tty: move drivers/serial/ to drivers/tty/serial/

The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.

This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 0 insertions, 327 deletions

diff --git a/drivers/serial/8250_hp300.c b/drivers/serial/8250_hp300.c
deleted file mode 100644
index c13438c9301..00000000000
--- a/drivers/serial/8250_hp300.c
+++ /dev/null
@@ -1,327 +0,0 @@
-/*
- * Driver for the 98626/98644/internal serial interface on hp300/hp400
- * (based on the National Semiconductor INS8250/NS16550AF/WD16C552 UARTs)
- *
- * Ported from 2.2 and modified to use the normal 8250 driver
- * by Kars de Jong <jongk@linux-m68k.org>, May 2004.
- */
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/string.h>
-#include <linux/kernel.h>
-#include <linux/serial.h>
-#include <linux/serial_core.h>
-#include <linux/serial_8250.h>
-#include <linux/delay.h>
-#include <linux/dio.h>
-#include <linux/console.h>
-#include <linux/slab.h>
-#include <asm/io.h>
-
-#include "8250.h"
-
-#if !defined(CONFIG_HPDCA) && !defined(CONFIG_HPAPCI)
-#warning CONFIG_8250 defined but neither CONFIG_HPDCA nor CONFIG_HPAPCI defined, are you sure?
-#endif
-
-#ifdef CONFIG_HPAPCI
-struct hp300_port
-{
-	struct hp300_port *next;	/* next port */
-	int line;			/* line (tty) number */
-};
-
-static struct hp300_port *hp300_ports;
-#endif
-
-#ifdef CONFIG_HPDCA
-
-static int __devinit hpdca_init_one(struct dio_dev *d,
-					const struct dio_device_id *ent);
-static void __devexit hpdca_remove_one(struct dio_dev *d);
-
-static struct dio_device_id hpdca_dio_tbl[] = {
-	{ DIO_ID_DCA0 },
-	{ DIO_ID_DCA0REM },
-	{ DIO_ID_DCA1 },
-	{ DIO_ID_DCA1REM },
-	{ 0 }
-};
-
-static struct dio_driver hpdca_driver = {
-	.name      = "hpdca",
-	.id_table  = hpdca_dio_tbl,
-	.probe     = hpdca_init_one,
-	.remove    = __devexit_p(hpdca_remove_one),
-};
-
-#endif
-
-static unsigned int num_ports;
-
-extern int hp300_uart_scode;
-
-/* Offset to UART registers from base of DCA */
-#define UART_OFFSET	17
-
-#define DCA_ID		0x01	/* ID (read), reset (write) */
-#define DCA_IC		0x03	/* Interrupt control        */
-
-/* Interrupt control */
-#define DCA_IC_IE	0x80	/* Master interrupt enable  */
-
-#define HPDCA_BAUD_BASE 153600
-
-/* Base address of the Frodo part */
-#define FRODO_BASE	(0x41c000)
-
-/*
- * Where we find the 8250-like APCI ports, and how far apart they are.
- */
-#define FRODO_APCIBASE		0x0
-#define FRODO_APCISPACE		0x20
-#define FRODO_APCI_OFFSET(x)	(FRODO_APCIBASE + ((x) * FRODO_APCISPACE))
-
-#define HPAPCI_BAUD_BASE 500400
-
-#ifdef CONFIG_SERIAL_8250_CONSOLE
-/*
- * Parse the bootinfo to find descriptions for headless console and
- * debug serial ports and register them with the 8250 driver.
- * This function should be called before serial_console_init() is called
- * to make sure the serial console will be available for use. IA-64 kernel
- * calls this function from setup_arch() after the EFI and ACPI tables have
- * been parsed.
- */
-int __init hp300_setup_serial_console(void)
-{
-	int scode;
-	struct uart_port port;
-
-	memset(&port, 0, sizeof(port));
-
-	if (hp300_uart_scode < 0 || hp300_uart_scode > DIO_SCMAX)
-		return 0;
-
-	if (DIO_SCINHOLE(hp300_uart_scode))
-		return 0;
-
-	scode = hp300_uart_scode;
-
-	/* Memory mapped I/O */
-	port.iotype = UPIO_MEM;
-	port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
-	port.type = PORT_UNKNOWN;
-
-	/* Check for APCI console */
-	if (scode == 256) {
-#ifdef CONFIG_HPAPCI
-		printk(KERN_INFO "Serial console is HP APCI 1\n");
-
-		port.uartclk = HPAPCI_BAUD_BASE * 16;
-		port.mapbase = (FRODO_BASE + FRODO_APCI_OFFSET(1));
-		port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
-		port.regshift = 2;
-		add_preferred_console("ttyS", port.line, "9600n8");
-#else
-		printk(KERN_WARNING "Serial console is APCI but support is disabled (CONFIG_HPAPCI)!\n");
-		return 0;
-#endif
-	} else {
-#ifdef CONFIG_HPDCA
-		unsigned long pa = dio_scodetophysaddr(scode);
-		if (!pa)
-			return 0;
-
-		printk(KERN_INFO "Serial console is HP DCA at select code %d\n", scode);
-
-		port.uartclk = HPDCA_BAUD_BASE * 16;
-		port.mapbase = (pa + UART_OFFSET);
-		port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
-		port.regshift = 1;
-		port.irq = DIO_IPL(pa + DIO_VIRADDRBASE);
-
-		/* Enable board-interrupts */
-		out_8(pa + DIO_VIRADDRBASE + DCA_IC, DCA_IC_IE);
-
-		if (DIO_ID(pa + DIO_VIRADDRBASE) & 0x80)
-			add_preferred_console("ttyS", port.line, "9600n8");
-#else
-		printk(KERN_WARNING "Serial console is DCA but support is disabled (CONFIG_HPDCA)!\n");
-		return 0;
-#endif
-	}
-
-	if (early_serial_setup(&port) < 0)
-		printk(KERN_WARNING "hp300_setup_serial_console(): early_serial_setup() failed.\n");
-	return 0;
-}
-#endif /* CONFIG_SERIAL_8250_CONSOLE */
-
-#ifdef CONFIG_HPDCA
-static int __devinit hpdca_init_one(struct dio_dev *d,
-				const struct dio_device_id *ent)
-{
-	struct uart_port port;
-	int line;
-
-#ifdef CONFIG_SERIAL_8250_CONSOLE
-	if (hp300_uart_scode == d->scode) {
-		/* Already got it. */
-		return 0;
-	}
-#endif
-	memset(&port, 0, sizeof(struct uart_port));
-
-	/* Memory mapped I/O */
-	port.iotype = UPIO_MEM;
-	port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
-	port.irq = d->ipl;
-	port.uartclk = HPDCA_BAUD_BASE * 16;
-	port.mapbase = (d->resource.start + UART_OFFSET);
-	port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
-	port.regshift = 1;
-	port.dev = &d->dev;
-	line = serial8250_register_port(&port);
-
-	if (line < 0) {
-		printk(KERN_NOTICE "8250_hp300: register_serial() DCA scode %d"
-		       " irq %d failed\n", d->scode, port.irq);
-		return -ENOMEM;
-	}
-
-	/* Enable board-interrupts */
-	out_8(d->resource.start + DIO_VIRADDRBASE + DCA_IC, DCA_IC_IE);
-	dio_set_drvdata(d, (void *)line);
-
-	/* Reset the DCA */
-	out_8(d->resource.start + DIO_VIRADDRBASE + DCA_ID, 0xff);
-	udelay(100);
-
-	num_ports++;
-
-	return 0;
-}
-#endif
-
-static int __init hp300_8250_init(void)
-{
-	static int called;
-#ifdef CONFIG_HPAPCI
-	int line;
-	unsigned long base;
-	struct uart_port uport;
-	struct hp300_port *port;
-	int i;
-#endif
-	if (called)
-		return -ENODEV;
-	called = 1;
-
-	if (!MACH_IS_HP300)
-		return -ENODEV;
-
-#ifdef CONFIG_HPDCA
-	dio_register_driver(&hpdca_driver);
-#endif
-#ifdef CONFIG_HPAPCI
-	if (hp300_model < HP_400) {
-		if (!num_ports)
-			return -ENODEV;
-		return 0;
-	}
-	/* These models have the Frodo chip.
-	 * Port 0 is reserved for the Apollo Domain keyboard.
-	 * Port 1 is either the console or the DCA.
-	 */
-	for (i = 1; i < 4; i++) {
-		/* Port 1 is the console on a 425e, on other machines it's
-		 * mapped to DCA.
-		 */
-#ifdef CONFIG_SERIAL_8250_CONSOLE
-		if (i == 1)
-			continue;
-#endif
-
-		/* Create new serial device */
-		port = kmalloc(sizeof(struct hp300_port), GFP_KERNEL);
-		if (!port)
-			return -ENOMEM;
-
-		memset(&uport, 0, sizeof(struct uart_port));
-
-		base = (FRODO_BASE + FRODO_APCI_OFFSET(i));
-
-		/* Memory mapped I/O */
-		uport.iotype = UPIO_MEM;
-		uport.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ \
-			      | UPF_BOOT_AUTOCONF;
-		/* XXX - no interrupt support yet */
-		uport.irq = 0;
-		uport.uartclk = HPAPCI_BAUD_BASE * 16;
-		uport.mapbase = base;
-		uport.membase = (char *)(base + DIO_VIRADDRBASE);
-		uport.regshift = 2;
-
-		line = serial8250_register_port(&uport);
-
-		if (line < 0) {
-			printk(KERN_NOTICE "8250_hp300: register_serial() APCI"
-			       " %d irq %d failed\n", i, uport.irq);
-			kfree(port);
-			continue;
-		}
-
-		port->line = line;
-		port->next = hp300_ports;
-		hp300_ports = port;
-
-		num_ports++;
-	}
-#endif
-
-	/* Any boards found? */
-	if (!num_ports)
-		return -ENODEV;
-
-	return 0;
-}
-
-#ifdef CONFIG_HPDCA
-static void __devexit hpdca_remove_one(struct dio_dev *d)
-{
-	int line;
-
-	line = (int) dio_get_drvdata(d);
-	if (d->resource.start) {
-		/* Disable board-interrupts */
-		out_8(d->resource.start + DIO_VIRADDRBASE + DCA_IC, 0);
-	}
-	serial8250_unregister_port(line);
-}
-#endif
-
-static void __exit hp300_8250_exit(void)
-{
-#ifdef CONFIG_HPAPCI
-	struct hp300_port *port, *to_free;
-
-	for (port = hp300_ports; port; ) {
-		serial8250_unregister_port(port->line);
-		to_free = port;
-		port = port->next;
-		kfree(to_free);
-	}
-
-	hp300_ports = NULL;
-#endif
-#ifdef CONFIG_HPDCA
-	dio_unregister_driver(&hpdca_driver);
-#endif
-}
-
-module_init(hp300_8250_init);
-module_exit(hp300_8250_exit);
-MODULE_DESCRIPTION("HP DCA/APCI serial driver");
-MODULE_AUTHOR("Kars de Jong <jongk@linux-m68k.org>");
-MODULE_LICENSE("GPL");