Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 565 insertions, 0 deletions

diff --git a/drivers/scsi/tmscsim.h b/drivers/scsi/tmscsim.h
new file mode 100644
index 00000000000..d4495272fb4
--- /dev/null
+++ b/drivers/scsi/tmscsim.h
@@ -0,0 +1,565 @@
+/***********************************************************************
+;*	File Name : TMSCSIM.H					       *
+;*		    TEKRAM DC-390(T) PCI SCSI Bus Master Host Adapter  *
+;*		    Device Driver				       *
+;***********************************************************************/
+/* $Id: tmscsim.h,v 2.15.2.3 2000/11/17 20:52:27 garloff Exp $ */
+
+#ifndef _TMSCSIM_H
+#define _TMSCSIM_H
+
+#include <linux/types.h>
+#include <linux/config.h>
+
+#define SCSI_IRQ_NONE 255
+
+#define MAX_ADAPTER_NUM 	4
+#define MAX_SG_LIST_BUF 	16	/* Not used */
+#define MAX_SCSI_ID		8
+#define MAX_SRB_CNT		50	/* Max number of started commands */
+
+#define SEL_TIMEOUT		153	/* 250 ms selection timeout (@ 40 MHz) */
+
+#define pci_dma_lo32(a)			(a & 0xffffffff)
+
+typedef u8		UCHAR;	/*  8 bits */
+typedef u16		USHORT;	/* 16 bits */
+typedef u32		UINT;	/* 32 bits */
+typedef unsigned long	ULONG;	/* 32/64 bits */
+
+
+/*
+;-----------------------------------------------------------------------
+; SCSI Request Block
+;-----------------------------------------------------------------------
+*/
+struct dc390_srb
+{
+//u8		CmdBlock[12];
+
+struct dc390_srb	*pNextSRB;
+struct dc390_dcb	*pSRBDCB;
+struct scsi_cmnd	*pcmd;
+struct scatterlist	*pSegmentList;
+
+struct scatterlist Segmentx;	/* make a one entry of S/G list table */
+
+unsigned long	SGBusAddr;	/*;a segment starting address as seen by AM53C974A*/
+unsigned long	SGToBeXferLen;	/*; to be xfer length */
+unsigned long	TotalXferredLen;
+unsigned long	SavedTotXLen;
+unsigned long	Saved_Ptr;
+u32		SRBState;
+
+u8		SRBStatus;
+u8		SRBFlag;	/*; b0-AutoReqSense,b6-Read,b7-write */
+				/*; b4-settimeout,b5-Residual valid */
+u8		AdaptStatus;
+u8		TargetStatus;
+
+u8		ScsiPhase;
+s8		TagNumber;
+u8		SGIndex;
+u8		SGcount;
+
+u8		MsgCnt;
+u8		EndMessage;
+u8		SavedSGCount;			
+
+u8		MsgInBuf[6];
+u8		MsgOutBuf[6];
+
+//u8		IORBFlag;	/*;81h-Reset, 2-retry */
+};
+
+
+/*
+;-----------------------------------------------------------------------
+; Device Control Block
+;-----------------------------------------------------------------------
+*/
+struct dc390_dcb
+{
+struct dc390_dcb	*pNextDCB;
+struct dc390_acb	*pDCBACB;
+
+/* Queued SRBs */
+struct dc390_srb	*pGoingSRB;
+struct dc390_srb	*pGoingLast;
+struct dc390_srb	*pActiveSRB;
+u8		GoingSRBCnt;
+
+u32		TagMask;
+
+u8		TargetID;	/*; SCSI Target ID  (SCSI Only) */
+u8		TargetLUN;	/*; SCSI Log.  Unit (SCSI Only) */
+u8		DevMode;
+u8		DCBFlag;
+
+u8		CtrlR1;
+u8		CtrlR3;
+u8		CtrlR4;
+
+u8		SyncMode;	/*; 0:async mode */
+u8		NegoPeriod;	/*;for nego. */
+u8		SyncPeriod;	/*;for reg. */
+u8		SyncOffset;	/*;for reg. and nego.(low nibble) */
+};
+
+
+/*
+;-----------------------------------------------------------------------
+; Adapter Control Block
+;-----------------------------------------------------------------------
+*/
+struct dc390_acb
+{
+struct Scsi_Host *pScsiHost;
+u16		IOPortBase;
+u8		IRQLevel;
+u8		status;
+
+u8		SRBCount;
+u8		AdapterIndex;	/*; nth Adapter this driver */
+u8		DCBCnt;
+
+u8		TagMaxNum;
+u8		ACBFlag;
+u8		Gmode2;
+u8		scan_devices;
+
+struct dc390_dcb	*pLinkDCB;
+struct dc390_dcb	*pLastDCB;
+struct dc390_dcb	*pDCBRunRobin;
+
+struct dc390_dcb	*pActiveDCB;
+struct dc390_srb	*pFreeSRB;
+struct dc390_srb	*pTmpSRB;
+
+u8		msgin123[4];
+u8		Connected;
+u8		pad;
+
+#if defined(USE_SPINLOCKS) && USE_SPINLOCKS > 1 && (defined(CONFIG_SMP) || DEBUG_SPINLOCKS > 0)
+spinlock_t	lock;
+#endif
+u8		sel_timeout;
+u8		glitch_cfg;
+
+u8		MsgLen;
+u8		Ignore_IRQ;	/* Not used */
+
+struct pci_dev	*pdev;
+
+unsigned long	Cmds;
+u32		SelLost;
+u32		SelConn;
+u32		CmdInQ;
+u32		CmdOutOfSRB;
+
+struct dc390_srb	TmpSRB;
+struct dc390_srb	SRB_array[MAX_SRB_CNT]; 	/* 50 SRBs */
+};
+
+
+/*;-----------------------------------------------------------------------*/
+
+
+#define BIT31	0x80000000
+#define BIT30	0x40000000
+#define BIT29	0x20000000
+#define BIT28	0x10000000
+#define BIT27	0x08000000
+#define BIT26	0x04000000
+#define BIT25	0x02000000
+#define BIT24	0x01000000
+#define BIT23	0x00800000
+#define BIT22	0x00400000
+#define BIT21	0x00200000
+#define BIT20	0x00100000
+#define BIT19	0x00080000
+#define BIT18	0x00040000
+#define BIT17	0x00020000
+#define BIT16	0x00010000
+#define BIT15	0x00008000
+#define BIT14	0x00004000
+#define BIT13	0x00002000
+#define BIT12	0x00001000
+#define BIT11	0x00000800
+#define BIT10	0x00000400
+#define BIT9	0x00000200
+#define BIT8	0x00000100
+#define BIT7	0x00000080
+#define BIT6	0x00000040
+#define BIT5	0x00000020
+#define BIT4	0x00000010
+#define BIT3	0x00000008
+#define BIT2	0x00000004
+#define BIT1	0x00000002
+#define BIT0	0x00000001
+
+/*;---UnitCtrlFlag */
+#define UNIT_ALLOCATED	BIT0
+#define UNIT_INFO_CHANGED BIT1
+#define FORMATING_MEDIA BIT2
+#define UNIT_RETRY	BIT3
+
+/*;---UnitFlags */
+#define DASD_SUPPORT	BIT0
+#define SCSI_SUPPORT	BIT1
+#define ASPI_SUPPORT	BIT2
+
+/*;----SRBState machine definition */
+#define SRB_FREE	0
+#define SRB_WAIT	BIT0
+#define SRB_READY	BIT1
+#define SRB_MSGOUT	BIT2	/*;arbitration+msg_out 1st byte*/
+#define SRB_MSGIN	BIT3
+#define SRB_MSGIN_MULTI BIT4
+#define SRB_COMMAND	BIT5
+#define SRB_START_	BIT6	/*;arbitration+msg_out+command_out*/
+#define SRB_DISCONNECT	BIT7
+#define SRB_DATA_XFER	BIT8
+#define SRB_XFERPAD	BIT9
+#define SRB_STATUS	BIT10
+#define SRB_COMPLETED	BIT11
+#define SRB_ABORT_SENT	BIT12
+#define DO_SYNC_NEGO	BIT13
+#define SRB_UNEXPECT_RESEL BIT14
+
+/*;---SRBstatus */
+#define SRB_OK		BIT0
+#define ABORTION	BIT1
+#define OVER_RUN	BIT2
+#define UNDER_RUN	BIT3
+#define PARITY_ERROR	BIT4
+#define SRB_ERROR	BIT5
+
+/*;---ACBFlag */
+#define RESET_DEV	BIT0
+#define RESET_DETECT	BIT1
+#define RESET_DONE	BIT2
+
+/*;---DCBFlag */
+#define ABORT_DEV_	BIT0
+
+/*;---SRBFlag */
+#define DATAOUT 	BIT7
+#define DATAIN		BIT6
+#define RESIDUAL_VALID	BIT5
+#define ENABLE_TIMER	BIT4
+#define RESET_DEV0	BIT2
+#define ABORT_DEV	BIT1
+#define AUTO_REQSENSE	BIT0
+
+/*;---Adapter status */
+#define H_STATUS_GOOD	 0
+#define H_SEL_TIMEOUT	 0x11
+#define H_OVER_UNDER_RUN 0x12
+#define H_UNEXP_BUS_FREE 0x13
+#define H_TARGET_PHASE_F 0x14
+#define H_INVALID_CCB_OP 0x16
+#define H_LINK_CCB_BAD	 0x17
+#define H_BAD_TARGET_DIR 0x18
+#define H_DUPLICATE_CCB  0x19
+#define H_BAD_CCB_OR_SG  0x1A
+#define H_ABORT 	 0x0FF
+
+/*; SCSI Status byte codes*/ 
+/* The values defined in include/scsi/scsi.h, to be shifted << 1 */
+
+#define SCSI_STAT_UNEXP_BUS_F	0xFD	/*;  Unexpect Bus Free */
+#define SCSI_STAT_BUS_RST_DETECT 0xFE	/*;  Scsi Bus Reset detected */
+#define SCSI_STAT_SEL_TIMEOUT	0xFF	/*;  Selection Time out */
+
+/* cmd->result */
+#define RES_TARGET		0x000000FF	/* Target State */
+#define RES_TARGET_LNX		STATUS_MASK	/* Only official ... */
+#define RES_ENDMSG		0x0000FF00	/* End Message */
+#define RES_DID			0x00FF0000	/* DID_ codes */
+#define RES_DRV			0xFF000000	/* DRIVER_ codes */
+
+#define MK_RES(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt))
+#define MK_RES_LNX(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt)<<1)
+
+#define SET_RES_TARGET(who, tgt) do { who &= ~RES_TARGET; who |= (int)(tgt); } while (0)
+#define SET_RES_TARGET_LNX(who, tgt) do { who &= ~RES_TARGET_LNX; who |= (int)(tgt) << 1; } while (0)
+#define SET_RES_MSG(who, msg) do { who &= ~RES_ENDMSG; who |= (int)(msg) << 8; } while (0)
+#define SET_RES_DID(who, did) do { who &= ~RES_DID; who |= (int)(did) << 16; } while (0)
+#define SET_RES_DRV(who, drv) do { who &= ~RES_DRV; who |= (int)(drv) << 24; } while (0)
+
+/*;---Sync_Mode */
+#define SYNC_DISABLE	0
+#define SYNC_ENABLE	BIT0
+#define SYNC_NEGO_DONE	BIT1
+#define WIDE_ENABLE	BIT2	/* Not used ;-) */
+#define WIDE_NEGO_DONE	BIT3	/* Not used ;-) */
+#define EN_TAG_QUEUEING	BIT4
+#define EN_ATN_STOP	BIT5
+
+#define SYNC_NEGO_OFFSET 15
+
+/*;---SCSI bus phase*/
+#define SCSI_DATA_OUT	0
+#define SCSI_DATA_IN	1
+#define SCSI_COMMAND	2
+#define SCSI_STATUS_	3
+#define SCSI_NOP0	4
+#define SCSI_NOP1	5
+#define SCSI_MSG_OUT	6
+#define SCSI_MSG_IN	7
+
+/*;----SCSI MSG BYTE*/ /* see scsi/scsi.h */ /* One is missing ! */
+#define ABORT_TAG	0x0d
+
+/*
+ *	SISC query queue
+ */
+typedef struct {
+	dma_addr_t		saved_dma_handle;
+} dc390_cmd_scp_t;
+
+/*
+;==========================================================
+; EEPROM byte offset
+;==========================================================
+*/
+typedef  struct  _EEprom
+{
+u8	EE_MODE1;
+u8	EE_SPEED;
+u8	xx1;
+u8	xx2;
+} EEprom, *PEEprom;
+
+#define REAL_EE_ADAPT_SCSI_ID 64
+#define REAL_EE_MODE2	65
+#define REAL_EE_DELAY	66
+#define REAL_EE_TAG_CMD_NUM	67
+
+#define EE_ADAPT_SCSI_ID 32
+#define EE_MODE2	33
+#define EE_DELAY	34
+#define EE_TAG_CMD_NUM	35
+
+#define EE_LEN		40
+
+/*; EE_MODE1 bits definition*/
+#define PARITY_CHK_	BIT0
+#define SYNC_NEGO_	BIT1
+#define EN_DISCONNECT_	BIT2
+#define SEND_START_	BIT3
+#define TAG_QUEUEING_	BIT4
+
+/*; EE_MODE2 bits definition*/
+#define MORE2_DRV	BIT0
+#define GREATER_1G	BIT1
+#define RST_SCSI_BUS	BIT2
+#define ACTIVE_NEGATION BIT3
+#define NO_SEEK 	BIT4
+#define LUN_CHECK	BIT5
+
+#define ENABLE_CE	1
+#define DISABLE_CE	0
+#define EEPROM_READ	0x80
+
+/*
+;==========================================================
+;	AMD 53C974 Registers bit Definition
+;==========================================================
+*/
+/*
+;====================
+; SCSI Register
+;====================
+*/
+
+/*; Command Reg.(+0CH) (rw) */
+#define DMA_COMMAND		BIT7
+#define NOP_CMD 		0
+#define CLEAR_FIFO_CMD		1
+#define RST_DEVICE_CMD		2
+#define RST_SCSI_BUS_CMD	3
+
+#define INFO_XFER_CMD		0x10
+#define INITIATOR_CMD_CMPLTE	0x11
+#define MSG_ACCEPTED_CMD	0x12
+#define XFER_PAD_BYTE		0x18
+#define SET_ATN_CMD		0x1A
+#define RESET_ATN_CMD		0x1B
+
+#define SEL_WO_ATN		0x41	/* currently not used */
+#define SEL_W_ATN		0x42
+#define SEL_W_ATN_STOP		0x43
+#define SEL_W_ATN3		0x46
+#define EN_SEL_RESEL		0x44
+#define DIS_SEL_RESEL		0x45	/* currently not used */
+#define RESEL			0x40	/* " */
+#define RESEL_ATN3		0x47	/* " */
+
+#define DATA_XFER_CMD		INFO_XFER_CMD
+
+
+/*; SCSI Status Reg.(+10H) (r) */
+#define INTERRUPT		BIT7
+#define ILLEGAL_OP_ERR		BIT6
+#define PARITY_ERR		BIT5
+#define COUNT_2_ZERO		BIT4
+#define GROUP_CODE_VALID	BIT3
+#define SCSI_PHASE_MASK 	(BIT2+BIT1+BIT0) 
+/* BIT2: MSG phase; BIT1: C/D physe; BIT0: I/O phase */
+
+/*; Interrupt Status Reg.(+14H) (r) */
+#define SCSI_RESET		BIT7
+#define INVALID_CMD		BIT6
+#define DISCONNECTED		BIT5
+#define SERVICE_REQUEST 	BIT4
+#define SUCCESSFUL_OP		BIT3
+#define RESELECTED		BIT2
+#define SEL_ATTENTION		BIT1
+#define SELECTED		BIT0
+
+/*; Internal State Reg.(+18H) (r) */
+#define SYNC_OFFSET_FLAG	BIT3
+#define INTRN_STATE_MASK	(BIT2+BIT1+BIT0)
+/* 0x04: Sel. successful (w/o stop), 0x01: Sel. successful (w/ stop) */
+
+/*; Clock Factor Reg.(+24H) (w) */
+#define CLK_FREQ_40MHZ		0
+#define CLK_FREQ_35MHZ		(BIT2+BIT1+BIT0)
+#define CLK_FREQ_30MHZ		(BIT2+BIT1)
+#define CLK_FREQ_25MHZ		(BIT2+BIT0)
+#define CLK_FREQ_20MHZ		BIT2
+#define CLK_FREQ_15MHZ		(BIT1+BIT0)
+#define CLK_FREQ_10MHZ		BIT1
+
+/*; Control Reg. 1(+20H) (rw) */
+#define EXTENDED_TIMING 	BIT7
+#define DIS_INT_ON_SCSI_RST	BIT6
+#define PARITY_ERR_REPO 	BIT4
+#define SCSI_ID_ON_BUS		(BIT2+BIT1+BIT0) /* host adapter ID */
+
+/*; Control Reg. 2(+2CH) (rw) */
+#define EN_FEATURE		BIT6
+#define EN_SCSI2_CMD		BIT3
+
+/*; Control Reg. 3(+30H) (rw) */
+#define ID_MSG_CHECK		BIT7
+#define EN_QTAG_MSG		BIT6
+#define EN_GRP2_CMD		BIT5
+#define FAST_SCSI		BIT4	/* ;10MB/SEC */
+#define FAST_CLK		BIT3	/* ;25 - 40 MHZ */
+
+/*; Control Reg. 4(+34H) (rw) */
+#define EATER_12NS		0
+#define EATER_25NS		BIT7
+#define EATER_35NS		BIT6
+#define EATER_0NS		(BIT7+BIT6)
+#define REDUCED_POWER		BIT5
+#define CTRL4_RESERVED		BIT4	/* must be 1 acc. to AM53C974.c */
+#define NEGATE_REQACKDATA	BIT2
+#define NEGATE_REQACK		BIT3
+
+#define GLITCH_TO_NS(x) (((~x>>6 & 2) >> 1) | ((x>>6 & 1) << 1 ^ (x>>6 & 2)))
+#define NS_TO_GLITCH(y) (((~y<<7) | ~((y<<6) ^ ((y<<5 & 1<<6) | ~0x40))) & 0xc0)
+
+/*
+;====================
+; DMA Register
+;====================
+*/
+/*; DMA Command Reg.(+40H) (rw) */
+#define READ_DIRECTION		BIT7
+#define WRITE_DIRECTION 	0
+#define EN_DMA_INT		BIT6
+#define EN_PAGE_INT		BIT5	/* page transfer interrupt enable */
+#define MAP_TO_MDL		BIT4
+#define DIAGNOSTIC		BIT2
+#define DMA_IDLE_CMD		0
+#define DMA_BLAST_CMD		BIT0
+#define DMA_ABORT_CMD		BIT1
+#define DMA_START_CMD		(BIT1+BIT0)
+
+/*; DMA Status Reg.(+54H) (r) */
+#define PCI_MS_ABORT		BIT6
+#define BLAST_COMPLETE		BIT5
+#define SCSI_INTERRUPT		BIT4
+#define DMA_XFER_DONE		BIT3
+#define DMA_XFER_ABORT		BIT2
+#define DMA_XFER_ERROR		BIT1
+#define POWER_DOWN		BIT0
+
+/*; DMA SCSI Bus and Ctrl.(+70H) */
+#define EN_INT_ON_PCI_ABORT	BIT25
+#define WRT_ERASE_DMA_STAT	BIT24
+#define PW_DOWN_CTRL		BIT21
+#define SCSI_BUSY		BIT20
+#define SCLK			BIT19
+#define SCAM			BIT18
+#define SCSI_LINES		0x0003ffff
+
+/*
+;==========================================================
+; SCSI Chip register address offset
+;==========================================================
+;Registers are rw unless declared otherwise 
+*/
+#define CtcReg_Low	0x00	/* r	curr. transfer count */
+#define CtcReg_Mid	0x04	/* r */
+#define CtcReg_High	0x38	/* r */
+#define ScsiFifo	0x08
+#define ScsiCmd 	0x0C
+#define Scsi_Status	0x10	/* r */
+#define INT_Status	0x14	/* r */
+#define Sync_Period	0x18	/* w */
+#define Sync_Offset	0x1C	/* w */
+#define Clk_Factor	0x24	/* w */
+#define CtrlReg1	0x20	
+#define CtrlReg2	0x2C
+#define CtrlReg3	0x30
+#define CtrlReg4	0x34
+#define DMA_Cmd 	0x40
+#define DMA_XferCnt	0x44	/* rw	starting transfer count (32 bit) */
+#define DMA_XferAddr	0x48	/* rw	starting physical address (32 bit) */
+#define DMA_Wk_ByteCntr 0x4C	/* r	working byte counter */
+#define DMA_Wk_AddrCntr 0x50	/* r	working address counter */
+#define DMA_Status	0x54	/* r */
+#define DMA_MDL_Addr	0x58	/* rw	starting MDL address */
+#define DMA_Wk_MDL_Cntr 0x5C	/* r	working MDL counter */
+#define DMA_ScsiBusCtrl 0x70	/* rw	SCSI Bus, PCI/DMA Ctrl */
+
+#define StcReg_Low	CtcReg_Low	/* w	start transfer count */
+#define StcReg_Mid	CtcReg_Mid	/* w */
+#define StcReg_High	CtcReg_High	/* w */
+#define Scsi_Dest_ID	Scsi_Status	/* w */
+#define Scsi_TimeOut	INT_Status	/* w */
+#define Intern_State	Sync_Period	/* r */
+#define Current_Fifo	Sync_Offset	/* r	Curr. FIFO / int. state */
+
+
+#define DC390_read8(address)			\
+	(inb (pACB->IOPortBase + (address)))
+
+#define DC390_read8_(address, base)		\
+	(inb ((u16)(base) + (address)))
+
+#define DC390_read16(address)			\
+	(inw (pACB->IOPortBase + (address)))
+
+#define DC390_read32(address)			\
+	(inl (pACB->IOPortBase + (address)))
+
+#define DC390_write8(address,value)		\
+	outb ((value), pACB->IOPortBase + (address))
+
+#define DC390_write8_(address,value,base)	\
+	outb ((value), (u16)(base) + (address))
+
+#define DC390_write16(address,value)		\
+	outw ((value), pACB->IOPortBase + (address))
+
+#define DC390_write32(address,value)		\
+	outl ((value), pACB->IOPortBase + (address))
+
+
+#endif /* _TMSCSIM_H */