diff options
| author | Luben Tuikov <ltuikov@yahoo.com> | 2011-02-11 11:33:10 -0800 |
|---|---|---|
| committer | Greg Kroah-Hartman <gregkh@suse.de> | 2011-02-17 10:30:24 -0800 |
| commit | 637d11bfb814637ec7b81e878db3ffea6408a89a (patch) | |
| tree | 29b7fa9e237784e0c301e88ff83c5ba4935167a6 /drivers/usb | |
| parent | 72a012ce0a02c6c616676a24b40ff81d1aaeafda (diff) | |
USB: Reset USB 3.0 devices on (re)discovery
If the device isn't reset, the XHCI HCD sends
SET ADDRESS to address 0 while the device is
already in Addressed state, and the request is
dropped on the floor as it is addressed to the
default address. This sequence of events, which this
patch fixes looks like this:
usb_reset_and_verify_device()
hub_port_init()
hub_set_address()
SET_ADDRESS to 0 with 1
usb_get_device_descriptor(udev, 8)
usb_get_device_descriptor(udev, 18)
descriptors_changed() --> goto re_enumerate:
hub_port_logical_disconnect()
kick_khubd()
And then:
hub_events()
hub_port_connect_change()
usb_disconnect()
usb_disable_device()
new device struct
sets device state to Powered
choose_address()
hub_port_init() <-- no reset, but SET ADDRESS to 0 with 1, timeout!
The solution is to always reset the device in
hub_port_init() to put it in a known state.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Diffstat (limited to 'drivers/usb')
| -rw-r--r-- | drivers/usb/core/hub.c | 18 |
1 files changed, 7 insertions, 11 deletions
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index d041c6826e4..0f299b7aad6 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -2681,17 +2681,13 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, mutex_lock(&usb_address0_mutex); - if (!udev->config && oldspeed == USB_SPEED_SUPER) { - /* Don't reset USB 3.0 devices during an initial setup */ - usb_set_device_state(udev, USB_STATE_DEFAULT); - } else { - /* Reset the device; full speed may morph to high speed */ - /* FIXME a USB 2.0 device may morph into SuperSpeed on reset. */ - retval = hub_port_reset(hub, port1, udev, delay); - if (retval < 0) /* error or disconnect */ - goto fail; - /* success, speed is known */ - } + /* Reset the device; full speed may morph to high speed */ + /* FIXME a USB 2.0 device may morph into SuperSpeed on reset. */ + retval = hub_port_reset(hub, port1, udev, delay); + if (retval < 0) /* error or disconnect */ + goto fail; + /* success, speed is known */ + retval = -ENODEV; if (oldspeed != USB_SPEED_UNKNOWN && oldspeed != udev->speed) { |