USB: EHCI: add delay during suspend to prevent erroneous wakeups

High-speed USB connections revert back to full-speed signalling when
the device goes into suspend.  This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.

On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state.  It generates a false wakeup signal,
which can prevent the controller from going to sleep.

To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling.  (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Peter Chen <Peter.Chen@freescale.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1 files changed, 22 insertions, 4 deletions

diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c
index 47b858fc50b..7ae0c4d5174 100644
--- a/drivers/usb/host/ehci-hub.c
+++ b/drivers/usb/host/ehci-hub.c
@@ -238,6 +238,7 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 	int			port;
 	int			mask;
 	int			changed;
+	bool			fs_idle_delay;
 
 	ehci_dbg(ehci, "suspend root hub\n");
 
@@ -272,6 +273,7 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 	ehci->bus_suspended = 0;
 	ehci->owned_ports = 0;
 	changed = 0;
+	fs_idle_delay = false;
 	port = HCS_N_PORTS(ehci->hcs_params);
 	while (port--) {
 		u32 __iomem	*reg = &ehci->regs->port_status [port];
@@ -300,16 +302,32 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 		}
 
 		if (t1 != t2) {
+			/*
+			 * On some controllers, Wake-On-Disconnect will
+			 * generate false wakeup signals until the bus
+			 * switches over to full-speed idle.  For their
+			 * sake, add a delay if we need one.
+			 */
+			if ((t2 & PORT_WKDISC_E) &&
+					ehci_port_speed(ehci, t2) ==
+						USB_PORT_STAT_HIGH_SPEED)
+				fs_idle_delay = true;
 			ehci_writel(ehci, t2, reg);
 			changed = 1;
 		}
 	}
+	spin_unlock_irq(&ehci->lock);
+
+	if ((changed && ehci->has_tdi_phy_lpm) || fs_idle_delay) {
+		/*
+		 * Wait for HCD to enter low-power mode or for the bus
+		 * to switch to full-speed idle.
+		 */
+		usleep_range(5000, 5500);
+	}
 
 	if (changed && ehci->has_tdi_phy_lpm) {
-		spin_unlock_irq(&ehci->lock);
-		msleep(5);	/* 5 ms for HCD to enter low-power mode */
 		spin_lock_irq(&ehci->lock);
-
 		port = HCS_N_PORTS(ehci->hcs_params);
 		while (port--) {
 			u32 __iomem	*hostpc_reg = &ehci->regs->hostpc[port];
@@ -322,8 +340,8 @@ static int ehci_bus_suspend (struct usb_hcd *hcd)
 					port, (t3 & HOSTPC_PHCD) ?
 					"succeeded" : "failed");
 		}
+		spin_unlock_irq(&ehci->lock);
 	}
-	spin_unlock_irq(&ehci->lock);
 
 	/* Apparently some devices need a >= 1-uframe delay here */
 	if (ehci->bus_suspended)