struct ccw_device *cdev, int event)
 	switch (event) {
 	case CIO_GONE:
 	case CIO_NO_PATH:
-		/* first of all call extended error reporting */
-		dasd_write_eer_trigger(DASD_EER_NOPATH, device, NULL);
-
 		if (device->state < DASD_STATE_BASIC)
 			break;
 		/* Device is active. We want to keep it. */
@@ -2046,51 +2041,6 @@ dasd_generic_auto_online (struct ccw_driver *dasd_discipline_driver)
 	put_driver(drv);
 }
 
-/*
- * notifications for extended error reports
- */
-static struct notifier_block *dasd_eer_chain;
-
-int
-dasd_register_eer_notifier(struct notifier_block *nb)
-{
-	return notifier_chain_register(&dasd_eer_chain, nb);
-}
-
-int
-dasd_unregister_eer_notifier(struct notifier_block *nb)
-{
-	return notifier_chain_unregister(&dasd_eer_chain, nb);
-}
-
-/*
- * Notify the registered error reporting module of a problem
- */
-void
-dasd_write_eer_trigger(unsigned int id, struct dasd_device *device,
-		       struct dasd_ccw_req *cqr)
-{
-	if (device->eer) {
-		struct dasd_eer_trigger temp;
-		temp.id = id;
-		temp.device = device;
-		temp.cqr = cqr;
-		notifier_call_chain(&dasd_eer_chain, DASD_EER_TRIGGER,
-				    (void *)&temp);
-	}
-}
-
-/*
- * Tell the registered error reporting module to disable error reporting for
- * a given device and to cleanup any private data structures on that device.
- */
-static void
-dasd_disable_eer(struct dasd_device *device)
-{
-	notifier_call_chain(&dasd_eer_chain, DASD_EER_DISABLE, (void *)device);
-}
-
-
 static int __init
 dasd_init(void)
 {
@@ -2172,11 +2122,6 @@ EXPORT_SYMBOL_GPL(dasd_generic_set_online);
 EXPORT_SYMBOL_GPL(dasd_generic_set_offline);
 EXPORT_SYMBOL_GPL(dasd_generic_auto_online);
 
-EXPORT_SYMBOL(dasd_register_eer_notifier);
-EXPORT_SYMBOL(dasd_unregister_eer_notifier);
-EXPORT_SYMBOL(dasd_write_eer_trigger);
-
-
 /*
  * Overrides for Emacs so that we follow Linus's tabbing style.
  * Emacs will notice this stuff at the end of the file and automatically
diff --git a/drivers/s390/block/dasd_3990_erp.c b/drivers/s390/block/dasd_3990_erp.c
index c811380b907..4ee0f934e32 100644
--- a/drivers/s390/block/dasd_3990_erp.c
+++ b/drivers/s390/block/dasd_3990_erp.c
@@ -1108,9 +1108,6 @@ dasd_3990_handle_env_data(struct dasd_ccw_req * erp, char *sense)
 		case 0x0B:
 			DEV_MESSAGE(KERN_WARNING, device, "%s",
 				    "FORMAT F - Volume is suspended duplex");
-			/* call extended error reporting (EER) */
-			dasd_write_eer_trigger(DASD_EER_PPRCSUSPEND, device,
-					       erp->refers);
 			break;
 		case 0x0C:
 			DEV_MESSAGE(KERN_WARNING, device, "%s",
diff --git a/drivers/s390/block/dasd_eckd.h b/drivers/s390/block/dasd_eckd.h
index e15dd797805..bc3823d3522 100644
--- a/drivers/s390/block/dasd_eckd.h
+++ b/drivers/s390/block/dasd_eckd.h
@@ -29,7 +29,6 @@
 #define DASD_ECKD_CCW_PSF		 0x27
 #define DASD_ECKD_CCW_RSSD		 0x3e
 #define DASD_ECKD_CCW_LOCATE_RECORD	 0x47
-#define DASD_ECKD_CCW_SNSS               0x54
 #define DASD_ECKD_CCW_DEFINE_EXTENT	 0x63
 #define DASD_ECKD_CCW_WRITE_MT		 0x85
 #define DASD_ECKD_CCW_READ_MT		 0x86
diff --git a/drivers/s390/block/dasd_eer.c b/drivers/s390/block/dasd_eer.c
deleted file mode 100644
index f70cd7716b2..00000000000
--- a/drivers/s390/block/dasd_eer.c
+++ /dev/null
@@ -1,1090 +0,0 @@
-/*
- *	character device driver for extended error reporting
- *
- *
- *	Copyright (C) 2005 IBM Corporation
- *	extended error reporting for DASD ECKD devices
- *	Author(s): Stefan Weinhuber <wein@de.ibm.com>
- *
- */
-
-#include <linux/init.h>
-#include <linux/fs.h>
-#include <linux/kernel.h>
-#include <linux/miscdevice.h>
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/device.h>
-#include <linux/workqueue.h>
-#include <linux/poll.h>
-#include <linux/notifier.h>
-
-#include <asm/uaccess.h>
-#include <asm/semaphore.h>
-#include <asm/atomic.h>
-#include <asm/ebcdic.h>
-
-#include "dasd_int.h"
-#include "dasd_eckd.h"
-
-
-MODULE_LICENSE("GPL");
-
-MODULE_AUTHOR("Stefan Weinhuber <wein@de.ibm.com>");
-MODULE_DESCRIPTION("DASD extended error reporting module");
-
-
-#ifdef PRINTK_HEADER
-#undef PRINTK_HEADER
-#endif				/* PRINTK_HEADER */
-#define PRINTK_HEADER "dasd(eer):"
-
-
-
-
-
-/*****************************************************************************/
-/*      the internal buffer                                                  */
-/*****************************************************************************/
-
-/*
- * The internal buffer is meant to store obaque blobs of data, so it doesn't
- * know of higher level concepts like triggers.
- * It consists of a number of pages that are used as a ringbuffer. Each data
- * blob is stored in a simple record that consists of an integer, which
- * contains the size of the following data, and the data bytes themselfes.
- *
- * To allow for multiple independent readers we create one internal buffer
- * each time the device is opened and destroy the buffer when the file is
- * closed again.
- *
- * One record can be written to a buffer by using the functions
- * - dasd_eer_start_record (one time per record to write the size to the buffer
- *                          and reserve the space for the data)
- * - dasd_eer_write_buffer (one or more times per record to write the data)
- * The data can be written in several steps but you will have to compute
- * the total size up front for the invocation of dasd_eer_start_record.
- * If the ringbuffer is full, dasd_eer_start_record will remove the required
- * number of old records.
- *
- * A record is typically read in two steps, first read the integer that
- * specifies the size of the following data, then read the data.
- * Both can be done by
- * - dasd_eer_read_buffer
- *
- * For all mentioned functions you need to get the bufferlock first and keep it
- * until a complete record is written or read.
- */
-
-
-/*
- * Alle information necessary to keep track of an internal buffer is kept in
- * a struct eerbuffer. The buffer specific to a file pointer is strored in
- * the private_data field of that file. To be able to write data to all
- * existing buffers, each buffer is also added to the bufferlist.
- * If the user doesn't want to read a complete record in one go, we have to
- * keep track of the rest of the record. residual stores the number of bytes
- * that are still to deliver. If the rest of the record is invalidated between
- * two reads then residual will be set to -1 so that the next read will fail.
- * All entries in the eerbuffer structure are protected with the bufferlock.
- * To avoid races between writing to a buffer on the one side and creating
- * and destroying buffers on the other side, the bufferlock must also be used
- * to protect the bufferlist.
- */
-
-struct eerbuffer {
-	struct list_head list;
-	char **buffer;
-	int buffersize;
-	int buffer_page_count;
-	int head;
-        int tail;
-	int residual;
-};
-
-LIST_HEAD(bufferlist);
-
-static spinlock_t bufferlock = SPIN_LOCK_UNLOCKED;
-
-DECLARE_WAIT_QUEUE_HEAD(dasd_eer_read_wait_queue);
-
-/*
- * How many free bytes are available on the buffer.
- * needs to be called with bufferlock held
- */
-static int
-dasd_eer_get_free_bytes(struct eerbuffer *eerb)
-{
-	if (eerb->head < eerb->tail) {
-		return eerb->tail - eerb->head - 1;
-	} else
-		return eerb->buffersize - eerb->head + eerb->tail -1;
-}
-
-/*
- * How many bytes of buffer space are used.
- * needs to be called with bufferlock held
- */
-static int
-dasd_eer_get_filled_bytes(struct eerbuffer *eerb)
-{
-
-	if (eerb->head >= eerb->tail) {
-		return eerb->head - eerb->tail;
-	} else
-		return eerb->buffersize - eerb->tail + eerb->head;
-}
-
-/*
- * The dasd_eer_write_buffer function just copies count bytes of data
- * to the buffer. Make sure to call dasd_eer_start_record first, to
- * make sure that enough free space is available.
- * needs to be called with bufferlock held
- */
-static void
-dasd_eer_write_buffer(struct eerbuffer *eerb, int count, char *data)
-{
-
-	unsigned long headindex,localhead;
-	unsigned long rest, len;
-	char *nextdata;
-
-	nextdata = data;
-	rest = count;
-	while (rest > 0) {
- 		headindex = eerb->head / PAGE_SIZE;
- 		localhead = eerb->head % PAGE_SIZE;
-		len = min(rest, (PAGE_SIZE - localhead));
-		memcpy(eerb->buffer[headindex]+localhead, nextdata, len);
-		nextdata += len;
-		rest -= len;
-		eerb->head += len;
-		if ( eerb->head == eerb->buffersize )
-			eerb->head = 0; /* wrap around */
-		if (eerb->head > eerb->buffersize) {
-			MESSAGE(KERN_ERR, "%s", "runaway buffer head.");
-			BUG();
-		}
-	}
-}
-
-/*
- * needs to be called with bufferlock held
- */
-static int
-dasd_eer_read_buffer(struct eerbuffer *eerb, int count, char *data)
-{
-
-	unsigned long tailindex,localtail;
-	unsigned long rest, len, finalcount;
-	char *nextdata;
-
-	finalcount = min(count, dasd_eer_get_filled_bytes(eerb));
-	nextdata = data;
-	rest = finalcount;
-	while (rest > 0) {
- 		tailindex = eerb->tail / PAGE_SIZE;
- 		localtail = eerb->tail % PAGE_SIZE;
-		len = min(rest, (PAGE_SIZE - localtail));
-		memcpy(nextdata, eerb->buffer[tailindex]+localtail, len);
-		nextdata += len;
-		rest -= len;
-		eerb->tail += len;
-		if ( eerb->tail == eerb->buffersize )
-			eerb->tail = 0; /* wrap around */
-		if (eerb->tail > eerb->buffersize) {
-			MESSAGE(KERN_ERR, "%s", "runaway buffer tail.");
-			BUG();
-		}
-	}
-	return finalcount;
-}
-
-/*
- * Whenever you want to write a blob of data to the internal buffer you
- * have to start by using this function first. It will write the number
- * of bytes that will be written to the buffer. If necessary it will remove
- * old records to make room for the new one.
- * needs to be called with bufferlock held
- */
-static int
-dasd_eer_start_record(struct eerbuffer *eerb, int count)
-{
-	int tailcount;
-	if (count + sizeof(count) > eerb->buffersize)
-		return -ENOMEM;
-	while (dasd_eer_get_free_bytes(eerb) < count + sizeof(count)) {
-		if (eerb->residual > 0) {
-			eerb->tail += eerb->residual;
-			if (eerb->tail >= eerb->buffersize)
-				eerb->tail -= eerb->buffersize;
-			eerb->residual = -1;
-		}
-		dasd_eer_read_buffer(eerb, sizeof(tailcount),
-				     (char*)(&tailcount));
-		eerb->tail += tailcount;
-		if (eerb->tail >= eerb->buffersize)
-			eerb->tail -= eerb->buffersize;
-	}
-	dasd_eer_write_buffer(eerb, sizeof(count), (char*)(&count));
-
-	return 0;
-};
-
-/*
- * release pages that are not used anymore
- */
-static void
-dasd_eer_free_buffer_pages(char **buf, int no_pages)
-{
-	int i;
-
-	for (i = 0; i < no_pages; ++i) {
-		free_page((unsigned long)buf[i]);
-	}
-}
-
-/*
- * allocate a new set of memory pages
- */
-static int
-dasd_eer_allocate_buffer_pages(char **buf, int no_pages)
-{
-	int i;
-
-	for (i = 0; i < no_pages; ++i) {
-		buf[i] = (char *) get_zeroed_page(GFP_KERNEL);
-		if (!buf[i]) {
-			dasd_eer_free_buffer_pages(buf, i);
-			return -ENOMEM;
-		}
-	}
-	return 0;
-}
-
-/*
- * empty the buffer by resetting head and tail
- * In case there is a half read data blob in the buffer, we set residual
- * to -1 to indicate that the remainder of the blob is lost.
- */
-static void
-dasd_eer_purge_buffer(struct eerbuffer *eerb)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&bufferlock, flags);
-	if (eerb->residual > 0)
-		eerb->residual = -1;
-	eerb->tail=0;
-	eerb->head=0;
-	spin_unlock_irqrestore(&bufferlock, flags);
-}
-
-/*
- * set the size of the buffer, newsize is the new number of pages to be used
- * we don't try to copy any data back an forth, so any resize will also purge
- * the buffer
- */
-static int
-dasd_eer_resize_buffer(struct eerbuffer *eerb, int newsize)
-{
-	int i, oldcount, reuse;
-	char **new;
-	char **old;
-	unsigned long flags;
-
-	if (newsize < 1)
-		return -EINVAL;
-	if (eerb->buffer_page_count == newsize) {
-		/* documented behaviour is that any successfull invocation
-                 * will purge all records */
-		dasd_eer_purge_buffer(eerb);
-		return 0;
-	}
-	new = kmalloc(newsize*sizeof(char*), GFP_KERNEL);
-	if (!new)
-		return -ENOMEM;
-
-	reuse=min(eerb->buffer_page_count, newsize);
-	for (i = 0; i < reuse; ++i) {
-		new[i] = eerb->buffer[i];
-	}
-	if (eerb->buffer_page_count < newsize) {
-		if (dasd_eer_allocate_buffer_pages(
-			    &new[eerb->buffer_page_count],
-			    newsize - eerb->buffer_page_count)) {
-			kfree(new);
-			return -ENOMEM;
-		}
-	}
-
-	spin_lock_irqsave(&bufferlock, flags);
-	old = eerb->buffer;
-	eerb->buffer = new;
-	if (eerb->residual > 0)
-		eerb->residual = -1;
-	eerb->tail = 0;
-	eerb->head = 0;
-	oldcount = eerb->buffer_page_count;
-	eerb->buffer_page_count = newsize;
-	spin_unlock_irqrestore(&bufferlock, flags);
-
-	if (oldcount > newsize) {
-		for (i = newsize; i < oldcount; ++i) {
-			free_page((unsigned long)old[i]);
-		}
-	}
-	kfree(old);
-
-	return 0;
-}
-
-
-/*****************************************************************************/
-/*      The extended error reporting functionality                           */
-/*****************************************************************************/
-
-/*
- * When a DASD device driver wants to report an error, it calls the
- * function dasd_eer_write_trigger (via a notifier mechanism) and gives the
- * respective trigger ID as parameter.
- * Currently there are four kinds of triggers:
- *
- * DASD_EER_FATALERROR:  all kinds of unrecoverable I/O problems
- * DASD_EER_PPRCSUSPEND: PPRC was suspended
- * DASD_EER_NOPATH:      There is no path to the device left.
- * DASD_EER_STATECHANGE: The state of the device has changed.
- *
- * For the first three triggers all required information can be supplied by
- * the caller. For these triggers a record is written by the function
- * dasd_eer_write_standard_trigger.
- *
- * When dasd_eer_write_trigger is called to write a DASD_EER_STATECHANGE
- * trigger, we have to gather the necessary sense data first. We cannot queue
- * the necessary SNSS (sense subsystem status) request immediatly, since we
- * are likely to run in a deadlock situation. Instead, we schedule a
- * work_struct that calls the function dasd_eer_sense_subsystem_status to
- * create and start an SNSS  request asynchronously.
- *
- * To avoid memory allocations at runtime, the necessary memory is allocated
- * when the extended error reporting is enabled for a device (by
- * dasd_eer_probe). There is one private eer data structure for each eer
- * enabled DASD device. It contains memory for the work_struct, one SNSS cqr
- * and a flags field that is used to coordinate the use of the cqr. The call
- * to write a state change trigger can come in at any time, so we have one flag
- * CQR_IN_USE that protects the cqr itself. When this flag indicates that the
- * cqr is currently in use, dasd_eer_sense_subsystem_status cannot start a
- * second request but sets the SNSS_REQUESTED flag instead.
- *
- * When the request is finished, the callback function dasd_eer_SNSS_cb
- * is called. This function will invoke the function
- * dasd_eer_write_SNSS_trigger to finally write the trigger. It will also
- * check the SNSS_REQUESTED flag and if it is set it will call
- * dasd_eer_sense_subsystem_status again.
- *
- * To avoid race conditions during the handling of the lock, the flags must
- * be protected by the snsslock.
- */
-
-struct dasd_eer_private {
-	struct dasd_ccw_req *cqr;
-	unsigned long flags;
-	struct work_struct worker;
-};
-
-static void dasd_eer_destroy(struct dasd_device *device,
-			     struct dasd_eer_private *eer);
-static int
-dasd_eer_write_trigger(struct dasd_eer_trigger *trigger);
-static void dasd_eer_sense_subsystem_status(void *data);
-static int dasd_eer_notify(struct notifier_block *self,
-			   unsigned long action, void *data);
-
-struct workqueue_struct *dasd_eer_workqueue;
-
-#define SNSS_DATA_SIZE 44
-static spinlock_t snsslock = SPIN_LOCK_UNLOCKED;
-
-#define DASD_EER_BUSID_SIZE 10
-struct dasd_eer_header {
-	__u32 total_size;
-	__u32 trigger;
-	__u64 tv_sec;
-	__u64 tv_usec;
-	char busid[DASD_EER_BUSID_SIZE];
-} __attribute__ ((packed));
-
-static struct notifier_block dasd_eer_nb = {
-	.notifier_call = dasd_eer_notify,
-};
-
-/*
- * flags for use with dasd_eer_private
- */
-#define CQR_IN_USE     0
-#define SNSS_REQUESTED 1
-
-/*
- * This function checks if extended error reporting is available for a given
- * dasd_device. If yes, then it creates and returns a struct dasd_eer,
- * otherwise it returns an -EPERM error pointer.
- */
-struct dasd_eer_private *
-dasd_eer_probe(struct dasd_device *device)
-{
-	struct dasd_eer_private *private;
-
-	if (!(device && device->discipline
-	      && !strcmp(device->discipline->name, "ECKD"))) {
-		return ERR_PTR(-EPERM);
-	}
-	/* allocate the private data structure */
-	private = (struct dasd_eer_private *)kmalloc(
-		sizeof(struct dasd_eer_private), GFP_KERNEL);
-	if (!private) {
-		return ERR_PTR(-ENOMEM);
-	}
-	INIT_WORK(&private->worker, dasd_eer_sense_subsystem_status,
-		  (void *)device);
-	private->cqr = dasd_kmalloc_request("ECKD",
-					    1 /* SNSS */ ,
-					    SNSS_DATA_SIZE ,
-					    device);
-	if (!private->cqr) {
-		kfree(private);
-		return ERR_PTR(-ENOMEM);
-	}
-	private->flags = 0;
-	return private;
-};
-
-/*
- * If our private SNSS request is queued, remove it from the
- * dasd ccw queue so we can free the requests memory.
- */
-static void
-dasd_eer_dequeue_SNSS_request(struct dasd_device *device,
-			      struct dasd_eer_private *eer)
-{
-	struct list_head *lst, *nxt;
-	struct dasd_ccw_req *cqr, *erpcqr;
-	dasd_erp_fn_t erp_fn;
-
-	spin_lock_irq(get_ccwdev_lock(device->cdev));
-	list_for_each_safe(lst, nxt, &device->ccw_queue) {
-		cqr = list_entry(lst, struct dasd_ccw_req, list);
-		/* we are looking for two kinds or requests */
-		/* first kind: our SNSS request: */
-		if (cqr == eer->cqr) {
-			if (cqr->status == DASD_CQR_IN_IO)
-				device->discipline->term_IO(cqr);
-			list_del(&cqr->list);
-			break;
-		}
-		/* second kind: ERP requests for our SNSS request */
-		if (cqr->refers) {
-			/* If this erp request chain ends in our cqr, then */
-                        /* cal the erp_postaction to clean it up  */
-			erpcqr = cqr;
-			while (erpcqr->refers) {
-				erpcqr = erpcqr->refers;
-			}
-			if (erpcqr == eer->cqr) {
-				erp_fn = device->discipline->erp_postaction(
-					 cqr);
-				erp_fn(cqr);
-			}
-			continue;
-		}
-	}
-	spin_unlock_irq(get_ccwdev_lock(device->cdev));
-}
-
-/*
- * This function dismantles a struct dasd_eer that was created by
- * dasd_eer_probe. Since we want to free our private data structure,
- * we must make sure that the memory is not in use anymore.
- * We have to flush the work queue and remove a possible SNSS request
- * from the dasd queue.
- */
-static void
-dasd_eer_destroy(struct dasd_device *device, struct dasd_eer_private *eer)
-{
-	flush_workqueue(dasd_eer_workqueue);
-	dasd_eer_dequeue_SNSS_request(device, eer);
-	dasd_kfree_request(eer->cqr, device);
-	kfree(eer);
-};
-
-/*
- * enable the extended error reporting for a particular device
- */
-static int
-dasd_eer_enable_on_device(struct dasd_device *device)
-{
-	void *eer;
-	if (!device)
-		return -ENODEV;
-	if (device->eer)
-		return 0;
-	if (!try_module_get(THIS_MODULE)) {
-		return -EINVAL;
-	}
-	eer = (void *)dasd_eer_probe(device);
-	if (IS_ERR(eer)) {
-		module_put(THIS_MODULE);
-		return PTR_ERR(eer);
-	}
-	device->eer = eer;
-	return 0;
-}
-
-/*
- * enable the extended error reporting for a particular device
- */
-static int
-dasd_eer_disable_on_device(struct dasd_device *device)
-{
-	struct dasd_eer_private *eer = device->eer;
-
-	if (!device)
-		return -ENODEV;
-	if (!device->eer)
-		return 0;
-	device->eer = NULL;
-	dasd_eer_destroy(device,eer);
-	module_put(THIS_MODULE);
-
-	return 0;
-}
-
-/*
- * Set extended error reporting (eer)
- * Note: This will be registered as a DASD ioctl, to be called on DASD devices.
- */
-static int
-dasd_ioctl_set_eer(struct block_device *bdev, int no, long args)
-{
-	struct dasd_device *device;
-	int intval;
-
-	if (!capable(CAP_SYS_ADMIN))
-		return -EACCES;
-	if (bdev != bdev->bd_contains)
-		/* Error-reporting is not allowed for partitions */
-		return -EINVAL;
-	if (get_user(intval, (int __user *) args))
-		return -EFAULT;
-	device =  bdev->bd_disk->private_data;
-	if (device == NULL)
-		return -ENODEV;
-
-	intval = (intval != 0);
-	DEV_MESSAGE (KERN_DEBUG, device,
-		     "set eer on device to %d", intval);
-	if (intval)
-		return dasd_eer_enable_on_device(device);
-	else
-		return dasd_eer_disable_on_device(device);
-}
-
-/*
- * Get value of extended error reporting.
- * Note: This will be registered as a DASD ioctl, to be called on DASD devices.
- */
-static int
-dasd_ioctl_get_eer(struct block_device *bdev, int no, long args)
-{
-	struct dasd_device *device;
-
-	device =  bdev->bd_disk->private_data;
-	if (device == NULL)
-		return -ENODEV;
-	return put_user((device->eer != NULL), (int __user *) args);
-}
-
-/*
- * The following function can be used for those triggers that have
- * all necessary data available when the function is called.
- * If the parameter cqr is not NULL, the chain of requests will be searched
- * for valid sense data, and all valid sense data sets will be added to
- * the triggers data.
- */
-static int
-dasd_eer_write_standard_trigger(int trigger, struct dasd_device *device,
-				struct dasd_ccw_req *cqr)
-{
-	struct dasd_ccw_req *temp_cqr;
-	int data_size;
-	struct timeval tv;
-	struct dasd_eer_header header;
-	unsigned long flags;
-	struct eerbuffer *eerb;
-
-	/* go through cqr chain and count the valid sense data sets */
-	temp_cqr = cqr;
-	data_size = 0;
-	while (temp_cqr) {
-		if (temp_cqr->irb.esw.esw0.erw.cons)
-			data_size += 32;
-		temp_cqr = temp_cqr->refers;
-	}
-
-	header.total_size = sizeof(header) + data_size + 4; /* "EOR" */
-	header.trigger = trigger;
-	do_gettimeofday(&tv);
-	header.tv_sec = tv.tv_sec;
-	header.tv_usec = tv.tv_usec;
-	strncpy(header.busid, device->cdev->dev.bus_id, DASD_EER_BUSID_SIZE);
-
-	spin_lock_irqsave(&bufferlock, flags);
-	list_for_each_entry(eerb, &bufferlist, list) {
-		dasd_eer_start_record(eerb, header.total_size);
-		dasd_eer_write_buffer(eerb, sizeof(header), (char*)(&header));
-		temp_cqr = cqr;
-		while (temp_cqr) {
-			if (temp_cqr->irb.esw.esw0.erw.cons)
-				dasd_eer_write_buffer(eerb, 32, cqr->irb.ecw);
-			temp_cqr = temp_cqr->refers;
-		}
-		dasd_eer_write_buffer(eerb, 4,"EOR");
-	}
-	spin_unlock_irqrestore(&bufferlock, flags);
-
-	wake_up_interruptible(&dasd_eer_read_wait_queue);
-
-	return 0;
-}
-
-/*
- * This function writes a DASD_EER_STATECHANGE trigger.
- */
-static void
-dasd_eer_write_SNSS_trigger(struct dasd_device *device,
-			    struct dasd_ccw_req *cqr)
-{
-	int data_size;
-	int snss_rc;
-	struct timeval tv;
-	struct dasd_eer_header header;
-	unsigned long flags;
-	struct eerbuffer *eerb;
-
-	snss_rc = (cqr->status == DASD_CQR_FAILED) ? -EIO : 0;
-	if (snss_rc)
-		data_size = 0;
-	else
-		data_size = SNSS_DATA_SIZE;
-
-	header.total_size = sizeof(header) + data_size + 4; /* "EOR" */
-	header.trigger = DASD_EER_STATECHANGE;
-	do_gettimeofday(&tv);
-	header.tv_sec = tv.tv_sec;
-	header.tv_usec = tv.tv_usec;
-	strncpy(header.busid, device->cdev->dev.bus_id, DASD_EER_BUSID_SIZE);
-
-	spin_lock_irqsave(&bufferlock, flags);
-	list_for_each_entry(eerb, &bufferlist, list) {
-		dasd_eer_start_record(eerb, header.total_size);
-		dasd_eer_write_buffer(eerb, sizeof(header),(char*)(&header));
-		if (!snss_rc)
-			dasd_eer_write_buffer(eerb, SNSS_DATA_SIZE, cqr->data);
-		dasd_eer_write_buffer(eerb, 4,"EOR");
-	}
-	spin_unlock_irqrestore(&bufferlock, flags);
-
-	wake_up_interruptible(&dasd_eer_read_wait_queue);
-}
-
-/*
- * callback function for use with SNSS request
- */
-static void
-dasd_eer_SNSS_cb(struct dasd_ccw_req *cqr, void *data)
-{
-        struct dasd_device *device;
-	struct dasd_eer_private *private;
-	unsigned long irqflags;
-
-        device = (struct dasd_device *)data;
-	private = (struct dasd_eer_private *)device->eer;
-	dasd_eer_write_SNSS_trigger(device, cqr);
-	spin_lock_irqsave(&snsslock, irqflags);
-	if(!test_and_clear_bit(SNSS_REQUESTED, &private->flags)) {
-		clear_bit(CQR_IN_USE, &private->flags);
-		spin_unlock_irqrestore(&snsslock, irqflags);
-		return;
-	};
-	clear_bit(CQR_IN_USE, &private->flags);
-	spin_unlock_irqrestore(&snsslock, irqflags);
-	dasd_eer_sense_subsystem_status(device);
-	return;
-}
-
-/*
- * clean a used cqr before using it again
- */
-static void
-dasd_eer_clean_SNSS_request(struct dasd_ccw_req *cqr)
-{
-	struct ccw1 *cpaddr = cqr->cpaddr;
-	void *data = cqr->data;
-
-	memset(cqr, 0, sizeof(struct dasd_ccw_req));
-	memset(cpaddr, 0, sizeof(struct ccw1));
-	memset(data, 0, SNSS_DATA_SIZE);
-	cqr->cpaddr = cpaddr;
-	cqr->data = data;
-	strncpy((char *) &cqr->magic, "ECKD", 4);
-	ASCEBC((char *) &cqr->magic, 4);
-	set_bit(DASD_CQR_FLAGS_USE_ERP, &cqr->flags);
-}
-
-/*
- * build and start an SNSS request
- * This function is called from a work queue so we have to
- * pass the dasd_device pointer as a void pointer.
- */
-static void
-dasd_eer_sense_subsystem_status(void *data)
-{
-	struct dasd_device *device;
-	struct dasd_eer_private *private;
-	struct dasd_ccw_req *cqr;
-	struct ccw1 *ccw;
-	unsigned long irqflags;
-
-	device = (struct dasd_device *)data;
-	private = (struct dasd_eer_private *)device->eer;
-	if (!private) /* device not eer enabled any more */
-		return;
-	cqr = private->cqr;
-	spin_lock_irqsave(&snsslock, irqflags);
-	if(test_and_set_bit(CQR_IN_USE, &private->flags)) {
-		set_bit(SNSS_REQUESTED, &private->flags);
-		spin_unlock_irqrestore(&snsslock, irqflags);
-		return;
-	};
-	spin_unlock_irqrestore(&snsslock, irqflags);
-	dasd_eer_clean_SNSS_request(cqr);
-	cqr->device = device;
-	cqr->retries = 255;
-	cqr->expires = 10 * HZ;
-
-	ccw = cqr->cpaddr;
-	ccw->cmd_code = DASD_ECKD_CCW_SNSS;
-	ccw->count = SNSS_DATA_SIZE;
-	ccw->flags = 0;
-	ccw->cda = (__u32)(addr_t)cqr->data;
-
-	cqr->buildclk = get_clock();
-	cqr->status = DASD_CQR_FILLED;
-	cqr->callback = dasd_eer_SNSS_cb;
-	cqr->callback_data = (void *)device;
-        dasd_add_request_head(cqr);
-
-	return;
-}
-
-/*
- * This function is called for all triggers. It calls the appropriate
- * function that writes the actual trigger records.
- */
-static int
-dasd_eer_write_trigger(struct dasd_eer_trigger *trigger)
-{
-	int rc;
-	struct dasd_eer_private *private = trigger->device->eer;
-
-	switch (trigger->id) {
-	case DASD_EER_FATALERROR:
-	case DASD_EER_PPRCSUSPEND:
-		rc = dasd_eer_write_standard_trigger(
-			trigger->id, trigger->device, trigger->cqr);
-		break;
-	case DASD_EER_NOPATH:
-		rc = dasd_eer_write_standard_trigger(
-			trigger->id, trigger->device, NULL);
-		break;
-	case DASD_EER_STATECHANGE:
-                if (queue_work(dasd_eer_workqueue, &private->worker)) {
-                        rc=0;
-                } else {
-                        /* If the work_struct was already queued, it can't
-                         * be queued again. But this is OK since we don't
-                         * need to have it queued twice.
-                         */
-                        rc = -EBUSY;
-                }
-		break;
-	default: /* unknown trigger, so we write it without any sense data */
-		rc = dasd_eer_write_standard_trigger(
-			trigger->id, trigger->device, NULL);
-		break;
-	}
-	return rc;
-}
-
-/*
- * This function is registered with the dasd device driver and gets called
- * for all dasd eer notifications.
- */
-static int dasd_eer_notify(struct notifier_block *self,
-			    unsigned long action, void *data)
-{
-	switch (action) {
-	case DASD_EER_DISABLE:
-		dasd_eer_disable_on_device((struct dasd_device *)data);
-		break;
-	case DASD_EER_TRIGGER:
-		dasd_eer_write_trigger((struct dasd_eer_trigger *)data);
-		break;
-	}
-	return NOTIFY_OK;
-}
-
-
-/*****************************************************************************/
-/*      the device operations                                                */
-/*****************************************************************************/
-
-/*
- * On the one side we need a lock to access our internal buffer, on the
- * other side a copy_to_user can sleep. So we need to copy the data we have
- * to transfer in a readbuffer, which is protected by the readbuffer_mutex.
- */
-static char readbuffer[PAGE_SIZE];
-DECLARE_MUTEX(readbuffer_mutex);
-
-
-static int
-dasd_eer_open(struct inode *inp, struct file *filp)
-{
-	struct eerbuffer *eerb;
-	unsigned long flags;
-
-	eerb = kmalloc(sizeof(struct eerbuffer), GFP_KERNEL);
-	eerb->head = 0;
-	eerb->tail = 0;
-	eerb->residual = 0;
-	eerb->buffer_page_count = 1;
-	eerb->buffersize = eerb->buffer_page_count * PAGE_SIZE;
-        eerb->buffer = kmalloc(eerb->buffer_page_count*sizeof(char*),
-			       GFP_KERNEL);
-        if (!eerb->buffer)
-                return -ENOMEM;
-	if (dasd_eer_allocate_buffer_pages(eerb->buffer,
-					   eerb->buffer_page_count)) {
-		kfree(eerb->buffer);
-		return -ENOMEM;
-	}
-	filp->private_data = eerb;
-	spin_lock_irqsave(&bufferlock, flags);
-	list_add(&eerb->list, &bufferlist);
-	spin_unlock_irqrestore(&bufferlock, flags);
-
-	return nonseekable_open(inp,filp);
-}
-
-static int
-dasd_eer_close(struct inode *inp, struct file *filp)
-{
-	struct eerbuffer *eerb;
-	unsigned long flags;
-
-	eerb = (struct eerbuffer *)filp->private_data;
-	spin_lock_irqsave(&bufferlock, flags);
-	list_del(&eerb->list);
-	spin_unlock_irqrestore(&bufferlock, flags);
-	dasd_eer_free_buffer_pages(eerb->buffer, eerb->buffer_page_count);
-	kfree(eerb->buffer);
-	kfree(eerb);
-
-	return 0;
-}
-
-static long
-dasd_eer_ioctl(struct file *filp, unsigned int cmd, unsigned long arg)
-{
-	int intval;
-	struct eerbuffer *eerb;
-
-	eerb = (struct eerbuffer *)filp->private_data;
-	switch (cmd) {
-	case DASD_EER_PURGE:
-		dasd_eer_purge_buffer(eerb);
-		return 0;
-	case DASD_EER_SETBUFSIZE:
-		if (get_user(intval, (int __user *)arg))
-			return -EFAULT;
-		return dasd_eer_resize_buffer(eerb, intval);
-	default:
-		return -ENOIOCTLCMD;
-	}
-}
-
-static ssize_t
-dasd_eer_read(struct file *filp, char __user *buf, size_t count, loff_t *ppos)
-{
-	int tc,rc;
-	int tailcount,effective_count;
-        unsigned long flags;
-	struct eerbuffer *eerb;
-
-	eerb = (struct eerbuffer *)filp->private_data;
-	if(down_interruptible(&readbuffer_mutex))
-		return -ERESTARTSYS;
-
-	spin_lock_irqsave(&bufferlock, flags);
-
-	if (eerb->residual < 0) { /* the remainder of this record */
-		                  /* has been deleted             */
-		eerb->residual = 0;
-		spin_unlock_irqrestore(&bufferlock, flags);
-		up(&readbuffer_mutex);
-		return -EIO;
-	} else if (eerb->residual > 0) {
-		/* OK we still have a second half of a record to deliver */
-		effective_count = min(eerb->residual, (int)count);
-		eerb->residual -= effective_count;
-	} else {
-		tc = 0;
-		while (!tc) {
-			tc = dasd_eer_read_buffer(eerb,
-				sizeof(tailcount), (char*)(&tailcount));
-			if (!tc) {
-				/* no data available */
-				spin_unlock_irqrestore(&bufferlock, flags);
-				up(&readbuffer_mutex);
-				if (filp->f_flags & O_NONBLOCK)
-					return -EAGAIN;
-				rc = wait_event_interruptible(
-					dasd_eer_read_wait_queue,
-					eerb->head != eerb->tail);
-				if (rc) {
-					return rc;
-				}
-				if(down_interruptible(&readbuffer_mutex))
-					return -ERESTARTSYS;
-				spin_lock_irqsave(&bufferlock, flags);
-			}
-		}
-		WARN_ON(tc != sizeof(tailcount));
-		effective_count = min(tailcount,(int)count);
-		eerb->residual = tailcount - effective_count;
-	}
-
-	tc = dasd_eer_read_buffer(eerb, effective_count, readbuffer);
-	WARN_ON(tc != effective_count);
-
-	spin_unlock_irqrestore(&bufferlock, flags);
-
-	if (copy_to_user(buf, readbuffer, effective_count)) {
-		up(&readbuffer_mutex);
-		return -EFAULT;
-	}
-
-	up(&readbuffer_mutex);
-	return effective_count;
-}
-
-static unsigned int
-dasd_eer_poll (struct file *filp, poll_table *ptable)
-{
-	unsigned int mask;
-	unsigned long flags;
-	struct eerbuffer *eerb;
-
-	eerb = (struct eerbuffer *)filp->private_data;
-	poll_wait(filp, &dasd_eer_read_wait_queue, ptable);
-	spin_lock_irqsave(&bufferlock, flags);
-	if (eerb->head != eerb->tail)
-		mask = POLLIN | POLLRDNORM ;
-	else
-		mask = 0;
-	spin_unlock_irqrestore(&bufferlock, flags);
-	return mask;
-}
-
-static struct file_operations dasd_eer_fops = {
-	.open		= &dasd_eer_open,
-	.release	= &dasd_eer_close,
-	.unlocked_ioctl = &dasd_eer_ioctl,
-	.compat_ioctl	= &dasd_eer_ioctl,
-	.read		= &dasd_eer_read,
-	.poll		= &dasd_eer_poll,
-	.owner		= THIS_MODULE,
-};
-
-static struct miscdevice dasd_eer_dev = {
-	.minor	    = MISC_DYNAMIC_MINOR,
-	.name	    = "dasd_eer",
-	.fops	    = &dasd_eer_fops,
-};
-
-
-/*****************************************************************************/
-/*	Init and exit							     */
-/*****************************************************************************/
-
-static int
-__init dasd_eer_init(void)
-{
-	int rc;
-
-	dasd_eer_workqueue = create_singlethread_workqueue("dasd_eer");
-	if (!dasd_eer_workqueue) {
-		MESSAGE(KERN_ERR , "%s", "dasd_eer_init could not "
-		       "create workqueue \n");
-		rc = -ENOMEM;
-		goto out;
-	}
-
-	rc = dasd_register_eer_notifier(&dasd_eer_nb);
-	if (rc) {
-		MESSAGE(KERN_ERR, "%s", "dasd_eer_init could not "
-		       "register error reporting");
-		goto queue;
-	}
-
-	dasd_ioctl_no_register(THIS_MODULE, BIODASDEERSET, dasd_ioctl_set_eer);
-	dasd_ioctl_no_register(THIS_MODULE, BIODASDEERGET, dasd_ioctl_get_eer);
-
-	/* we don't need our own character device,
-	 * so we just register as misc device */
-	rc = misc_register(&dasd_eer_dev);
-	if (rc) {
-		MESSAGE(KERN_ERR, "%s", "dasd_eer_init could not "
-		       "register misc device");
-		goto unregister;
-	}
-
-	return 0;
-
-unregister:
-	dasd_unregister_eer_notifier(&dasd_eer_nb);
-	dasd_ioctl_no_unregister(THIS_MODULE, BIODASDEERSET,
-				 dasd_ioctl_set_eer);
-	dasd_ioctl_no_unregister(THIS_MODULE, BIODASDEERGET,
-				 dasd_ioctl_get_eer);
-queue:
-	destroy_workqueue(dasd_eer_workqueue);
-out:
-	return rc;
-
-}
-module_init(dasd_eer_init);
-
-static void
-__exit dasd_eer_exit(void)
-{
-	dasd_unregister_eer_notifier(&dasd_eer_nb);
-	dasd_ioctl_no_unregister(THIS_MODULE, BIODASDEERSET,
-				 dasd_ioctl_set_eer);
-	dasd_ioctl_no_unregister(THIS_MODULE, BIODASDEERGET,
-				 dasd_ioctl_get_eer);
-	destroy_workqueue(dasd_eer_workqueue);
-
-	WARN_ON(misc_deregister(&dasd_eer_dev) != 0);
-}
-module_exit(dasd_eer_exit);
diff --git a/drivers/s390/block/dasd_int.h b/drivers/s390/block/dasd_int.h
index d1b08fa13fd..0592354cc60 100644
--- a/drivers/s390/block/dasd_int.h
+++ b/drivers/s390/block/dasd_int.h
@@ -275,34 +275,6 @@ struct dasd_discipline {
 
 extern struct dasd_discipline *dasd_diag_discipline_pointer;
 
-
-/*
- * Notification numbers for extended error reporting notifications:
- * The DASD_EER_DISABLE notification is sent before a dasd_device (and it's
- * eer pointer) is freed. The error reporting module needs to do all necessary
- * cleanup steps.
- * The DASD_EER_TRIGGER notification sends the actual error reports (triggers).
- */
-#define DASD_EER_DISABLE 0
-#define DASD_EER_TRIGGER 1
-
-/* Trigger IDs for extended error reporting DASD_EER_TRIGGER notification */
-#define DASD_EER_FATALERROR  1
-#define DASD_EER_NOPATH      2
-#define DASD_EER_STATECHANGE 3
-#define DASD_EER_PPRCSUSPEND 4
-
-/*
- * The dasd_eer_trigger structure contains all data that we need to send
- * along with an DASD_EER_TRIGGER notification.
- */
-struct dasd_eer_trigger {
-	unsigned int id;
-	struct dasd_device *device;
-	struct dasd_ccw_req *cqr;
-};
-
-
 struct dasd_device {
 	/* Block device stuff. */
 	struct gendisk *gdp;
@@ -316,11 +288,9 @@ struct dasd_device {
 	unsigned long flags;		/* per device flags */
 	unsigned short features;        /* copy of devmap-features (read-only!) */
 
-	/* extended error reporting stuff (eer) */
-	void *eer;
-
 	/* Device discipline stuff. */
 	struct dasd_discipline *discipline;
+	struct dasd_discipline *base_discipline;
 	char *private;
 
 	/* Device state and target state. */
@@ -519,12 +489,6 @@ int dasd_generic_set_online(struct ccw_device *, struct dasd_discipline *);
 int dasd_generic_set_offline (struct ccw_device *cdev);
 int dasd_generic_notify(struct ccw_device *, int);
 void dasd_generic_auto_online (struct ccw_driver *);
-int dasd_register_eer_notifier(struct notifier_block *);
-int dasd_unregister_eer_notifier(struct notifier_block *);
-void dasd_write_eer_trigger(unsigned int , struct dasd_device *,
-			struct dasd_ccw_req *);
-
-
 
 /* externals in dasd_devmap.c */
 extern int dasd_max_devindex;
diff --git a/drivers/s390/cio/device.c b/drivers/s390/cio/device.c
index 062fb100d94..afc4e88551a 100644
--- a/drivers/s390/cio/device.c
+++ b/drivers/s390/cio/device.c
@@ -359,7 +359,7 @@ ccw_device_set_online(struct ccw_device *cdev)
 	else 
 		pr_debug("ccw_device_offline returned %d, device %s\n",
 			 ret, cdev->dev.bus_id);
-	return (ret = 0) ? -ENODEV : ret;
+	return (ret == 0) ? -ENODEV : ret;
 }
 
 static ssize_t
diff --git a/drivers/s390/cio/device_pgid.c b/drivers/s390/cio/device_pgid.c
index d2a5b04d7cb..85b1020a1fc 100644
--- a/drivers/s390/cio/device_pgid.c
+++ b/drivers/s390/cio/device_pgid.c
@@ -405,7 +405,7 @@ __ccw_device_disband_start(struct ccw_device *cdev)
 		cdev->private->iretry = 5;
 		cdev->private->imask >>= 1;
 	}
-	ccw_device_verify_done(cdev, (sch->lpm != 0) ? 0 : -ENODEV);
+	ccw_device_disband_done(cdev, (sch->lpm != 0) ? 0 : -ENODEV);
 }
 
 /*
diff --git a/drivers/s390/cio/device_status.c b/drivers/s390/cio/device_status.c
index dad4dd9887c..6c762b43f92 100644
--- a/drivers/s390/cio/device_status.c
+++ b/drivers/s390/cio/device_status.c
@@ -317,7 +317,6 @@ ccw_device_do_sense(struct ccw_device *cdev, struct irb *irb)
 	/*
 	 * We have ending status but no sense information. Do a basic sense.
 	 */
-	sch = to_subchannel(cdev->dev.parent);
 	sch->sense_ccw.cmd_code = CCW_CMD_BASIC_SENSE;
 	sch->sense_ccw.cda = (__u32) __pa(cdev->private->irb.ecw);
 	sch->sense_ccw.count = SENSE_MAX_COUNT;
diff --git a/drivers/s390/cio/qdio.c b/drivers/s390/cio/qdio.c
index 45ce032772f..9ed37dc9a1b 100644
--- a/drivers/s390/cio/qdio.c
+++ b/drivers/s390/cio/qdio.c
@@ -165,8 +165,13 @@ qdio_do_eqbs(struct qdio_q *q, unsigned char *state,
 	q_no = q->q_no;
 	if(!q->is_input_q)
 		q_no += irq->no_input_qs;
+again:
 	ccq = do_eqbs(irq->sch_token, state, q_no, start, cnt);
 	rc = qdio_check_ccq(q, ccq);
+	if (rc == 1) {
+		QDIO_DBF_TEXT5(1,trace,"eqAGAIN");
+		goto again;
+	}
 	if (rc < 0) {
                 QDIO_DBF_TEXT2(1,trace,"eqberr");
                 sprintf(dbf_text,"%2x,%2x,%d,%d",tmp_cnt, *cnt, ccq, q_no);
@@ -195,8 +200,13 @@ qdio_do_sqbs(struct qdio_q *q, unsigned char state,
 	q_no = q->q_no;
 	if(!q->is_input_q)
 		q_no += irq->no_input_qs;
+again:
 	ccq = do_sqbs(irq->sch_token, state, q_no, start, cnt);
 	rc = qdio_check_ccq(q, ccq);
+	if (rc == 1) {
+		QDIO_DBF_TEXT5(1,trace,"sqAGAIN");
+		goto again;
+	}
 	if (rc < 0) {
                 QDIO_DBF_TEXT3(1,trace,"sqberr");
                 sprintf(dbf_text,"%2x,%2x,%d,%d",tmp_cnt,*cnt,ccq,q_no);
@@ -1187,8 +1197,7 @@ tiqdio_is_inbound_q_done(struct qdio_q *q)
 
 	if (!no_used)
 		return 1;
-
-	if (!q->siga_sync)
+	if (!q->siga_sync && !irq->is_qebsm)
 		/* we'll check for more primed buffers in qeth_stop_polling */
 		return 0;
 	if (irq->is_qebsm) {
diff --git a/drivers/s390/net/lcs.c b/drivers/s390/net/lcs.c
index 6229ba4995a..9cf88d7201d 100644
--- a/drivers/s390/net/lcs.c
+++ b/drivers/s390/net/lcs.c
@@ -98,9 +98,9 @@ lcs_register_debug_facility(void)
 		return -ENOMEM;
 	}
 	debug_register_view(lcs_dbf_setup, &debug_hex_ascii_view);
-	debug_set_level(lcs_dbf_setup, 4);
+	debug_set_level(lcs_dbf_setup, 2);
 	debug_register_view(lcs_dbf_trace, &debug_hex_ascii_view);
-	debug_set_level(lcs_dbf_trace, 4);
+	debug_set_level(lcs_dbf_trace, 2);
 	return 0;
 }
 
@@ -1292,9 +1292,8 @@ lcs_set_multicast_list(struct net_device *dev)
         LCS_DBF_TEXT(4, trace, "setmulti");
         card = (struct lcs_card *) dev->priv;
 
-        if (!lcs_set_thread_start_bit(card, LCS_SET_MC_THREAD)) {
+        if (!lcs_set_thread_start_bit(card, LCS_SET_MC_THREAD)) 
 		schedule_work(&card->kernel_thread_starter);
-	}
 }
 
 #endif /* CONFIG_IP_MULTICAST */
@@ -1459,6 +1458,8 @@ lcs_txbuffer_cb(struct lcs_channel *channel, struct lcs_buffer *buffer)
 	lcs_release_buffer(channel, buffer);
 	card = (struct lcs_card *)
 		((char *) channel - offsetof(struct lcs_card, write));
+	if (netif_queue_stopped(card->dev))
+		netif_wake_queue(card->dev);
 	spin_lock(&card->lock);
 	card->tx_emitted--;
 	if (card->tx_emitted <= 0 && card->tx_buffer != NULL)
@@ -1478,6 +1479,7 @@ __lcs_start_xmit(struct lcs_card *card, struct sk_buff *skb,
 		 struct net_device *dev)
 {
 	struct lcs_header *header;
+	int rc = 0;
 
 	LCS_DBF_TEXT(5, trace, "hardxmit");
 	if (skb == NULL) {
@@ -1492,10 +1494,8 @@ __lcs_start_xmit(struct lcs_card *card, struct sk_buff *skb,
 		card->stats.tx_carrier_errors++;
 		return 0;
 	}
-	if (netif_queue_stopped(dev) ) {
-		card->stats.tx_dropped++;
-		return -EBUSY;
-	}
+	netif_stop_queue(card->dev);
+	spin_lock(&card->lock);
 	if (card->tx_buffer != NULL &&
 	    card->tx_buffer->count + sizeof(struct lcs_header) +
 	    skb->len + sizeof(u16) > LCS_IOBUFFERSIZE)
@@ -1506,7 +1506,8 @@ __lcs_start_xmit(struct lcs_card *card, struct sk_buff *skb,
 		card->tx_buffer = lcs_get_buffer(&card->write);
 		if (card->tx_buffer == NULL) {
 			card->stats.tx_dropped++;
-			return -EBUSY;
+			rc = -EBUSY;
+			goto out;
 		}
 		card->tx_buffer->callback = lcs_txbuffer_cb;
 		card->tx_buffer->count = 0;
@@ -1518,13 +1519,18 @@ __lcs_start_xmit(struct lcs_card *card, struct sk_buff *skb,
 	header->type = card->lan_type;
 	header->slot = card->portno;
 	memcpy(header + 1, skb->data, skb->len);
+	spin_unlock(&card->lock);
 	card->stats.tx_bytes += skb->len;
 	card->stats.tx_packets++;
 	dev_kfree_skb(skb);
-	if (card->tx_emitted <= 0)
+	netif_wake_queue(card->dev);
+	spin_lock(&card->lock);
+	if (card->tx_emitted <= 0 && card->tx_buffer != NULL)
 		/* If this is the first tx buffer emit it immediately. */
 		__lcs_emit_txbuffer(card);
-	return 0;
+out:
+	spin_unlock(&card->lock);
+	return rc;
 }
 
 static int
@@ -1535,9 +1541,7 @@ lcs_start_xmit(struct sk_buff *skb, struct net_device *dev)
 
 	LCS_DBF_TEXT(5, trace, "pktxmit");
 	card = (struct lcs_card *) dev->priv;
-	spin_lock(&card->lock);
 	rc = __lcs_start_xmit(card, skb, dev);
-	spin_unlock(&card->lock);
 	return rc;
 }
 
@@ -2319,7 +2323,6 @@ __init lcs_init_module(void)
 		PRINT_ERR("Initialization failed\n");
 		return rc;
 	}
-
 	return 0;
 }
 
diff --git a/drivers/s390/net/lcs.h b/drivers/s390/net/lcs.h
index 08e60ad4391..2fad5e40c2e 100644
--- a/drivers/s390/net/lcs.h
+++ b/drivers/s390/net/lcs.h
@@ -95,7 +95,7 @@ do {                                       \
  */
 #define LCS_ILLEGAL_OFFSET		0xffff
 #define LCS_IOBUFFERSIZE		0x5000
-#define LCS_NUM_BUFFS			8	/* needs to be power of 2 */
+#define LCS_NUM_BUFFS			32	/* needs to be power of 2 */
 #define LCS_MAC_LENGTH			6
 #define LCS_INVALID_PORT_NO		-1
 #define LCS_LANCMD_TIMEOUT_DEFAULT      5
diff --git a/drivers/s390/net/qeth.h b/drivers/s390/net/qeth.h
index 9a064d4727a..4df0fcd7b10 100644
--- a/drivers/s390/net/qeth.h
+++ b/drivers/s390/net/qeth.h
@@ -1076,16 +1076,6 @@ qeth_get_qdio_q_format(struct qeth_card *card)
 }
 
 static inline int
-qeth_isdigit(char * buf)
-{
-	while (*buf) {
-		if (!isdigit(*buf++))
-			return 0;
-	}
-	return 1;
-}
-
-static inline int
 qeth_isxdigit(char * buf)
 {
 	while (*buf) {
@@ -1104,33 +1094,17 @@ qeth_ipaddr4_to_string(const __u8 *addr, char *buf)
 static inline int
 qeth_string_to_ipaddr4(const char *buf, __u8 *addr)
 {
-	const char *start, *end;
-	char abuf[4];
-	char *tmp;
-	int len;
-	int i;
-
-	start = buf;
-	for (i = 0; i < 4; i++) {
-		if (i == 3) {
-			end = strchr(start,0xa);
-			if (end)
-				len = end - start;
-			else		
-				len = strlen(start);
-		}
-		else {
-			end = strchr(start, '.');
-			len = end - start;
-		}
-		if ((len <= 0) || (len > 3))
-			return -EINVAL;
-		memset(abuf, 0, 4);
-		strncpy(abuf, start, len);
-		if (!qeth_isdigit(abuf))
+	int count = 0, rc = 0;
+	int in[4];
+
+	rc = sscanf(buf, "%d.%d.%d.%d%n", 
+		    &in[0], &in[1], &in[2], &in[3], &count);
+	if (rc != 4  || count) 
+		return -EINVAL;
+	for (count = 0; count < 4; count++) {
+		if (in[count] > 255)
 			return -EINVAL;
-		addr[i] = simple_strtoul(abuf, &tmp, 10);
-		start = end + 1;
+		addr[count] = in[count];
 	}
 	return 0;
 }
@@ -1149,36 +1123,44 @@ qeth_ipaddr6_to_string(const __u8 *addr, char *buf)
 static inline int
 qeth_string_to_ipaddr6(const char *buf, __u8 *addr)
 {
-	const char *start, *end;
-	u16 *tmp_addr;
-	char abuf[5];
-	char *tmp;
-	int len;
-	int i;
-
-	tmp_addr = (u16 *)addr;
-	start = buf;
-	for (i = 0; i < 8; i++) {
-		if (i == 7) {
-			end = strchr(start,0xa);
-			if (end)
-				len = end - start;
-			else
-				len = strlen(start);
-		}
-		else {
-			end = strchr(start, ':');
-			len = end - start;
+	char *end, *start;
+	__u16 *in;
+        char num[5];
+        int num2, cnt, out, found, save_cnt;
+        unsigned short in_tmp[8] = {0, };
+
+	cnt = out = found = save_cnt = num2 = 0;
+        end = start = (char *) buf;
+	in = (__u16 *) addr;	
+	memset(in, 0, 16);
+        while (end) {
+                end = strchr(end,':');
+                if (end == NULL) {
+                        end = (char *)buf + (strlen(buf));
+                        out = 1;
+                }
+                if ((end - start)) { 
+                        memset(num, 0, 5);
+                        memcpy(num, start, end - start);
+			if (!qeth_isxdigit(num))
+				return -EINVAL;
+                        sscanf(start, "%x", &num2);
+                        if (found)
+                                in_tmp[save_cnt++] = num2;
+                        else
+                                in[cnt++] = num2;
+                        if (out)
+                                break;
+                } else {
+			if (found)
+				return -EINVAL;
+                        found = 1;
 		}
-		if ((len <= 0) || (len > 4))
-			return -EINVAL;
-		memset(abuf, 0, 5);
-		strncpy(abuf, start, len);
-		if (!qeth_isxdigit(abuf))
-			return -EINVAL;
-		tmp_addr[i] = simple_strtoul(abuf, &tmp, 16);
-		start = end + 1;
-	}
+		start = ++end;
+        }
+        cnt = 7;
+	while (save_cnt)
+                in[cnt--] = in_tmp[--save_cnt];
 	return 0;
 }
 
diff --git a/drivers/s390/net/qeth_eddp.c b/drivers/s390/net/qeth_eddp.c
index b0231312778..82cb4af2f0e 100644
--- a/drivers/s390/net/qeth_eddp.c
+++ b/drivers/s390/net/qeth_eddp.c
@@ -59,8 +59,7 @@ qeth_eddp_free_context(struct qeth_eddp_context *ctx)
 	for (i = 0; i < ctx->num_pages; ++i)
 		free_page((unsigned long)ctx->pages[i]);
 	kfree(ctx->pages);
-	if (ctx->elements != NULL)
-		kfree(ctx->elements);
+	kfree(ctx->elements);
 	kfree(ctx);
 }
 
@@ -413,6 +412,13 @@ __qeth_eddp_fill_context_tcp(struct qeth_eddp_context *ctx,
 	
 	QETH_DBF_TEXT(trace, 5, "eddpftcp");
 	eddp->skb_offset = sizeof(struct qeth_hdr) + eddp->nhl + eddp->thl;
+       if (eddp->qh.hdr.l2.id == QETH_HEADER_TYPE_LAYER2) {
+               eddp->skb_offset += sizeof(struct ethhdr);
+#ifdef CONFIG_QETH_VLAN
+               if (eddp->mac.h_proto == __constant_htons(ETH_P_8021Q))
+                       eddp->skb_offset += VLAN_HLEN;
+#endif /* CONFIG_QETH_VLAN */
+       }
 	tcph = eddp->skb->h.th;
 	while (eddp->skb_offset < eddp->skb->len) {
 		data_len = min((int)skb_shinfo(eddp->skb)->tso_size,
@@ -483,6 +489,7 @@ qeth_eddp_fill_context_tcp(struct qeth_eddp_context *ctx,
 		return -ENOMEM;
 	}
 	if (qhdr->hdr.l2.id == QETH_HEADER_TYPE_LAYER2) {
+		skb->mac.raw = (skb->data) + sizeof(struct qeth_hdr);
 		memcpy(&eddp->mac, eth_hdr(skb), ETH_HLEN);
 #ifdef CONFIG_QETH_VLAN
 		if (eddp->mac.h_proto == __constant_htons(ETH_P_8021Q)) {
diff --git a/drivers/s390/net/qeth_main.c b/drivers/s390/net/qeth_main.c
index 410abeada6c..dba7f7f02e7 100644
--- a/drivers/s390/net/qeth_main.c
+++ b/drivers/s390/net/qeth_main.c
@@ -516,7 +516,8 @@ __qeth_set_offline(struct ccwgroup_device *cgdev, int recovery_mode)
 	QETH_DBF_TEXT(setup, 3, "setoffl");
 	QETH_DBF_HEX(setup, 3, &card, sizeof(void *));
 	
-	netif_carrier_off(card->dev);
+	if (card->dev && netif_carrier_ok(card->dev))
+		netif_carrier_off(card->dev);
 	recover_flag = card->state;
 	if (qeth_stop_card(card, recovery_mode) == -ERESTARTSYS){
 		PRINT_WARN("Stopping card %s interrupted by user!\n",
@@ -1679,6 +1680,7 @@ qeth_cmd_timeout(unsigned long data)
 	spin_unlock_irqrestore(&reply->card->lock, flags);
 }
 
+
 static struct qeth_ipa_cmd *
 qeth_check_ipa_data(struct qeth_card *card, struct qeth_cmd_buffer *iob)
 {
@@ -1699,7 +1701,8 @@ qeth_check_ipa_data(struct qeth_card *card, struct qeth_cmd_buffer *iob)
 					   QETH_CARD_IFNAME(card),
 					   card->info.chpid);
 				card->lan_online = 0;
-				netif_carrier_off(card->dev);
+				if (card->dev && netif_carrier_ok(card->dev))
+					netif_carrier_off(card->dev);
 				return NULL;
 			case IPA_CMD_STARTLAN:
 				PRINT_INFO("Link reestablished on %s "
@@ -5562,7 +5565,7 @@ qeth_set_multicast_list(struct net_device *dev)
 	if (card->info.type == QETH_CARD_TYPE_OSN)
 		return ;
 	 
-	QETH_DBF_TEXT(trace,3,"setmulti");
+	QETH_DBF_TEXT(trace, 3, "setmulti");
 	qeth_delete_mc_addresses(card);
 	if (card->options.layer2) {
 		qeth_layer2_add_multicast(card);
@@ -5579,7 +5582,6 @@ out:
 		return;
 	if (qeth_set_thread_start_bit(card, QETH_SET_PROMISC_MODE_THREAD)==0)
 		schedule_work(&card->kernel_thread_starter);
-
 }
 
 static int
@@ -7452,6 +7454,7 @@ qeth_softsetup_card(struct qeth_card *card)
 		card->lan_online = 1;
 	if (card->info.type==QETH_CARD_TYPE_OSN)
 		goto out;
+	qeth_set_large_send(card, card->options.large_send);
 	if (card->options.layer2) {
 		card->dev->features |=
 			NETIF_F_HW_VLAN_FILTER |
@@ -7468,12 +7471,6 @@ qeth_softsetup_card(struct qeth_card *card)
 #endif
 		goto out;
 	}
-	if ((card->options.large_send == QETH_LARGE_SEND_EDDP) ||
-	    (card->options.large_send == QETH_LARGE_SEND_TSO))
-		card->dev->features |= NETIF_F_TSO | NETIF_F_SG;
-	else
-		card->dev->features &= ~(NETIF_F_TSO | NETIF_F_SG);
-
 	if ((rc = qeth_setadapter_parms(card)))
 		QETH_DBF_TEXT_(setup, 2, "2err%d", rc);
 	if ((rc = qeth_start_ipassists(card)))
diff --git a/drivers/scsi/esp.c b/drivers/scsi/esp.c
index f6900538be9..87a8c3d2072 100644
--- a/drivers/scsi/esp.c
+++ b/drivers/scsi/esp.c
@@ -2068,14 +2068,12 @@ static int esp_reset(struct scsi_cmnd *SCptr)
 {
 	struct esp *esp = (struct esp *) SCptr->device->host->hostdata;
 
+	spin_lock_irq(esp->ehost->host_lock);
 	(void) esp_do_resetbus(esp);
-
 	spin_unlock_irq(esp->ehost->host_lock);
 
 	wait_event(esp->reset_queue, (esp->resetting_bus == 0));
 
-	spin_lock_irq(esp->ehost->host_lock);
-
 	return SUCCESS;
 }
 
diff --git a/drivers/scsi/libata-core.c b/drivers/scsi/libata-core.c
index 46c4cdbaee8..5f1d7580218 100644
--- a/drivers/scsi/libata-core.c
+++ b/drivers/scsi/libata-core.c
@@ -614,7 +614,7 @@ int ata_rwcmd_protocol(struct ata_queued_cmd *qc)
 	} else if (lba48 && (qc->ap->flags & ATA_FLAG_PIO_LBA48)) {
 		/* Unable to use DMA due to host limitation */
 		tf->protocol = ATA_PROT_PIO;
-		index = dev->multi_count ? 0 : 4;
+		index = dev->multi_count ? 0 : 8;
 	} else {
 		tf->protocol = ATA_PROT_DMA;
 		index = 16;
@@ -2514,7 +2514,7 @@ static void ata_sg_clean(struct ata_queued_cmd *qc)
 	assert(sg != NULL);
 
 	if (qc->flags & ATA_QCFLAG_SINGLE)
-		assert(qc->n_elem == 1);
+		assert(qc->n_elem <= 1);
 
 	VPRINTK("unmapping %u sg elements\n", qc->n_elem);
 
@@ -2537,7 +2537,7 @@ static void ata_sg_clean(struct ata_queued_cmd *qc)
 			kunmap_atomic(addr, KM_IRQ0);
 		}
 	} else {
-		if (sg_dma_len(&sg[0]) > 0)
+		if (qc->n_elem)
 			dma_unmap_single(ap->host_set->dev,
 				sg_dma_address(&sg[0]), sg_dma_len(&sg[0]),
 				dir);
@@ -2570,7 +2570,7 @@ static void ata_fill_sg(struct ata_queued_cmd *qc)
 	unsigned int idx;
 
 	assert(qc->__sg != NULL);
-	assert(qc->n_elem > 0);
+	assert(qc->n_elem > 0 || qc->pad_len > 0);
 
 	idx = 0;
 	ata_for_each_sg(sg, qc) {
@@ -2715,6 +2715,7 @@ static int ata_sg_setup_one(struct ata_queued_cmd *qc)
 	int dir = qc->dma_dir;
 	struct scatterlist *sg = qc->__sg;
 	dma_addr_t dma_address;
+	int trim_sg = 0;
 
 	/* we must lengthen transfers to end on a 32-bit boundary */
 	qc->pad_len = sg->length & 3;
@@ -2734,13 +2735,15 @@ static int ata_sg_setup_one(struct ata_queued_cmd *qc)
 		sg_dma_len(psg) = ATA_DMA_PAD_SZ;
 		/* trim sg */
 		sg->length -= qc->pad_len;
+		if (sg->length == 0)
+			trim_sg = 1;
 
 		DPRINTK("padding done, sg->length=%u pad_len=%u\n",
 			sg->length, qc->pad_len);
 	}
 
-	if (!sg->length) {
-		sg_dma_address(sg) = 0;
+	if (trim_sg) {
+		qc->n_elem--;
 		goto skip_map;
 	}
 
@@ -2753,9 +2756,9 @@ static int ata_sg_setup_one(struct ata_queued_cmd *qc)
 	}
 
 	sg_dma_address(sg) = dma_address;
-skip_map:
 	sg_dma_len(sg) = sg->length;
 
+skip_map:
 	DPRINTK("mapped buffer of %d bytes for %s\n", sg_dma_len(sg),
 		qc->tf.flags & ATA_TFLAG_WRITE ? "write" : "read");
 
@@ -3357,11 +3360,12 @@ static void ata_pio_error(struct ata_port *ap)
 {
 	struct ata_queued_cmd *qc;
 
-	printk(KERN_WARNING "ata%u: PIO error\n", ap->id);
-
 	qc = ata_qc_from_tag(ap, ap->active_tag);
 	assert(qc != NULL);
 
+	if (qc->tf.command != ATA_CMD_PACKET)
+		printk(KERN_WARNING "ata%u: PIO error\n", ap->id);
+
 	/* make sure qc->err_mask is available to 
 	 * know what's wrong and recover
 	 */
diff --git a/drivers/scsi/sata_mv.c b/drivers/scsi/sata_mv.c
index 6fddf17a3b7..2770005324b 100644
--- a/drivers/scsi/sata_mv.c
+++ b/drivers/scsi/sata_mv.c
@@ -997,6 +997,7 @@ static void mv_qc_prep(struct ata_queued_cmd *qc)
 	case ATA_CMD_READ_EXT:
 	case ATA_CMD_WRITE:
 	case ATA_CMD_WRITE_EXT:
+	case ATA_CMD_WRITE_FUA_EXT:
 		mv_crqb_pack_cmd(cw++, tf->hob_nsect, ATA_REG_NSECT, 0);
 		break;
 #ifdef LIBATA_NCQ		/* FIXME: remove this line when NCQ added */
diff --git a/drivers/scsi/sata_qstor.c b/drivers/scsi/sata_qstor.c
index de05e2883f9..80480f0fb2b 100644
--- a/drivers/scsi/sata_qstor.c
+++ b/drivers/scsi/sata_qstor.c
@@ -277,7 +277,7 @@ static unsigned int qs_fill_sg(struct ata_queued_cmd *qc)
 	u8 *prd = pp->pkt + QS_CPB_BYTES;
 
 	assert(qc->__sg != NULL);
-	assert(qc->n_elem > 0);
+	assert(qc->n_elem > 0 || qc->pad_len > 0);
 
 	nelem = 0;
 	ata_for_each_sg(sg, qc) {
diff --git a/drivers/scsi/sata_sil.c b/drivers/scsi/sata_sil.c
index 17f74d3c10e..9face3c6aa2 100644
--- a/drivers/scsi/sata_sil.c
+++ b/drivers/scsi/sata_sil.c
@@ -49,11 +49,13 @@
 #define DRV_VERSION	"0.9"
 
 enum {
+	SIL_FLAG_RERR_ON_DMA_ACT = (1 << 29),
 	SIL_FLAG_MOD15WRITE	= (1 << 30),
 
 	sil_3112		= 0,
 	sil_3112_m15w		= 1,
-	sil_3114		= 2,
+	sil_3512		= 2,
+	sil_3114		= 3,
 
 	SIL_FIFO_R0		= 0x40,
 	SIL_FIFO_W0		= 0x41,
@@ -90,7 +92,7 @@ static void sil_post_set_mode (struct ata_port *ap);
 static const struct pci_device_id sil_pci_tbl[] = {
 	{ 0x1095, 0x3112, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
 	{ 0x1095, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
-	{ 0x1095, 0x3512, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
+	{ 0x1095, 0x3512, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3512 },
 	{ 0x1095, 0x3114, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3114 },
 	{ 0x1002, 0x436e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
 	{ 0x1002, 0x4379, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112_m15w },
@@ -185,7 +187,8 @@ static const struct ata_port_info sil_port_info[] = {
 		.mwdma_mask	= 0x07,			/* mwdma0-2 */
 		.udma_mask	= 0x3f,			/* udma0-5 */
 		.port_ops	= &sil_ops,
-	}, /* sil_3112_15w - keep it sync'd w/ sil_3112 */
+	},
+	/* sil_3112_15w - keep it sync'd w/ sil_3112 */
 	{
 		.sht		= &sil_sht,
 		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
@@ -195,11 +198,24 @@ static const struct ata_port_info sil_port_info[] = {
 		.mwdma_mask	= 0x07,			/* mwdma0-2 */
 		.udma_mask	= 0x3f,			/* udma0-5 */
 		.port_ops	= &sil_ops,
-	}, /* sil_3114 */
+	},
+	/* sil_3512 */
 	{
 		.sht		= &sil_sht,
 		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				  ATA_FLAG_SRST | ATA_FLAG_MMIO,
+				  ATA_FLAG_SRST | ATA_FLAG_MMIO |
+				  SIL_FLAG_RERR_ON_DMA_ACT,
+		.pio_mask	= 0x1f,			/* pio0-4 */
+		.mwdma_mask	= 0x07,			/* mwdma0-2 */
+		.udma_mask	= 0x3f,			/* udma0-5 */
+		.port_ops	= &sil_ops,
+	},
+	/* sil_3114 */
+	{
+		.sht		= &sil_sht,
+		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+				  ATA_FLAG_SRST | ATA_FLAG_MMIO |
+				  SIL_FLAG_RERR_ON_DMA_ACT,
 		.pio_mask	= 0x1f,			/* pio0-4 */
 		.mwdma_mask	= 0x07,			/* mwdma0-2 */
 		.udma_mask	= 0x3f,			/* udma0-5 */
@@ -216,12 +232,13 @@ static const struct {
 	unsigned long scr;	/* SATA control register block */
 	unsigned long sien;	/* SATA Interrupt Enable register */
 	unsigned long xfer_mode;/* data transfer mode register */
+	unsigned long sfis_cfg;	/* SATA FIS reception config register */
 } sil_port[] = {
 	/* port 0 ... */
-	{ 0x80, 0x8A, 0x00, 0x100, 0x148, 0xb4 },
-	{ 0xC0, 0xCA, 0x08, 0x180, 0x1c8, 0xf4 },
-	{ 0x280, 0x28A, 0x200, 0x300, 0x348, 0x2b4 },
-	{ 0x2C0, 0x2CA, 0x208, 0x380, 0x3c8, 0x2f4 },
+	{ 0x80, 0x8A, 0x00, 0x100, 0x148, 0xb4, 0x14c },
+	{ 0xC0, 0xCA, 0x08, 0x180, 0x1c8, 0xf4, 0x1cc },
+	{ 0x280, 0x28A, 0x200, 0x300, 0x348, 0x2b4, 0x34c },
+	{ 0x2C0, 0x2CA, 0x208, 0x380, 0x3c8, 0x2f4, 0x3cc },
 	/* ... port 3 */
 };
 
@@ -471,6 +488,23 @@ static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 		dev_printk(KERN_WARNING, &pdev->dev,
 			 "cache line size not set.  Driver may not function\n");
 
+	/* Apply R_ERR on DMA activate FIS errata workaround */
+	if (probe_ent->host_flags & SIL_FLAG_RERR_ON_DMA_ACT) {
+		int cnt;
+
+		for (i = 0, cnt = 0; i < probe_ent->n_ports; i++) {
+			tmp = readl(mmio_base + sil_port[i].sfis_cfg);
+			if ((tmp & 0x3) != 0x01)
+				continue;
+			if (!cnt)
+				dev_printk(KERN_INFO, &pdev->dev,
+					   "Applying R_ERR on DMA activate "
+					   "FIS errata fix\n");
+			writel(tmp & ~0x3, mmio_base + sil_port[i].sfis_cfg);
+			cnt++;
+		}
+	}
+
 	if (ent->driver_data == sil_3114) {
 		irq_mask = SIL_MASK_4PORT;
 
diff --git a/drivers/scsi/sata_vsc.c b/drivers/scsi/sata_vsc.c
index 2e2c3b7acb0..e484e8db681 100644
--- a/drivers/scsi/sata_vsc.c
+++ b/drivers/scsi/sata_vsc.c
@@ -81,6 +81,19 @@
 /* Port stride */
 #define VSC_SATA_PORT_OFFSET		0x200
 
+/* Error interrupt status bit offsets */
+#define VSC_SATA_INT_ERROR_E_OFFSET	2
+#define VSC_SATA_INT_ERROR_P_OFFSET	4
+#define VSC_SATA_INT_ERROR_T_OFFSET	5
+#define VSC_SATA_INT_ERROR_M_OFFSET	1
+#define is_vsc_sata_int_err(port_idx, int_status) \
+	 (int_status & ((1 << (VSC_SATA_INT_ERROR_E_OFFSET + (8 * port_idx))) | \
+		        (1 << (VSC_SATA_INT_ERROR_P_OFFSET + (8 * port_idx))) | \
+		        (1 << (VSC_SATA_INT_ERROR_T_OFFSET + (8 * port_idx))) | \
+		        (1 << (VSC_SATA_INT_ERROR_M_OFFSET + (8 * port_idx)))   \
+		       )\
+ 	 )
+
 
 static u32 vsc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
 {
@@ -201,13 +214,28 @@ static irqreturn_t vsc_sata_interrupt (int irq, void *dev_instance,
 			struct ata_port *ap;
 
 			ap = host_set->ports[i];
+
+			if (is_vsc_sata_int_err(i, int_status)) {
+				u32 err_status;
+				printk(KERN_DEBUG "%s: ignoring interrupt(s)\n", __FUNCTION__);
+				err_status = ap ? vsc_sata_scr_read(ap, SCR_ERROR) : 0;
+				vsc_sata_scr_write(ap, SCR_ERROR, err_status);
+				handled++;
+			}
+
 			if (ap && !(ap->flags &
 				    (ATA_FLAG_PORT_DISABLED|ATA_FLAG_NOINTR))) {
 				struct ata_queued_cmd *qc;
 
 				qc = ata_qc_from_tag(ap, ap->active_tag);
-				if (qc && (!(qc->tf.ctl & ATA_NIEN)))
+				if (qc && (!(qc->tf.ctl & ATA_NIEN))) {
 					handled += ata_host_intr(ap, qc);
+				} else {
+					printk(KERN_DEBUG "%s: ignoring interrupt(s)\n", __FUNCTION__);
+					ata_chk_status(ap);
+					handled++;
+				}
+
 			}
 		}
 	}
diff --git a/drivers/scsi/sd.c b/drivers/scsi/sd.c
index 930db398d10..9d9872347f5 100644
--- a/drivers/scsi/sd.c
+++ b/drivers/scsi/sd.c
@@ -89,6 +89,11 @@
 #define SD_MAX_RETRIES		5
 #define SD_PASSTHROUGH_RETRIES	1
 
+/*
+ * Size of the initial data buffer for mode and read capacity data
+ */
+#define SD_BUF_SIZE		512
+
 static void scsi_disk_release(struct kref *kref);
 
 struct scsi_disk {
@@ -1239,7 +1244,7 @@ sd_do_mode_sense(struct scsi_device *sdp, int dbd, int modepage,
 
 /*
  * read write protect setting, if possible - called only in sd_revalidate_disk()
- * called with buffer of length 512
+ * called with buffer of length SD_BUF_SIZE
  */
 static void
 sd_read_write_protect_flag(struct scsi_disk *sdkp, char *diskname,
@@ -1297,7 +1302,7 @@ sd_read_write_protect_flag(struct scsi_disk *sdkp, char *diskname,
 
 /*
  * sd_read_cache_type - called only from sd_revalidate_disk()
- * called with buffer of length 512
+ * called with buffer of length SD_BUF_SIZE
  */
 static void
 sd_read_cache_type(struct scsi_disk *sdkp, char *diskname,
@@ -1342,6 +1347,8 @@ sd_read_cache_type(struct scsi_disk *sdkp, char *diskname,
 
 	/* Take headers and block descriptors into account */
 	len += data.header_length + data.block_descriptor_length;
+	if (len > SD_BUF_SIZE)
+		goto bad_sense;
 
 	/* Get the data */
 	res = sd_do_mode_sense(sdp, dbd, modepage, buffer, len, &data, &sshdr);
@@ -1354,6 +1361,12 @@ sd_read_cache_type(struct scsi_disk *sdkp, char *diskname,
 		int ct = 0;
 		int offset = data.header_length + data.block_descriptor_length;
 
+		if (offset >= SD_BUF_SIZE - 2) {
+			printk(KERN_ERR "%s: malformed MODE SENSE response",
+				diskname);
+			goto defaults;
+		}
+
 		if ((buffer[offset] & 0x3f) != modepage) {
 			printk(KERN_ERR "%s: got wrong page\n", diskname);
 			goto defaults;
@@ -1398,6 +1411,7 @@ defaults:
 	       diskname);
 	sdkp->WCE = 0;
 	sdkp->RCD = 0;
+	sdkp->DPOFUA = 0;
 }
 
 /**
@@ -1421,7 +1435,7 @@ static int sd_revalidate_disk(struct gendisk *disk)
 	if (!scsi_device_online(sdp))
 		goto out;
 
-	buffer = kmalloc(512, GFP_KERNEL | __GFP_DMA);
+	buffer = kmalloc(SD_BUF_SIZE, GFP_KERNEL | __GFP_DMA);
 	if (!buffer) {
 		printk(KERN_WARNING "(sd_revalidate_disk:) Memory allocation "
 		       "failure.\n");
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index b1fc97d5f64..7aca22c9976 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -2198,7 +2198,7 @@ serial8250_console_write(struct console *co, const char *s, unsigned int count)
 	touch_nmi_watchdog();
 
 	/*
-	 *	First save the UER then disable the interrupts
+	 *	First save the IER then disable the interrupts
 	 */
 	ier = serial_in(up, UART_IER);
 
@@ -2326,6 +2326,12 @@ static struct uart_driver serial8250_reg = {
 	.cons			= SERIAL8250_CONSOLE,
 };
 
+/*
+ * early_serial_setup - early registration for 8250 ports
+ *
+ * Setup an 8250 port structure prior to console initialisation.  Use
+ * after console initialisation will cause undefined behaviour.
+ */
 int __init early_serial_setup(struct uart_port *port)
 {
 	if (port->line >= ARRAY_SIZE(serial8250_ports))
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 0f4361c8466..b3c561abe3f 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -902,8 +902,8 @@ config SERIAL_JSM
 	  something like this to connect more than two modems to your Linux
 	  box, for instance in order to become a dial-in server. This driver
 	  supports PCI boards only.
-	  If you have a card like this, say Y here and read the file
-	  <file:Documentation/jsm.txt>.
+
+	  If you have a card like this, say Y here, otherwise say N.
 
 	  To compile this driver as a module, choose M here: the
 	  module will be called jsm.
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 791c4dc550a..94f5e8ed83a 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -90,7 +90,7 @@ static int spi_suspend(struct device *dev, pm_message_t message)
 	int			value;
 	struct spi_driver	*drv = to_spi_driver(dev->driver);
 
-	if (!drv->suspend)
+	if (!drv || !drv->suspend)
 		return 0;
 
 	/* suspend will stop irqs and dma; no more i/o */
@@ -105,7 +105,7 @@ static int spi_resume(struct device *dev)
 	int			value;
 	struct spi_driver	*drv = to_spi_driver(dev->driver);
 
-	if (!drv->resume)
+	if (!drv || !drv->resume)
 		return 0;
 
 	/* resume may restart the i/o queue */
@@ -449,7 +449,6 @@ void spi_unregister_master(struct spi_master *master)
 {
 	(void) device_for_each_child(master->cdev.dev, NULL, __unregister);
 	class_device_unregister(&master->cdev);
-	master->cdev.dev = NULL;
 }
 EXPORT_SYMBOL_GPL(spi_unregister_master);
 
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index e64ed16bd42..f5079c78ba4 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -520,7 +520,7 @@ config FB_GBE
 config FB_GBE_MEM
 	int "Video memory size in MB"
 	depends on FB_GBE
-	default 8
+	default 4
 	help
 	  This is the amount of memory reserved for the framebuffer,
 	  which can be any value between 1MB and 8MB.
diff --git a/drivers/video/asiliantfb.c b/drivers/video/asiliantfb.c
index 69f75547865..c924d81f797 100644
--- a/drivers/video/asiliantfb.c
+++ b/drivers/video/asiliantfb.c
@@ -322,32 +322,29 @@ static int asiliantfb_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
 	writeb(green, mmio_base + 0x791);
 	writeb(blue, mmio_base + 0x791);
 
-	switch(p->var.bits_per_pixel) {
-	case 15:
-		if (regno < 16) {
+	if (regno < 16) {
+		switch(p->var.red.offset) {
+		case 10: /* RGB 555 */
 			((u32 *)(p->pseudo_palette))[regno] =
 				((red & 0xf8) << 7) |
 				((green & 0xf8) << 2) |
 				((blue & 0xf8) >> 3);
-		}
-		break;
-	case 16:
-		if (regno < 16) {
+			break;
+		case 11: /* RGB 565 */
 			((u32 *)(p->pseudo_palette))[regno] =
 				((red & 0xf8) << 8) |
 				((green & 0xfc) << 3) |
 				((blue & 0xf8) >> 3);
-		}
-		break;
-	case 24:
-		if (regno < 24) {
+			break;
+		case 16: /* RGB 888 */
 			((u32 *)(p->pseudo_palette))[regno] =
 				(red << 16)  |
 				(green << 8) |
 				(blue);
+			break;
 		}
-		break;
 	}
+
 	return 0;
 }
 
diff --git a/drivers/video/aty/radeon_pm.c b/drivers/video/aty/radeon_pm.c
index 556895e9964..1f8d805c61e 100644
--- a/drivers/video/aty/radeon_pm.c
+++ b/drivers/video/aty/radeon_pm.c
@@ -1321,8 +1321,6 @@ static void radeon_pm_full_reset_sdram(struct radeonfb_info *rinfo)
 	mdelay( 15);
 }
 
-#ifdef CONFIG_PPC_OF
-
 static void radeon_pm_reset_pad_ctlr_strength(struct radeonfb_info *rinfo)
 {
 	u32 tmp, tmp2;
@@ -1836,6 +1834,8 @@ static void radeon_reinitialize_M10(struct radeonfb_info *rinfo)
 	radeon_pm_m10_enable_lvds_spread_spectrum(rinfo);
 }
 
+#ifdef CONFIG_PPC_OF
+
 static void radeon_pm_m9p_reconfigure_mc(struct radeonfb_info *rinfo)
 {
 	OUTREG(MC_CNTL, rinfo->save_regs[46]);
@@ -2728,13 +2728,23 @@ void radeonfb_pm_init(struct radeonfb_info *rinfo, int dynclk)
 		printk("radeonfb: Dynamic Clock Power Management disabled\n");
 	}
 
+#if defined(CONFIG_PM)
 	/* Check if we can power manage on suspend/resume. We can do
 	 * D2 on M6, M7 and M9, and we can resume from D3 cold a few other
 	 * "Mac" cards, but that's all. We need more infos about what the
 	 * BIOS does tho. Right now, all this PM stuff is pmac-only for that
 	 * reason. --BenH
 	 */
-#if defined(CONFIG_PM) && defined(CONFIG_PPC_PMAC)
+	/* Special case for Samsung P35 laptops
+	 */
+	if ((rinfo->pdev->vendor == PCI_VENDOR_ID_ATI) &&
+	    (rinfo->pdev->device == PCI_CHIP_RV350_NP) &&
+	    (rinfo->pdev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG) &&
+	    (rinfo->pdev->subsystem_device == 0xc00c)) {
+		rinfo->reinit_func = radeon_reinitialize_M10;
+		rinfo->pm_mode |= radeon_pm_off;
+	}
+#if defined(CONFIG_PPC_PMAC)
 	if (_machine == _MACH_Pmac && rinfo->of_node) {
 		if (rinfo->is_mobility && rinfo->pm_reg &&
 		    rinfo->family <= CHIP_FAMILY_RV250)
@@ -2778,7 +2788,8 @@ void radeonfb_pm_init(struct radeonfb_info *rinfo, int dynclk)
 		OUTREG(TV_DAC_CNTL, INREG(TV_DAC_CNTL) | 0x07000000);
 #endif
 	}
-#endif /* defined(CONFIG_PM) && defined(CONFIG_PPC_PMAC) */
+#endif /* defined(CONFIG_PPC_PMAC) */
+#endif /* defined(CONFIG_PM) */
 }
 
 void radeonfb_pm_exit(struct radeonfb_info *rinfo)
diff --git a/drivers/video/au1100fb.c b/drivers/video/au1100fb.c
index 2406899f120..3d04b2def0f 100644
--- a/drivers/video/au1100fb.c
+++ b/drivers/video/au1100fb.c
@@ -49,6 +49,7 @@
 #include <linux/interrupt.h>
 #include <linux/ctype.h>
 #include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
 
 #include <asm/mach-au1x00/au1000.h>
 
@@ -406,7 +407,7 @@ int au1100fb_fb_mmap(struct fb_info *fbi, struct vm_area_struct *vma)
 
 	vma->vm_flags |= VM_IO;
 
-	if (io_remap_page_range(vma, vma->vm_start, off,
+	if (io_remap_pfn_range(vma, vma->vm_start, off >> PAGE_SHIFT,
 				vma->vm_end - vma->vm_start,
 				vma->vm_page_prot)) {
 		return -EAGAIN;
diff --git a/drivers/video/console/vgacon.c b/drivers/video/console/vgacon.c
index 12d9329d140..5a86978537d 100644
--- a/drivers/video/console/vgacon.c
+++ b/drivers/video/console/vgacon.c
@@ -509,57 +509,60 @@ static int vgacon_doresize(struct vc_data *c,
 {
 	unsigned long flags;
 	unsigned int scanlines = height * c->vc_font.height;
-	u8 scanlines_lo, r7, vsync_end, mode, max_scan;
+	u8 scanlines_lo = 0, r7 = 0, vsync_end = 0, mode, max_scan;
 
 	spin_lock_irqsave(&vga_lock, flags);
 
-	outb_p(VGA_CRTC_MAX_SCAN, vga_video_port_reg);
-	max_scan = inb_p(vga_video_port_val);
-
-	if (max_scan & 0x80)
-		scanlines <<= 1;
-
 	vgacon_xres = width * VGA_FONTWIDTH;
 	vgacon_yres = height * c->vc_font.height;
-	outb_p(VGA_CRTC_MODE, vga_video_port_reg);
-	mode = inb_p(vga_video_port_val);
+	if (vga_video_type >= VIDEO_TYPE_VGAC) {
+		outb_p(VGA_CRTC_MAX_SCAN, vga_video_port_reg);
+		max_scan = inb_p(vga_video_port_val);
 
-	if (mode & 0x04)
-		scanlines >>= 1;
+		if (max_scan & 0x80)
+			scanlines <<= 1;
 
-	scanlines -= 1;
-	scanlines_lo = scanlines & 0xff;
+		outb_p(VGA_CRTC_MODE, vga_video_port_reg);
+		mode = inb_p(vga_video_port_val);
 
-	outb_p(VGA_CRTC_OVERFLOW, vga_video_port_reg);
-	r7 = inb_p(vga_video_port_val) & ~0x42;
+		if (mode & 0x04)
+			scanlines >>= 1;
 
-	if (scanlines & 0x100)
-		r7 |= 0x02;
-	if (scanlines & 0x200)
-		r7 |= 0x40;
+		scanlines -= 1;
+		scanlines_lo = scanlines & 0xff;
 
-	/* deprotect registers */
-	outb_p(VGA_CRTC_V_SYNC_END, vga_video_port_reg);
-	vsync_end = inb_p(vga_video_port_val);
-	outb_p(VGA_CRTC_V_SYNC_END, vga_video_port_reg);
-	outb_p(vsync_end & ~0x80, vga_video_port_val);
+		outb_p(VGA_CRTC_OVERFLOW, vga_video_port_reg);
+		r7 = inb_p(vga_video_port_val) & ~0x42;
+
+		if (scanlines & 0x100)
+			r7 |= 0x02;
+		if (scanlines & 0x200)
+			r7 |= 0x40;
+
+		/* deprotect registers */
+		outb_p(VGA_CRTC_V_SYNC_END, vga_video_port_reg);
+		vsync_end = inb_p(vga_video_port_val);
+		outb_p(VGA_CRTC_V_SYNC_END, vga_video_port_reg);
+		outb_p(vsync_end & ~0x80, vga_video_port_val);
+	}
 
 	outb_p(VGA_CRTC_H_DISP, vga_video_port_reg);
 	outb_p(width - 1, vga_video_port_val);
 	outb_p(VGA_CRTC_OFFSET, vga_video_port_reg);
 	outb_p(width >> 1, vga_video_port_val);
 
-	outb_p(VGA_CRTC_V_DISP_END, vga_video_port_reg);
-	outb_p(scanlines_lo, vga_video_port_val);
-	outb_p(VGA_CRTC_OVERFLOW, vga_video_port_reg);
-	outb_p(r7,vga_video_port_val);
+	if (vga_video_type >= VIDEO_TYPE_VGAC) {
+		outb_p(VGA_CRTC_V_DISP_END, vga_video_port_reg);
+		outb_p(scanlines_lo, vga_video_port_val);
+		outb_p(VGA_CRTC_OVERFLOW, vga_video_port_reg);
+		outb_p(r7,vga_video_port_val);
 
-	/* reprotect registers */
-	outb_p(VGA_CRTC_V_SYNC_END, vga_video_port_reg);
-	outb_p(vsync_end, vga_video_port_val);
+		/* reprotect registers */
+		outb_p(VGA_CRTC_V_SYNC_END, vga_video_port_reg);
+		outb_p(vsync_end, vga_video_port_val);
+	}
 
 	spin_unlock_irqrestore(&vga_lock, flags);
-
 	return 0;
 }
 
diff --git a/drivers/video/gbefb.c b/drivers/video/gbefb.c
index 38d22729b12..5e25b986019 100644
--- a/drivers/video/gbefb.c
+++ b/drivers/video/gbefb.c
@@ -656,12 +656,15 @@ static int gbefb_set_par(struct fb_info *info)
 	switch (bytesPerPixel) {
 	case 1:
 		SET_GBE_FIELD(WID, TYP, val, GBE_CMODE_I8);
+		info->fix.visual = FB_VISUAL_PSEUDOCOLOR;
 		break;
 	case 2:
 		SET_GBE_FIELD(WID, TYP, val, GBE_CMODE_ARGB5);
+		info->fix.visual = FB_VISUAL_TRUECOLOR;
 		break;
 	case 4:
 		SET_GBE_FIELD(WID, TYP, val, GBE_CMODE_RGB8);
+		info->fix.visual = FB_VISUAL_TRUECOLOR;
 		break;
 	}
 	SET_GBE_FIELD(WID, BUF, val, GBE_BMODE_BOTH);
@@ -1243,7 +1246,7 @@ static int __devexit gbefb_remove(struct platform_device* p_dev)
 			  (void *)gbe_tiles.cpu, gbe_tiles.dma);
 	release_mem_region(GBE_BASE, sizeof(struct sgi_gbe));
 	iounmap(gbe);
-	gbefb_remove_sysfs(dev);
+	gbefb_remove_sysfs(&p_dev->dev);
 	framebuffer_release(info);
 
 	return 0;
diff --git a/drivers/video/s3c2410fb.c b/drivers/video/s3c2410fb.c
index d574dd3c9c8..9451932fbaf 100644
--- a/drivers/video/s3c2410fb.c
+++ b/drivers/video/s3c2410fb.c
@@ -82,7 +82,6 @@
 #include <linux/fb.h>
 #include <linux/init.h>
 #include <linux/dma-mapping.h>
-#include <linux/string.h>
 #include <linux/interrupt.h>
 #include <linux/workqueue.h>
 #include <linux/wait.h>