EHCI: centralize controller initialization

This patch (as1564c) converts the EHCI platform drivers to use the
central ehci_setup() routine for generic controller initialization
rather than each having its own idiosyncratic approach.

The major point of difficulty lies in ehci-pci's many vendor- and
device-specific workarounds.  Some of them have to be applied before
calling ehci_setup() and some after, which necessitates a fair amount
of code motion.  The other platform drivers require much smaller
changes.

One point not addressed by the patch is whether ports should be
powered on or off following initialization.  The different drivers
appear to handle this pretty much at random.  In fact it shouldn't
matter, because the hub driver turns on power to all ports when it
binds to the root hub.  Straightening that out will be left for
another day.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1 files changed, 51 insertions, 53 deletions

diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index 6e15fc87cf6..6133d93808d 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -145,6 +145,56 @@ static void omap_ehci_soft_phy_reset(struct platform_device *pdev, u8 port)
 	}
 }
 
+static int omap_ehci_init(struct usb_hcd *hcd)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci(hcd);
+	int			rc;
+	struct ehci_hcd_omap_platform_data	*pdata;
+
+	pdata = hcd->self.controller->platform_data;
+	if (pdata->phy_reset) {
+		if (gpio_is_valid(pdata->reset_gpio_port[0]))
+			gpio_request_one(pdata->reset_gpio_port[0],
+					 GPIOF_OUT_INIT_LOW, "USB1 PHY reset");
+
+		if (gpio_is_valid(pdata->reset_gpio_port[1]))
+			gpio_request_one(pdata->reset_gpio_port[1],
+					 GPIOF_OUT_INIT_LOW, "USB2 PHY reset");
+
+		/* Hold the PHY in RESET for enough time till DIR is high */
+		udelay(10);
+	}
+
+	/* Soft reset the PHY using PHY reset command over ULPI */
+	if (pdata->port_mode[0] == OMAP_EHCI_PORT_MODE_PHY)
+		omap_ehci_soft_phy_reset(pdev, 0);
+	if (pdata->port_mode[1] == OMAP_EHCI_PORT_MODE_PHY)
+		omap_ehci_soft_phy_reset(pdev, 1);
+
+	/* we know this is the memory we want, no need to ioremap again */
+	ehci->caps = hcd->regs;
+
+	rc = ehci_setup(hcd);
+
+	if (pdata->phy_reset) {
+		/* Hold the PHY in RESET for enough time till
+		 * PHY is settled and ready
+		 */
+		udelay(10);
+
+		if (gpio_is_valid(pdata->reset_gpio_port[0]))
+			gpio_set_value_cansleep(pdata->reset_gpio_port[0], 1);
+
+		if (gpio_is_valid(pdata->reset_gpio_port[1]))
+			gpio_set_value_cansleep(pdata->reset_gpio_port[1], 1);
+	}
+
+	/* root ports should always stay powered */
+	ehci_port_power(ehci, 1);
+
+	return rc;
+}
+
 static int omap_ehci_hub_control(
 	struct usb_hcd	*hcd,
 	u16		typeReq,
@@ -219,7 +269,6 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
 	struct resource				*res;
 	struct usb_hcd				*hcd;
 	void __iomem				*regs;
-	struct ehci_hcd				*omap_ehci;
 	int					ret = -ENODEV;
 	int					irq;
 	int					i;
@@ -281,19 +330,6 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
 		}
 	}
 
-	if (pdata->phy_reset) {
-		if (gpio_is_valid(pdata->reset_gpio_port[0]))
-			gpio_request_one(pdata->reset_gpio_port[0],
-					 GPIOF_OUT_INIT_LOW, "USB1 PHY reset");
-
-		if (gpio_is_valid(pdata->reset_gpio_port[1]))
-			gpio_request_one(pdata->reset_gpio_port[1],
-					 GPIOF_OUT_INIT_LOW, "USB2 PHY reset");
-
-		/* Hold the PHY in RESET for enough time till DIR is high */
-		udelay(10);
-	}
-
 	pm_runtime_enable(dev);
 	pm_runtime_get_sync(dev);
 
@@ -309,50 +345,12 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
 	ehci_write(regs, EHCI_INSNREG04,
 				EHCI_INSNREG04_DISABLE_UNSUSPEND);
 
-	/* Soft reset the PHY using PHY reset command over ULPI */
-	if (pdata->port_mode[0] == OMAP_EHCI_PORT_MODE_PHY)
-		omap_ehci_soft_phy_reset(pdev, 0);
-	if (pdata->port_mode[1] == OMAP_EHCI_PORT_MODE_PHY)
-		omap_ehci_soft_phy_reset(pdev, 1);
-
-	omap_ehci = hcd_to_ehci(hcd);
-	omap_ehci->sbrn = 0x20;
-
-	/* we know this is the memory we want, no need to ioremap again */
-	omap_ehci->caps = hcd->regs;
-	omap_ehci->regs = hcd->regs
-		+ HC_LENGTH(ehci, readl(&omap_ehci->caps->hc_capbase));
-
-	dbg_hcs_params(omap_ehci, "reset");
-	dbg_hcc_params(omap_ehci, "reset");
-
-	/* cache this readonly data; minimize chip reads */
-	omap_ehci->hcs_params = readl(&omap_ehci->caps->hcs_params);
-
-	ehci_reset(omap_ehci);
-
-	if (pdata->phy_reset) {
-		/* Hold the PHY in RESET for enough time till
-		 * PHY is settled and ready
-		 */
-		udelay(10);
-
-		if (gpio_is_valid(pdata->reset_gpio_port[0]))
-			gpio_set_value_cansleep(pdata->reset_gpio_port[0], 1);
-
-		if (gpio_is_valid(pdata->reset_gpio_port[1]))
-			gpio_set_value_cansleep(pdata->reset_gpio_port[1], 1);
-	}
-
 	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
 	if (ret) {
 		dev_err(dev, "failed to add hcd with err %d\n", ret);
 		goto err_pm_runtime;
 	}
 
-	/* root ports should always stay powered */
-	ehci_port_power(omap_ehci, 1);
-
 	/* get clocks */
 	utmi_p1_fck = clk_get(dev, "utmi_p1_gfclk");
 	if (IS_ERR(utmi_p1_fck)) {
@@ -512,7 +510,7 @@ static const struct hc_driver ehci_omap_hc_driver = {
 	/*
 	 * basic lifecycle operations
 	 */
-	.reset			= ehci_init,
+	.reset			= omap_ehci_init,
 	.start			= ehci_run,
 	.stop			= ehci_stop,
 	.shutdown		= ehci_shutdown,