Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 2909 insertions, 0 deletions

diff --git a/drivers/serial/ioc4_serial.c b/drivers/serial/ioc4_serial.c
new file mode 100644
index 00000000000..d054f126570
--- /dev/null
+++ b/drivers/serial/ioc4_serial.c
@@ -0,0 +1,2909 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003-2005 Silicon Graphics, Inc.  All Rights Reserved.
+ */
+
+
+/*
+ * This file contains a module version of the ioc4 serial driver. This
+ * includes all the support functions needed (support functions, etc.)
+ * and the serial driver itself.
+ */
+#include <linux/errno.h>
+#include <linux/tty.h>
+#include <linux/serial.h>
+#include <linux/serialP.h>
+#include <linux/circ_buf.h>
+#include <linux/serial_reg.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/ioc4_common.h>
+#include <linux/serial_core.h>
+
+/*
+ * interesting things about the ioc4
+ */
+
+#define IOC4_NUM_SERIAL_PORTS	4	/* max ports per card */
+#define IOC4_NUM_CARDS		8	/* max cards per partition */
+
+#define	GET_SIO_IR(_n)	(_n == 0) ? (IOC4_SIO_IR_S0) : \
+				(_n == 1) ? (IOC4_SIO_IR_S1) : \
+				(_n == 2) ? (IOC4_SIO_IR_S2) : \
+				(IOC4_SIO_IR_S3)
+
+#define	GET_OTHER_IR(_n)  (_n == 0) ? (IOC4_OTHER_IR_S0_MEMERR) : \
+				(_n == 1) ? (IOC4_OTHER_IR_S1_MEMERR) : \
+				(_n == 2) ? (IOC4_OTHER_IR_S2_MEMERR) : \
+				(IOC4_OTHER_IR_S3_MEMERR)
+
+
+/*
+ * All IOC4 registers are 32 bits wide.
+ */
+
+/*
+ * PCI Memory Space Map
+ */
+#define IOC4_PCI_ERR_ADDR_L     0x000	/* Low Error Address */
+#define IOC4_PCI_ERR_ADDR_VLD	        (0x1 << 0)
+#define IOC4_PCI_ERR_ADDR_MST_ID_MSK    (0xf << 1)
+#define IOC4_PCI_ERR_ADDR_MST_NUM_MSK   (0xe << 1)
+#define IOC4_PCI_ERR_ADDR_MST_TYP_MSK   (0x1 << 1)
+#define IOC4_PCI_ERR_ADDR_MUL_ERR       (0x1 << 5)
+#define IOC4_PCI_ERR_ADDR_ADDR_MSK      (0x3ffffff << 6)
+
+/* Interrupt types */
+#define	IOC4_SIO_INTR_TYPE	0
+#define	IOC4_OTHER_INTR_TYPE	1
+#define	IOC4_NUM_INTR_TYPES	2
+
+/* Bitmasks for IOC4_SIO_IR, IOC4_SIO_IEC, and IOC4_SIO_IES  */
+#define IOC4_SIO_IR_S0_TX_MT	   0x00000001	/* Serial port 0 TX empty */
+#define IOC4_SIO_IR_S0_RX_FULL	   0x00000002	/* Port 0 RX buf full */
+#define IOC4_SIO_IR_S0_RX_HIGH	   0x00000004	/* Port 0 RX hiwat */
+#define IOC4_SIO_IR_S0_RX_TIMER	   0x00000008	/* Port 0 RX timeout */
+#define IOC4_SIO_IR_S0_DELTA_DCD   0x00000010	/* Port 0 delta DCD */
+#define IOC4_SIO_IR_S0_DELTA_CTS   0x00000020	/* Port 0 delta CTS */
+#define IOC4_SIO_IR_S0_INT	   0x00000040	/* Port 0 pass-thru intr */
+#define IOC4_SIO_IR_S0_TX_EXPLICIT 0x00000080	/* Port 0 explicit TX thru */
+#define IOC4_SIO_IR_S1_TX_MT	   0x00000100	/* Serial port 1 */
+#define IOC4_SIO_IR_S1_RX_FULL	   0x00000200	/* */
+#define IOC4_SIO_IR_S1_RX_HIGH	   0x00000400	/* */
+#define IOC4_SIO_IR_S1_RX_TIMER	   0x00000800	/* */
+#define IOC4_SIO_IR_S1_DELTA_DCD   0x00001000	/* */
+#define IOC4_SIO_IR_S1_DELTA_CTS   0x00002000	/* */
+#define IOC4_SIO_IR_S1_INT	   0x00004000	/* */
+#define IOC4_SIO_IR_S1_TX_EXPLICIT 0x00008000	/* */
+#define IOC4_SIO_IR_S2_TX_MT	   0x00010000	/* Serial port 2 */
+#define IOC4_SIO_IR_S2_RX_FULL	   0x00020000	/* */
+#define IOC4_SIO_IR_S2_RX_HIGH	   0x00040000	/* */
+#define IOC4_SIO_IR_S2_RX_TIMER	   0x00080000	/* */
+#define IOC4_SIO_IR_S2_DELTA_DCD   0x00100000	/* */
+#define IOC4_SIO_IR_S2_DELTA_CTS   0x00200000	/* */
+#define IOC4_SIO_IR_S2_INT	   0x00400000	/* */
+#define IOC4_SIO_IR_S2_TX_EXPLICIT 0x00800000	/* */
+#define IOC4_SIO_IR_S3_TX_MT	   0x01000000	/* Serial port 3 */
+#define IOC4_SIO_IR_S3_RX_FULL	   0x02000000	/* */
+#define IOC4_SIO_IR_S3_RX_HIGH	   0x04000000	/* */
+#define IOC4_SIO_IR_S3_RX_TIMER	   0x08000000	/* */
+#define IOC4_SIO_IR_S3_DELTA_DCD   0x10000000	/* */
+#define IOC4_SIO_IR_S3_DELTA_CTS   0x20000000	/* */
+#define IOC4_SIO_IR_S3_INT	   0x40000000	/* */
+#define IOC4_SIO_IR_S3_TX_EXPLICIT 0x80000000	/* */
+
+/* Per device interrupt masks */
+#define IOC4_SIO_IR_S0		(IOC4_SIO_IR_S0_TX_MT | \
+				 IOC4_SIO_IR_S0_RX_FULL | \
+				 IOC4_SIO_IR_S0_RX_HIGH | \
+				 IOC4_SIO_IR_S0_RX_TIMER | \
+				 IOC4_SIO_IR_S0_DELTA_DCD | \
+				 IOC4_SIO_IR_S0_DELTA_CTS | \
+				 IOC4_SIO_IR_S0_INT | \
+				 IOC4_SIO_IR_S0_TX_EXPLICIT)
+#define IOC4_SIO_IR_S1		(IOC4_SIO_IR_S1_TX_MT | \
+				 IOC4_SIO_IR_S1_RX_FULL | \
+				 IOC4_SIO_IR_S1_RX_HIGH | \
+				 IOC4_SIO_IR_S1_RX_TIMER | \
+				 IOC4_SIO_IR_S1_DELTA_DCD | \
+				 IOC4_SIO_IR_S1_DELTA_CTS | \
+				 IOC4_SIO_IR_S1_INT | \
+				 IOC4_SIO_IR_S1_TX_EXPLICIT)
+#define IOC4_SIO_IR_S2		(IOC4_SIO_IR_S2_TX_MT | \
+				 IOC4_SIO_IR_S2_RX_FULL | \
+				 IOC4_SIO_IR_S2_RX_HIGH | \
+				 IOC4_SIO_IR_S2_RX_TIMER | \
+				 IOC4_SIO_IR_S2_DELTA_DCD | \
+				 IOC4_SIO_IR_S2_DELTA_CTS | \
+				 IOC4_SIO_IR_S2_INT | \
+				 IOC4_SIO_IR_S2_TX_EXPLICIT)
+#define IOC4_SIO_IR_S3		(IOC4_SIO_IR_S3_TX_MT | \
+				 IOC4_SIO_IR_S3_RX_FULL | \
+				 IOC4_SIO_IR_S3_RX_HIGH | \
+				 IOC4_SIO_IR_S3_RX_TIMER | \
+				 IOC4_SIO_IR_S3_DELTA_DCD | \
+				 IOC4_SIO_IR_S3_DELTA_CTS | \
+				 IOC4_SIO_IR_S3_INT | \
+				 IOC4_SIO_IR_S3_TX_EXPLICIT)
+
+/* Bitmasks for IOC4_OTHER_IR, IOC4_OTHER_IEC, and IOC4_OTHER_IES  */
+#define IOC4_OTHER_IR_ATA_INT           0x00000001  /* ATAPI intr pass-thru */
+#define IOC4_OTHER_IR_ATA_MEMERR        0x00000002  /* ATAPI DMA PCI error */
+#define IOC4_OTHER_IR_S0_MEMERR         0x00000004  /* Port 0 PCI error */
+#define IOC4_OTHER_IR_S1_MEMERR         0x00000008  /* Port 1 PCI error */
+#define IOC4_OTHER_IR_S2_MEMERR         0x00000010  /* Port 2 PCI error */
+#define IOC4_OTHER_IR_S3_MEMERR         0x00000020  /* Port 3 PCI error */
+
+/* Bitmasks for IOC4_SIO_CR */
+#define IOC4_SIO_CR_CMD_PULSE_SHIFT              0  /* byte bus strobe shift */
+#define IOC4_SIO_CR_ARB_DIAG_TX0	0x00000000
+#define IOC4_SIO_CR_ARB_DIAG_RX0	0x00000010
+#define IOC4_SIO_CR_ARB_DIAG_TX1	0x00000020
+#define IOC4_SIO_CR_ARB_DIAG_RX1	0x00000030
+#define IOC4_SIO_CR_ARB_DIAG_TX2	0x00000040
+#define IOC4_SIO_CR_ARB_DIAG_RX2	0x00000050
+#define IOC4_SIO_CR_ARB_DIAG_TX3	0x00000060
+#define IOC4_SIO_CR_ARB_DIAG_RX3	0x00000070
+#define IOC4_SIO_CR_SIO_DIAG_IDLE	0x00000080  /* 0 -> active request among
+							   serial ports (ro) */
+/* Defs for some of the generic I/O pins */
+#define IOC4_GPCR_UART0_MODESEL	   0x10	/* Pin is output to port 0
+						   mode sel */
+#define IOC4_GPCR_UART1_MODESEL	   0x20	/* Pin is output to port 1
+						   mode sel */
+#define IOC4_GPCR_UART2_MODESEL	   0x40	/* Pin is output to port 2
+						   mode sel */
+#define IOC4_GPCR_UART3_MODESEL	   0x80	/* Pin is output to port 3
+						   mode sel */
+
+#define IOC4_GPPR_UART0_MODESEL_PIN   4	/* GIO pin controlling
+					   uart 0 mode select */
+#define IOC4_GPPR_UART1_MODESEL_PIN   5	/* GIO pin controlling
+					   uart 1 mode select */
+#define IOC4_GPPR_UART2_MODESEL_PIN   6	/* GIO pin controlling
+					   uart 2 mode select */
+#define IOC4_GPPR_UART3_MODESEL_PIN   7	/* GIO pin controlling
+					   uart 3 mode select */
+
+/* Bitmasks for serial RX status byte */
+#define IOC4_RXSB_OVERRUN       0x01	/* Char(s) lost */
+#define IOC4_RXSB_PAR_ERR	0x02	/* Parity error */
+#define IOC4_RXSB_FRAME_ERR	0x04	/* Framing error */
+#define IOC4_RXSB_BREAK	        0x08	/* Break character */
+#define IOC4_RXSB_CTS	        0x10	/* State of CTS */
+#define IOC4_RXSB_DCD	        0x20	/* State of DCD */
+#define IOC4_RXSB_MODEM_VALID   0x40	/* DCD, CTS, and OVERRUN are valid */
+#define IOC4_RXSB_DATA_VALID    0x80	/* Data byte, FRAME_ERR PAR_ERR
+					 * & BREAK valid */
+
+/* Bitmasks for serial TX control byte */
+#define IOC4_TXCB_INT_WHEN_DONE 0x20	/* Interrupt after this byte is sent */
+#define IOC4_TXCB_INVALID	0x00	/* Byte is invalid */
+#define IOC4_TXCB_VALID	        0x40	/* Byte is valid */
+#define IOC4_TXCB_MCR	        0x80	/* Data<7:0> to modem control reg */
+#define IOC4_TXCB_DELAY	        0xc0	/* Delay data<7:0> mSec */
+
+/* Bitmasks for IOC4_SBBR_L */
+#define IOC4_SBBR_L_SIZE	0x00000001  /* 0 == 1KB rings, 1 == 4KB rings */
+
+/* Bitmasks for IOC4_SSCR_<3:0> */
+#define IOC4_SSCR_RX_THRESHOLD  0x000001ff  /* Hiwater mark */
+#define IOC4_SSCR_TX_TIMER_BUSY 0x00010000  /* TX timer in progress */
+#define IOC4_SSCR_HFC_EN	0x00020000  /* Hardware flow control enabled */
+#define IOC4_SSCR_RX_RING_DCD   0x00040000  /* Post RX record on delta-DCD */
+#define IOC4_SSCR_RX_RING_CTS   0x00080000  /* Post RX record on delta-CTS */
+#define IOC4_SSCR_DIAG	        0x00200000  /* Bypass clock divider for sim */
+#define IOC4_SSCR_RX_DRAIN	0x08000000  /* Drain RX buffer to memory */
+#define IOC4_SSCR_DMA_EN	0x10000000  /* Enable ring buffer DMA */
+#define IOC4_SSCR_DMA_PAUSE	0x20000000  /* Pause DMA */
+#define IOC4_SSCR_PAUSE_STATE   0x40000000  /* Sets when PAUSE takes effect */
+#define IOC4_SSCR_RESET	        0x80000000  /* Reset DMA channels */
+
+/* All producer/comsumer pointers are the same bitfield */
+#define IOC4_PROD_CONS_PTR_4K   0x00000ff8	/* For 4K buffers */
+#define IOC4_PROD_CONS_PTR_1K   0x000003f8	/* For 1K buffers */
+#define IOC4_PROD_CONS_PTR_OFF           3
+
+/* Bitmasks for IOC4_SRCIR_<3:0> */
+#define IOC4_SRCIR_ARM	        0x80000000	/* Arm RX timer */
+
+/* Bitmasks for IOC4_SHADOW_<3:0> */
+#define IOC4_SHADOW_DR	 0x00000001	/* Data ready */
+#define IOC4_SHADOW_OE	 0x00000002	/* Overrun error */
+#define IOC4_SHADOW_PE	 0x00000004	/* Parity error */
+#define IOC4_SHADOW_FE	 0x00000008	/* Framing error */
+#define IOC4_SHADOW_BI	 0x00000010	/* Break interrupt */
+#define IOC4_SHADOW_THRE 0x00000020	/* Xmit holding register empty */
+#define IOC4_SHADOW_TEMT 0x00000040	/* Xmit shift register empty */
+#define IOC4_SHADOW_RFCE 0x00000080	/* Char in RX fifo has an error */
+#define IOC4_SHADOW_DCTS 0x00010000	/* Delta clear to send */
+#define IOC4_SHADOW_DDCD 0x00080000	/* Delta data carrier detect */
+#define IOC4_SHADOW_CTS	 0x00100000	/* Clear to send */
+#define IOC4_SHADOW_DCD	 0x00800000	/* Data carrier detect */
+#define IOC4_SHADOW_DTR	 0x01000000	/* Data terminal ready */
+#define IOC4_SHADOW_RTS	 0x02000000	/* Request to send */
+#define IOC4_SHADOW_OUT1 0x04000000	/* 16550 OUT1 bit */
+#define IOC4_SHADOW_OUT2 0x08000000	/* 16550 OUT2 bit */
+#define IOC4_SHADOW_LOOP 0x10000000	/* Loopback enabled */
+
+/* Bitmasks for IOC4_SRTR_<3:0> */
+#define IOC4_SRTR_CNT	        0x00000fff	/* Reload value for RX timer */
+#define IOC4_SRTR_CNT_VAL	0x0fff0000	/* Current value of RX timer */
+#define IOC4_SRTR_CNT_VAL_SHIFT         16
+#define IOC4_SRTR_HZ                 16000	/* SRTR clock frequency */
+
+/* Serial port register map used for DMA and PIO serial I/O */
+struct ioc4_serialregs {
+	uint32_t sscr;
+	uint32_t stpir;
+	uint32_t stcir;
+	uint32_t srpir;
+	uint32_t srcir;
+	uint32_t srtr;
+	uint32_t shadow;
+};
+
+/* IOC4 UART register map */
+struct ioc4_uartregs {
+	char i4u_lcr;
+	union {
+		char iir;	/* read only */
+		char fcr;	/* write only */
+	} u3;
+	union {
+		char ier;	/* DLAB == 0 */
+		char dlm;	/* DLAB == 1 */
+	} u2;
+	union {
+		char rbr;	/* read only, DLAB == 0 */
+		char thr;	/* write only, DLAB == 0 */
+		char dll;	/* DLAB == 1 */
+	} u1;
+	char i4u_scr;
+	char i4u_msr;
+	char i4u_lsr;
+	char i4u_mcr;
+};
+
+/* short names */
+#define i4u_dll u1.dll
+#define i4u_ier u2.ier
+#define i4u_dlm u2.dlm
+#define i4u_fcr u3.fcr
+
+/* PCI memory space register map addressed using pci_bar0 */
+struct ioc4_memregs {
+	struct ioc4_mem {
+		/* Miscellaneous IOC4  registers */
+		uint32_t pci_err_addr_l;
+		uint32_t pci_err_addr_h;
+		uint32_t sio_ir;
+		uint32_t other_ir;
+
+		/* These registers are read-only for general kernel code.  */
+		uint32_t sio_ies_ro;
+		uint32_t other_ies_ro;
+		uint32_t sio_iec_ro;
+		uint32_t other_iec_ro;
+		uint32_t sio_cr;
+		uint32_t misc_fill1;
+		uint32_t int_out;
+		uint32_t misc_fill2;
+		uint32_t gpcr_s;
+		uint32_t gpcr_c;
+		uint32_t gpdr;
+		uint32_t misc_fill3;
+		uint32_t gppr_0;
+		uint32_t gppr_1;
+		uint32_t gppr_2;
+		uint32_t gppr_3;
+		uint32_t gppr_4;
+		uint32_t gppr_5;
+		uint32_t gppr_6;
+		uint32_t gppr_7;
+	} ioc4_mem;
+
+	char misc_fill4[0x100 - 0x5C - 4];
+
+	/* ATA/ATAP registers */
+	uint32_t ata_notused[9];
+	char ata_fill1[0x140 - 0x120 - 4];
+	uint32_t ata_notused1[8];
+	char ata_fill2[0x200 - 0x15C - 4];
+
+	/* Keyboard and mouse registers */
+	uint32_t km_notused[5];;
+	char km_fill1[0x300 - 0x210 - 4];
+
+	/* Serial port registers used for DMA serial I/O */
+	struct ioc4_serial {
+		uint32_t sbbr01_l;
+		uint32_t sbbr01_h;
+		uint32_t sbbr23_l;
+		uint32_t sbbr23_h;
+
+		struct ioc4_serialregs port_0;
+		struct ioc4_serialregs port_1;
+		struct ioc4_serialregs port_2;
+		struct ioc4_serialregs port_3;
+		struct ioc4_uartregs uart_0;
+		struct ioc4_uartregs uart_1;
+		struct ioc4_uartregs uart_2;
+		struct ioc4_uartregs uart_3;
+	} ioc4_serial;
+};
+
+/* UART clock speed */
+#define IOC4_SER_XIN_CLK        IOC4_SER_XIN_CLK_66
+#define IOC4_SER_XIN_CLK_66     66666667
+#define IOC4_SER_XIN_CLK_33     33333333
+
+#define IOC4_W_IES		0
+#define IOC4_W_IEC		1
+
+typedef void ioc4_intr_func_f(void *, uint32_t);
+typedef ioc4_intr_func_f *ioc4_intr_func_t;
+
+/* defining this will get you LOTS of great debug info */
+//#define DEBUG_INTERRUPTS
+#define DPRINT_CONFIG(_x...)	;
+//#define DPRINT_CONFIG(_x...)	printk _x
+
+/* number of characters left in xmit buffer before we ask for more */
+#define WAKEUP_CHARS	256
+
+/* number of characters we want to transmit to the lower level at a time */
+#define IOC4_MAX_CHARS	128
+
+/* Device name we're using */
+#define DEVICE_NAME	"ttyIOC"
+#define DEVICE_MAJOR 204
+#define DEVICE_MINOR 50
+
+/* register offsets */
+#define IOC4_SERIAL_OFFSET	0x300
+
+/* flags for next_char_state */
+#define NCS_BREAK	0x1
+#define NCS_PARITY	0x2
+#define NCS_FRAMING	0x4
+#define NCS_OVERRUN	0x8
+
+/* cause we need SOME parameters ... */
+#define MIN_BAUD_SUPPORTED	1200
+#define MAX_BAUD_SUPPORTED	115200
+
+/* protocol types supported */
+enum sio_proto {
+	PROTO_RS232,
+	PROTO_RS422
+};
+
+/* Notification types */
+#define N_DATA_READY	0x01
+#define N_OUTPUT_LOWAT	0x02
+#define N_BREAK		0x04
+#define N_PARITY_ERROR	0x08
+#define N_FRAMING_ERROR	0x10
+#define N_OVERRUN_ERROR	0x20
+#define N_DDCD		0x40
+#define N_DCTS		0x80
+
+#define N_ALL_INPUT	(N_DATA_READY | N_BREAK |			\
+			 N_PARITY_ERROR | N_FRAMING_ERROR |		\
+			 N_OVERRUN_ERROR | N_DDCD | N_DCTS)
+
+#define N_ALL_OUTPUT	N_OUTPUT_LOWAT
+
+#define N_ALL_ERRORS	(N_PARITY_ERROR | N_FRAMING_ERROR | N_OVERRUN_ERROR)
+
+#define N_ALL		(N_DATA_READY | N_OUTPUT_LOWAT | N_BREAK |	\
+			 N_PARITY_ERROR | N_FRAMING_ERROR |		\
+			 N_OVERRUN_ERROR | N_DDCD | N_DCTS)
+
+#define SER_DIVISOR(_x, clk)		(((clk) + (_x) * 8) / ((_x) * 16))
+#define DIVISOR_TO_BAUD(div, clk)	((clk) / 16 / (div))
+
+/* Some masks */
+#define LCR_MASK_BITS_CHAR	(UART_LCR_WLEN5 | UART_LCR_WLEN6 \
+					| UART_LCR_WLEN7 | UART_LCR_WLEN8)
+#define LCR_MASK_STOP_BITS	(UART_LCR_STOP)
+
+#define PENDING(_p)	(readl(&(_p)->ip_mem->sio_ir) & _p->ip_ienb)
+#define READ_SIO_IR(_p) readl(&(_p)->ip_mem->sio_ir)
+
+/* Default to 4k buffers */
+#ifdef IOC4_1K_BUFFERS
+#define RING_BUF_SIZE 1024
+#define IOC4_BUF_SIZE_BIT 0
+#define PROD_CONS_MASK IOC4_PROD_CONS_PTR_1K
+#else
+#define RING_BUF_SIZE 4096
+#define IOC4_BUF_SIZE_BIT IOC4_SBBR_L_SIZE
+#define PROD_CONS_MASK IOC4_PROD_CONS_PTR_4K
+#endif
+
+#define TOTAL_RING_BUF_SIZE (RING_BUF_SIZE * 4)
+
+/*
+ * This is the entry saved by the driver - one per card
+ */
+struct ioc4_control {
+	int ic_irq;
+	struct {
+		/* uart ports are allocated here */
+		struct uart_port icp_uart_port;
+		/* Handy reference material */
+		struct ioc4_port *icp_port;
+	} ic_port[IOC4_NUM_SERIAL_PORTS];
+	struct ioc4_soft *ic_soft;
+};
+
+/*
+ * per-IOC4 data structure
+ */
+#define MAX_IOC4_INTR_ENTS	(8 * sizeof(uint32_t))
+struct ioc4_soft {
+	struct ioc4_mem __iomem *is_ioc4_mem_addr;
+	struct ioc4_serial __iomem *is_ioc4_serial_addr;
+
+	/* Each interrupt type has an entry in the array */
+	struct ioc4_intr_type {
+
+		/*
+		 * Each in-use entry in this array contains at least
+		 * one nonzero bit in sd_bits; no two entries in this
+		 * array have overlapping sd_bits values.
+		 */
+		struct ioc4_intr_info {
+			uint32_t sd_bits;
+			ioc4_intr_func_f *sd_intr;
+			void *sd_info;
+		} is_intr_info[MAX_IOC4_INTR_ENTS];
+
+		/* Number of entries active in the above array */
+		atomic_t is_num_intrs;
+	} is_intr_type[IOC4_NUM_INTR_TYPES];
+
+	/* is_ir_lock must be held while
+	 * modifying sio_ie values, so
+	 * we can be sure that sio_ie is
+	 * not changing when we read it
+	 * along with sio_ir.
+	 */
+	spinlock_t is_ir_lock;	/* SIO_IE[SC] mod lock */
+};
+
+/* Local port info for each IOC4 serial ports */
+struct ioc4_port {
+	struct uart_port *ip_port;
+	/* Back ptrs for this port */
+	struct ioc4_control *ip_control;
+	struct pci_dev *ip_pdev;
+	struct ioc4_soft *ip_ioc4_soft;
+
+	/* pci mem addresses */
+	struct ioc4_mem __iomem *ip_mem;
+	struct ioc4_serial __iomem *ip_serial;
+	struct ioc4_serialregs __iomem *ip_serial_regs;
+	struct ioc4_uartregs __iomem *ip_uart_regs;
+
+	/* Ring buffer page for this port */
+	dma_addr_t ip_dma_ringbuf;
+	/* vaddr of ring buffer */
+	struct ring_buffer *ip_cpu_ringbuf;
+
+	/* Rings for this port */
+	struct ring *ip_inring;
+	struct ring *ip_outring;
+
+	/* Hook to port specific values */
+	struct hooks *ip_hooks;
+
+	spinlock_t ip_lock;
+
+	/* Various rx/tx parameters */
+	int ip_baud;
+	int ip_tx_lowat;
+	int ip_rx_timeout;
+
+	/* Copy of notification bits */
+	int ip_notify;
+
+	/* Shadow copies of various registers so we don't need to PIO
+	 * read them constantly
+	 */
+	uint32_t ip_ienb;	/* Enabled interrupts */
+	uint32_t ip_sscr;
+	uint32_t ip_tx_prod;
+	uint32_t ip_rx_cons;
+	int ip_pci_bus_speed;
+	unsigned char ip_flags;
+};
+
+/* tx low water mark.  We need to notify the driver whenever tx is getting
+ * close to empty so it can refill the tx buffer and keep things going.
+ * Let's assume that if we interrupt 1 ms before the tx goes idle, we'll
+ * have no trouble getting in more chars in time (I certainly hope so).
+ */
+#define TX_LOWAT_LATENCY      1000
+#define TX_LOWAT_HZ          (1000000 / TX_LOWAT_LATENCY)
+#define TX_LOWAT_CHARS(baud) (baud / 10 / TX_LOWAT_HZ)
+
+/* Flags per port */
+#define INPUT_HIGH	0x01
+#define DCD_ON		0x02
+#define LOWAT_WRITTEN	0x04
+#define READ_ABORTED	0x08
+
+/* Since each port has different register offsets and bitmasks
+ * for everything, we'll store those that we need in tables so we
+ * don't have to be constantly checking the port we are dealing with.
+ */
+struct hooks {
+	uint32_t intr_delta_dcd;
+	uint32_t intr_delta_cts;
+	uint32_t intr_tx_mt;
+	uint32_t intr_rx_timer;
+	uint32_t intr_rx_high;
+	uint32_t intr_tx_explicit;
+	uint32_t intr_dma_error;
+	uint32_t intr_clear;
+	uint32_t intr_all;
+	char rs422_select_pin;
+};
+
+static struct hooks hooks_array[IOC4_NUM_SERIAL_PORTS] = {
+	/* Values for port 0 */
+	{
+	 IOC4_SIO_IR_S0_DELTA_DCD, IOC4_SIO_IR_S0_DELTA_CTS,
+	 IOC4_SIO_IR_S0_TX_MT, IOC4_SIO_IR_S0_RX_TIMER,
+	 IOC4_SIO_IR_S0_RX_HIGH, IOC4_SIO_IR_S0_TX_EXPLICIT,
+	 IOC4_OTHER_IR_S0_MEMERR,
+	 (IOC4_SIO_IR_S0_TX_MT | IOC4_SIO_IR_S0_RX_FULL |
+	  IOC4_SIO_IR_S0_RX_HIGH | IOC4_SIO_IR_S0_RX_TIMER |
+	  IOC4_SIO_IR_S0_DELTA_DCD | IOC4_SIO_IR_S0_DELTA_CTS |
+	  IOC4_SIO_IR_S0_INT | IOC4_SIO_IR_S0_TX_EXPLICIT),
+	 IOC4_SIO_IR_S0, IOC4_GPPR_UART0_MODESEL_PIN,
+	 },
+
+	/* Values for port 1 */
+	{
+	 IOC4_SIO_IR_S1_DELTA_DCD, IOC4_SIO_IR_S1_DELTA_CTS,
+	 IOC4_SIO_IR_S1_TX_MT, IOC4_SIO_IR_S1_RX_TIMER,
+	 IOC4_SIO_IR_S1_RX_HIGH, IOC4_SIO_IR_S1_TX_EXPLICIT,
+	 IOC4_OTHER_IR_S1_MEMERR,
+	 (IOC4_SIO_IR_S1_TX_MT | IOC4_SIO_IR_S1_RX_FULL |
+	  IOC4_SIO_IR_S1_RX_HIGH | IOC4_SIO_IR_S1_RX_TIMER |
+	  IOC4_SIO_IR_S1_DELTA_DCD | IOC4_SIO_IR_S1_DELTA_CTS |
+	  IOC4_SIO_IR_S1_INT | IOC4_SIO_IR_S1_TX_EXPLICIT),
+	 IOC4_SIO_IR_S1, IOC4_GPPR_UART1_MODESEL_PIN,
+	 },
+
+	/* Values for port 2 */
+	{
+	 IOC4_SIO_IR_S2_DELTA_DCD, IOC4_SIO_IR_S2_DELTA_CTS,
+	 IOC4_SIO_IR_S2_TX_MT, IOC4_SIO_IR_S2_RX_TIMER,
+	 IOC4_SIO_IR_S2_RX_HIGH, IOC4_SIO_IR_S2_TX_EXPLICIT,
+	 IOC4_OTHER_IR_S2_MEMERR,
+	 (IOC4_SIO_IR_S2_TX_MT | IOC4_SIO_IR_S2_RX_FULL |
+	  IOC4_SIO_IR_S2_RX_HIGH | IOC4_SIO_IR_S2_RX_TIMER |
+	  IOC4_SIO_IR_S2_DELTA_DCD | IOC4_SIO_IR_S2_DELTA_CTS |
+	  IOC4_SIO_IR_S2_INT | IOC4_SIO_IR_S2_TX_EXPLICIT),
+	 IOC4_SIO_IR_S2, IOC4_GPPR_UART2_MODESEL_PIN,
+	 },
+
+	/* Values for port 3 */
+	{
+	 IOC4_SIO_IR_S3_DELTA_DCD, IOC4_SIO_IR_S3_DELTA_CTS,
+	 IOC4_SIO_IR_S3_TX_MT, IOC4_SIO_IR_S3_RX_TIMER,
+	 IOC4_SIO_IR_S3_RX_HIGH, IOC4_SIO_IR_S3_TX_EXPLICIT,
+	 IOC4_OTHER_IR_S3_MEMERR,
+	 (IOC4_SIO_IR_S3_TX_MT | IOC4_SIO_IR_S3_RX_FULL |
+	  IOC4_SIO_IR_S3_RX_HIGH | IOC4_SIO_IR_S3_RX_TIMER |
+	  IOC4_SIO_IR_S3_DELTA_DCD | IOC4_SIO_IR_S3_DELTA_CTS |
+	  IOC4_SIO_IR_S3_INT | IOC4_SIO_IR_S3_TX_EXPLICIT),
+	 IOC4_SIO_IR_S3, IOC4_GPPR_UART3_MODESEL_PIN,
+	 }
+};
+
+/* A ring buffer entry */
+struct ring_entry {
+	union {
+		struct {
+			uint32_t alldata;
+			uint32_t allsc;
+		} all;
+		struct {
+			char data[4];	/* data bytes */
+			char sc[4];	/* status/control */
+		} s;
+	} u;
+};
+
+/* Test the valid bits in any of the 4 sc chars using "allsc" member */
+#define RING_ANY_VALID \
+	((uint32_t)(IOC4_RXSB_MODEM_VALID | IOC4_RXSB_DATA_VALID) * 0x01010101)
+
+#define ring_sc     u.s.sc
+#define ring_data   u.s.data
+#define ring_allsc  u.all.allsc
+
+/* Number of entries per ring buffer. */
+#define ENTRIES_PER_RING (RING_BUF_SIZE / (int) sizeof(struct ring_entry))
+
+/* An individual ring */
+struct ring {
+	struct ring_entry entries[ENTRIES_PER_RING];
+};
+
+/* The whole enchilada */
+struct ring_buffer {
+	struct ring TX_0_OR_2;
+	struct ring RX_0_OR_2;
+	struct ring TX_1_OR_3;
+	struct ring RX_1_OR_3;
+};
+
+/* Get a ring from a port struct */
+#define RING(_p, _wh)	&(((struct ring_buffer *)((_p)->ip_cpu_ringbuf))->_wh)
+
+/* Infinite loop detection.
+ */
+#define MAXITER 10000000
+
+/* Prototypes */
+static void receive_chars(struct uart_port *);
+static void handle_intr(void *arg, uint32_t sio_ir);
+
+/**
+ * write_ireg - write the interrupt regs
+ * @ioc4_soft: ptr to soft struct for this port
+ * @val: value to write
+ * @which: which register
+ * @type: which ireg set
+ */
+static inline void
+write_ireg(struct ioc4_soft *ioc4_soft, uint32_t val, int which, int type)
+{
+	struct ioc4_mem __iomem *mem = ioc4_soft->is_ioc4_mem_addr;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ioc4_soft->is_ir_lock, flags);
+
+	switch (type) {
+	case IOC4_SIO_INTR_TYPE:
+		switch (which) {
+		case IOC4_W_IES:
+			writel(val, &mem->sio_ies_ro);
+			break;
+
+		case IOC4_W_IEC:
+			writel(val, &mem->sio_iec_ro);
+			break;
+		}
+		break;
+
+	case IOC4_OTHER_INTR_TYPE:
+		switch (which) {
+		case IOC4_W_IES:
+			writel(val, &mem->other_ies_ro);
+			break;
+
+		case IOC4_W_IEC:
+			writel(val, &mem->other_iec_ro);
+			break;
+		}
+		break;
+
+	default:
+		break;
+	}
+	spin_unlock_irqrestore(&ioc4_soft->is_ir_lock, flags);
+}
+
+/**
+ * set_baud - Baud rate setting code
+ * @port: port to set
+ * @baud: baud rate to use
+ */
+static int set_baud(struct ioc4_port *port, int baud)
+{
+	int actual_baud;
+	int diff;
+	int lcr;
+	unsigned short divisor;
+	struct ioc4_uartregs __iomem *uart;
+
+	divisor = SER_DIVISOR(baud, port->ip_pci_bus_speed);
+	if (!divisor)
+		return 1;
+	actual_baud = DIVISOR_TO_BAUD(divisor, port->ip_pci_bus_speed);
+
+	diff = actual_baud - baud;
+	if (diff < 0)
+		diff = -diff;
+
+	/* If we're within 1%, we've found a match */
+	if (diff * 100 > actual_baud)
+		return 1;
+
+	uart = port->ip_uart_regs;
+	lcr = readb(&uart->i4u_lcr);
+	writeb(lcr | UART_LCR_DLAB, &uart->i4u_lcr);
+	writeb((unsigned char)divisor, &uart->i4u_dll);
+	writeb((unsigned char)(divisor >> 8), &uart->i4u_dlm);
+	writeb(lcr, &uart->i4u_lcr);
+	return 0;
+}
+
+
+/**
+ * get_ioc4_port - given a uart port, return the control structure
+ * @port: uart port
+ */
+static struct ioc4_port *get_ioc4_port(struct uart_port *the_port)
+{
+	struct ioc4_control *control = dev_get_drvdata(the_port->dev);
+	int ii;
+
+	if (control) {
+		for ( ii = 0; ii < IOC4_NUM_SERIAL_PORTS; ii++ ) {
+			if (!control->ic_port[ii].icp_port)
+				continue;
+			if (the_port == control->ic_port[ii].icp_port->ip_port)
+				return control->ic_port[ii].icp_port;
+		}
+	}
+	return NULL;
+}
+
+/* The IOC4 hardware provides no atomic way to determine if interrupts
+ * are pending since two reads are required to do so.  The handler must
+ * read the SIO_IR and the SIO_IES, and take the logical and of the
+ * two.  When this value is zero, all interrupts have been serviced and
+ * the handler may return.
+ *
+ * This has the unfortunate "hole" that, if some other CPU or
+ * some other thread or some higher level interrupt manages to
+ * modify SIO_IE between our reads of SIO_IR and SIO_IE, we may
+ * think we have observed SIO_IR&SIO_IE==0 when in fact this
+ * condition never really occurred.
+ *
+ * To solve this, we use a simple spinlock that must be held
+ * whenever modifying SIO_IE; holding this lock while observing
+ * both SIO_IR and SIO_IE guarantees that we do not falsely
+ * conclude that no enabled interrupts are pending.
+ */
+
+static inline uint32_t
+pending_intrs(struct ioc4_soft *soft, int type)
+{
+	struct ioc4_mem __iomem *mem = soft->is_ioc4_mem_addr;
+	unsigned long flag;
+	uint32_t intrs = 0;
+
+	BUG_ON(!((type == IOC4_SIO_INTR_TYPE)
+	       || (type == IOC4_OTHER_INTR_TYPE)));
+
+	spin_lock_irqsave(&soft->is_ir_lock, flag);
+
+	switch (type) {
+	case IOC4_SIO_INTR_TYPE:
+		intrs = readl(&mem->sio_ir) & readl(&mem->sio_ies_ro);
+		break;
+
+	case IOC4_OTHER_INTR_TYPE:
+		intrs = readl(&mem->other_ir) & readl(&mem->other_ies_ro);
+
+		/* Don't process any ATA interrupte */
+		intrs &= ~(IOC4_OTHER_IR_ATA_INT | IOC4_OTHER_IR_ATA_MEMERR);
+		break;
+
+	default:
+		break;
+	}
+	spin_unlock_irqrestore(&soft->is_ir_lock, flag);
+	return intrs;
+}
+
+/**
+ * port_init - Initialize the sio and ioc4 hardware for a given port
+ *			called per port from attach...
+ * @port: port to initialize
+ */
+static int inline port_init(struct ioc4_port *port)
+{
+	uint32_t sio_cr;
+	struct hooks *hooks = port->ip_hooks;
+	struct ioc4_uartregs __iomem *uart;
+
+	/* Idle the IOC4 serial interface */
+	writel(IOC4_SSCR_RESET, &port->ip_serial_regs->sscr);
+
+	/* Wait until any pending bus activity for this port has ceased */
+	do
+		sio_cr = readl(&port->ip_mem->sio_cr);
+	while (!(sio_cr & IOC4_SIO_CR_SIO_DIAG_IDLE));
+
+	/* Finish reset sequence */
+	writel(0, &port->ip_serial_regs->sscr);
+
+	/* Once RESET is done, reload cached tx_prod and rx_cons values
+	 * and set rings to empty by making prod == cons
+	 */
+	port->ip_tx_prod = readl(&port->ip_serial_regs->stcir) & PROD_CONS_MASK;
+	writel(port->ip_tx_prod, &port->ip_serial_regs->stpir);
+	port->ip_rx_cons = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
+	writel(port->ip_rx_cons, &port->ip_serial_regs->srcir);
+
+	/* Disable interrupts for this 16550 */
+	uart = port->ip_uart_regs;
+	writeb(0, &uart->i4u_lcr);
+	writeb(0, &uart->i4u_ier);
+
+	/* Set the default baud */
+	set_baud(port, port->ip_baud);
+
+	/* Set line control to 8 bits no parity */
+	writeb(UART_LCR_WLEN8 | 0, &uart->i4u_lcr);
+					/* UART_LCR_STOP == 1 stop */
+
+	/* Enable the FIFOs */
+	writeb(UART_FCR_ENABLE_FIFO, &uart->i4u_fcr);
+	/* then reset 16550 FIFOs */
+	writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
+			&uart->i4u_fcr);
+
+	/* Clear modem control register */
+	writeb(0, &uart->i4u_mcr);
+
+	/* Clear deltas in modem status register */
+	readb(&uart->i4u_msr);
+
+	/* Only do this once per port pair */
+	if (port->ip_hooks == &hooks_array[0]
+			    || port->ip_hooks == &hooks_array[2]) {
+		unsigned long ring_pci_addr;
+		uint32_t __iomem *sbbr_l;
+		uint32_t __iomem *sbbr_h;
+
+		if (port->ip_hooks == &hooks_array[0]) {
+			sbbr_l = &port->ip_serial->sbbr01_l;
+			sbbr_h = &port->ip_serial->sbbr01_h;
+		} else {
+			sbbr_l = &port->ip_serial->sbbr23_l;
+			sbbr_h = &port->ip_serial->sbbr23_h;
+		}
+
+		ring_pci_addr = (unsigned long __iomem)port->ip_dma_ringbuf;
+		DPRINT_CONFIG(("%s: ring_pci_addr 0x%lx\n",
+					__FUNCTION__, ring_pci_addr));
+
+		writel((unsigned int)((uint64_t)ring_pci_addr >> 32), sbbr_h);
+		writel((unsigned int)ring_pci_addr | IOC4_BUF_SIZE_BIT, sbbr_l);
+	}
+
+	/* Set the receive timeout value to 10 msec */
+	writel(IOC4_SRTR_HZ / 100, &port->ip_serial_regs->srtr);
+
+	/* Set rx threshold, enable DMA */
+	/* Set high water mark at 3/4 of full ring */
+	port->ip_sscr = (ENTRIES_PER_RING * 3 / 4);
+	writel(port->ip_sscr, &port->ip_serial_regs->sscr);
+
+	/* Disable and clear all serial related interrupt bits */
+	write_ireg(port->ip_ioc4_soft, hooks->intr_clear,
+		       IOC4_W_IEC, IOC4_SIO_INTR_TYPE);
+	port->ip_ienb &= ~hooks->intr_clear;
+	writel(hooks->intr_clear, &port->ip_mem->sio_ir);
+	return 0;
+}
+
+/**
+ * handle_dma_error_intr - service any pending DMA error interrupts for the
+ *			given port - 2nd level called via sd_intr
+ * @arg: handler arg
+ * @other_ir: ioc4regs
+ */
+static void handle_dma_error_intr(void *arg, uint32_t other_ir)
+{
+	struct ioc4_port *port = (struct ioc4_port *)arg;
+	struct hooks *hooks = port->ip_hooks;
+	unsigned int flags;
+
+	spin_lock_irqsave(&port->ip_lock, flags);
+
+	/* ACK the interrupt */
+	writel(hooks->intr_dma_error, &port->ip_mem->other_ir);
+
+	if (readl(&port->ip_mem->pci_err_addr_l) & IOC4_PCI_ERR_ADDR_VLD) {
+		printk(KERN_ERR
+			"PCI error address is 0x%lx, "
+				"master is serial port %c %s\n",
+		     (((uint64_t)readl(&port->ip_mem->pci_err_addr_h)
+							 << 32)
+				| readl(&port->ip_mem->pci_err_addr_l))
+					& IOC4_PCI_ERR_ADDR_ADDR_MSK, '1' +
+		     ((char)(readl(&port->ip_mem-> pci_err_addr_l) &
+			     IOC4_PCI_ERR_ADDR_MST_NUM_MSK) >> 1),
+		     (readl(&port->ip_mem->pci_err_addr_l)
+				& IOC4_PCI_ERR_ADDR_MST_TYP_MSK)
+				? "RX" : "TX");
+
+		if (readl(&port->ip_mem->pci_err_addr_l)
+						& IOC4_PCI_ERR_ADDR_MUL_ERR) {
+			printk(KERN_ERR
+				"Multiple errors occurred\n");
+		}
+	}
+	spin_unlock_irqrestore(&port->ip_lock, flags);
+
+	/* Re-enable DMA error interrupts */
+	write_ireg(port->ip_ioc4_soft, hooks->intr_dma_error, IOC4_W_IES,
+						IOC4_OTHER_INTR_TYPE);
+}
+
+/**
+ * intr_connect - interrupt connect function
+ * @soft: soft struct for this card
+ * @type: interrupt type
+ * @intrbits: bit pattern to set
+ * @intr: handler function
+ * @info: handler arg
+ */
+static void
+intr_connect(struct ioc4_soft *soft, int type,
+		  uint32_t intrbits, ioc4_intr_func_f * intr, void *info)
+{
+	int i;
+	struct ioc4_intr_info *intr_ptr;
+
+	BUG_ON(!((type == IOC4_SIO_INTR_TYPE)
+	       || (type == IOC4_OTHER_INTR_TYPE)));
+
+	i = atomic_inc(&soft-> is_intr_type[type].is_num_intrs) - 1;
+	BUG_ON(!(i < MAX_IOC4_INTR_ENTS || (printk("i %d\n", i), 0)));
+
+	/* Save off the lower level interrupt handler */
+	intr_ptr = &soft->is_intr_type[type].is_intr_info[i];
+	intr_ptr->sd_bits = intrbits;
+	intr_ptr->sd_intr = intr;
+	intr_ptr->sd_info = info;
+}
+
+/**
+ * ioc4_intr - Top level IOC4 interrupt handler.
+ * @irq: irq value
+ * @arg: handler arg
+ * @regs: registers
+ */
+static irqreturn_t ioc4_intr(int irq, void *arg, struct pt_regs *regs)
+{
+	struct ioc4_soft *soft;
+	uint32_t this_ir, this_mir;
+	int xx, num_intrs = 0;
+	int intr_type;
+	int handled = 0;
+	struct ioc4_intr_info *ii;
+
+	soft = arg;
+	for (intr_type = 0; intr_type < IOC4_NUM_INTR_TYPES; intr_type++) {
+		num_intrs = (int)atomic_read(
+				&soft->is_intr_type[intr_type].is_num_intrs);
+
+		this_mir = this_ir = pending_intrs(soft, intr_type);
+
+		/* Farm out the interrupt to the various drivers depending on
+		 * which interrupt bits are set.
+		 */
+		for (xx = 0; xx < num_intrs; xx++) {
+			ii = &soft->is_intr_type[intr_type].is_intr_info[xx];
+			if ((this_mir = this_ir & ii->sd_bits)) {
+				/* Disable owned interrupts, call handler */
+				handled++;
+				write_ireg(soft, ii->sd_bits, IOC4_W_IEC,
+								intr_type);
+				ii->sd_intr(ii->sd_info, this_mir);
+				this_ir &= ~this_mir;
+			}
+		}
+		if (this_ir) {
+			printk(KERN_ERR
+			       "unknown IOC4 %s interrupt 0x%x, sio_ir = 0x%x,"
+				" sio_ies = 0x%x, other_ir = 0x%x :"
+				"other_ies = 0x%x\n",
+			       (intr_type == IOC4_SIO_INTR_TYPE) ? "sio" :
+			       "other", this_ir,
+			       readl(&soft->is_ioc4_mem_addr->sio_ir),
+			       readl(&soft->is_ioc4_mem_addr->sio_ies_ro),
+			       readl(&soft->is_ioc4_mem_addr->other_ir),
+			       readl(&soft->is_ioc4_mem_addr->other_ies_ro));
+		}
+	}
+#ifdef DEBUG_INTERRUPTS
+	{
+		struct ioc4_mem __iomem *mem = soft->is_ioc4_mem_addr;
+		spinlock_t *lp = &soft->is_ir_lock;
+		unsigned long flag;
+
+		spin_lock_irqsave(&soft->is_ir_lock, flag);
+		printk ("%s : %d : mem 0x%p sio_ir 0x%x sio_ies_ro 0x%x "
+				"other_ir 0x%x other_ies_ro 0x%x mask 0x%x\n",
+		     __FUNCTION__, __LINE__,
+		     (void *)mem, readl(&mem->sio_ir),
+		     readl(&mem->sio_ies_ro),
+		     readl(&mem->other_ir),
+		     readl(&mem->other_ies_ro),
+		     IOC4_OTHER_IR_ATA_INT | IOC4_OTHER_IR_ATA_MEMERR);
+		spin_unlock_irqrestore(&soft->is_ir_lock, flag);
+	}
+#endif
+	return handled ? IRQ_HANDLED : IRQ_NONE;
+}
+
+/**
+ * ioc4_attach_local - Device initialization.
+ *			Called at *_attach() time for each
+ *			IOC4 with serial ports in the system.
+ * @control: ioc4_control ptr
+ * @pdev: PCI handle for this device
+ * @soft: soft struct for this device
+ * @ioc4: ioc4 mem space
+ */
+static int inline ioc4_attach_local(struct pci_dev *pdev,
+			struct ioc4_control *control,
+			struct ioc4_soft *soft, void __iomem *ioc4_mem,
+			void __iomem *ioc4_serial)
+{
+	struct ioc4_port *port;
+	struct ioc4_port *ports[IOC4_NUM_SERIAL_PORTS];
+	int port_number;
+	uint16_t ioc4_revid_min = 62;
+	uint16_t ioc4_revid;
+
+	/* IOC4 firmware must be at least rev 62 */
+	pci_read_config_word(pdev, PCI_COMMAND_SPECIAL, &ioc4_revid);
+
+	printk(K